758630
12
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
12
Battery protection
The tool is suddenly being switched o or prevented from
being switched on, when
-the load is too high --> remove load and restart
-the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start ashing when
pressing button G qc; wait until battery has returned
within the allowable operating temperature range
-the battery is nearly empty (to protect against
deep discharge) --> a low battery level or ashing low
battery level qb is shown by the battery level indicator
when pressing button G; charge battery
! 

damaged
Trimming
! ensure that the cutting area is free of stones,
debris and other foreign objects
! start trimming only when tool runs at full speed
-cut long grass in layers (always start from the top)
-only trim with the tip of the cutting line
-do not cut damp or wet grass
-prevent the cut grass from clogging the spool (do not
make heavy cuts)
-do not overload the tool
-carefully cut around trees and bushes, so that they do
not come into contact with the cutting line
-keep the tool away from solid objects in order to protect
the cutting line against excessive wear
-be aware of the kickback forces that occur when solid
objects are touched
Holding and guiding the tool u
-for cutting long grass slowly swing the tool from right to
left and vice versa
-hold tool rmly with both hands, so you will have full
control of the tool at all times
-maintain a stable working position
-always hold the tool well away from your body
Line feeding i
-tap trimmer head lightly on a solid surface while the
motor is running
! tap trimmer head on bare ground or hard soil,
when tapping in tall grass, the motor may overheat
-the cutting line will be released and cut o to the correct
length by line cutting blade K
! take care against injury from line cutting blade K
-feed the lines regularly to maintain full cutting circle
-when the motor runs without load and no grass is cut,
the cutting line is stuck, worn or broken; rewind or
replace the line
Feeding the line manually
-switch o the tool and remove the battery
-press the trimmer head and pull the lines to feed the
line manually and check for proper installation
-after line feeding always return the tool to its normal
operating position before switching on
-when the motor runs without load and no grass is cut,
the cutting line is stuck, worn or broken; rewind or
replace the line
Line replacement o
In case the cutting line fails to protrude from spool hole Q
! 
BATTERIES
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
rst time)
Only use the following batteries and chargers with
this tool
-SKIL battery: BR1*31****
-SKIL charger: CR1*31****
Do not use the battery when damaged; it should be
replaced
Do not disassemble the battery
Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
-when charging 4...40°C
-during operation –20...+50°C
-during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in re, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 
debris (keep bystanders a safe distance away from work
area)
7 Wear protective glasses and hearing protection
8 Do not expose tool to rain
9 Do not dispose of electric tools and batteries together
with household waste material
USE
Assembly instructions
-unfold hinge F and x as illustrated with 2 screws w
-mount the guide handle C as illustrated e
-guide handle C can be adjusted by loosening/
tightening knob D
-mount cutting guard J as illustrated with 2 screws r
! never use the tool without cutting guard J
Charging battery
! read the safety warnings and instructions
provided with the charger
Removing/installing the battery 2
On/o t
-switch on tool by rst pressing knob A (= safety switch
which cannot be locked) and then pulling trigger B
-switch o tool by releasing trigger switch B
! 
continues to rotate for a few seconds
-allow the cutting line to stop rotating before switching
on again
! 
Speed selection y
-set selector E to desired speed
Battery level indicator q
-press the battery level indicator button G to show the
current battery level qa
! when the lowest level of the battery indicator
qb, the
battery is empty
! 
after pressing button G qc, the battery is not
within the allowable operating temperature range
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 0250 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 0250 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info