679193
27
Verklein
Vergroot
Pagina terug
1/117
Pagina verder
GB
IE 23
SKV 1200 B2
Working with the blender
WARNING! RISK OF INJURY!
Always allow hot fluids to cool down to a
lukewarm temperature (approx. 30–40°C)
before adding them into the blender t.
WARNING! RISK OF INJURY FROM
SHARP BLADES/ROTATING DRIVE
UNIT!
Never put your hand into the attached
blender t!
Do not remove the blender t unless the
blades z are stationary.
Operate the blender t only when the blender
lid r with the measuring cup e are attached.
In cases of malfunction, switch the appliance
off and remove the plug from the wall socket
to prevent the appliance from being switched
back on unintentionally.
AttENtION! PrOPErty dAmAgE!
Never use the mixing bowl 6 and blender t
at the same time! This will overload the motor!
When working with the blender t we recom-
mend allowing the appliance to cool down
after 3 minutes of operation.
Proceed as follows to prepare the blender for
operation t. Use figure C on the rear fold-out
page as a guide.
1) Press down the release lever 2 and press the
swivel arm 1 downwards into the working
position.
2) Turn the drive protection cover u clockwise so
that the arrow on the drive protection cover u
is pointing to the
symbol on the appliance.
Remove the drive protection cover u and
place it to one side.
WARNING! RISK OF INJURY!
Ensure that the rotary switch 3 is turned to
"0" before you place the blender t on the
blender drive i. Otherwise the appliance will
start immediately as soon as the blender t
has locked into place.
3) Place the blender t on the blender drive unit
i so that the lock tabs on the underside of
the blender t lock into the recesses on the
blender drive unit i. The
symbol on the
blender t must be pointing to the
symbol
on the appliance. Turn the blender t anti-
clockwise as far as it will go. The symbol
on the blender t must then be pointing to the
symbol on the appliance.
4) Remove the blender lid r by turning it anti-
clockwise until it disengages from the catch on
the blender t and then pull it upwards and
off.
5) Add the ingredients.
6) Press the blender lid r
with the measuring cup e
slightly offset firmly back onto the blender t.
Close the blender lid r by turning it clockwise
as far as the stop
back into the catch
on the
blender t. Ensure that the pouring spout on
the blender t
is closed.
7) Turn the rotary switch 3 to the desired setting.
NOtE
The ideal speed depends on the consistency
of the items being mixed. The more liquid the
contents are, the faster you can mix them.
For short, powerful pulsed operation, turn
the rotary switch 3 anticlockwise to level P.
Level P does not lock into place so as not
to overload the motor. You should therefore
keep the rotary switch 3 in this position only
for a short time.
cruSHINg IcE
In order to produce crushed ice, place ice
cubes in the blender t, close it and turn the
rotary switch 3 approx. 7 times to level P
for 5 seconds. You may need to adapt the
above instructions depending on the quantity
and size of the ice cubes.
IB_292161_SKV1200B2_LB8.indb 23 22.09.17 07:53
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Silvercrest SKV 1200 B2 - IAN 292161 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Silvercrest SKV 1200 B2 - IAN 292161 in de taal/talen: Nederlands, Duits, Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 3,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info