23326
11
Verklein
Vergroot
Pagina terug
1/268
Pagina verder
Simrad PI32
Catch monitoring system
Operator manual
M A X I M I Z I N G Y O U R P E R F O R M A N C E A T S E A
www.simrad.com
857-164636 / Rev.A
Simrad PI32
Catch monitoring system
Operator manual
Important notice
Operation of the PI32 Catch monitoring system
assumes that the communication between the
Operator Unit and the sensors is fully functional.
Ensure that the communication channels and update
rates defined on the Operator Unit matches those of
the sensors.
About this document
Rev Date Written by Checked by Approved by
Rev.A
04.12.05 RBr KRa KRa
Original issue
© 2005 Simrad AS
ISBN 82-8066-059-3
All rights reserved. No part of this work covered by the copyright her eon may be
reproduced or otherwise copied without prior permission from Simrad AS.
The information contained in this document is subject to change without prior notice.
Simrad AS shall not be liable for errors contained herein, or for incidentalor consequential
damages in connection with the furnishing, performance, or use of this document.
The equipment to which this manual applies must only be used for the purpose for which
itwasdesigned.Improperuseormaintenancemaycausedamagetotheequipment orinjury
to per sonnel. T he user must befamiliar withthecontentsoftheappropriate manuals before
attempting to operate or work on the equipment. Simrad AS disclaims any responsibility
for damage or injury causedbyimproper installation, useormaintenanceof the equipment.
If you require maintenance on your Simrad equipment, contact your local dealer. You can
also contact Simrad using the following e-mail address: fish-support@simrad.com
Operator manual
I
857-164636 / Rev.A
Sections
1Introduction
This section introduces the PI32 C atch monitoring system operator manual.
Refer to page 1.
2 System description
This section provides a general introduction to the PI32 C atch monitoring
system and the units in use. Refer to page 2.
3 Getting started
This section provides general guidelines to help you get started with the PI32
Catch monitoring system. Refer to page 8.
4 Applications
This section gives an overview of the various applications that the PI32 can
offer. Refer to page 20.
5 Display modes
This section gives an in--depth description of all the display presentations.
Refer to page 27.
6 Operational procedures
This section provides detailed procedures to guide you through the most
common functions. Refer to page 45.
7 Practical use of the sensors
This section describes how to install and use each sensor type. Both PI and PS
sensors are described and explained. Refer to page 83.
8 Sensor chargers
This section describes how to install and use t he sensor chargers. Refer to page
144.
9Menusystem
This section allows you to access the reference information from t he menu
structure. Refer to page 149.
10 References
This section details the various setup pages, those selected from the menu
system and those accessed from the display presentation. Refer to page 152.
11 PI Configurator
This section explains how to use the PI Configurator utility to change the
sensors communication channel and update rate. Refer to page 184.
Simrad PI32
II
857-164636 / Rev.A
12 Sensor test procedures
This section provides simple test procedure you can use to verify the the sensors
are working properly. Refer to page 223.
13 Technical specifications
This section provides the basic technical specifications. Refer to page 243.
Operator manual
III
857-164636 / Rev.A
INTRODUCTION 1..............................................
SYSTEM DESCRIPTION 2......................................
System diagram 3..........................................
Operator Unit 4...........................................
Hull mounted and portable hydrophones 5......................
Sensor overview 6.........................................
Battery chargers 7..........................................
GETTING STARTED 8...........................................
How to s witch power on and off 9.............................
Defining initial presentation pages 10...........................
Introduction to the main menu 12..............................
Introduction to t he keypad 13.................................
Introducing the sensors 15....................................
APPLICATION EXAMPLES 20....................................
Purse seine 21..............................................
Danish seine 22............................................
Bottom trawl 23............................................
Pelagic trawl 24............................................
Echo sounder 25............................................
Graphic display 26..........................................
DISPLAY PRESENTATIONS 27..................................
Numeric display 28.........................................
Graphic display 35..........................................
Surface temperature 37.......................................
Status display 38...........................................
Echo sounder display 40.....................................
Navigation display 43.......................................
Position display 44..........................................
OPERATIONAL PROCEDURES 45................................
Overview 45...............................................
How to define sensor presentation 46...........................
How to set up the sensors 48..................................
How to m ount the sensors on the net 51.........................
How to use the sensors 52....................................
How to replace the sacrificial water switch 53....................
How to test the sensors 54....................................
How to calibrate the Depth sensor 55...........................
How to define sensor offsets 56................................
Simrad PI32
IV
857-164636 / Rev.A
How to set up a Twin Spread sensor for twin trawl applications 57....
How to access graphic display parameters 62.....................
How to view echo sounder data 63.............................
How to set up marker lines 64.................................
Special features for trawl marker lines 67........................
How to access echo sounder parameters 69.......................
How to use visual aids and filters 70............................
How to define echo sounder range 72...........................
How to zoom in on bottom echoes 74...........................
How to zoom in on pelagic echoes 75...........................
How to enable A-Scope presentation 76.........................
How to define alarm limits 77.................................
How to select menu language 80...............................
How to control automatic page rotation 81.......................
How to restore default settings 82..............................
PRACTICAL USE OF THE SENSORS 83..........................
Sensor configuration 84......................................
PI Bottom Contact sensor 87..................................
PS Bottom Contact sensor 91.................................
PI Catch sensor 95..........................................
PS Catch sensor 100..........................................
PI Depth sensor 104..........................................
PS Depth sensor 109.........................................
PI Height sensor 114.........................................
PI Rip sensor 118............................................
PI Spread and Remote sensors 123..............................
PI Twin Spread 128..........................................
PI Temperature sensor 133.....................................
PS Temperature sensor 139....................................
SENSOR CHARGERS 144..........................................
Overview 144...............................................
PI Charger 145..............................................
PS30 Charger 147...........................................
MENU SYSTEM 149................................................
The main menu 150..........................................
REFERENCES 152..................................................
Depth calibration 153.........................................
Echo presentation setup 154....................................
Echo sounder setup 157.......................................
Operator manual
V
857-164636 / Rev.A
Factory presets 159..........................................
Graphic setup 160...........................................
Interface setup NMEA 162....................................
Interface setup remote/alarm 167................................
Navigation setup 168.........................................
Numeric setup 169...........................................
Offset adjust 170............................................
Page setup 171..............................................
Palette setup 172............................................
Position display setup 173.....................................
Receiver setup 174...........................................
Sensor alarms 177...........................................
Sensor setup 179............................................
Speed setup 180.............................................
Surface temperature setup 181..................................
Trawl info setup 182.........................................
Units setup 183..............................................
PI CONFIGURATOR 184..........................................
Purpose 184................................................
Basic information 185........................................
About sensor configuration 187.................................
Main dialogue description 189..................................
Operational procedures 191....................................
References 198..............................................
Maintenance 219............................................
SENSOR TEST PROCEDURES 223.................................
Overview 223...............................................
Bottom C ontact test procedure 224..............................
Catch sensor, test procedure 227................................
Depth sensor, test procedure 230................................
Height sensor, test procedure 233...............................
Spread & Remote sensors test procedure 236......................
Temperature sensor, test procedure 240...........................
TECHNICAL SPECIFICATIONS 243...............................
Sensors 244................................................
INDEX 249.........................................................
Simrad PI32
VI
857-164636 / Rev.A
Sensors
Use this table to write down the sensors you use on your PI32 Catch monitoring system.
Sensor
type
Serial
number
Communication
channel
Update
rate
Operator manual
VII
857-164636 / Rev.A
Sensors
Use this table to write down the sensors you use on your PI32 Catch monitoring system.
Sensor
type
Serial
number
Communication
channel
Update
rate
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Simrad PI32 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Simrad PI32 in de taal/talen: Engels als bijlage per email.

De handleiding is 10,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Simrad PI32

Simrad PI32 Gebruiksaanwijzing - Norsk - 98 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info