480089
8
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
8
Only operate the tool in open space (not too close to a
wall or other solid objects) and on a rm, level surface
Store the tool indoors in a dry and locked-up place, out
of reach of children
BEFORE USE
Check that all screws, nuts, bolts and other fasteners are
properly secured and that guards and screens are in place
Ensure that the feed intake is empty
DURING USE
Keep your face and body away from the feed
intake opening
Do not allow hands (or any other part of the body) or
clothing inside the feed intake opening, outlet opening or
near any moving part
Keep proper balance and footing at all times; do
not overreach
Never stand at a higher level than the base of the tool
when feeding material
Always keep proper distance from the outlet zone when
operating the tool
When feeding material into the tool be extremely careful
that pieces of metal, rocks, bottles, cans or other foreign
objects are not included
If the cutting mechanism strikes any foreign object or if
the tool should start making any unusual noise or
vibration, immediately switch o, allow the cutting blade
to stop, disconnect the plug and take the following steps
- inspect for damage
- replace or repair any damaged parts
- check for and tighten any loose parts
Do not allow processed material to build up in the outlet
zone; this may prevent proper discharge which can result
in kickback of material through the feed intake opening
If the tool becomes clogged, switch o, allow the cutting
blade to stop and disconnect the plug before
clearing debris
Keep the motor cooling vents clean of debris and other
accumulations to prevent damage to the motor or
possible re
Do not tilt or transport the tool while the motor is running
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
Assembly instructions $
- mount wheels with the two wrenches A supplied and
assemble tool as illustrated
- position collection bag B underneath outlet C
- mount prodder holder D
On/o %
- switch on/o the tool by pushing switch E in
“I”/”O” position
! after switching off the tool the blade continues to
rotate for a few seconds
- allow the cutting blade to stop rotating before
switching on again
! the tool will not start unless securing knob F is
fully tightened
! do not rapidly switch on and off
Restart protection
- after a power supply failure the tool will not restart on
its own
- use switch E % for restarting the tool
Overload protection
Overloading (e.g. blocking up the cutting blade) can lead
to a standstill of the tool
- wait a short period before switching on the tool again
- restart tool by rst pushing button G % and then
switch E %
Shredding ^
- feed the material to be chopped through feed intake
opening H
- only insert as much material so that the feed intake will
not be blocked up
! longer material could lash out when being cut
! small pieces of shredded material may be ejected
from the feed intake opening
! wear safety glasses, hearing protection and
protective gloves when using the tool
- do not ll soft waste such as kitchen rubbish into
the shredder
- ensure that the chopped material can fall freely from
outlet C
- ensure that ventilation slots J 2 will not be covered by
the collection bag or the chopped material
- avoid blocking outlet C with shredded material as this
could result in kickback of material through feed intake
opening H
Removing blockage &
! switch off the tool and disconnect the plug
- loosen securing knob F and open the tool as illustrated
- clean the blade area (remove compacted debris with a
woorden or plastic implement)
- also clean outlet C of any debris
- close the tool and tighten securing knob F rmly
Reversing/changing cutting blade *
! switch off the tool and disconnect the plug
- the cutting blade has a cutting edge on both sides; so
if one side has become blunt, the other side can
be used
- replace the cutting blade when both sides are blunt
(SKIL spare part number 2610Z02553,
marked YAT 8231-545201)
- loosen securing knob F and open the tool as illustrated
- loosen both blade bolts with hex key L while using
metal plate M as support
- reverse and mount the cutting blade as illustrated
- tighten both blade bolts with hex key L while using
metal plate M as support
- close the tool and tighten securing knob F rmly
APPLICATION ADVICE
For best results shred fresh branches soon after they
have been cut
Use prodder K for feeding soft material (
Shred soft garden waste in smaller loads, particularly
when wet
Blockages can be avoid by intermittently
shredding branches
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 0770 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 0770 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info