28530
41
Verklein
Vergroot
Pagina terug
1/182
Pagina verder
Operational procedures
33
850-164692 / Rev.B
The polynomial model is a flexible function capable of
modelling complex function shapes. The polynomial model is
onlyusedtocheckinthePlot view that the estimated
polynomial model has the same shape as the shape of the beam
model. If the shape of the polynomial model is very different
from the shape of the beam model, this indicates that either
insufficient data have been collected, or some data points may
be associated with errors (broken cables or channel wires
mixed).
The beam model is the model actually used by the echo sounder.
The calibration program will adjust the parameters in the beam
model to minimise the RMS-error calculated on the recorded
data points. The adjusted parameters, the RMS-error, and the
data points having maximum and minimum deviation from the
model are shown in the Information view. The adjusted
parameters resulting from the beam model are the parameters,
which can be transferred to the echo sounder and used for the
transducer during operation. Information on data deviation from
the beam model will indicate how well the beam model fit the
recorded data. This can be used to evaluate the validity of the
recorded data points.
The data evaluation should start using the Plot view and the
polynomial model to check the shape of the polar plot. A
circular transducer should have a circular beam and an elliptic
transducer an ellipse, both with only insignificant offset angles.
If a circular transducer in the Plot view shows an ellipse with
approximately 45 or 135 degrees axis, the reason may be one
missing quadrant in the transducer or one missing quadrant in
the receiver. This symptom should also give approximately 2 dB
lower TS, i.e. 1dB lower transducer gain to compensate.
If a circular transducer in the Plot view shows an non circular
shape, and in addition substantial offset angles both athwart and
alongship, this indicates there may be something wrong in the
way the transducer is connected. In this case, you must select
the View menu and check the calibrated beamwidth, offset and
gain values. If one quadrant of the transducer is inversely
connected, the beamwidth will be approximately one degree too
wide, the offset angles will be approximately one degree off
centre in both directions and the calibrated gain can be in the
order of 6 dB lower than the default gain.
If two of the quadrants have been mixed up, the reference
sphere’s movements inside the beam will be incorrect. This can
be confirmed when the reference sphere is suspended in such a
way that you can move it in a specific direction. This direction
is either transversal or longitudinal in the transducer beam.
41

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Simrad ER60 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Simrad ER60 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info