388687
8
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
8
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the
plug
If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left
unattended
USE
• Charging battery 5
- battery of new tools is not fully charged
! remove battery from charger after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- after 3 hours the charging operation will be
completed, and the battery may be used, even
though the red light may still be on (the red light
may require more than 3 hours to turn off)
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- ensure that the outside surface of the battery is clean
and dry before inserting into charger
- do not charge at temperatures below 0°C and over
40°C; this will seriously damage the battery as well
as the charger
- do not remove battery from tool while it is running
! a battery that is new or has not been used for a
longer period does not develop its full capacity
until after approximately 5 charging/discharging
cycles
- do not repeatedly recharge the battery after only a
few minutes of operation; this may result in a
reduction of operating time and battery effi ciency
- the nickel-cadmium battery must be kept separate
from the natural environment and should not be
disposed of as normal domestic waste (symbol 6
will remind you of this when the need for disposing
occurs)
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
- if you anticipate long periods of non-use for the tool,
it is best to unplug the charger from its power source
• On/off 7
Speed control for smooth starting 8
Changing direction of rotation 9
- when not properly set in left/right position, switch
A 2 cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Changing bits 0
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
Torque control (VariTorque) !
- limits the amount of output torque delivered by the
chuck (6 clutch settings)
- when turning in a screw, fi rst try VariTorque position 1
and increase until the desired depth has been
reached
Holding and guiding the tool @
- keep the ventilation slots uncovered
- do not apply too much pressure on the tool; let the
tool do the work for you
APPLICATION ADVICE
Use the appropriate bits #
! only use sharp bits
When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
When screwdriving in hard wood one should pre-drill a
hole
Splinterfree drilling in wood $
Dustfree drilling in walls %
Dustfree drilling in ceilings ^
Drilling in tiles without skidding &
For more tips see www.skileurope.com
GUARANTEE / ENVIRONMENT
Keep tool and charger clean
- the charger may be cleaned most effectively with
compressed air (wear safety goggles)
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source before
cleaning
This SKIL product is guaranteed in accordance with
statutory/country-specifi c regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
In case of a complaint, send the tool or charger
undismantled together with proof of purchase to your
dealer or the nearest SKIL service station (addresses as
well as the service diagram of the tool are listed on
www.skileurope.com)
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol * will remind you of this when the need for
disposing occurs
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 2301 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 2301 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info