41501
10
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
10/16
Siemens Building Technologies Raumtemperaturregler REV23RF CE1N2265en
HVAC Products 20.08.2002
Refer to the Installation Instructions printed on the package.
The receiver must be wired with the power supply switched off.
Mains voltage may be switched on again only after the unit is completely
mounted.
When mounting the unit, the base must first be fitted and wired (L/N = AC 230 V
mains supply, LX/L1 = consumers). Then, engage the unit at the top, swing it down-
ward and secure it with a screw
For more detailed information, refer to the Installation Instructions supplied with the
unit
For the electrical installation, the local safety regulations must be complied with.
It is recommended to first commission and switch on the receiver, then the transmitter.
Switch on mains supply
a) Press the «Reset» button (= delete) for about 3 seconds, LED flashes for about 5
seconds (deleting the stored address)
b) Press «Set» button (= setting / learning) for about 1 second until the LED lights
up
c) The duration of the receiver’s learning readiness is a maximum of 25 minutes.
If no signal is received from the transmitter during that period of time, repeat
steps b) and c)
d) Mount transmitter and put it into operation
e) When the receiver receives a signal from the transmitter, the LED flashes briefly
f) When the LED is steady on, the relay is energized = controlled device ON
g) When the LED is dark, the relay is deenergized = controlled device OFF
h) In the event of a power failure at the receiver, the relay will automatically be de-
energized.
The transmitter repeats the ON or OFF signal at 20-minute intervals, depending
on the operating state. This means that the relay will be energized / deenergized
again after 20 minutes at the latest. This interval was selected to extend battery
life.
If the REV-R.02/1 receives no signal from the controller / transmitter for 60 minutes, the
relay will drop out so that the controlled device will automatically be switched off.
It is recommended to first commission the receiver and then the transmitter.
If the reference room is equipped with thermostatic radiator valves, they must be fully
opened
a) Remove the battery transit tab, which prevents inadvertent operation of the unit
during transport and storage. The unit switches on
b) When – immediately after switching on – symbol
or appears on the
display (controlled device ON), the first signal has already been sent to the re-
ceiver and communication has been opened
c) Make the settings according to the Operating Instructions
d) If symbol
or does not appear on the display (controlled device OFF), it
must first be activated for signal transmission
e) Select operating mode
(comfort mode)
f) On menu T, select the setpoint for comfort mode
g) Use the roller selector to adjust the setpoint to 29 °C and confirm by pressing
h) Heating ON symbol
or appears on the display after a maximum of one
minute
i) The first signal transmission to the receiver has taken place
j) After 10 seconds, the transmitter sends another signal
Support
Mounting and installa-
tion of receiver
REV-R.02/1
Commissioning
Receiver
REV-R.02/1
Commissioning
Controller / transmit-
ter REV23RF
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens REV23RF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens REV23RF in de taal/talen: Engels als bijlage per email.

De handleiding is 0,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Siemens REV23RF

Siemens REV23RF Gebruiksaanwijzing - Nederlands - 15 pagina's

Siemens REV23RF Gebruiksaanwijzing - Nederlands - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info