480087
11
Verklein
Vergroot
Pagina terug
1/204
Pagina verder
11
- do not over reach and do not cut above shoulder
height (this helps prevent unintended tip contact
and enables better control of the chain saw in
unexpected situations)
- only use replacement bars and chains specified
by the manufacturer (incorrect replacement bars
and chains may cause chain breakage and/
or kickback)
- follow the manufacturer’s sharpening and
maintenance instructions for the saw chain
(decreasing the depth gauge height can lead to
increased kickback)
PERSONAL SAFETY
It is recommended that the rst time user should have
practical instruction in the use of the chainsaw and the
protective equipment from an experienced operator and
that the initial practice should be cutting logs on a saw
horse or cradle
Do not touch rotating chain
Do not operate chain saw near other people,
children or animals
Do not operate chain saw after drinking alcohol
or under the influence of intoxicating drugs
or medication
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the tool by a person responsible
for their safety
Ensure that children do not play with the tool
ELECTRICAL SAFETY
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
Only use an extension cord which is intended for
outdoor use and equipped with a watertight plug
and coupling-socket
Only use extension cords with a maximum length of
20 metres (1,5 mm²) or 50 metres (2,5 mm²)
Always switch o tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (do not touch the cord
before disconnecting the plug)
Protect the (extension) cord from heat, oil and
sharp edges
Never use the cord for carrying, pulling or unplugging
the tool
Inspect the cord periodically and have it replaced by
a qualied person, if damaged
Inspect the extension cord periodically and replace it,
if damaged (inadequate extension cords can
be dangerous)
Do not use the tool if the switch does not turn it on and
o; always have a damaged switch repaired by a
qualied person
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Always switch off tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (do not touch the cord before
disconnecting the plug)
5 Do not expose tool to rain
6 Wear protective glasses and hearing protection
7 Double insulation (no earth wire required)
8 Do not dispose of the tool together with household
waste material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
Assembly 9
! do not connect the chain saw to mains before
it is completely assembled
! always use gloves when handling the chain
- place the chain saw on any suitable at surface
- remove cover plate A by turning locking knob
B counter-clockwise
- slide chain C in the slot around chain bar D
! ensure chain is in correct running direction by
comparing with chain symbol E
- t the chain onto drive sprocket F and guide chain
bar D, so that fastening bolt G and the two guide
ns H t into the keyway of chain bar D, and that
chain tensioning peg J ts into the respective hole
of chain bar D
- if necessary, turn tensioning knob K to bring tensioning
peg J in alignment with the hole in chain bar D
- check if all parts are seated properly and hold chain
and chain bar in a level position
- turn tensioning knob K until all the slack is taken up in
the chain
- mount cover plate A as illustrated
- tighten locking knob B on fastening bolt G by turning
it clockwise
Tensioning chain 0
- place the chain saw on any suitable at surface
- check if the chain links are correctly located in the slot
around chain bar D
1) loosen locking knob B until it is just holding chain bar
in position (do not remove)
2) lift the chain bar somewhat and hold it in that position
3) turn chain tensioning knob K upwards until the lowest
chain links come up and JUST touch the bottom of
chain bar D
4) tighten locking knob B by turning it clockwise
5) release chain bar
6) the correct chain tension is reached when the chain can
be raised approx. 4 mm from the chain bar in the centre
! always check the chain tension before use, after
the first cuts and regularly during use (approx.
every 10 minutes)
- upon initial operation, new chains can
lengthen considerably
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 0780 AA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 0780 AA in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 11,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info