620392
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
CE1B3172en / 26 Nov 2009 Subject to change Siemens Building Technologies
Temporary timer to extend the Comfort mode
When Energy Saving operating mode is active, press operating mode button
to temporarily return to Comfort mode.
symbol appears. Press opera-
ting mode button
again to stop the timer.
You can only extend Comfort mode if parameter P02 = 1.
Duration * : P68 = 0...360 min, factory setting = 0 min.
Button lock
Press operating mode button
for 5 seconds to lock or unlock the buttons if
manual button lock is configured (parameter P14 = 2).
The thermostat automatically locks the buttons 20 seconds after the last
adjustment if "Auto lock" is configured (P14 = 1).
The key symbol
indicates locked buttons.
External faults
* Needs to be configured by your HVAC installer
Commissioning
You can adjust a number of different control parameters to adapt the thermostat to your system and optimize control perfor-
mance. You can do this during operation either via the buttons on the thermostat or using a commissioning tool.
Control parameters
Proceed as follows to change the most important control parameters:
(Your HVAC installer can set additional parameters)
+ / –
1. Press the and + buttons simultaneously at least 3 seconds.
Release, and within 2 seconds, press + again for 3 seconds. "P01" is displayed.
2. Repeatedly press the + or button to select the required parameter.
P01 P02 P08 P14
+-+
--
+
3171z99
End
-
+
-
P13
+-
3. Press + and simultaneously. The current value of the selected parameter begins to flash, allowing you to change
the value by repeatedly pressing + or .
4. The next parameter is displayed when you press + and again simultaneously.
5. Repeat steps 2 to 4 to display and change additional parameters,.
6. Press + or until “End” is displayed, and then press + and simultaneously to save the change and exit parameter
entry mode.
Para-
meter
Description
Factory setting Setting range Adj
P01 Control sequence
1 (Cooling only)
0 = Heating only
1 = Cooling only
2 = Manual H or C
3 = Auto Changeover
P02
Mode selection by user via operating mode button
** Without time schedule via KNX, Auto is equal to
Comfort.
1 (Auto **,
Protection)
1 = Auto **, Protection
2 = Auto **, Comfort, Energy
Saving, Protection
P04 Selection of °C or °F °C 0 = °C
1 = °F
P05 Sensor calibration 0.0 °C – 3 ... +3 °C
P06 Standard temperature display 0 (Room temp.) 0 = Room temperature
1 = Setpoint
P07 Additional user information 0 (no display) 0 = No display
1 = Temp. in °C / °F
2 = Outside temperature (via
bus)
3 = Time of day (12h, via bus)
4 = Time of day (24h, via bus)
P08 Comfort basic setpoint 21 °C 5 ... 40 °C
P09 Minimum setpoint limitation in Comfort (WminComf) 5 °C 5 ... 40 °C
P10 Maximum setpoint limitation in Comfort (WmaxComf) 35 °C 5 ... 40 °C
P11 Setpoint of heating in Energy Saving (WheatEco) 15 °C OFF, 5 °C…WcoolEco
P12 Setpoint of cooling in Energy Saving (WcoolEco) 30 °C OFF, WheatEco…40°C
P14 Button lock
(Press operating mode button for 5 seconds to lock or unlock
the buttons)
0 (Disabled) 0 = Disabled
1 = Auto lock
2 = Manual lock
All temperature settings can be made in increments of 0.5 °C.
Please record all changes you make!
AL1 *
AL2 *
These messages inform you on external faults *:
AL1 : ...……………………… AL2 : ...………………………………….
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens RDU341 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens RDU341 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Siemens RDU341

Siemens RDU341 Gebruiksaanwijzing - Deutsch - 2 pagina's

Siemens RDU341 Installatiehandleiding - Alle talen - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info