701698
10
Verklein
Vergroot
Pagina terug
1/148
Pagina verder
10
Mounting of accessories 8
! disconnect the plug
- clean spindle C and all parts to be mounted
- screw VELCRO backing pad D onto spindle C while
pushing spindle-lock button E
! push spindle-lock button E only when spindle C
is at a standstill
- simply press polishing pad F, G or H onto VELCRO
backing pad D
- for removing accessories handle vice-versa
Before using the tool
- ensure that accessory is correctly mounted and rmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 60 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
On/o
- switch on/o the tool by pulling/releasing trigger J 2
Electronic soft-start
Ensures reaching the maximum speed smoothly without
a sudden impact when tool is switched on
Switch locking for continuous use
- pull trigger J
- press knob K with your thumb
- unlock the switch by pulling again trigger J and then
releasing it
Speed control 9
- with wheel L the maximum speed can be adjusted
from low to high (1-6)
- start with wheel L in position 1 (lower speed)
- if needed, select a higher speed while the tool runs
- the optimal working speed depends on the material
and can be determined with practical trials
Operating the tool
- switch on the tool
- place the tool fully on the surface to be polished and
move it evenly by sections
- one move should overlap the previous move by one
half
- do not stop at a single spot to avoid burning the
coating
- do not move the tool in circles to avoid staining or
burning the coating
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
! dirty polishing pads cause swirl marks, so keep
them clean
Holding and guiding the tool 0
! while working, always hold the tool at the
grey-coloured grip area(s)
- always hold the tool rmly with both hands, so you will
have full control of the tool at all times
- provide for a secure stance
! do not apply so much pressure on the tool that it
comes to a standstill
- keep ventilation slots M 2 uncovered
APPLICATION ADVICE
For optimal results !
For more tips see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Protect the tool from impact, shock and grease
Always keep tool and cord clean (especially ventilation
slots M 2)
! disconnect the plug before cleaning
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
Clean the polishing pads with water after use
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONMENT
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
Measured in accordance with EN 60745 the sound
pressure level of this tool is 98 dB(A) and the sound
power level 109 dB(A) (standard deviation: 3 dB), and the
vibration 4.8 m/s² (triax vector sum; uncertainty K = 1.5
m/s²)
The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 1144 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 1144 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 6,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info