● Projecting points 0
For making references on a longer distance
- place the tool on a flat surface or on the tripod
- level the tool in case of horizontal or vertical
reference lines
- switch on the tool
- align the projected laser point with your target point
by turning rotary head D manually
! check the leveling after each adjustment
● Projecting plumb points !
- place the tool on a flat surface
- level the tool
- switch on the tool
- a plumb point is projected on the ceiling
! check the leveling after each adjustment
● Working with wall-mounted tool @
For work exceeding the extension height of tripods, the
tool can be mounted to the wall as illustrated
! ensure the tool is mounted properly and cannot
fall down
● Laser viewing glasses #
- for improving the view of the laser line
! these glasses will not protect your eyes against
laser radiation
● Mounting of tool on tripod $%
- unfold the tripod
- lock the tripod with ring Q
- adjust length of 3 legs with clips R
- adjust length of rod S with handle T
- lock rod S with knob U
- mount tool on tripod as illustrated
- use adapter P for mounting tool in vertical position
● When working with the tripod on uneven surfaces, level
the tripod itself by adjusting leg lengths with clips R 3
and checking bubble level V 3
● When using the tripod the tool can be used in any
inclined position for projecting lines under any desired
angle
MAINTENANCE
● Do not expose the tool to continuous vibration or
extremely hot or cold temperatures
● Always store the tool indoors in its protective bag
● Always keep the tool free of dust, moisture and direct
sunlight
● Clean the tool with a damp cloth
● Do not disassemble or modify the tool in any way
● Do not attempt to change any part of the laser lens
GUARANTEE / ENVIRONMENT
● This Skil product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
● In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest Skil service-station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
● Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ^ will remind you of this when the need for
disposing occurs
Niveau laser à 360° 560
INTRODUCTION
● Cet outil sert à la projection et au contrôle des plans
horizontaux et verticaux, ainsi que des points
(perpendiculaires) de projection
● Lisez soigneusement ce mode d'emploi ainsi que
l'étiquette d'avertissement située sur l'outil avant
d'utiliser l'outil 1
● Prêtez attention aux consignes de sécurité et aux
avertissements; sinon, vous risquez d'endommager
gravement vos yeux
● Conservez ce mode d'emploi pour vous y reporter à
l'avenir
SPECIFICATIONS TECHNIQUES
Type de laser 635 nm
Catégorie de laser 2
Puissance de sortie ≤ 1 mW
Alimentation 2 piles D (LR20) / 1,5V
Température de fonctionnement -1°C à 40°C
Température de stockage -10°C à 40°C
Poids 1,3 kg
Exactitude +/- 0,7 mm/m
SECURITE
● Ne projetez pas le rayon laser dans vos yeux
(rayonnement laser) 2
● Ne dirigez pas le rayon laser vers des personnes ou
des animaux
● N'utilisez pas d'outils optiques grossissants (loupes,
télescopes ou jumelles) pour voir le rayon laser
● Veillez à ne pas enlever l'étiquette d'avertissement de
l'outil ni à l'endommager
● N'utilisez pas cet outil en la présence de liquides
inflammables, de gaz ou de poussière
● N'utilisez pas cet outil en la présence d'enfants
● Cet outil ne doit pas être utilisé par des personnes de
moins de 16 ans
● N'utilisez pas cet outil dans un but autre que ceux
mentionnés dans ce mode d'emploi
● Utilisez seulement les accessoires d'origine prévus pour
cet outil
