664897
5
Verklein
Vergroot
Pagina terug
1/85
Pagina verder
SYMBOL INSTRUCTIONS
Raise needle
Raise presser foot Lower presser foot
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety should always be followed, including the
following:
Read all instructions before using this sewing machine.
-To reduce the risk of electric shock:
1. An appliance should never be left unattended when plugged in.
2. Always unplug this appliance from the electric outlet immediately after using and before
cleaning.
3. Always unplug before checking and re-lamping. Contact the manufacturer or its service agent
for repair in the event of failure if the machine is with 240mW LED lamp, which is not user-
replaceable. Replace bulb with same type rated 5 watts if the machine is with 5W lamp.
-To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Do not allow to be used as a toy. Close attention is necessary when this appliance is used by or
near children.
2. Use this appliance only for its intended use as described in this manual. Use only the attachments
recommended by the manufacturer as contained in this manual.
3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has
been dropped or damaged, or dropped into water. Return the appliance to the nearest authorized
dealer or service center for examination, repair, electrical or mechanical adjustment.
4. Never operate the appliance with any air openings block. Keep ventilation openings of the sewing
machine and foot controller free from accumulation of lint, dust, and loose cloth.
5. Keep fingers away from all moving parts. Special care is required around the sewing machine
needle.
6. Always use the proper needle plate, a wrong needle plate can cause the needle to break.
7. Do not use bent needles.
8. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
9.
10.Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or
when making any other user servicing adjustments mentioned in the instruction manual.
11.Never drop or insert any object into any opening.
12.Do not use outdoors.
13.Do not operate where aerosol spray products are being used or where oxygen is being administered.
14.To disconnect, turn all controls to the off ("O") position, then remove plug from outlet.
15.Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
DANGER
WARNING
SAVE THESE INSTRUCTIONS
Please turn off the machine or unplug when the machine is not operating properly.
18.Never place anything on the foot controller.
19.If the supply cord that is fixed with foot controller is damaged, it must be replaced by the
manufacturer or its service agent or a similar qualified person in order to avoid a hazard.
20.This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
21.Children should be supervised to ensure that they do not play with the appliance.
This sewing machine is intended for household use only.
Switch the sewing machine off ("O") when making any adjustments in the needle area, such as
threading needle, changing needle, threading bobbin, or changing presser foot, and the light.
16.The sound pressure level under normal operating conditions is 75dB(A).
17.
CONTENTS
PRINCIPAL PARTS OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
BUTTONS OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
LCD SCREEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PATTERN CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CONNECTING THE MACHINE TO THE POWER SOURCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
STARTING SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ADJUSTING THE PRESSER FOOT PRESSURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LCD BRIGHTNESS CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CHANGING THE PRESSER FOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
REPLACING THE NEEDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MATCHING NEEDLE/ FABRIC/ THREAD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
TYPE OF PRESSER FOOT CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
WINDING THE BOBBIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
INSERTING THE BOBBIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
THREADING THE UPPER THREAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
USING THE NEEDLE THREADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
THREAD TENSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RAISING UP THE LOWER THREAD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
CUTTING THE THREAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TWO-STEP PRESSER FOOT LIFTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
TO RAISE OR DROP THE FEED DOGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
OPERATION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-24
FUNCTION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-27
SELECTION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29
USEFUL SKILLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-31
STRAIGHT STITCHES AND NEEDLE POSITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
ZIGZAG STITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
STRETCH STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Operation buttons (see page 23/24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Function buttons (see page 25/26/27) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Selection buttons (see page 28/29) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connecting the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Start/stop button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Foot control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Bobbin winding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
Start/stop button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Reverse button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Auto-lock button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Needle up/ down position button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Stitch width adjustment button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Stitch length adjustment button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MODE selection button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Elongation button (see page 59). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Mirror button (see page 60) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Twin needle button (see page 61) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Direct pattern selection and number buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Clear button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Edit button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Memory button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Sewing corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Reverse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Free arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Sewing on the heavy fabric. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CONTENTS
OVERCASTING STITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
BLIND HEM/ LINGERIE STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
BUTTON SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
BUTTONHOLE STITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-40
BAR TACK STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
ADJUSTING PATTERN BALANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
EYELET STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
DARNING STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-45
ZIPPER INSERTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-47
NARROW HEMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
CORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
SATIN STITCH SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
QUILTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
GATHERING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
SMOCKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . 54-55
WALKING FOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
FAGOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
PATCHWORK STITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
SCALLOP STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
ELONGATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
MIRROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
USING THE TWIN NEEDLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
MEMORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-65
WARNING FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-67
BUZZER SOUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
REPLACING THE LIGHT BULB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-71
TROUBLE SHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72-73
QUICK ADJUSTMENT REFERENCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74-79
Using the overcasting foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Using the all purpose foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Making a buttonhole on stretch fabrics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Inserting a centered zipper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Inserting a side zipper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Single cording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Triple cording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Darning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Embroidery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Monogramming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Scallop hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Scallop edging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Combining patterns or letters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-63
Adding patterns or letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Editing patterns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Clearing patterns or letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Recalling and sewing the memorized pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Warning animation message display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Warning beeping sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Cleaning the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Cleaning the sewing machine surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Cleaning the hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-71
Instruction animation message display
3
5
4
PRINCIPAL PARTS OF THE MACHINE
1
PRINCIPAL PARTS OF THE MACHINE
Bobbin thread guide
Tension dial
Thread take-up lever
Horizontal spool pin
Hole for second spool pin
Bobbin winder
with on/off switch
Face plate
Presser foot pressure
Buttonhole lever
Auto needle threader
Needle plate
Sewing table and
accessory box
LCD screen
Handwheel
Foot controller connector
Power cord
Handle
Presser foot lifter
Drop feed lever
Thread cutter
Operation buttons
Selection buttons
Upper thread guide
Speed limiting
adjustment lever
Flip-top sewing
instruction panel
Feed balancing dial
Main power switch
Top cover
A
Function buttons
B
C
LCD screen
brightness control
* The LCD display control adjustment is only suitable for the voltage 120V/60Hz system.
2
BUTTONS OF THE MACHINE
BUTTONS OF THE MACHINE
1. Start/stop button
2. Reverse button
3. Auto-lock button
4. Needle up/down position button
Press this button to start or stop the machine.
Press this button to sew either backwards or a reinforcement stitch at a low speed.
Press this button to sew locking stitches immediately or at the end of the current patterns and
automatically stop.
Press this button to move the needle either up or down.
A. Operation buttons (see page 23/24)
5. Stitch width adjustment buttons
6. Stitch length adjustment buttons
Press these buttons to adjust the width of the zigzag stitch.
Press these buttons to adjust the length of the stitch.
B. Function buttons (see page 25/26/27)
A
C
B
1
23
4
7
5
8
6
9
0
1
2
4
5
6
9
10
11
12
13
8
7
14
3
7. Mode selection button
8. Elongation button
9. Mirror button
10.Twin needle button
Press this button to select direct mode, utility and decorative pattern mode, block letter mode,
script letter mode and outline letter mode.
A Group Patterns 28 to 51 can be elongated up to five times its normal length by pressing this
button.
Press this button to sew a reflection pattern.
Press this button to limit the maximum width when using the twin needle.
BUTTONS OF THE MACHINE
BUTTONS OF THE MACHINE
C. Selection buttons (see page 28/29)
Direct access to utility stitches by pressing the button beside the selected stitch or press the
numbers of the selected pattern.
Direct access to utility stitches by pressing the button beside the selected stitch.
If an incorrect pattern is selected or memorized, pressing this button will clear it.
Press this button to set an added pattern when sewing combinations of decorative stitches.
Direct access to utility stitches by pressing the button beside the selected stitch.
Press this button to enter or store the created patterns combination in the memory.
11.Direct pattern selection and numbered buttons
12.Direct pattern selection and clear button
13.Edit button
14.Direct pattern selection and memory button
3
LCD SCREEN
LCD SCREEN
4
Number of current unit
Total number of unit
Memory group
Pattern
to edit
Stitch width
Stitch length
Sound on/off
Auto-lock
Needle up/down position
Mirror
Stitch width
Auto-stop
Sound on/off
Needle up/down position
Auto-lock
Reverse
Pattern
number
Pattern
Tension
Needle position Stitch length
Suggested presser foot and identification letter
Pattern
Alphabet
Memory
Sound on/off
Needle up/down position
Alphabet number
Pattern
Tension
Stitch length
Suggested presser foot and identification letter
Stitch width
Mirror
The portion marked in purple on the chart shows the one unit of each pattern.below
5
PATTERN CHART
PATTERN CHART
Patterns
Direct Patterns-12
28
29
2221
23
24
25 26
27
20
30 31 32 33 34 36 3735 38 39
1618
17
1900 02 04 05 06 09 10
11
15
12
01
03
07 08
14
13
72
73
74
75
76 77 78 79
61 62 63 64 66 67 68 69 70
71
60
65
50
51
48
47
44
40
43
41 42 49
45
55
56
57
52 53 54
58
59
46
93
94 95 96 97 98 999280 81 82
83
84 85 86 88 89 9187 90
A Group Patterns-100
B Group Patterns-100
28
29
2221
23
24
25 26
27
20
30 31 32 33 34 36 3735 38 39
1618
17
1900 02 04 05 06 09 10
11
15
12
01
03
07 08
14
13
123456789 C0 M
6
PATTERN CHART
PATTERN CHART
72
73
74
75
76 77 78 79
61 62 63 64 66 67 68 69 70
71
60
65
50
51
48
47
44
40
43
41 42 49
45
55
56
57
52 53 54
58
59
46
93
94 95 96 97 98 999280 81 82
83
84 85 86 88 89 9187 90
Alphabets
Script style
01 02
03
04 05 06 07 08 09 10
11 12
13
14
1516
17
181920
21 22
23
24
25 26
27
28 29
30 31 32 33 34 35 36
37 38 39
40
41 42
43
44
45
46
47
48 49 50 51 52
53
54
55
56 57 58 59 60 61 62
63 64 65
66
67 68
69
70
71
72
73
74 75 76 77 78
79
80
81
82 83 84 85 86 87 88
89
90 91
92
93 94
95
96
97
Outline style
V
X
01 02
03
04 05 06 07 08 09 10
11 12
13
14
1516
17
181920
21 22
23
24
25 26
27
28 29
30 31 32 33 34 35 36
37 38 39
40
41 42
43
44
45
46
47
48 49 50 51 52
53
54
55
56 57 58 59 60 61 62
63 64 65
66
67 68
69
70
71
72
73
74 75 76 77 78
79
80
81
82 83 84 85 86 87 88
89
90 91
92
93 94
95
96
97
Block style
01 02
03
04 05 06 07 08 09 10
11 12
13
14
1516
17
181920
21 22
23
24
25 26
27
28 29
30 31 32 33 34 35 36
37 38 39
40
41 42
43
44
45
46
47
48 49 50 51 52
53
54
55
56 57 58 59 60 61 62
63 64 65
66
67 68
69
70
71
72
73
74 75 76 77 78
79
80
81
82 83 84 85 86 87 88
89
90 91
92
93 94
95
96
97
7
ACCESSORIES
ACCESSORIES
1. All purpose foot (T)-
2. Zipper foot (I)-
3. Buttonhole foot (D) -
4. Cording foot (M) -
5. Overcasting foot (E) -
6. Blind hem foot (F) -
7. Hemmer foot (K) -
8. Satin stitch foot (A) -
9. Quilting foot (P) -
10.Darning/ Embroidery foot -
11.Gathering foot -
12.Button sewing foot -
13.Brush/ Seam ripper -
14.Spool holder (Large) -
15.Spool holder (Small) -
16.Seam guide -
17.Bobbin(3x) -
18.Screwdriver (L & S) -
19.Pack of needle -
20.Spool pin felt -
21.Second spool pin -
22.Twin needle -
23.Walking foot -
Standard accessories
006186008
006905008
006102008
006813008
006907008
006904008
006900008
006172008
006916008
006016008
006917008
006914008
006099008
R12373210
TA10943209
006008001
006084009
006012008
006014148
006015009
R60033210
006020008
006185008
a
b
c
1
2
3
4
5
6
7
9
11
17
22
14
23
20
19
10
12
13
13
15
16
18
21
8
c
b
a
Following the directions of the arrows, you can see the three accessory storage spaces (a), (b), (c).
8
CONNECTING THE MACHINE TO THE POWER SOURCE
CONNECTING THE MACHINE TO THE POWER SOURCE
Connecting the machine
Before connecting the power supply, make sure that the voltage and the frequency shown on the
machine is conforming with your electrical power.
Place the machine on a stable table.
1. Connect the power line cord to the machine by inserting the 2-hole plug into the terminal box.
2. Connect the power line plug to the electric outlet.
3. Turn on the power switch.
4. The sewing lamp will light up when the switch is turned on.
To disconnect, turn the power switch to the off position, then remove the plug from outlet.
Polarized plug information
This appliance has a polarized plug (one blade wider than the other),
to reduce the risk of electrical shock; this plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Do not
modify the plug in any way.
Caution: Always make sure that the machine is unplugged from the power source and the
main switch is on "O". when the machine is not in use and before inserting or removing parts.
ONOFF
9
STARTING SEWING
STARTING SEWING
Start/stop button
Attention: Consult a qualified electrician if in doubt as how to connect the machine to
the power source. Unplug the power cord when the machine is not in use.
The appliance must be used with the foot controller C-9000 manufactured by CHIEN
HUNG TAIWAN., LTD.
With the sewing machine turned off,
insert the foot control plug into its
connector on the sewing machine.
Turn on the sewing machine, and then
slowly depress the foot control to start
sewing.
Release the foot control to stop the
sewing machine.
Foot control
The machine will start running when
Start/stop button is pressed and will stop
when pressed the second time.
The machine will rotate slowly at the
beginning of the sewing.
The speed limiting adjustment lever can
control the sewing speed. To increases
the speed, slide the lever to the right , To
decrease the sewing speed, slide the
lever to the left.
Please Note: The setting of the speed limiting adjustment lever will limit the maximum
speed of the machine.
ADJUSTING THE PRESSER FOOT PRESSURE
The presser foot pressure dial is on the
left of the face plate.
The presser foot pressure of the
machine has been pre-set and requires
no particular readjustment according to
the type of fabric.
For sewing with very thin fabric, reduce the
pressure by turning the knob clockwise,
and for heavy fabric, increase the pressure
by turning it counterclockwise.
ADJUSTING THE PRESSER FOOT PRESSURE
10
LCD SCREEN BRIGHTNESS CONTROL
LCD SCREEN BRIGHTNESS CONTROL
The LCD screen brightness control dial in
the upper inner cover. Use this to adjust
the sharpness of the LCD .
If no indication is shown on the screen
after switching on the power. adjust the
LCD screen brightness with the dial.
LCD screen brightness : Turn the dial to
the left direction.
screen
LCD screen darkness : Turn the dial to
the right direction.
Attention: The LCD display control
adjustment is only suitable for the
voltage 120V/60Hz system.
11
Attention: Turn power switch to off. (
when carrying out any of the above
operations!
"O")
Change the needle regularly, especially if it is
showing signs of wear and causing problems.
Insert the needle following the illustrated
instructions.
A. Loosen the needle clamp screw and tighten
again after inserting the new needle.
The flat side of the shaft should be towards the
back.
B. Insert the needle as far up as it will go.
Needles must be in perfect condition.
Problems can occur with:
- Bent needles
- Blunt needles
- Damaged points
A
B
REPLACING THE NEEDLE
REPLACING THE NEEDLE
CHANGING THE PRESSER FOOT
CHANGING THE PRESSER FOOT
(1)
Raise the presser foot bar (a). Attach the
presser foot holder (b) as illustrated.
(2)
Lower the presser foot holder (b) until
the cut-out (c) is directly above the pin (d).
Raise the lever (e).
Lower the presser foot holder (b) and the
presser foot (f) will engage automatically.
(3)
Raise the presser foot.
Raise the lever (e) and the foot will
disengages.
(4)
Attach the seam guide (g) in the slot as
illustrated. Adjust according to need for
hems, pleats, etc.
Attention: Turn power switch to off
( ) when carrying out any of the
above operations!
"O"
Attaching the presser foot holder
Attaching the presser foot
Removing the presser foot
Attaching the seam guide
e
a
b
d
c
f
e
1
2
3
g
4
b
a
MATCHING NEEDLE/ FABRIC/ THREAD
MATCHING NEEDLE/ FABRIC/ THREAD
12
Heavy duty thread, carpet thread.
16 (100)
NEEDLE, FABRIC, THREAD SELECTION GUIDE
11-14 (80-90) Medium weight fabrics-cotton,
satin, kettleclote, sailcloth, double
knits, lightweight woollens.
Medium weight fabrics-cotton
duck, woolen, heavier knits,
terrycloth, denims.
Heavyweight fabrics-canvas,
woolens, outdoor tent and quilted
fabrics, denims, upholstery
material (light to medium).
Heavy woollens, overcoat fabrics,
upholstery fabrics, some leathers
and vinyls.
14 (90)
18 (110)
NEEDLE SIZE
FABRICS THREAD
9-11 (70-80) Lightweight fabrics-thin cottons,
voile, serge, silk, muslin, Qiana,
interlocks, cotton knits, tricot,
jerseys, crepes, woven polyester,
shirt & blouse fabrics.
Light-duty thread in cotton, nylon,
polyester or cotton wrapped
polyester.
Most threads sold are medium
size and suitable for these fabrics
and needle sizes. Use polyester
threads on synthetic materials
and cotton on natural woven
fabrics for best results. Always
use the same thread on top and
bottom.
Please Note:
- In general, fine threads and needles are used for sewing fine fabrics, and thicker threads
are used for sewing heavy fabrics.
- Always test thread and needle size on a small piece of fabric which will be used for actual
sewing.
- Use the same thread for needle and bobbin.
All purpose foot (T)
Zipper foot (I)
Buttonhole foot
(D)
Cording foot (M)
Overcasting foot
(E)
Blind hem foot (F)
Hemmer foot (K)
Darning/
Embroidery foot
Gathering foot
Button sewing foot
Walking foot
APPLICATION
PRESSER FOOT
General sewing,
Patchwork stitches,
Decorative
stitching,
Smocking,
Fagoting, etc.
PRESSER FOOT
APPLICATION
Inserting zippers
Buttonhole
Cording
Overcasting
Blind hem
Narrow hemming
Satin stitch
Quilting foot (P)
Quilting
Darning
Free embroidery
Monogramming
Gathering
Button sewing
This foot helps to
prevent uneven
feeding of very
difficult fabrics
Satin stitch foot (A)
NEEDLE NEEDLE
TYPE OF PRESSER FOOT CHART
TYPE OF PRESSER FOOT CHART
(Double needle is being suggested for certain stitches for more creativity)
13
WINDING THE BOBBIN
WINDING THE BOBBIN
1. Place the thread and spool holder onto the spool pin.
For smaller spools of thread, place the spool holder
with the small side next to the spool or use the small
spool holder.
2. Snap the thread into the thread guide (Located
beneath the thread guide cover).
3. Wind the thread clockwise around the bobbin winder
tension discs.
4. Place the thread end through one of the inner holes in
the bobbin as illustrated and place the empty bobbin
on the spindle.
5. Press the bobbin winder stopper against the bobbin.
14
4
5
Bobbin winding
3
5
4
1
4
11
3
1
2
WINDING THE BOBBIN
WINDING THE BOBBIN
15
6. When the bobbin winder switch is pushed to the left,
the LCD screen will display the animation of the
bobbin winding. Push the engaging lever to the right,
and the animation will disappear. The LCD screen will
display the structure of ordinary operation.
7. Hold the thread tail securely in one hand.
8. Press the Start/stop button or the foot control.
9. After the bobbin has wound a few turns stop the
machine and cut the thread near the hole of the
bobbin. Set the speed to maximum. Continue filling
the bobbin until it is full. The motor stops automatically
when the bobbin is full.
6
7
9
10.Stop the machine, cut the thread and then remove the
bobbin.
10
Please Note: When the bobbin winder switch is placed on the left, "bobbin winding
position", the machine will not sew and the handwheel will not turn. To start sewing, push
the bobbin winder switch to the right "sewing position".
8
Attention: Turn power switch to off ("O")
before inserting or removing the bobbin.
When inserting or removing the bobbin,
the needle must be fully raised.
1. Insert the bobbin in the bobbin case with
the thread running in a counterclockwise
direction (arrow).
2. Pull the thread through the slit (A).
3. Pull the thread toward the left and along
the inside of the spring until it slips into
the notch (B) being sure that the thread
does not slip out of the slit (A).
4. Pull out about 15 cm (6 inches) of thread
and attach the bobbin cover plate. (C)
A
B
INSERTING THE BOBBIN
INSERTING THE BOBBIN
16
B
3
A
2
1
C
4
THREADING THE UPPER THREAD
THREADING THE UPPER THREAD
Please Note: It is important to carry out the threading correctly as by not doing so several
sewing problems could result.
Start by raising the needle to its highest point, and
also raise the presser foot to release the tension
discs.
1. Lift up the spool pin. Place the spool of thread on the
spool pin so that the thread comes from the front of the
spool, then place the spool cap at the end of the spool pin.
2. Draw the thread from the spool through the upper
thread guide.
3. Guide the thread around the thread guide pulling the
thread through the pre-tension spring as illustrated.
5
6
7
8
17
3
1
2
1
2
3
4
THREADING THE UPPER THREAD
THREADING THE UPPER THREAD
18
5. Then, down and around the check spring holder.
6. At the top of this movement, pass the thread from right
to the left through the slotted eye of the take-up lever
and then downwards again.
7. Pass the thread behind the flat, horizontal thread guide.
4. Thread the tension module by passing the thread
between the silver discs.
9. Pull the end of the thread through the needle from front
to the rear, and pull out about 10 cm of thread.
Use the needle threader to thread the needle. (On the
next page.)
8. Guide the thread through the wire loop.
6
7
5
9
4
USING THE NEEDLE THREADER
USING THE NEEDLE THREADER
2. The needle threader automatically turns
to the threading position and the hook pin
passes through the needle eye.
3. Take the thread in front of the needle.
4. Hold the thread loosely and release the
lever slowly. The hook will turn and pass
the thread through the needle eye forming
a loop.
Pull the thread through the needle eye.
3
Raise the needle to its highest position
and lower the presser foot.
1. Lower the needle threader lever slowly
and draw the thread through the thread
guide as illustrated and then to the right.
Attention: Turn power switch to the off
position ("O").
19
1
2
4
Upper thread
Bobbin thread
THREAD TENSION
THREAD TENSION
- Basic thread tension setting: "4"
- To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial
to the next number down.
- Proper setting of tension is important to good sewing.
- There is no single tension setting appropriate for all the stitch functions and fabrics.
- 90% of all sewing will be between "3" and "5" ("4" is basic setting).
- For all decorative sewing you will always obtain a nicer stitch and less fabric puckering when the
upper thread appears on the bottom side of your fabric.
Reverse
side
Surface
Upper thread
Bobbin thread
TightLoose
Surface
Reverse
side
Surface
Reverse
side
Surface
Reverse
side
20
1.Normal thread tension for straight stitch
sewing.
2. Thread tension is too loose for straight
stitch sewing. Turn dial to higher number.
3. Thread tension is too tight for straight stitch
sewing. Turn dial to lower number.
4. Normal thread tension for zig zag and
decorative sewing.
Upper thread
Bobbin thread
Upper thread
Bobbin thread
3
2
4
1
1. Hold the upper thread with the left
hand. Turn the handwheel towards
you (counterclockwise) lowering, then
raising the needle.
2. Gently pull on the upper thread to
bring the bobbin thread up through the
needle plate hole. The bobbin thread
will come up in a loop.
3. Pull both threads to the back under the
presser foot.
1
2
Raise the presser foot. Remove the
fabric, draw the threads to the left side of
the face cover and cut using the thread
cutter.
The threads are cut at the proper length
to start the next seam.
RAISING UP THE LOWER THREAD
RAISING UP THE LOWER THREAD
CUTTING THE THREAD
CUTTING THE THREAD
21
3
TWO-STEP PRESSER FOOT LIFTER
TWO-STEP PRESSER FOOT LIFTER
1. The presser foot lifter raises and
lowers your presser foot.
2. When sewing several layers or thick
fabrics, the presser foot can be raised
a second stage for easy positioning of
the work.
With the sewing table off the machine,
the feed dog adjustment lever can be
located at the base of the free-arm in the
back of the machine after the sewing
table have been remove.
TO RAISE OR DROP THE FEED DOGS
TO RAISE OR DROP THE FEED DOGS
Sliding the lever to the " " (b) will lower
the feed dog, for example during button
sewing. If you wish to continue sewing
normally, slide the lever to the " " (a) in
order to raise the feed dogs.
The feed dog if you do not
turn the handwheel, even if the lever is
slid to the right. Make a complete turn to
raise the feed dogs.
will not rise up
22
a
b
b
aa
2
1
23
Needle up/down
position button
Auto-lock button
Reverse button
Start/stop button
OPERATION BUTTONS
OPERATION BUTTONS
The machine will start running when start/stop
button is pressed and will stop when pressed the
second time. The machine will rotate slowly at the
beginning of the sewing.
The sewing speed can be controlled by the speed
limiting adjustment lever.
The foot control must be disconnected to
complete this operation.
Start/stop button
Reverse button
Select one pattern (except A Group Patterns 14-
27 and Direct Patterns " , , "), the machine will
sew in reverse or a reinforcement stitch at a low
speed if the reverse button is pressed. The
machine will sew forward after the button is
released.
An arrow " " on the LCD screen display indicates
reverse sewing.
OPERATION BUTTONS
OPERATION BUTTONS
When the Direct Patterns ",,,"andAGroup
Pattern " " are selected, the machine will
immediately sew 3 locking stitches when the Auto-
lock button is pressed, then automatically stop.
The LCD screen will display the figure " " until the
machine is stopped.
Auto-lock button
Select one pattern (except A Group Patterns 00,
14-27 and the Direct Patterns ",,,,,,"),
press the Auto-lock button, the machine will sew 3
locking stitches at the end of the current pattern
and automatically stop. The LCD screen will display
the figure " " until the machine is stopped.
The function will be cancelled if you press the
button once again or select another pattern.
Needle up/ down position button
With the Needle up/down position button, you
decide whether the needle shall stop in the up
position or in the material when you stop sewing.
Press the button so that the arrow, on the LCD
screen, will point upward " " and the needle will
stop in the highest position. When you press the
button so that the arrow points downward " ",
the machine will stop with the needle in the
lowest position.
24
FUNCTION BUTTONS
FUNCTION BUTTONS
Stitch width adjustment buttons
When you select a stitch, the machine will
automatically set the recommended stitch width,
which will be indicated by numbers on the LCD
screen. The stitch width can be regulated by
pressing the stitch width adjustment buttons.
Certain stitches have a limited stitch width.
25
For a narrower stitch, press the " " button (left).
For a wider stitch, press the "+" button (right). The
stitch width can be adjusted between "0.0-7.0".
Certain stitches have a limited stitch width.
When Direct Patterns " ,,,"andAGroup
Pattern " " are selected, the needle position is
regulated by the stitch width adjustment buttons.
Pressing the "" button (left), will move the needle
to the left and pressing the "+" button (right), will
move the needle to the right. The numbers will
be changed from left position "0.0" to extreme
right position "7.0". The pre-set center needle
position will be indicated as "3.5".
Mode selection button
Stitch width
adjustment buttons
Stitch length
adjustment buttons
Elongation button
Mirror button
Twin needle button
26
FUNCTION BUTTONS
FUNCTION BUTTONS
Stitch length adjustment button
When you select a stitch the machine will
automatically set the recommended stitch length
which will be indicated by numbers on the LCD
screen. The stitch length can be adjusted by
pressing the stitch length adjustment buttons.
To shorten the stitch length, press the "" button
(left). For a longer stitch length, press the "+"
button (right). The stitch length can be adjusted
between "0.0-4.5". Certain stitches have a limited
stitch length.
MODE selection button
The LED light will be set at direct mode " " when
you start the machine. By pressing the button,
LED light will move step by step to select the
stitch mode, as shown.
Direct mode stitch selection.
Utility and decorative pattern mode (A group):
Stitch selection using the number buttons.
Decorative pattern mode (B group): Stitch
selection using the number buttons.
Block letter mode: Character selection using
the number buttons.
Script letter mode: Character selection using
the number buttons.
Outline letter mode: Character selection using
the number buttons.
MODE
Elongation button (see page 59)
A Group Patterns 28-51 can be elongated up to
five times its normal length by pressing the " "
button, the LED light will turn on.
When the width or length or stitch is changed, a
greater variety of patterns are available.
27
FUNCTION BUTTONS
FUNCTION BUTTONS
Mirror button (see page 60)
Except the Direct Patterns ",,"andthe
patterns 14-27 from the Group Patterns "A", the
other patterns can be mirror imaged along a
vertical axis by pressing the " " button.
LED light will turn on. The machine will continue
to sew the reflected pattern until the mirror button
is pressed again. The mirror function also will be
canceled if the pattern changed.
The function for mirror imaging the pattern appears
on the LCD screen.
Twin needle button (see page 61)
Except the Direct Patterns ",,"andthe
patterns 14-27 from Group Patterns "A", the other
patterns can be sewn in two parallel line of the
same stitch with the twin needle.
Press the " " button, LED light will turn on, and
the machine automatically reduces the maximum
width for the twin needle sewing. Press the button
again to return to single needle sewing.
SELECTION BUTTONS
SELECTION BUTTONS
Direct pattern selection
and number buttons
Clear button
Edit button
Memory button
Direct pattern selection and number buttons
Direct pattern selection
Press the buttons to select the utility patterns
shown beside the number button when the mode
button is set at the Direct mode.
28
Number buttons
To select the desired pattern and press the
number buttons .
Except the Direct Pattern mode, the other mode
can be selected by pressing the desired numbers.
For example: pattern 44
SELECTION BUTTONS
SELECTION BUTTONS
Press this button when the incorrect character is
selected. Each press of this button erases one
character, or press this button to remove an
added pattern when sewing combinations of
characters or decorative stitches.
Clear button
If you wish to modify any settings in the memory
mode, use the stitch width "+" or "" button to
select the pattern to be modified, and press the
" " button to set the selected pattern under the
editing mode, the LED light will turn on. Manual
setting function of the stitch width, stitch length,
mirror and Auto-lock for these memorized
patterns is now possible. Press the " " button
again to leave the editing mode and return to
memory mode.
123
Edit button
Press the " " button to enter the memory mode,
and store the combinations of characters or
decorative stitches. Use the stitch width "+" or ""
button to confirm the pattern memorized by
pressing this button in memory mode.
Please Note: The Direct mode patterns and
buttonholes cannot be memorized.
Memory button
29
USEFUL SKILLS
USEFUL SKILLS
1. Stop the sewing machine
when you reach a corner.
2. Lower the needle into the
fabric manually or by pressing
the needle up/down button
once.
3. Raise the presser foot.
4. Use the needle as a pivot and
turn the fabric.
5. Lower the presser foot and
resume sewing.
Reverse stitching is used to
secure the threads at the
beginning and at the end of a
seam.
Press the reverse button and
sew 4-5 stitches.
The machine will sew forward
when the button is released.
Free-arm sewing is convenient for sewing tubular areas such as pant hems and cuffs.
Sewing corners
Reverse
Free arm
30
5
1
22
3
4
The black button on the right
side of the presser foot will lock
the presser foot in a horizontal
position if you push it in before
lowering the presser foot. This
ensures even feeding at the
beginning of a seam and helps
when sewing multiple layers of
fabric such as sewing over
seams when hemming jeans.
When you reach the point of an
increased thickness, lower the
needle and raise the presser
foot. Press the toe of the foot
and push in the black button,
then lower the foot and
continue sewing.
The black button releases
automatically after sewing few
stitches.
You also can place another
piece of fabric with the same
thickness at the back of the
seam.
Or support the presser foot
while feeding by hand and
sewing toward the folded side.
USEFUL SKILLS
USEFUL SKILLS
Sewing on the heavy fabric
31
Cardboard or
thick fabric
Changing the needle position
This setting can be apply only to Direct Patterns ",,,
" and pattern " " from Group Patterns "A" .
The pre-set position is "3.5", center position. When you
press the "" stitch width adjustment button, the needle
position will move to the left. When you press the "+"
stitch width adjustment button, the needle position will
move to the right. On the LCD screen, the point
illustration and the number indicate the needle position.
Changing the stitch length
To shorten the stitch length, press the "" stitch length
adjustment button. For a longer stitch length, press the
"+" stitch length adjustment button.
Generally speaking, the thicker the fabric, thread and
needle, the longer the stitch should be.
T
T
Adjusting the stitch width
The maximum zigzag stitch width for zigzag stitching is
"7.0"; however, the width can be reduced on any
patterns. The width increases as you press the "+"
stitch width adjustment button from "0.0-7.0".
Adjusting the stitch length
The density of zigzag stitches increase as the setting
of stitch length approaches "0.2".
Neat zigzag stitches are usually achieved at "1.0-2.5".
Closed up zigzag stitches (close together) are referred
to as a satin stitch.
STRAIGHT STITCHES AND NEEDLE POSITION
STRAIGHT STITCHES AND NEEDLE POSITION
ZIGZAG STITCHES
ZIGZAG STITCHES
32
A
7.05.0
3.0
1.0
4.5
3.0
2.01.00.5
0.0
4.5
3.0
2.01.00.5
0.0 2.0
3.5
5.0 7.0
It assures you of a stitch that is strong and
flexible and will give with the fabric without
breaking. Good for easy to ravel and knit
fabrics. It is good for joining durable fabric
such as denims.
These stitches can also be used as a
decorative top stitch.
Triple zigzag stretch stitch is suitable for
firm fabrics like denim, poplin, duck, etc.
T
Straight stretch stitch is used to add triple
reinforcement to stretch and hardwearing
seams.
33
A
STRETCH STITCH
STRETCH STITCH
Straight stretch stitch
Straight stitch
Using the overcasting foot
1. Change the presser foot to the overcasting foot.
2. Sew the fabric with the fabric edge against the guide of the overcasting foot.
Attention: The overcasting foot should be used to sew with Direct Patterns 5 and 8 only and
do not set the stitch width narrower than "5.0". It is possible that needle could hit the presser
foot and break when sewing other patterns and width.
1. Change the presser foot to the all purpose foot.
2. Sewing the overcasting along the edge of the fabric so that the needle drops over the edge of
the fabric on the right side.
3
34
OVERCASTING STITCHES
OVERCASTING STITCHES
Using the all purpose foot
E
1
3
5.0~7.0
2.0~3.0
T
1
2.5~4.5
2.0~3.0
2
2
1. Fold the fabric as illustrated with the
wrong side uppermost.
2. Place the fabric under the foot. Turn the
handwheel forwards by hand until the
needle swings fully to the left. It should
just pierce the fold of the fabric. If it does
not, adjust the stitch width accordingly.
3. Adjust the guide (b) by turning the knob (a)
so that the guide just rests against the fold.
4. Sew slowly, guiding the fabric carefully
along the edge of the guide.
5. Turn over the fabric.
9 :
03:
04:
Blind hem/ lingerie for firm fabrics
Blind hem for stretch fabrics
Blind hem for stretch fabrics
1
5mm 5mm
Overcasting
stitches
35
Reverse
side
Reverse
side
BLIND HEM/ LINGERIE STITCH
BLIND HEM/ LINGERIE STITCH
a
b
3
5
F
2.5~4.0
1.0~2.0
2
4
Please Note: It takes practice to sew
blind hems. Always make a sewing
test first.
36
1. Select the pattern 25 from the Group
Patterns "A" to get the button sewing stitch.
Change the presser foot to the button
sewing foot.
2.5~4.5
BUTTON SEWING
BUTTON SEWING
1
2. Position the work under the foot. Place the
button in the desired position, lower the
foot.
3. Adjust the stitch width to "2.5-4.5" according
to the distance between the two holes of the
button.
6
2
2.5~4.5
3
4
4. Turn the handwheel to check that the
needle goes cleanly into the left and right
holes of the button.
5. Before sewing, press the Auto-lock button
to sew reinforcement stitches automatically
at the beginning and at the end of the stitch.
If a shank is required, place a darning
needle on top of the button and sew.
6. For buttons with 4 holes, sew through the
front two holes first, push work forward and
then sew through the back two holes.
5
Please Note: Before sewing a buttonhole on your project, practice on a scrap piece of the
same type of fabric.
37
M:
14:
0:
15 :
16:
17:
C:
18:
19:
20:
21:
For thin or medium fabric
For horizontal holes on blouses
or shirts made from thin or
medium fabric
For thin or medium fabric
For horizontal holes on blouses
or shirts made from thin or
medium fabric
For horizontal buttonholes on
thick fabrics
For thin or medium fabric
For suits or overcoats
For thick coats
For jeans or trousers
For jeans or stretch fabric with
a coarse weave
For stretch fabric
BUTTONHOLE STITCHING
BUTTONHOLE STITCHING
D
2.5~7.0
0.3~1.0
3.0~7.0
0.3~1.0
2.5~5.5
0.3~1.0
5.5~7.0
0.3~1.0
3.0~7.0
1.0~2.0
1. Mark the positions of the buttonhole on the
fabric.
The maximum buttonhole length is 3cm (1
3/16 inch). (Total of diameter + thickness of
button.)
2. Attach the buttonhole foot, then pull out the
button holder plate and insert the button.
The size of the buttonhole is determined by
the button inserted in the button plate.
The thread should be passed through the
hole in the presser foot, then be placed
under the foot.
1
2
3.0~7.0
1.0~3.0
3. Select the buttonhole stitch. Adjust the
stitch width and the stitch length to the
desired width and density.
4. Position the fabric under the presser foot
so that the centerline's mark is aligning with
the center of the buttonhole foot.
Lower the buttonhole lever, then push it to
the back.
Please Note: When you select any
buttonhole pattern, theLCD screen will
be demonstrated the
, it is to remind you to
lower the buttonhole lever.
warning animation
message display
BUTTONHOLE STITCHING
BUTTONHOLE STITCHING
PUSH
4
PUSH
5. While lightly holding the end of the upper
thread, start sewing.
Please Note: Gently feed the fabric by
hand. Before stopping, the machine will
automatically sew a reinforcement
stitch after the buttonhole is sewn.
5
PUSH
38
Starting
point
3
NOTE
Make no
gap here
6. Buttonholes are sewn from the front of the
presser foot to the back, as shown.
39
BUTTONHOLE STITCHING
BUTTONHOLE STITCHING
6
7. Raise the presser foot and cut thread. To
sew over same buttonhole, raise the presser
foot (will return to original position). After
sewing the buttonhole stitch, raise the
buttonhole lever until it stops.
7
PU
SH
Please Note: After finishing the
buttonhole stitch, the LCD screen will
be demonstrated the
, it is to remind you to
lift the buttonhole lever.
warning animation
message display
40
BUTTONHOLE STITCHING
BUTTONHOLE STITCHING
8. Cut the center of the buttonhole being
careful not to cut any stitches on either side.
Use a pin as a stopper at the bartack so
you do not cut too much.
8
When sewing buttonholes on stretch fabric, hook heavy thread or cord under the
buttonhole foot.
1. Attach the buttonhole foot and hook the
gimp thread onto the back of the presser
foot. Bring the two gimp thread ends to the
front of the foot and insert them into the
grooves, then temporarily tie them there.
Lower the presser foot and start sewing.
Set the stitch width to match the diameter
of the gimp thread.
2. Once sewing is completed, pull the gimp
thread gently to remove any slack, then
trim off any excess.
Please Note: It is suggested that you use interfacing on the backside of the fabric.
Making a buttonhole on stretch fabrics
2
1
NOTE
Make no
gap here
41
1. Select pattern 22 from the Group Patterns
"A" to get the bar tack stitch. the
presser foot to the buttonhole foot.
Change
BAR TACK STITCH
BAR TACK STITCH
1.0~3.0
0.3~1.0
D
2. Pull the button holder to the rear. Set the
button guide plate on the buttonhole foot to
the desired length.
Starting
point
3
2mm
NOTE
Make no
gap here
3. Position the fabric so that the needle is
2mm (1/16 inch) in front of the pocket
opening, and then lower the presser foot
lever.
PUSH
4
4. Pass the upper thread down through the
hole in the presser foot. Pull down the
buttonhole lever then push it back. The
buttonhole lever is positioned behind the
bracket on the buttonhole foot. Gently hold
the end of the upper thread in your left
hand, and then start sewing.
1 2
5
5. Bar tack stitches are sewn.
6. As an example, the procedure for sewing
bar tacks at pocket corners.
6
42
ADJUSTING PATTERN BALANCE
ADJUSTING PATTERN BALANCE
If the decorative stitch patterns, numbers or manual buttonhole stitch are uneven when
you sew on a particular fabric, adjust them with the feed balancing dial.
The dial should usually be in a neutral position.
ABC
ABC
ABC
Adjusting distorted stretch stitch patterns
A. When Patterns are too compressed, correct
by turning the dial in the direction of "".
B. Correct setting.
C. When Patterns are too drawn out, correct
by turning the dial in the direction of "+".
Adjusting distorted letters or numbers
A. When the letters or numbers ave overlap,
turn the dial to "".
B. Correct setting.
C. When the patterns are too drawn out,
correct by turn the dial to "+".
Adjusting the stitch density for buttonhole
A. Right side is denser. If the left side of the
buttonhole is than the right side,
turn the feed balancing dial to "".
B. Correct setting.
C. Left side is denser. If the right side of the
buttonhole is than the left side,
turn the feed balancing dial to "+".
less dense
less dense
43
EYELET STITCH
EYELET STITCH
1. Select pattern 23 or 24 from the Group
Patterns "A" to get the eyelet stitch. Attach
presser the foot "A".
2. Press the "" or "+" stitch width adjustment
to button select the eyelet size.
Size of eyelet.
A. Large: 7.0mm (1/4 inch).
B. Medium: 6.0mm (15/64 inch).
C. Small: 5.0mm (3/16 inch).
3. Lower the needle into the fabric at the
beginning of the stitching, and then lower
the presser foot lever. Once sewing is
completed, the machine automatically
sews reinforcement stitches, then stops.
4. Make a hole at the center using an eyelet
punch.
* Eyelet punch is not included with the
machine.
Please Note: If thin thread is used, the
stitching may be coarse. If this occurs,
sew the eyelet twice one on top of the
other.
ABC
1
2
3
4
23:
24:
Select for sewing eyelets on belts , etc
Select for sewing eyelets on belts , etc
5.0 6.0 7.0
A
44
1. Select pattern 26 or 27 from the Group
Patterns "A" to get the darning stitch.
Change the presser foot to the buttonhole
foot.
3. Pull the button holder to the rear. Set the
button guide plate on buttonhole foot to the
desired length.
1
2. Baste the upper fabric and the under fabric
together. Select the needle position. Lower
the presser foot over the center of the tear.
3
2
Start
a
b
Stop
4
Stop
a
Start
b
NOTE
Make no
gap here
4. The size of one darn cycle is variable.
However, the maximum stitch length is
2.6cm (1 inch) and the maximum stitch
width is 7mm (9/32 inch).
a. The length of sewing.
b. The width of sewing.
DARNING STITCH
DARNING STITCH
NOTE
Make no
gap here
3.5~7.0
1.0~2.0
D
5. Position the fabric so that the needle is
2mm (1/16 inch) in front of the area to be
darned, and then lower the presser foot
lever.
When lowering the
presser foot, do not push in the front of
the presser foot, otherwise the darning
will not be sewn with the correct size.
Please Note:
6. Pass the upper thread down through the
hole in the presser foot. Pull down the
buttonhole lever then push it back. The
buttonhole lever is positioned behind the
bracket on the buttonhole foot. Gently hold
the end of the upper thread in your left
hand, and then start sewing.
Please Note: When you select any
buttonhole pattern or darning pattern,
LCD screen will be demonstrated the
warning animation message display, it
is to remind you to lower the buttonhole
lever.
8. If the sewing range is too big to sew, then
we suggest you can sew several times (or
cross sew) to get better sewing result.
7
8
2mm
5
7. Darning stitches are sewn from the front of
the presser foot to the back, as shown.
DARNING STITCH
DARNING STITCH
6
PUSH
45
46
1. Baste the zipper opening on the garment.
2. Press open the seam allowance. Place the
zipper face down on the seam allowance
with the teeth against the seam line. Baste
the zipper tape.
3. Attach the zipper foot. Attach the right side
of the presser foot pin to the holder when
sewing the left side of the zipper.
4. Attach the left side of the presser foot pin to
the presser foot holder when sewing the
right side of the zipper.
5. Stitch left side of the zipper from top to
bottom.
6. Stitch across the lower end and right side
of zipper. Remove the basting and press.
I
Inserting a centered zipper
Attention: Zipper foot should be used for
sewing with the centered needle position
straight stitch only. It is possible that the
needle could hit the presser foot and
break when sewing other patterns.
ZIPPER INSERTION
ZIPPER INSERTION
2 inch
1
2
3.5
1.5~3.0
6
3
4
5
Inserting a side zipper
47
1. Baste the zipper opening on the garment.
2. Fold back to the left seam allowance. Turn
under the right seam allowance to form
a 3mm (1/8 inch) fold.
3. Attach the zipper foot. Attach the right side
of the presser foot pin to the holder when
sewing the left side of the zipper. Attach
the left side of the presser foot pin to the
presser foot holder when sewing the right
side of the zipper.
4. Stitch the left side of the zipper from bottom
to top.
5. Turn the fabric right side out, stitch across
the lower end and right side of zipper.
6. Stop about 5cm (2 inches) from the top of
zipper. Remove the basting and open the
zipper. Stitch the remainder of the seam.
ZIPPER INSERTION
ZIPPER INSERTION
2 inch
1
2
5
6
3
4
48
K
1. Fold the edge of the fabric over about 3mm
(1/8 inch), then fold it over again 3mm (1/8
inch) for about 5cm (2 inches) along the
edge of the fabric.
2. Insert the needle into the fold by rotating
the handwheel toward you, and lower the
presser foot. Sew several stitches and
raise the presser foot.
Insert the fabric fold into the spiral opening
of hemmer foot. Move the fabric back and
forth until the fold forms a scroll shape.
3. Lower the presser foot and start sewing
slowly guiding the raw edge of the fabric in
front of the hemmer foot evenly into the
scroll of the foot.
1
NARROW HEMMING
NARROW HEMMING
3.5
1.5~3.0
2
3
49
M
Mark the design on the fabric. Insert the cord
in the center groove of the cording foot from
the right side opening. Pull the cord about
5cm (2 inches) behind the foot.
The grooves under the foot will hold the
length of the cord in place while the stitches
are being form over the cord.
Select the stitch and adjust the stitch width so
that the stitches are just covering the cord.
Lower the foot and sew slowly, guiding the
cord over the design.
Single cording
Sew over one strand of cording to create a pretty swirled design on a jacket or vest or sew over
three strands of cording for border trims. Pearl cotton, knitting yarn, embroidery floss, lace thread,
fine wool or lily yarn can be used for cording.
M
Triple cording
Push the sewing thread to the left and insert
three cords into the grooves of the foot and
pull about 5cm (2 inches) of the cords behind
the foot. Select the desired pattern and adjust
the stitch width so that the stitches are just
covering the cords. Lower the foot and sew
slowly guiding the cords.
CORDING
CORDING
50
A
Use the satin stitch foot for satin stitching and
sewing decorative stitches. This foot has a full
indentation on the underside to allowed easy
sewing over the thickness of the stitches form
by closely spaced zigzag stitches, and even
feeding of the fabric.
To tailor the satin or decorative stitch pattern,
you may adjust the length and width of the
pattern by pressing the stitch length and width
adjustment buttons. Experiment with fabric
scraps until you get the desired length and
width.
Please Note: When sewing very thin
fabrics, it is suggested that you use
interfacing on the backside of the fabric.
SATIN STITCH SEWING
SATIN STITCH SEWING
3.5~7.0
0.5~2.0
05 28 29 30 31 32 33 34 35 36
37 38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55 56
57 58 59 60
51
P
Insert the quilting guide in the presser foot
holder as illustrated and set the space as you
desire.
Sew the first row and move over the fabric to
sew successive rows with the guide riding
along the previous row of stitching.
QUILTING
QUILTING
3.5
1.0~3.0
52
1. Remove the presser foot holder and attach
the gathering foot.
2. Sew a single row or multiple rows of
straight stitches.
3. If more gathering is required, loosen the
upper thread tension to below 2 so that the
bobbin thread lies on the underside of the
material.
4. Pull the bobbin threads to obtain the
desired amount of gather, then tie the
threads to secure them.
5. Smooth the gathers by ironing them.
Please Note: It can also use the all
purpose foot and gather fabric by hand
by lowering the tension setting to below
2 and pulling the lower thread to gather
the material.
GATHERING
GATHERING
3.5
4.5
53
1. Use the gathering foot to sew straight lines
1cm (3/8 inch) apart, across the area to be
smocked.
* For gathering sewing instructions, see
page 52.
2. Knot the threads along one edge. Pull the
bobbin threads and distribute the gathers
evenly. Secure the threads at the other end.
3. Reduce the tension, if necessary and sew
decorative pattern stitches between the
straight seams.
4. Pull out the gathering stitches.
SMOCKING
SMOCKING
4
2
3
1
T
A
54
Remove the presser foot holder, and attach
the darning foot to the presser foot holder bar.
The lever (a) should be behind the needle
clamp screw (b). Press the darning foot on
firmly from behind with your index finger and
tighten the screw (c).
Move the drop feed control to " " to lower
the feed dogs.
First sew around the edges of the hole (to
secure the threads). Working from left to right,
sew over the hole in a constant and
continuous movement. Turn the work by 1/4
and sew over the first stitching moving the
work slower over the hole to separate the
threads and not form big gaps between the
threads.
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING
Darning
a
b
b
aa
3.5~5.0
a
b
c
Please Note: Free motion darning is accomplished without the sewing machine internal
feed system. Movement of the fabric is controlled by the operator. It is necessary to
coordinate sewing speed and movement of fabric.
Select zigzag stitch pattern and adjust the
stitch width as desired. Stitch along the
outline of the design by moving the
embroidery hoop. Make sure to maintain a
constant speed.
Fill in the design working from the outline
towards the inside. Keep the stitches close
together.
You will get longer stitches by moving the
hoop faster and shorter stitches by moving
the hoop more slowly.
Secure with a reinforcement stitches at the
end by pressing the Auto-lock button.
Select the zigzag stitch pattern and adjust the
stitch width as desired. Sew at a constant
speed, moving the hoop slowly along the
lettering.
When the letter is finished. Secure with a
reinforcement stitch at the end by pressing
the Auto-lock button.
* Embroider hoop is not included with the machine.
55
Monogramming
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING
Embroidery
It is easier to guide the fabric and you have a
better view of the seam when using the
standard, regular foot on your machine. Your
sewing machine offers excellent stitch quality
on a wide range of fabrics from delicate
chiffons to multiple layers of denim.
56
WALKING FOOT
WALKING FOOT
2
a
b
c
3
4
Please Note: Always try to sew first without the walking foot
accessory which should be used only when necessary.
The Walking Foot accessory equalizes the
feeding of the upper and lower layers of fabric
and improves the matching of plaids, stripes
and patterns. It also helps to prevent uneven
feeding of very difficult fabrics.
1. Lift the presser foot lifter to raise the
presser foot bar.
2. Remove the presser foot holder by
unscrewing (counterclockwise) the presser
bar attaching screw.
3. Attach the Walking Foot to the machine as
follows:
- The arm (a) should fit into above the
needle screw and clamp (b).
- Slide the plastic attaching head (c) from
your left to right so that it is fitted into the
presser foot bar.
- Lower the presser foot bar.
- Replace and tighten (clockwise) the
presser bar attaching screw.
- Make sure both the needle screw and the
presser bar attaching screw are tightly
secured.
4. Draw the bobbin thread up and place both
the bobbin thread and the needle thread
behind the walking foot attachment.
1
1. Place the two pieces of fabric with the right
side together and sew with the straight
stitch. Open the seam allowances and
presses it flat.
2. Place the center of the presser foot on the
seam line of the joined pieces of fabric and
sew over the seam.
T
1. Separate the folded edges of the fabric
pieces with a gap of 4mm (1/8 inch) and
baste them onto a piece of thin paper or
water-soluble stabilizer sheet.
2. Align the center of the presser foot with the
center of the two pieces of fabric and begin
sewing.
3. After sewing, remove the paper.
57
FAGOTING
FAGOTING
PATCHWORK STITCHING
PATCHWORK STITCHING
3
Thin paper
Basting
1
2
T
A
A
58
T
T
A
1. Fold the fabric right side together in and
sew along the edge.
2. Cut the fabric along the seam leaving an
allowance of 3mm (1/8 inch) for seaming.
Notch the allowance.
3. Turn the fabric over and push out the curved
seam to the surface and iron it.
1. Stitch along the edge of the fabric, marking
sure not to sew directly on the edge of the
fabric.
* For better results, apply spray starch onto
the fabric and press with a hot iron before
it is sewn.
2. Trim along the stitches.
* Be careful not to cut the stitches.
SCALLOP STITCH
Scallop hem
SCALLOP STITCH
Scallop edging
3
2
2
Wrong side
of fabric
1
1
ELONGATION
ELONGATION
A
2.5~7.0
0.3~1.0
59
1. The stitch can be elongated up to five times
its normal length by pressing the elongation
button.
1
3
x5
x4
x3
x2
x1
2
2. The LCD screen icon for elongation imaging
of the pattern appears.
3. When the width or length or stitch is
changed, a greater variety of patterns are
available.
Please Note: A Group Patterns 28-51
can be elongated and mirrored
simultaneously.
MIRROR
MIRROR
60
1. Select the pattern.
1
3
2
3. The LCD screen icon for mirror imaging of
the pattern appears.
2. Pressing the mirror button.
Please Note:
- Direct Patterns ",,"andPatterns 14-27 from Group Patterns "A" cannot be
mirror imaged.
- Mirror imaged patterns can also be combined with other patterns.
4
A. Normal pattern sewing.
B. Mirror pattern sewing.
A
B
61
1. Insert the twin needle.
T
2. Follow the instructions for single-needle
threading using the horizontal spool pin.
Thread through the left needle.
Set the second spool pin (included with the
accessories) into the hole on the top of the
machine. Thread through remaining points,
making certain to omit the thread guide
above the needle and pass thread through
the right needle.
3. Thread each needle separately.
Please Note: Make sure that the two
threads used to thread the twin needle
are of the same weight. You can use
one or two colors.
1.0~3.0
1
USING THE TWIN NEEDLE
USING THE TWIN NEEDLE
Please Note: When using twin needles, use the "T" presser
foot regardless of what kind of sewing will be carried out.
Attention: Use only the twin needle type
included (part code: 006020008). Use of
any other twin needle type may result in the
needle being bent or damage to the
machine.
Never use bent needles. Bent
needles can easily break, possibly
resulting in injuries.
3
Please Note: When sewing with twin
needle, always proceed slowly, and
make sure to maintain a low speed to
insure quality stitching.
4. Press the Twin needle button, the LED light
will turn on, and the machine automatically
reduces the maximum width for twin needle
sewing.
5. Select a stitch pattern and start to sew.
Except the Direct Patterns " , , " and
patterns 14-27 from the Group Patterns "A",
the other patterns can be used.
Two lines of stitching are sewn parallel to
each other.
4
5
2
MEMORY
MEMORY
62
Please Note:
- Multiple patterns selecting from pattern modes ,,,,canbecombined and
sewn together.
- Direct Patterns and patterns 14-27 from Group Patterns "A" cannot be entered into
memory.
- This machine has 4 modules of program memory and each module can retain 20 units of
stitches.
- All the units in the memory can be edited to set its function such as Stitch length, Stitch
width, Elongation, Mirror, and Auto-lock.
Combining patterns or letters
1. Press the "MODE" button to select any desired pattern
group among , , , , on front cover.
The LED will indicate the selected group.
2. Press the " " button to open the memory mode and then
appears a sub-screen in the center. It is available to select
the number of the memory module when the cursor start
flashing.
4. Enter the memory screen automatically and the flashing
cursor stays in the first position.
3. Press the number of the memory module. (e.g. 2)
2
4
3
Combined patterns can be stored for later use. Since stored patterns are not lost after the
sewing machine is turned off, they can be recalled at any time. This is convenient for
patterns, such as names, that will be used often.
MODE
1
MEMORY
MEMORY
63
6
7
6. The selected pattern displays on the LCD screen and the
cursor move to the next position.
7. Repeat step 5, 6 for more patterns to be stored in the
memory.
Please Note: When the memory the full with 20 units of
patterns, the machine will beep to signal it.
5. Press the desired pattern number. (e.g. 18)
5
8
8. Press the " " button to leave the memory mode and return
to the normal screen.
Attention:
The selected pattern will be cleared from the
memory module after closing the machine if you do not
press the " " button again when you have completed
your selection.
7
1. Press the stitch width adjustment button and shift the cursor
past the last pattern or letter where you would like to add
another pattern while in the memory mode.
1
Adding patterns or letters
2. Press pattern number. (e.g. 31) The selected pattern will be
inserted.
2
MEMORY
MEMORY
64
Editing patterns
1. Use the stitch width adjustment button to select the pattern
that you wish to edit while in the memory mode.
2. Press the " " button to edit the pattern. The stitch length,
stitch width, Elongation, Mirror imaging and Auto-lock of the
patterns can be adjusted manually.
4. Press the " " button when complete and return to browse
status.
Please Note: The stitch length, stitch width, Elongation,
Mirror, and Auto-lock of the patterns can be adjusted
manually.
1. Use the stitch width adjustment button to select the pattern
that you want to clear while in the memory mode.
2. Press the " " button to delete the selected pattern and the
next pattern in the back will move forward.
Clearing patterns or letters
1
2
3
4
1
2
MEMORY
MEMORY
65
5. The cursor on the LCD screen will move along with the
sequential pattern while sewing.
6. Press the " " button to leave memory mode and return to
the normal screen.
1. Press the " " button to enter the memory mode and then
input the number of the memory module when the cursor
start flashing.
2. Input the number of the memory module. (e.g. 2)
3. The LCD screen containing the various types of stitches will
open.
Recalling and sewing the memorized pattern
6
1
2
4. Press on the foot control or press the Start/stop button to
start the sewing machine.
4
Please Note: If the cursor stays in a vacant position in
the end, the machine will start sewing from the first
pattern. If the cursor stays under a specific pattern, the
machine will start sewing from that pattern.
3
5
WARNING FUNCTIONS
WARNING FUNCTIONS
66
Warning animation message display
Presser foot is not lowered
The Start/stop button or reverse button was pressed
while the presser foot was raise.
BH lever is not lowered
The buttonhole or darning stitch was selected and the
start/stop button was pressed while the buttonhole lever
is raised.
BH lever is not lifted
A stitch other than the buttonhole or darning stitch was
selected and the start/stop button was pressed while the
buttonhole lever is down.
The sewing machine is in trouble
The animation message means that the thread is twisted
or jammed and the hand wheel axle cannot move.
Please look through the "Trouble shooting guide" on
page 72/73 to find the solution. After the problem has
been solved, the machine will continue to sew.
Return bobbin winder stopper to right
When the bobbin winder stopper is in left, press any
button (expect the Start/stop button), the LCD screen will
display the animation of return bobbin winder stopper to
right.
WARNING FUNCTIONS
WARNING FUNCTIONS
67
- When operating correctly: 1 beep
- When the memory is full with 20 units of pattern: 2-short beeps
- When operating incorrectly: 3-short beeps
- When the sewing machine is in trouble and can't sew: 8 seconds short beeps
It means that the thread is twisted or jammed and the hand wheel axle can't move. Please look
through the "Trouble shooting guide" on page 72/73 to find the solution. After the problem has
been solved, the machine will continue to sew.
Warning beeping sound
Please Note: If the problem is still not solved, please contact your local dealer.
Attention: During the sewing, if the thread get jammed inside the hook stopping the
needle from moving and you continue pressing the foot control, the security switch will
stop the machine completely. In order to restart the sewing machine, you will have to
turn the on/off switch to the OFF position and then ON again.
Instruction animation message display
Bobbin winding
The bobbin winder is winding the bobbin.
BUZZER SOUND
BUZZER SOUND
3. Pressing the " " button. The buzzer
sound setting mark will appear on the LCD
screen when you have set it.
1
1. Press on the " " button and turn on the
power switch.
2. You can select the mode by pressing the
stitch width "+" or "" button.
Select desired mode sound on " " or sound
off " ".
ONOFF
68
2
3
69
Attention: Turn the power switch off and wait until the lamp has cooled down before
touching it.
1. Loosen the screw (a) on the left side of the
sewing head and remove the face plate (b).
2. If the machine is equipped with a 5W lamp,
replace the bulb as follows:
Pull light bulb downward to remove.
Replace the bulb with same type rated 5W.
Replace the face plate and tighten the
screw.
REPLACING THE LIGHT BULB
REPLACING THE LIGHT BULB
1
a
b
Please Note:
-
-
The 5W lamp is user-replaceable.
The 240mW LED lamp is not user-replaceable.
3
2
PUSH
3. If the machine is equipped with a 240mW
LED lamp, you must contact the manufacturer
or its service agent for repair in the event of
failure.
70
Attention: Disconnect the power cord from the wall socket before cleaning the screen and
sewing machine surface, otherwise injury or electrical shock may result.
If the front panel is dirty, wipe it gently with a
soft, dry cloth.
Do not use any organic solvents or detergents.
If the surface of the sewing machine is dirty, lightly soak a cloth in mild detergent, squeeze it out
firmly and then wipe the surface. After cleaning it once in this way, wipe the surface again with a
dry cloth.
MAINTENANCE
MAINTENANCE
Cleaning the screen
Cleaning the sewing machine surface
Attention: Disconnect the machine from the wall outlet before carrying out any maintenance.
Cleaning the hook
If lint and bits of thread accumulate in the hook, this will interfere with the smooth operation of the
machine. Check regularly and clean the stitching mechanism when necessary.
1
2
1. Remove the bobbin cover plate and bobbin.
2. Clean the bobbin holder with a brush.
71
MAINTENANCE
MAINTENANCE
3
4
3. Remove the needle, presser foot and
presser foot holder. Remove the bobbin
cover plate and bobbin. Remove the screw
holding the needle plate and remove the
needle plate.
4. Lift up the bobbin case and remove it.
5
a
b
6
5. Clean the hook race, feed dog and bobbin
case with a brush. Also clean them, using a
soft, dry cloth.
6. Replace the bobbin case into the hook race
so that the tip (a) fits to the stopper (b) as
shown.
72
Before calling for service, check the following items. If the problem still persists, contact the place of
purchase or your nearest authorized dealer.
TROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE
Problem
Cause
Correction
Upper thread
breaks
Lower thread
breaks
Skipped
stitches
Needle
breaks
Loose
stitches
Seam
gather or
pucker
1.The machine is not threaded correctly.
2.The thread tension is too tight.
3.The thread is too thick for the needle.
4.The needle is not inserted correctly.
5.The thread is wound around the spool
holder pin.
6.The needle is damaged.
1.The bobbin case is not inserted
correctly.
2.The bobbin case is threaded wrong.
3.The lower thread tension is too tight
1.The needle is not inserted correctly.
2.The needle is damaged.
3.The wrong size needle has been used.
4.The foot is not attached correctly.
5.The machine is not threaded correctly.
6.The presser foot pressure is not strong
enough.
1.The needle is damaged.
2.The needle is not correctly inserted.
3.Wrong needle size for the fabric.
4.The wrong foot is attached.
5.The needle clamp screw is loose.
6.The presser foot that is used is not
appropriate for the type of stitch that
you wish to sew.
7.The upper thread tension is too tight.
1.The machine is not correctly threaded.
2.The bobbin case is not correctly
threaded.
3.Needle/fabric/thread combination is
wrong.
4.Thread tension is wrong.
1.The needle is too thick for the fabric.
2.The stitch length is adjusted wrong.
3.The thread tension is too tight.
1.Select a finer needle.
2.Readjust the stitch length.
3.Loosen the thread tension.
1.Check the threading.
2.Thread the bobbin case as illustrated.
3.The needle size must suit the fabric
and thread.
4.Correct the thread tension.
1.Insert a new needle.
2.Insert the needle correctly (flat side
towards the back).
3.Choose a needle to suit the thread and
fabric.
4.Select the correct foot.
5.Use the screwdriver to firmly tighten
the screw.
6.Attach the presser foot that is appro-
priate for the type of stitch that you
wish to sew.
7.Loosen the upper thread tension.
1.Remove and reinsert needle(flat side
towards the back).
2.Insert a new needle.
3.Choose a needle to suit the thread.
4.Check and attach correctly.
5.Rethread the machine.
6.Adjusting the presser foot pressure.
1.Remove and reinsert the bobbin case
and pull on the thread. The thread
should pull easily.
2.Check both bobbin and bobbin case.
3.Loosen lower thread tension as
described.
1.Rethread the machine.
2.Reduce the thread tension (lower
number).
3.Select a larger needle.
4.Remove and reinsert the needle (flat
side towards the back).
5.Remove the reel and wind thread onto
reel.
6.Replace the needle.
Reference
Page 17
Page 20
Page 12
Page 11
Page 17
Page 11
Page 16
Page 12
Page 16
Page 20
Page 11
Page 11
Page 11
Page 74
Page 17
Page 10
Page 11
Page 74
Page 12
Page 16
Page 74
Page 20
Page 17
Page 26
Page 12
Page 20
Page 12
Page 20
Page 11
73
TROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE
Seam
puckering
Patterns are
distorted
1.The needle thread tension is too tight.
2.The needle thread is not threaded
correctly.
3.The needle is too heavy for the fabric
being sewn.
4.The stitch length is too long for the
fabric.
5.The presser foot pressure is not
correctly adjusted.
1.The correct presser foot is not used.
2.The needle thread tension is too tight.
3.The stitch length is not suitable for the
fabric being sewn.
4.Feed balancing dial is not set properly.
1.Select the correct foot.
2.Loosen the thread tension .
3.Make stitch adjust.
4.Adjusting pattern balance.
1.Lossen the thread tension.
2.Rethread the machine.
3.Choose a needle to suit the thread and
fabric.
4.Make stitch dense.
5.Adjusting the presser foot pressure.
The sewing
machine
doesn't
operate
1.The machine is not turned on.
2.The Start/stop button was not pressed.
3.The presser foot lever is raised.
4.The Start/stop button was pressed,
even through the foot controller is
connected.
5.A thread is caught in the hook race.
1.Turn on the machine.
2.Press the Start/stop button.
3.Lower the presser foot lever.
4.Do not use Start/stop button when the
foot controller is con-nected. To use
Start/stop button, disconnect the foot
controller.
5.Remove the upper thread and bobbin
case, turn the handwheel backwards
and forwards by hand and remove the
thread remands.
The
machine
jams
Remove the upper thread and bobbin
case, turn the handwheel backwards
and forwards by hand and remove the
thread remands.
The
machine is
noisy
1.Fluff or oil have collected on the hook
or needle bar.
2.The needle is damaged.
1.Clean the hook and feed dog as
described.
2.Replace the needle.
Uneven
stitches,
uneven feed
1.Poor quality thread.
2.The bobbin case is threaded wrong.
3.Fabric has been pulled.
1.Select a better quality thread.
2.Remove the bobbin case, the thread
and reinsert correctly.
3.Do not pull on the fabric while sewing,
let it be taken up by the machine.
Problem
Cause
Correction Reference
4.Thread is caught in the hook.
3.Slight humming sound coming from
internal motor.
3.Normal
5.The feed dogs are packed with lint.
Remove the upper thread and bobbin
case, turn the handwheel backwards
and forwards by hand and remove the
thread remands.
1.Thread is caught in the hook.
2.The feed dogs are packed with lint.
6.Connect the power line plug to the
electric outlet.
6.The machine is not plugged in.
Page 20
Page 17
Page 12
Page 26
Page 74
Page 20
Page 26
Page 42
Page 70
Page 16
Page 11
--
Page 70
Page 12
Page 8
--
Page 23
Page 22
Page 23
Page 71
Page 8
Page 70
Page 10
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
3.5
1.0
5.0
3.5
3.5
3.5
5.0
5.0
5.0
7.0
5.0
5.0
7.0
7.0
5.5
6.0
5.0
5.0
7.0
7.0
6.0
6.0
0.0~7.0
1.0~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
3.0~7.0
3.0~7.0
2.5~5.5
2.5~5.5
5.5~7.0
5.5~7.0
3.0~7.0
3.0~7.0
2.5
2.5
2.5
1.0
1.0
2.5
2.5
3.0
2.5
2.5
2.5
2.0
2.5
2.5
0.5
0.5
0.5
0.5
0.5
0.5
1.0
1.5
1.5~3.0
1.0~3.0
1.0~3.0
0.5~4.5
0.5~4.5
1.5~3.0
1.5~3.0
2.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~4.5
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
1.0~2.0
1.0~3.0
T
T
T
F
F
T
A
A
T(A)
A
A(M)
A(M)
T
A(T)
D
D
D
D
D
D
D
D
QUICK ADJUSTMENT REFERENCE CHART
QUICK ADJUSTMENT REFERENCE CHART
Direct patterns-12
Functions
Presser
Foot
Stitch Pattern
Auto Manual Auto Manual
Auto-lock Elongation
Mirror/
Presser foot
Twin needle
Reverse
Width (mm) Length (mm)
Memory
/T
/T
/T
/T
/T
/T
/T
/T
/T
1
2
3
4
5
6
7
8
9
0
M
C
3.5
0.0
3.5
3.5
5.0
5.0
5.0
5.0
3.5
5.0
5.0
7.0
0.0~7.0
0.0~7.0
0.0~7.0
1.0~6.0
0.0~7.0
2.0~7.0
2.5~7.0
3.5~7.0
2.5~7.0
2.5~5.5
2.5~7.0
5.5~7.0
2.5
2.5
2.5
2.5
2.0
1.0
2.5
2.5
2.0
0.5
0.5
0.5
0.0~4.5
0.0~4.5
1.0~3.0
1.0~3.0
0.3~4.5
0.3~4.5
1.0~3.0
1.0~3.0
0.5~4.5
0.3~1.0
0.3~1.0
0.3~1.0
T(P/K/I)
T(P/K/I)
T(P)
T
T(E)
T
T(A)
E
F
D
D
D
: Adjustments can be made.
Utility
stitches
A group patterns-100
74
Functions
Presser
Foot
Stitch Pattern
Auto Manual Auto Manual
Auto-lock Elongation
Mirror/
Presser foot
Twin needle
Reverse
Width (mm) Length (mm)
Memory
/A
/T
/A
/A
/A
/A
/T
/A
/T
/T
/T
/T
/T
/T
Utility
stitches
Buttonhole
stitches
QUICK ADJUSTMENT REFERENCE CHART
QUICK ADJUSTMENT REFERENCE CHART
75
Functions
Presser
Foot
Stitch Pattern
Auto Manual Auto Manual
Auto-lock Elongation
Mirror/
Presser foot
Twin needle
Reverse
Width (mm) Length (mm)
Memory
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
2.0
7.0
7.0
3.5
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
5.0
6.0
1.0~3.0
7.0,6.0,5.0
7.0,6.0,5.0
2.5~4.5
3.5~7.0
3.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
4.0~7.0
2.5~7.0
2.5~7.0
4.0~7.0
4.0~7.0
5.0~7.0
2.5~7.0
5.0~7.0
0.5
2.0
2.0
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
1.0
1.5
1.5
1.0
2.0
2.0
1.5
2.5
1.0
0.5~1.0
1.0~2.0
1.0~2.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
0.3~1.0
1.0~2.0
1.5~3.0
1.5~3.0
0.5~2.0
2.0~3.0
2.0~3.0
1.5~3.0
1.0~3.0
1.0~3.0
D
A
A
D
D
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A(T)
Cross
stitches
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
Buttonhole
stitches
Satin
stitches
Darning
stitches
/A
QUICK ADJUSTMENT REFERENCE CHART
QUICK ADJUSTMENT REFERENCE CHART
76
Functions
Presser
Foot
Stitch Pattern
Auto Manual Auto Manual
Auto-lock Elongation
Mirror/
Presser foot
Twin needle
Reverse
Width (mm) Length (mm)
Memory
/A
/A
/A
/A
/A
/A
/A
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
6.0
4.0
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
4.5
5.0
5.0
5.0
5.0
5.0
4.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.5
4.5
5.0
5.0
5.0
5.0
5.0
4.5
7.0
7.0
5.0~7.0
3.0~7.0
3.0~7.0
3.0~7.0
3.0~7.0
3.0~7.0
3.0~7.0
3.0~7.0
3.0~7.0
3.0~7.0
5.0~7.0
3.0~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
4.0~7.0
3.5~7.0
2.5~7.0
4.0~7.0
4.0~7.0
2.5~7.0
2.5~7.0
3.5~7.0
4.5~7.0
3.0~7.0
4.0~7.0
2.5~7.0
2.5~7.0
3.5~7.0
3.0~7.0
4.0~7.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.0
1.0
1.0
1.0
1.5
1.5
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.5
2.0
2.5
1.5
2.0
1.5
1.5
2.0
1.0
2.0
1.5
2.5
2.5
1.0
2.0
2.5
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.5~3.0
1.5~3.0
1.0~3.0
1.5~3.0
1.5~3.0
1.0~3.0
1.0~3.0
1.5~3.0
1.0~3.0
2.0~3.0
1.0~3.0
1.0~3.0
1.5~3.0
1.0~3.0
1.0~3.0
1.5~3.0
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A(T)
A
A(T)
A(T)
A
A
A
A
A
A
A
A
A
A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
: Adjustments can be made.
Cross
stitches
Decorative
stitches
/A
/A
/A
/A
/A
/A
QUICK ADJUSTMENT REFERENCE CHART
QUICK ADJUSTMENT REFERENCE CHART
77
B group patterns-100
Functions
Presser
Foot
Stitch Pattern
Auto Manual Auto Manual
Auto-lock Elongation
Mirror/
Presser foot
Twin needle
Reverse
Width (mm) Length (mm)
Memory
/A
/A
/A
/A
/A
/A
/A
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
5.0
7.0
5.0
7.0
7.0
7.0
7.0
5.0
6.0
5.0
6.0
7.0
7.0
5.0
7.0
7.0
7.0
5.0
5.0
5.0
7.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.0
7.0
7.0
5.0
7.0
6.0
6.0
7.0
7.0
7.0
3.0~7.0
5.0~7.0
4.5~7.0
5.0~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
4.5~7.0
2.5~7.0
3.5~7.0
3.5~7.0
3.5~7.0
2.5~7.0
4.0~7.0
6.0~7.0
6.0~7.0
2.5~7.0
2.5~7.0
3.5~7.0
6.0~7.0
3.5~7.0
3.0~7.0
2.5~7.0
2.5~7.0
2.5~7.0
3.5~7.0
3.0~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
2.5~7.0
3.5~7.0
4.0~7.0
2.5~7.0
2.5~7.0
3.0~7.0
2.5~7.0
2.5
3.5
2.0
1.5
2.0
2.5
2.5
2.5
2.0
2.5
1.5
2.5
2.0
2.0
3.0
3.0
3.0
2.0
1.0
1.0
3.0
2.0
1.5
1.5
2.0
1.0
2.0
2.5
2.0
1.5
2.0
3.0
1.5
2.0
2.0
2.0
3.0
3.0
2.5
1.5~4.5
2.0~4.5
1.5~3.0
1.5~3.0
1.0~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.5~3.0
2.0~3.0
1.0~3.0
2.0~3.0
2.0~3.0
2.0~3.0
2.0~3.0
1.5~3.0
1.0~4.5
1.0~3.0
2.0~3.0
2.0~3.0
1.5~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.0~3.0
1.0~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.5~3.0
2.0~3.0
1.5~3.0
A
A
A
A
T(A)
T(A)
T(A)
T(A)
T(A)
T(A)
A
A
A(T)
A(T)
A(T)
A(T)
A(T)
T
T
A(T)
T
T
T
T
T
T
T
T
T
A(T)
A
A
A
A
A
A
A
A(T)
A(T)
/A
/T
/T
/T
/T
/T
/T
/T
/T
/T
/A
/T
/T
/A
/A
/A
/A
/A
/A
/T
/T
/T
/T
/A
Decorative
stitches
/T
/T
/A
/A
/A
/A
/A
/A
QUICK ADJUSTMENT REFERENCE CHART
QUICK ADJUSTMENT REFERENCE CHART
78
Functions
Presser
Foot
Stitch Pattern
Auto Manual Auto Manual
Auto-lock Elongation
Mirror/
Presser foot
Twin needle
Reverse
Width (mm) Length (mm)
Memory
/A
/A
/A
/A
/A
/A
/A
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
5.0
7.0
7.0
6.0
7.0
7.0
7.0
7.0
7.0
3.5~7.0
3.5~7.0
3.0~7.0
2.5~7.0
3.0~7.0
3.5~7.0
5.0~7.0
5.0~7.0
3.0~7.0
3.0~7.0
5.0~7.0
6.0~7.0
4.0~7.0
4.5~7.0
3.5~7.0
3.0~7.0
3.0~7.0
3.0~7.0
2.5~7.0
4.5~7.0
4.5~7.0
4.0~7.0
3.0~7.0
3.0~7.0
3.5~7.0
3.5~7.0
3.5~7.0
3.5~7.0
3.5~7.0
3.5~7.0
2.5~7.0
3.5~7.0
2.5~7.0
3.5~7.0
4.5~7.0
4.0~7.0
2.5~7.0
3.5~7.0
5.0~7.0
4.5~7.0
2.5
2.0
2.5
2.0
2.5
1.5
2.5
2.0
2.0
2.0
2.5
3.0
3.0
2.0
1.5
3.0
2.0
2.0
2.0
1.5
2.0
2.0
2.0
2.0
2.0
2.0
2.0
1.5
1.5
2.0
1.5
1.0
2.0
2.0
1.0
2.0
2.0
2.0
2.0
2.5
1.5~3.0
1.5~3.0
1.0~3.0
1.5~3.0
1.0~3.0
1.0~3.0
2.0~3.0
2.0~3.0
1.5~3.0
1.5~3.0
2.0~3.0
2.0~3.0
2.5~4.5
2.0~3.0
1.5~3.0
2.0~3.0
1.5~3.0
2.0~3.0
1.0~3.0
1.0~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.0~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.5~3.0
1.0~3.0
1.0~3.0
1.0~3.0
1.5~3.0
1.0~3.0
1.5~3.0
1.5~3.0
1.5~3.0
2.0~3.0
1.5~3.0
A(T)
A(T)
A(T)
A(T)
A(T)
A(T)
A
A(T)
A(T)
A
A
A
A
A
A
A
A(T)
A
A
A
A
A
A
A
A
A
A
A
A
A
A(T)
A(T)
A
A
A
A
A
A(T)
A(T)
A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
Decorative
stitches
/A
/A
/A
/A
/A
/A
/A
/A
/A
QUICK ADJUSTMENT REFERENCE CHART
QUICK ADJUSTMENT REFERENCE CHART
79
Functions
Presser
Foot
Stitch Pattern
Auto Manual Auto Manual
Auto-lock Elongation
Mirror/
Presser foot
Twin needle
Reverse
Width (mm) Length (mm)
Memory
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
7.0
7.0
7.0
7.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.0
5.0
5.0
5.0
5.0
7.0
5.0
5.0
5.0
5.0
4.0~7.0
3.5~7.0
3.0~7.0
4.0~7.0
2.5~7.0
2.5~7.0
4.0~7.0
2.5~7.0
3.5~7.0
4.5~7.0
3.5~7.0
5.0~7.0
5.0~7.0
2.5~7.0
2.5~7.0
4.5~7.0
2.5~7.0
3.5~7.0
3.5~7.0
3.5~7.0
3.0~7.0
2.5
2.5
2.5
3.0
2.0
2.0
2.0
2.5
2.0
2.0
3.0
3.0
2.0
3.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0~3.0
1.5~3.0
1.5~3.0
2.0~3.0
1.0~3.0
1.0~3.0
1.5~3.0
2.0~3.0
1.5~3.0
2.0~3.0
1.5~3.0
2.0~3.0
2.0~3.0
1.5~3.0
1.5~3.0
2.0~3.0
1.5~3.0
1.5~3.0
1.0~3.0
2.0~3.0
1.0~3.0
A
A
A
A(T)
A(T)
A(T)
A(T)
A(T)
A
A
A(T)
A(T)
A(T)
A
A
A
A
A
A(T)
A
A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
Decorative
stitches
/A
/A
/A
/A
/A
/A
: Adjustments can be made.
021D3B0104(B)( ) Dec/10
9000B4
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Silver 9500E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Silver 9500E in de taal/talen: Engels als bijlage per email.

De handleiding is 2,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info