479914
6
Verklein
Vergroot
Pagina terug
1/128
Pagina verder
6
In case of electrical or mechanical
malfunction, immediately switch off
the tool or unplug charger from power
source
SKIL can assure fl awless functioning
of the tool only when original
accessories are used
The tool/charger is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision or
instruction concerning use of the tool/
charger by a person responsible for
their safety
Ensure that children do not play with
the tool/charger
Be careful not to drive into areas
where electrical wires may be
contacted
Ensure that switch B 2 is in the
middle (locking) position before
making any adjustments or changing
accessories as well as when carrying
or storing the tool
CHARGING/BATTERIES
Charge battery only with the charger
that is supplied with the tool
Do not expose tool/charger to rain
Never charge battery outdoors 4
Store tool/charger in locations where
temperature will not exceed 40°C or
drop below 0°C
Batteries may explode when disposed
of in fi re, so do not burn battery for
any reason
Do not use charger when cord or plug
is damaged; cord or plug should be
replaced immediately at one of the
offi cially registered SKIL Service
Stations
Do not disassemble charger or tool
Do not attempt to recharge non-
rechargeable batteries
USE
• Charging battery 5
- battery of new tools is not fully
charged
- after approximately 5 hours the
battery is fully charged
! unplug the charger from the tool
after charging period has ended
thereby lengthening the service
life of the battery
IMPORTANT:
- while charging, the charger and the
battery may become warm to touch;
this is normal and does not indicate
a problem
- do not charge at temperatures
below 0°C and over 40°C; this will
seriously damage the battery as well
as the charger
! a battery that is new or has not
been used for a longer period
does not develop its full capacity
until after approximately 5
charging/discharging cycles
- do not repeatedly recharge the
battery after only a few minutes of
operation; this may result in a
reduction of operating time and
battery effi ciency
- the battery must be kept separate
from the natural environment and
should not be disposed of as normal
domestic waste (symbol 6 will
remind you of this when the need for
disposing occurs)
! prior to disposal protect battery
terminals with heavy tape to
prevent short-circuit
- if you anticipate long periods of non-
use for the tool, it is best to unplug
the charger from its power source
• On/off 7
Changing direction of rotation 8
- when not properly set in left/right
position, switch A 2 cannot be
activated
! change direction of rotation only
when tool is at a complete
standstill
• Changing bits 9
- push bit to end position in bitholder
! do not use bits with a damaged
shank
• Automatic spindle-lock
Allows you to manually tighten or
loosen screws, when necessary 0
APPLICATION ADVICE
Use the appropriate bits !
! do not use damaged bits
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 2148 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 2148 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info