300747
61
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
59
Customer Service & Assistance
Gigaset E490/E495 / GBR / A31008-M2105-L101-2-7619 / appendix.fm / 15.05.2013
Version 4, 16.09.2005
Questions and answers
If you have any questions about the use
of your phone, you can contact us 24/7
at www.gigaset.com/service
. The table
below contains a list of common problems
and possible solutions.
E495 Gigaset only:
The display is blank.
1. The handset is not switched on.
¥ Press and hold the end call key a.
2. The batteries are flat.
¥ Charge or replace the batteries
(
¢page 10).
"Base x" flashes on the display.
1. The handset is outside the range of the base
station.
¥ Move the handset closer to the base sta-
tion.
The base station's range is reduced because
eco mode is activated.
¥ Deactivate eco mode (¢ page 45) or
reduce the distance between the handset
and the base station.
2. The base station is not turned on.
¥ Check the base station's mains adapter
(
¢page 8).
"Please register" flashes in the display.
Handset has not been registered with the base
station or has been deregistered.
¥ Register the handset (¢page 46).
Handset does not ring.
1. The ringer is deactivated.
¥ Activate the ringer (¢page 53).
2. Call divert set to All Calls.
¥ Deactivate call divert (¢ page 25).
You cannot hear a ringer/dialling tone from the
fixed line network.
The phone cord supplied has not been used or
has been replaced by a new cord with the wrong
pin connections.
¥ Please always use the phone cord supplied or
ensure that the pin connections are correct
when purchasing from a retailer (
¢page 8).
Error tone sounds after system PIN prompt
You have entered the wrong system PIN.
¥ Reset the system PIN to 0000 (¢page 55).
Forgotten the system PIN.
¥ Reset the system PIN to 0000 (¢page 55).
Call charges are not displayed.
1. Your network provider does not support this
feature.
2. There are no metering pulses.
¥ Ask your network provider to transmit the
metering pulses.
The other party cannot hear you.
You have pressed the
u (INT) key. The handset
is "muted".
¥ Activate the microphone again (¢page 23).
The number of the caller is not displayed
despite CLIP.
Calling Line Identification is not enabled.
¥ The caller should ask the network provider to
enable Calling Line Identification (CLI).
You hear an error tone when keying an input
(a descending tone sequence).
Action has failed/invalid input.
¥ Repeat the operation.
Watch the display and refer to the user guide if
necessary.
You cannot listen to messages on the network
mailbox.
Your PABX is set for dial pulsing.
¥ Set your PABX to tone dialling.
No time is specified for a message in the calls
list.
Date and time have not been set.
¥ Set the date/time (¢page 13).
The answering machine announces "PIN is
incorrect" during remote operation.
1. You have entered the wrong system PIN.
¥ Enter the system PIN again.
2. The system PIN is still set to 0000.
¥ Change the system PIN (¢page 55).
The answering machine is not recording any
messages/has switched over to announce only.
Its memory is full.
¥ Delete old messages.
¥ Play back new messages and delete.
61

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens gigaset e490 twin bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens gigaset e490 twin in de taal/talen: Engels als bijlage per email.

De handleiding is 1,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Siemens gigaset e490 twin

Siemens gigaset e490 twin Gebruiksaanwijzing - Nederlands - 80 pagina's

Siemens gigaset e490 twin Gebruiksaanwijzing - Deutsch - 84 pagina's

Siemens gigaset e490 twin Gebruiksaanwijzing - Français - 76 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info