EC Declaration of Conformity..................................................................p.22
6
1. Before You Start
Before using Silk’n™ for the first time, please read this User Manual in its entirety. Pay particular attention to sections on device use procedures, device
operation, and after-use procedures.
We recommend you re-familiarize yourself with this User Manual before each use of Silk’n™.
1.1 What is Silk’n™?
Silk’n™ is a light-based device for long-term hair removal designed for home-use.
1.2. Silk’n™ intended use
Silk’n™ is a personal-use device intended for the removal of unwanted hair. Silk’n™ can be used by individuals with light skin tones (Fitz-Patrick skin types I-IV) and
brown – black hairs. Body areas typical for Silk’n™ use include the arms, legs, bikini line and under arms.
2. Safety with Silk’n
TM
2.1. With Silk’n™ Safety Comes First
HPL™ technology in Silk’n™ - Superior safety with lower energy level
Home Pulsed Light™ technology is able to achieve long-term hair removal results
at a fraction of the energy level used in other light-based hair removal equipment. The low energy used in Silk’n™ reduces its potential to cause harm
or complications, and contributes to your overall safety.
Silk’n™ protects your eyes
The Silk’n™ APPLICATOR has a built-in safety feature for eye protection. It has been designed so that a light pulse can not be emitted when the APPLICATOR
is facing open air. The safety switch is activated only when the APPLICATOR T IP is in full contact with the tissue and pressed.
Silk’n™ protects your skin
The 2X3cm² OPTICAL LENS through which pulses of light are delivered is recessed inside the LAMP CARTRIDGE at the APPLICATOR T IP. This enables Silk’n™ to
protect your skin by avoiding direct contact between the OPTICALLENS and the skin.
Silk’n™ is a powerful electrical device. As such, it should be used with special attention to safety.
Please read all warnings and safety precautions before use, and strictly follow them when using Silk’n™
2.2. Is Silk’n™ for you?
Important Safety Information – Read Before Use!
Silk’n™ is not designed for everyone. Please read and consider the information in the following section in order to decide whether it’s suitable for you.
For further information and personalized advice you may also visit www.silkn.com or your local Silk’n™ domain. If you are unsure if Silk’n™ is safe for you
to use, please ask your doctor or dermatologist!
DO NOT USE Silk’n™ on naturally dark skin complexion!
7
Treating dark skin with Silk’n™ can result in adverse effects such as burns, blisters, and skin color changes (hyper- or hypo-pigmentation).
Silk’n™ removes unwanted hair by selectively addressing hair pigment. Varied quantities of pigment also exist in the surrounding tissue of
skin. The quantity of pigment in a particular person’s skin, which is manifested by their skin complexion, determines the degree of risk they
are exposed to using Silk’n™.
DO NOT USE Silk’n™ on naturally dark skin!
See skin color table on the inside of the cover
DO NOT USE Silk’n™
on tanned skin or after recent sun exposure!
Tanned skin particularly following sun exposure, contains large quantities of the pigment Melanin. This applies to all skin types and
complexions, including those which don’t seem to tan quickly. The presence of large quantities of Melanin exposes the skin to higher risk
when using Silk’n™.
Using Silk’n™ on skin that has been recently exposed to sunlight can result in adverse effects such as burns, blisters, and skin color changes (hyper- or
hypo-pigmentation).
Using Silk’n™ to remove facial hair may cause serious eye injury and may stimulate facial hair growth.
DO NOT USE Silk’n™ on tanned skin or after recent sun exposure! Such use can cause serious
burns or skin injury.
Avoid exposure to the sun for 4 weeks before your Silk’n™ treatment!
Silk’n™ is not recommended for use on the face or neck
Unlike body hair, most of women’s potential facial hair remains inactive and hidden, while only a fraction of it grows and surfaces. Exposing
facial hair to the light pulses of Silk’n™ may remove apparent hair but simultaneously stimulate unwanted growth of hidden hair
Silk’n™ is not recommended for use on the face or neck.
8
2.4. Precautions – How to use Silk’n™ Safely
Choose your energy levels CAREFULLY!
Energy level refers to the intensity of the light pulse that is projected on your skin during use, from the lowest level (-) to the highest
level (+). INDICATOR LIGHTS on the CONTROL PANEL illustrate the energy level at which the machine is set. As the energy level increases, so do the
results of Silk’n™ as well as the risk of side effects (see “Possible Side Effects” below).
Always begin your first use of Silk’n™ at the lowest energy setting (one light at “-“)!
Only if you experience little or no discomfort during and after use of Silk’n™ at the lowest energy setting, raise the energy level by one INDICATOR
LIGHT the next time you use Silk’n™, and so on for each subsequent hair removal session.
For detailed instructions on energy level setting see “Energy Level” box in section 4.4 - “Treating with Silk’n™ for the first time”.
If you have a disease related to photosensitivity, such as porphyria, polymorphic light eruption, solar urticaria, lupus, etc.
If you have a history of skin cancer or areas of potential skin malignancies.
If you have received radiation therapy or chemotherapy treatments within the past 3 months.
If you have any other condition which in your physician’s opinion would make it unsafe for you to be treated.
If you are unsure if Silk’n™ is safe for you to use, please consult with your doctor or dermatologist.
2.3. When to avoid using Silk’n™?
Certain conditions may prevent the use of Silk’n™ temporarily. DO NOT USE Silk’n™ if any of the following currently apply to you:
If you are pregnant or nursing (lactating).
If you were exposed to strong sunlight or an artificial tanning machine during the past 28 days.
If you have a tattoo or permanent makeup on the area to be treated.
If you have dark brown or black spots, such as large freckles, birth marks, moles or warts on the area to be treated.
If you have eczema, psoriasis, lesions, open wounds or active infections, such as cold sore in the area to be treated. Wait for the effected area to
heal before using Silk’n™.
If you have a history of kelodial scar formation, a known sensitivity to light (photosensitivity) or are taking medication that makes the skin more
sensitive to light, including non-steroidal anti-inflammatory agents, (e.g., aspirins, ibuprofens, acetaminophen), tetracyclines, phenothiazines, thiazide,
If you have abnormal skin conditions caused by diabetes, for example, or other systemic or metabolic diseases
If you are currently or have recently been treated with Alpha-Hydroxi Acids (AHAs), Beta-Hydroxi Acids (BHAs), Retin-A®, topical retinoids or
azelaic acid.
If you have been treated with Accutane® (isotretinoin) within the past 6 months.
If you have been on a steroid regimen within the past 3 months.
If you have a histor y of herpes outbreaks in the area of treatment, unless you have consulted your physician and received preventative treatment before using Silk’n™.
If you suffer from epilepsy.
If you have an active implant, such as a pacemaker, incontinence device, insulin pump, etc.
The Silk’n™ device is not effective on naturally white, grey, blond and red body hair. If your body hair is of these colors, Silk’n™ will not work on you.
NOTE! Silk’n™ is not effective on light hair
9
Avoid adverse effects!
Do not treat the same area of skin more than once per hair removal session!
Try to avoid overlapping pulses!
If your skin blisters or burns, STOP USE IMMEDIATELY!
Avoid complications after use of Silk’n™!
Do not expose treated areas of skin to the sun. Be sure to carefully protect the treated skin with sunscreen, throughout the hair removal period
and for at least 2 weeks following the last hair removal session.
Always shave the area to be treated and make sure that the skin is clean and dry before using the Silk’n™.
Cover birthmarks and tattoos before Silk’n™ application.
Cover dark brown or black spots, such as large freckles, birth marks, moles or warts before Silk’n™ application.
Never look directly at the light coming from the Silk’n™ A
PPLICATORand LAMP CARTRIDGE.
Do not use Silk’n™ on nipples and genitals (male or female).
Do not use Silk’n™ on any body site where you might later want hair.
Do not use Silk’n™ for any purpose other than hair removal.
Never point the Silk’n™ APPLICATORin an attempt to emit a light pulse into open space. Always make sure that the APPLICATOR is pointed at, and in
full contact with the skin during application.
Remove the Silk’n™ APPLICATOR from the skin if either the skin or the APPLICATOR is too hot.
Never use flammable liquids such as alcohol (including perfumes, sanitizers, or other applications containing alcohol) or acetone to clean
the skin before using Silk’n™.
Use of Silk’n™ may cause temporary pigmentation changes (See “Possible Side Effects” below).
Keep this device out of the reach of children. Do not use Silk’n™ on children or allow children to use it.
2.5. Reducing the risk of injury
As with any electrical device, certain precautions must be taken in order to ensure your safety when using Silk’n™.
Keep Silk’n™ away from water!
Silk’n™ is an electrical device. As such it should always be kept away from water.
Do not place or store Silk’n™ where it can fall or be pushed into a tub, sink or any other vessel containing water. Do not place in, or drop into water or
any other liquid.
This may cause severe electrocution.
Do not use Silk’n™ while bathing.
Do not use Silk’n™ if it becomes damp or wet.
Do not reach for Silk’n™ if it has fallen into water.
Unplug Silk’n™ immediately if it has fallen into water.
Keep Silk’n™ away from water!
Never open Silk’n™!
Do not attempt to open or repair your Silk’n™ device. Opening Silk’n™ may expose you to dangerous electrical components and to pulsed light
energy, either of which may cause serious bodily damage and/or permanent eye injury.
10
Trying to open Silk’n™ may also damage the device and will void your warranty.
Please contact Silk’n™ Customer Service if you have a broken or damaged device in need of repair.
Use Silk’n™ only for its intended use and as described in its manual.
Silk’n™ should never be left unattended when plugged into an outlet.ֿ
Do not operate Silk’n™ if it has a damaged cord or plug and keep the power cord away from heated surfaces.
Do not use Silk’n™ if you see or smell smoke when it is in use.
Do not use Silk’n™ if it is not working properly or if it appears damaged.
Do not use Silk’n™ if the fan vent in its APPLICATORis cracked, coming off or missing.
Do not use Silk’n™ if the outer shell is cracked or is coming apart.
Do not use Silk’n™ with a damaged DISPOSABLE LAMP CARTRIDGE, or if its OPTICAL LENS is cracked, chipped or missing
Always unplug Silk’n™ from the electrical outlet immediately after use.
Unplug Silk’n™ before cleaning.
Do not use Silk’n™ with any attachments or accessories not recommended by Home Skinovations Ltd.
Minor Skin Discomfort
Although home pulsed light hair removal is generally very well-tolerated, most users do feel some mild discomfort during use, usually described
as being a mild stinging sensation on the treated skin areas. The stinging sensation usually lasts during the time of the application itself or for a few
minutes thereafter. Anything beyond this minor discomfort is abnormal and means that either you should not continue to use Silk’n™ because you
are unable to tolerate the hair removal application, or that the energy level setting is too high.
Skin Redness
Your skin may become red right after using Silk’n™ or within 24 hours of using Silk’n™. Redness generally clears up within 24 hours. See your doctor
if redness does not go away within 2 to 3 days.
Increased Sensitivity of the Skin
The skin of the treated area is more sensitive so you may encounter dryness or flaking of the skin.
Skin Wounds and Burns
Very rarely, burns or wounds to the skin can occur following the application. The burn or wound can require a few weeks to heal and, extremely rarely, may
leave a noticeable permanent scar.
Scarring
Although very rare, permanent scarring may occur. Usually when scarring occurs, it is in the form of a flat and white lesion on the skin (hypotrophic).
However, it can be large and red (hypertrophic) or large and extend beyond the margins of the injury itself (keloid). Subsequent aesthetic treatments
may be required to improve the appearance of the scar.
Do not attempt to open or repair your Silk’n™ device. Only authorized Silk’n™ repair centers are permitted to
perform repairs.
2.6. Possible Side Effects using Silk’n™
When used according to the instructions, side effects and complications associated with use of Silk’n™ are uncommon.
However every cosmetic procedure, including those designed for home use, involves some degree of risk. Therefore it is important that you understand
and accept the risks and complications that can occur with pulsed light hair removal systems designed for home use.
11
Pigment Changes
Silk’n™ targets the hair shaft, in particular the pigmented cells in the hair follicle and the hair follicle itself. Nevertheless there is risk of temporary
hyperpigmentation (increased pigment or brown discoloration) or hypopigmentation (whitening) to the surrounding skin. This risk of changes in skin
pigmentation is higher for people with darker skin tones.
Usually discoloration or changes to skin pigment are temporary and permanent hyperpigmentation or hypopigmentation rarely occur.
Excessive Redness and Swelling
In rare cases treated skin may become very red and swollen. This is more common in sensitive areas of the body. The redness and swelling should subside within
2 to 7 days and should be treated with frequent applications of ice. Gentle cleansing is OK, but one should avoid exposure to sun.
Infection
Infection of the skin is exceedingly rare but is still a possible risk following a skin burn or wound caused by Silk’n™.
Bruising
Very rarely, use of Silk’n™ may cause blue-purple bruising that can last 5 to 10 days. As the bruising fades, there may be a rust-brown discoloration
of the skin (hyperpigmentation) that can be permanent.
3.1. How does light remove hair?
Light-based hair removal is based on the theory of selective photothermolysis in which optical energy is used to disable hair growth. In order to achieve
such thermal effect the hair shaft needs to selectively absorb light energy and transform it into heat. This selectivity is achieved when optical energy that
is delivered to the tissue is mostly absorbed by hair shaft pigment, while the skin and the surrounding tissue stays cool. Melanin is the pigment in the
hair shaft that is responsible for the absorption of the light, which generates the heat that eventually disables hair growth. Therefore the more melanin
present in the hair (i.e. the darker the hair) the more light that can be absorbed and the more effective light can be at removing hair.
After Silk’n™ ApplicationDuring Silk’n™ pulse
Before Silk’n™ Application
3. Long Term Hair Removal the Silk’n
TM
Way
3.2. How does the hair growth cycle impact light-based hair removal?
Every hair in our body goes through the three phases of the hair growth cycle: Anagen, Catagen and Telogen. These phases have an important impact
on how the process of light-based hair removal works.
Anagen is the hair growth phase while Catagen and Telogen, both are resting phases.
The time it takes to complete a full hair growth cycle varies from person to person and the location of the hair on the body, but is typically 18-24 months.
12
3.3. What is different about Home Pulsed Light™ technology
in Silk’n™?
Silk’n™ utilizes the patent pending Home Pulsed Light™ technology
(HPL™) developed by the scientists at Home Skinovations exclusively
for safe and effective removal of unwanted hair at home. The technology
allows for Silk’n™ to be small, portable and easy to operate compared to
other similar systems. And like other light and laser systems HPL™ uses
light energy to target melanin pigment in the hair.
3.4. Plan your Silk’n™ hair removal for best results
A typical full hair growth cycle may take 18-24 months. During this time multiple Silk’n™ sessions may be required in order to achieve long
term hair removal.
The efficiency of hair removal varies from person to person according to body area, hair color, and how Silk’n™ is used.
Typical Silk’n™ hair removal plan during a full hair growth cycle:
The first 3-4 hair removal sessions withSilk’n™ will be approximately two weeks apart.
Hair removal sessions 5-7 withSilk’n™ will be approximately four weeks apart.
After that you will typically use Silk’n™ again from time to time if and when needed, until long-term results are achieved.
Typical maintenance with Silk’n™ after achieving long-term hair removal:
Due to hormonal or other physiological changes dormant hair follicles may become active. Maintenance
hair removal sessions with Silk’n™ may be required
from time to time.
18-24
Months
Anagen
Telagen
Catagen
At any given moment the majority of the hair follicles in any skin area are
in the resting phases. These resting hairs cannot be affected by Silk’n™.
However, hairs in the growing Anagen phase will respond to Silk’n™
applications. It is important to understand that it may take a full hair growth
cycle to realize complete hair removal results with Silk’n™.
ASE UNIT you can find the Silk'n™ CONTROL PANEL including POWER ON/OFF SWITCH and POWER INDICATOR LIGHT, the ENERGY LEVEL SETTING BUTTONS and
ENERGY LEVEL INDICATORLIGHTS, the AUDIO ON/OFF SWITCH, READY INDICATOR, SYSTEM W ARNING INDICATOR LIGHT and CARTRIDGE90% and 100% USAGE INDICATOR LIGHTS.
On the Silk'n™ APPLICATOR you can find the PULSE BUTTON. The DISPOSABLE LAMP CARTRIDGE is located at the APPLICATOR T IP.
4. First steps with Silk’n™
1
6
5
4
2
3
3
8
7
10
9
11
12
15
14
13
Base unit
Applicator
Pulse Button
Disposable Lamp Cartridge
Applicator Tip
Control Panel
Power ON/OFF switch
Power Indicator Lights
Energy Level Settings Buttons
Energy Level Indicator Lights
Ready Indicator Lights
Audio ON/OFF switch
Cartridge 90% Usage Indicator Light
Cartridge 100% Usage Indicator Light
System Warning Indicator Light
1
6
5
4
2
8
7
9
11
12
15
14
3
13
10
4.2. Package contents
Upon opening the Silk'n™ package, you will find the following parts:
Silk'n™ BASE UNIT and APPLICATOR
An AC cord
A second DISPOSABLE LAMP CARTRIDGE
This User’s Manual and a Quick Start Guide leaflet
An Instructional DVD
4.3. Silk’n™ Setup
1. Remove Silk’n™ BASE UNIT, APPLICATOR and other components from box.
Insert the APPLICATOR into its cradle in the Silk’n™ BASE UNIT.
2. Verify that the DISPOSABLE LAMP CARTRIDGE is inserted correctly into the APPLICATOR.
3. Plug the power cord into the Silk’n™ BASE UNIT socket.
4. Plug the other end of the power cord into an electrical outlet. Your Silk’n™ is now ready to start.
14
Energy Level
Energy level determines the intensity of the Silk’n™ light pulse delivered to your skin, from the lowest level (-) to the highest level (+).
Corresponding INDICATOR LIGHTS on the CONTROL PANELrepresent the increases in energy. As energy level increases, so does hair removal results as
well as the risk of possible side effects and complications.
Always start your first Silk’n™ hair removal session at the lowest energy setting.
If you experience little or no discomfort during and after the hair removal session using the lowest energy level, raise the energy level by one
I
NDICATOR LIGHT at the next session, and so on for each subsequent session.
Do not raise the energy level if you experience abnormal discomfort during or after treating with Silk'n™! (See section
2.6 - “Possible Side Effects”)
Do not raise the energy level during hair removal session even if you experience no discomfort. Discomfort may also appear
some time after the session.
Whenever Silk’n™ is turned on its energy level will automatically be reset to the lowest energy level. Only one ENERGY LEVELINDICATOR LIGHT will be on.
To set the energy level, press the ENERGY LEVEL SETTING BUTTONSusing “-“ or “+” to respectively decrease or increase the energy level. The number of
ENERGY LEVELINDICATOR LIGHTS will coincide with the change in energy level.
For your safety, when using Silk’n™ for the very first time, the system is automatically set to deliver the first 50 pulses at the lowest energy level, and
the next 200 pulses at up to level 3.
To cancel these safety settings press and hold the “+” and ”-“ ENERGY LEVEL SETTING BUTTONS simultaneously until you hear 2 consecutive “beep” sounds.
To restore these safety settings press and hold the “+” and ”-“ ENERGY LEVEL SETTING BUTTONS simultaneously until you hear 3 consecutive “beep” sounds.
4. Using firm pressure, apply the APPLICATOR TIP to the skin. Be sure that the skin area you are about to treat is spread evenly and smoothly, and that the
APPLICATOR T IP is in full contact with the skin.
5. Press the PULSE BUTTON to emit a pulse. You will then see a flash of light and hear a subtle pop-like sound. This is a normal light pulse of Silk’n™.
Note: As this intense pulse may be disturbing to your eyes, it is recommended to close them shortly before
pressing the PULSE BUTTON.
Firmly press the APPLICATOR T IP against the skin
6. After emitting a pulse, remove the APPLICATOR TIP from the skin. Silk’n™ will recharge for the
next pulse.
7. After approx. 3.5 seconds the READY INDICATOR LIGHT will turn on again, accompanied by a beep, to
indicate that your Silk’n™ is ready for another pulse.
8. Continue to administer pulses until the desired skin area is fully treated.
4.4. Treating with Silk’n™ for the first time
The skin should be shaved, clean, dry and free of any powders, antiperspirants or deodorants.
1. Press the P
OWER ON/OFF SWITCH to turn Silk’n™ on.
2. Shortly after pressing the POWER ON/OFF SWITCH, the READY INDICATOR LIGHT will turn on, accompanied by a beep, to indicate that your Silk’n™ is ready
for its first pulse.
3. Your Silk’n™ is automatically set to the lowest energy level.
15
Covering skin areas
Silk’n™ pulses should be administered in rows, starting at one end of each row and progressing sequentially towards
the other end. This technique allows better control of skin coverage, and helps you avoid treating the same area more
than once or overlapping skin areas.
When applied to the skin, the Silk’n™ APPLICATOR TIP is designed to create temporary pressure marks on the
treated area. These visible marks can be used for proper positioning of the next pulse.
Try to avoid overlapping pulses!
Do not treat the same area of skin more than once per hair removal session!
If your skin blisters or burns, STOP USE IMMEDIATELY!
4.5. What to Expect when treating with Silk’n™?
For many people, using Silk’n™ may be their first experience with a light-based device designed for home use. Silk’n™ is simple to use, and hair removal
sessions go by quickly. During a Silk’n™ session it is normal to experience and feel:
A Flash of Light – The bright light of Silk’n™ will not harm the eyes when applied to non-facial sites, and special eye-protection is not needed
when using Silk’n™.
A Fan Noise – The cooling fan in Silk’n™ makes noise similar to a hairdryer. This is normal.
A Pop Sound with Each Pulse – When a pulse of HPL™ light is activated, it is normal to hear a subtle pop sound simultaneously with the flash of light.
Moderate Pressure of the APPLICATOR – This is necessary and helpful for placement of adjacent pulses of light, and is part of the unique safety
feature of Silk’n™.
A Sensation of Warmth and Tingling – During each pulse of light it is normal to feel a mild sensation of warmth and tingling from the light energy.
Remember it is important to always use low energy settings for initial hair removal sessions. You may feel some warmth for up to an hour after
your Silk’n™ session.
Some Mild Red or Pink Color – During and just after your Silk’n™ session it is not uncommon to see some very mild, pink-like color of the skin. This is
usually most noticeable around the hairs themselves. However if you see full redness of the skin, blistering or burns stop use of Silk’n™ immediately.
4.6. After treating with Silk’n™
When Silk’n™ session has been completed turn Silk’n™ off by pressing the POWER ON/OFF SWITCH. (Be sure to remember the last energy level setting
you used, as it will not be restored when turning Silk’n™ on again.)
Unplug the power cord from the electrical outlet.
After each hair removal session it is recommended that you clean your Silk’n™ device, especially the APPLICATOR T IP (See section 5.1: “Cleaning Silk’n™”).
After cleaning, it is recommended to store your Silk’n™ device in its original box, and keep it away from water.
16
Side effects and complications
Some patients may experience pigmentation changes resulting from treating with Silk’n™. These effects, if they occur, are
generally mild and transient.
In case you experience any complication (See section 2.6 Possible Side Effects using Silk’n™) please contact your
physician immediately.
5. Maintenance of Silk’n™
5.1. Cleaning Silk’n™
After each hair removal session, it is recommended to clean your Silk’n™ device, and especially the APPLICATOR T IP.
Unplug Silk’n™ before cleaning.
Use a dry, clean cloth and a specially formulated cleaner for electronic equipment to gently wipe Silk’n™ surface, and especially the APPLICATOR T IP.
Never immerse Silk’n™ or any of its parts in water!
5.2. Replacing the LAMP CARTRIDGE
The Silk’n™ DISPOSABLE LAMP CARTRIDGE can fire 750 light pulses that would typically cover 2 Legs, Arms, Under arms, and Bikini line. Pulse intensity is determined
only according to the energy level setting of the device. There is no decrease of energy during the usable lifetime of the LAMP CARTRIDGE.
When a DISPOSABLE LAMP CARTRIDGE has reached 90% of its possible lifetime the CARTRIDGE 90% USAGE INDICATOR LIGHT on the CONTROL PANEL will be activated, indicating
that the DISPOSABLE LAMP CARTRIDGE should soon be replaced.
Once all 750 pulses in a DISPOSABLE LAMP CARTRIDGE have been used the CARTRIDGE 100% USAGE INDICATOR LIGHT will be activated, indicating that further pulses can
not be emitted.
In order to continue the hair removal session, it will now be necessary to replace the DISPOSABLE LAMP CARTRIDGE.
To replace a DISPOSABLE LAMP CARTRIDGE:
1. Press the POWER ON/OFF SWITCH to turn Silk’n™ off.
2. Unplug the power cord from the electrical outlet.
3. Grasp the used DISPOSABLE LAMP CARTRIDGE on both sides,
pull it out of the socket and discard with normal trash.
4. Unwrap a new DISPOSABLE LAMP CARTRIDGE.
5. Line up the holes in the APPLICATOR socket with the metal and
plastic hinges in the new DISPOSABLE LAMP CARTRIDGE,
and push it gently into place.
If correctly installed, the DISPOSABLE LAMP CARTRIDGE will spring back when pushed in and released.
Note: A DISPOSABLE LAMP CARTRIDGE should also be replaced if large spots appear inside it or if its LENSis broken.
Skin care following hair removal session
Do not expose treated areas of skin to the sun. Be sure to carefully protect the treated skin with sunscreen, throughout
the hair removal period and for at least 2 weeks following the last Silk’n™ session.
17
6.2. “A light pulse is not emitted when I press the PULSE SWITCH”.
Make sure that you have good contact with the skin and that the A
PPLICATOR TIP is evenly and firmly pressed to the skin. For your safety, the PULSE BUTTON
will activate a pulse only if the APPLICATOR T IP is firmly pressed against the skin.
Check the C
ARTRIDGE 100% USAGE INDICATOR If it is on, disconnect Silk’n™ and replace the DISPOSABLE LAMP CARTRIDGE.
Make sure that the READY INDICATOR is on.
If within 10 seconds the READY INDICATOR remains off turn Silk’n™ off and back on by pressing the POWER ON/OFF SWITCH twice.
If the problem persists, contact your local Silk’n™ Customer Service Center.
Check the SYSTEM W ARNINGINDICATOR LIGHT.
If the light is on turn Silk’n™ off and back on by pressing the POWER ON/OFF SWITCH twice.
If the problem persists, contact your local Silk’n™ Customer Service Center.
If these problems persist, contact your local Silk’n™ Customer Service Center.
a.
b.
a.
b.
6.1. “My Silk’n™ does not start.”
Make sure the power cord is properly connected to the Silk’n™ device.
Make sure the power cord is plugged into an electrical outlet on the wall.
6. Troubleshooting
Do not attempt to open or repair your Silk’n™ device. Only authorized Silk’n™ repair centers are permitted
to perform repairs.
Opening Silk’n™ may expose you to dangerous electrical components and to pulsed light energy, either of which may cause serious bodily damage and/
or permanent eye injury.
Trying to open Silk’n™ may also damage the device and will void your warranty.
Please contact Silk’n™ Customer Service if you have a broken or damaged device in need or repair.
For more information about Silk'n™ please enter your local website:
Australia: www.silkn.com.au
New Zealand: www.silkn. co.nz
If your Silk’n™ is broken, damaged, in need of repair, or for any other Silk’n™ user assistance, please contact your local Silk’n™ Customer Service:
Australia: contact@silkn.com.au 1-800-172220
New Zealand: contact@silkn.co.nz 0-800-172220
UK: contact@silkn.co.uk
7. Customer Service
Hong Kong: www.silkn.hk
Singapore: www.silkn.sg
Hong Kong: contact@silkn.hk
Singapore: contact@silkn.sg
UK: www.silkn.co.uk
18
1. Does Silk’n™ really work?
Yes. In clinical trials held by physicians, Silk’n™ was proven to safely achieve long-term hair removal results.
2. Where on my body can I use Silk’n™?
The Silk’n™ device has been designed for body hair removal anywhere below the neck. The most common areas treated with Silk’n™ are: legs, underarms, arms
and bikini line. It is not recommended to use Silk’n™ on the face. Silk’n™ is not suitable for everyone. We recommend that you read all the Silk’n™ warnings
and contraindications in this User’s Manual.
3. How long does a Silk’n™ treatment session take?
The time can vary depending on the area of the body treated. A full leg can take up to 30 minutes, or two underarms could take 10 minutes. Because Silk’n™
runs on regular electric power it can be used for as long as needed to complete a full hair removal session of the desired body part(s).
4. Is Silk’n™ safe?
Silk’n™ has been designed with your safety in mind, and tested and approved by top dermatologists and plastic surgeons to meet their safety standards for a
home-use device. But like any skin product or electronic device, one must use according to the operating instructions and user precautions.
5. Will Silk’n™ hurt?
When used properly most users of Silk’n™ report feeling a slight sensation of heat at the time of the pulse of light. Users with thicker and darker hairs may
feel slightly more discomfort, but this discomfort subsides once the hair removal session is completed. For your convenience Silk’n™ has five setting levels that
can be used according to your sensitivity.
6. How often should I use Silk’n™?
Hair removal sessions with Silk’n™ should be spaced every two weeks for the first three to four sessions. After that hair removal sessions should be done if
hairs have grown back, until the desired results are achieved.
7. Is Silk’n™ effective on white, grey or blonde hairs?
Silk’n™ works best on darker hair types, or hair that contains more melanin. Melanin is the pigment that gives hair and skin their color, and will absorb light energy.
Black and dark brown respond the best, although brown and light brown hairs will also respond but typically require more hair removal sessions. Red may show
some response. White, grey or blonde hairs usually don’t respond to Silk’n™ though some users have noted results after multiple hair removal sessions.
8. Can I use Silk’n™ on brown or black skin?
Do not use Silk’n™ on naturally dark skin complexion! Silk’n™ removes unwanted hair by selectively addressing hair pigment. Varied quantities of pigment also exist in
the surrounding tissue of skin. The quantity of pigment in a particular person’s skin, which is manifested by their skin complexion, determines the degree of risk they are
exposed to using Silk’n™. Treating dark skin with Silk’n™ can result in adverse effects such as burns, blisters, and skin color changes (hyper- or hypo-pigmentation).
9. When will I see results from Silk’n™?
As with any light-based or laser hair removal device, results are not immediate, and in fact you may not think anything happened at all. Hair may sometimes appear to
be growing back after a hair removal session, but typically after two weeks many of these hairs will simply fall out. Additionally hairs grow in three different stages and
only hairs in an active growth stage will be affected by Silk’n™. This is one of the main reasons that multiple sessions are required to achieve the desired result.
10. Can a man use Silk’n™?
Though designed exclusively for women, Silk’n™ may be suitable for use by men. However, hairs on men, typically those on the chest, will require more hair removal
sessions than that of women to get the desired results. As with women, using Silk’n™ on men’s facial hair such as beard and mustache, is not recommended.
11. Why is my hair growing, even though I treated it a week ago?
It is quite common for hair to appear as if it is still growing up to two weeks after a hair removal session with Silk’n™. This process is known as “ejection” and
at around two-weeks you’ll see that these hairs simply fall out or slide out with a slight tug. (We don’t however recommend pulling on the hairs – just let them
come out naturally.) It is also possible that some hairs, due to missed application or different stages of growth, were not affected by Silk’n™. These hairs will be
treated in follow-up sessions, and hence the reason multiple hair removal sessions are needed to get the best result with Silk’n™.
12. I’ve heard that some hairs grow back lighter and finer after light based hair removal?
This phenomenon is well documented amongst aestheticians and doctors using light and laser devices for hair removal. It is possible that some hairs will grow back lighter
and finer after hair removal with Silk’n™. Usually these hairs are a fraction of what was originally there, and continued use may have a desirable effect on them.
13. Why can’t I treat myself if I have an “active” suntan?
Do not use Silk’n™ on tanned skin or after sun exposure! Tanned skin and particularly following sun exposure, contains large quantities of the pigment Melanin.
8. Frequently Asked Questions
19
This applies to all skin types and complexions, including those which don’t seem to tan quickly. The presence of large quantities of Melanin exposes the skin to
higher risk of adverse effects when using Silk’n™ including burns, blisters, and skin color changes (hyper- or hypo-pigmentation).
14. Is long-term use of Silk’n™ dangerous for my skin?
The use of light and laser energy in aesthetic medicine has been well documented for over 15 years in professional peer-reviewed journals, and by well respected
institutions like the Mayo Clinic. These journals and institutions have not reported any side-effects or damage from long-term use of light and laser device.
15. Can I use Silk’n™ to remove my chin hair or elsewhere on my face?
It is not recommended to use Silk’n™ on the face or neck. Unlike body hair, most of women’s potential facial hair remains inactive and hidden, while only a
fraction of it grows and surfaces. Exposing facial hair to the light pulses of Silk’n™ may remove apparent hair but simultaneously stimulate unwanted growth of
hidden hair. In addition, using Silk’n™ to remove facial hair may cause serious eye injury.
16. How long should I wait to treat with Silk’n™ after unprotected exposure to the sun?
One should wait 4 weeks before using Silk’n™ after unprotected exposure to the sun. However, if there is ever any uncertainty about sun exposure please
contact your physician or Home Skinovations customer support.
17. Should I do anything before using Silk’n™?
Before any Silk’n™ session it is important to avoid sun exposure on the treated area for at least four weeks. A high level UV Sun Screen (SPF 50+) will help,
as will clothing covering the treated area. The area to be treated should also be cleaned with mild soap and water, and the hairs shaved down to skin level.
18. How should I care for the treatment area after using Silk’n™?
The area treated with Silk’n™ can be cleaned and maintained with standard skin care products. Special care must be taken to avoid unprotected sun exposure.
Strong sunscreens (50+ SPF) and covering clothing are suitable for protection from the sun.
19. Should I pull the hairs out after treatment?
No, let the hairs gradually fall out on their own. This may take up to 2 weeks.
9. Specifications
Spot Size
Speed
Technology
Max Energy Level
Wavelength
Charging Time/Power Source
Electrical Requirements
Time Needed to Treat Lower
Legs
Operation and Safety
Package Size
System Weight
2cm x 3cm [6cm
2
]
1 pulse every 3.5 second: 1.7 cm
2
/sec
New Home Pulsed Light™
Max 5J/cm
2
475-1200nm
Continuous operation
100-240VAC, 2A
30 minutes
Safety sensor tip enables self-trigger for maximum
safety & control. Easy to use on all body parts
Height 9 inch, Width 9 inch, Depth 5.2 inch
4 pounds
20
10. Labeling
21
Class II equipment
Degree of protection against electric shock: type BF applied part
WEEE - Waste Electrical and Electronic Equipment
CE Mark
Follow operating instructions
This device comply with Part 15 of the (FCC)
Federal Communications Commission Rules.
Degree of protection against ingress water: ordinary
This device is not suitable for use in the presence of flammable anesthetic
mixture with air or with Oxygen or Nitrous Oxide.
22
EC Declaration of Conformity
We Home Skinovations Ltd. declare under our sole responsibility that
the home Skin treatment products
Brand name: Home Skinovations
Model name: Silk’n; Disposable Lamp Cartridge
Models Number: AS100001E, AS100674B, AS100756A
are fully in conformity with the essential requirements of Council Directive
89/336/EEC and 73/23/EEC amended by Directives 93/68/EEC.
This declaration is based on the full compliance of the products with
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Silkn AS100674B bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Silkn AS100674B in de taal/talen: Engels als bijlage per email.
De handleiding is 0,89 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Stel vragen via chat aan uw handleiding
Stel uw vraag over deze PDF
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.