572713
45
Verklein
Vergroot
Pagina terug
1/66
Pagina verder
|
45
Autopilot | NSS Installation Manual
Rudder drive setup
The rudder drive setup controls how the autopilot computer controls
the steering system.
Drive voltage
Voltage speci ed for your drive unit.
The Drive unit voltage setting does not apply when the system
operates solenoids on a continuous running pump/steering gear.
Hence, the output voltage to the solenoids will be the same as the
input voltage.
Refer to the drive unit table in the AC12/AC42 Installation manual or to your drive unit docu-
mentation for information
!
Warning: Selection of improper voltage level for your drive unit may damage both the
drive unit and the AC12/42 even if the protection circuits are activated.
Drive engage
Clutch This is the default setting and it allows you to steer the boat with the helm or
wheel when in STBY mode (FU and NFU modes) as well as in all auto steering
modes
Auto This option is typically used to switch between two rudder speeds on a continu-
ous running pump, used when di erent rudder speeds are required for auto-
matic and Follow-up/Non-Follow-up steering
Motor output
Shows the amount of power needed to achieve the correct rudder speed. The reading is
obtained from the Rudder test.
The automatically set value may be increased or decreased.
Rudder deadband
This parameter is used to prevent the rudder from hunting. The reading is obtained from the
Rudder test which optimizes the deadband to the speed of the boat and the pressure on the
rudder.
If the auto-setting does not perform properly due to high inertia from the wheel or a loose
steering gear, it can be adjusted manually. Find the lowest possible value that will prevent the
rudder from continuous hunting. A wide deadband will cause inaccurate steering.
Note: The rudder deadband setting is not available when the autopilot is con gured for
Virtual Rudder Feedback.
Seatrials
A seatrial can only be performed if the dockside settings are completed and con rmed.
The seatrial must always be performed in open waters at a safe distance from other tra c.
Note: You can switch the autopilot to standby mode and take manual control of the boat at
any time during the seatrial by pressing the
STBY/AUTO key.
The following seatrial calibration should be done:
Compass calibration; used to automatically compensate for on-board magnetic interference
Compass o set adjustment, used to compensate for a  xed o set in the  nal heading
readout
Wind calibration to compensate for a  xed mechanical o set of the Wind vane
Boat speed calibration
Transition HI/LO speed setting (the speed at which you want to change the set of steering
parameters)
Automatic tuning of the steering parameters
Setting the seastate  ler
Saiboat setup
s
s
45

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Simrad-NSS-Chartplotter

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Simrad NSS Chartplotter bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Simrad NSS Chartplotter in de taal/talen: Engels als bijlage per email.

De handleiding is 18,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Simrad NSS Chartplotter

Simrad NSS Chartplotter Gebruiksaanwijzing - English - 96 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info