620369
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
CB1B1440en / 2013-09-12 Subject to change Siemens Building Technologies 4/4
Control parameters
If you want to change the control parameters, proceed as follows:
+ / –
1. Set the thermostat to Frost Protection mode
.
2. Press + and simultaneously for at least 3 seconds.
Release the buttons and, within 2 seconds, press again for 7 seconds. The display will show "P02".
3. Select the required parameter by repeatedly pressing + or .
4. Press + and simultaneously. The current value of the selected parameter starts to flash. Adjust it by
pressing + or .
5. Press + and simultaneously again to display the next parameter.
6. If you wish to display and change additional parameters, repeat steps 3 through 5.
7. Service or expert level: 10 seconds after the last display or setting, all changes are stored and the
thermostat will leave the parameter setting mode.
Expert level: Press + or until "End" is displayed. Then, press + and – simultaneously to save the change
and exit the parameter setting mode.
No.
Thermostat’s parameter Factory setting Setting range
P02 Selection of operating mode via operating mode
button
1 = Frost Protection
Comfort mode
RDD310/EH:
1 = Comfort - Frost
Protection
2 = Comfort - Economy -
Frost Protection
RDE410/EH:
1 = Auto - Comfort -
Frost Protection
2 = Auto - Comfort -
Economy - Frost
Protection
P05 Temperature sensor calibration 0.0 °C -3…3 °C
P06 Standard temperature display 0 = Room
temperature
0 = Room temperature
1 = setpoint
P08 Comfort basic setpoint 20 °C 5...40 °C
P09 Min. setpoint limitation in Comfort mode (Wmin
Comf
) 5 °C 5...40 °C
P10 Max. setpoint limitation in Comfort mode (Wmax
Comf
) 35 °C 5...40 °C
P11 Heating setpoint in Economy mode 16 °C Off, 5…18 °C
P14 Button lock (press operating mode button for
3 seconds to lock or unlock)
0 = Disabled 0 = Disabled
1 = Auto lock
2 = Manual lock
P30 Switching differential in heating mode 1 K 0.5…6 K
P38 External input 0 0 = No input
1 = External sensor
input
P45 Heating system load in kW 2.8 kW 0…3.6 kW
P51 Floor heating temperature limit Off Off, 10...60 °C
P65 Setpoint of heating in Frost Protection mode (Wheat
Stb
)
8 °C Off, 5…18 °C
P69 Temporary setpoint in Comfort mode Off Off = Disabled
On = Enabled
P71 Reloading factory settings
Set value to "On" and confirm by pressing + and
Off Off = Idle
On = Reset
d02 Status X1 Diagnostics 0…xx °C = Measured
temperature
d07 Software version information No adjustment
(All temperature settings can be made in increments of 0.5 °C with the exception of P51, which is in 1 °C)
Please write down all changes you make!
1/4 CB1B1440en / 2013-09-12 Subject to change Siemens Building Technologies
s
Operating Instructions
RDD310/EH, RDE410/EH
RDD310/EH and RDE410/EH – the room thermostats for use with electrical floor heating systems. The products feature a
built-in room sensor to control the room temperature, and the user can connect a cable temperature sensor to limit the
maximum floor temperature. The thermostat provides Comfort, Economy and Frost Protection mode. The RDE410/EH also
features an Auto Timer with 8 programmable time switches. You can either rely on the factory settings or make adjustments
that suit your individual needs.
Are your rooms too warm or too cold?
+ /
Press + or to increase or decrease the current room temperature setpoint in increments of 0.5 C for
Comfort mode. 5 seconds after the last push, the room temperature setpoint is automatically saved. The
display stops flashing and shows the room temperature currently measured.
The maximum setpoint setting range is 5...40 °C, unless limited by parameters P09 and P10.
Do you require continuous Comfort mode?
/
Press the operating mode button
to switch to Comfort mode . In that case, the room temperature
setpoint is always maintained at the Comfort level.
The RDE410/EH has a dedicated
button for selection of the operating mode.
Display
Operation and settings
Buttons locked
Heating demand
Measured room temperature,
setpoints and parameters
Symbol when current room
temperature is displayed
Current time of day *
Colder/Warmer
Weekday 1…7 (1 = Monday/7 = Sunday)*
Confirmation
of settings
View and set Auto Timer
programs
Frost Protection/
system On
RDD310/EH
RDE410/EH
* RDE410/EH only
Time of day and weekday
Selection of operating mode
Auto Timer ( )
Comfort ( )
Economy (
)**
Selection of operating mode
- Frost Protection (
)
- Comfort ( )
- Economy ( ) **
Frost Protection mode
Comfort mode
Economy mode
Auto Timer mode *
Colder/Warmer
** If configured by your HVAC installer
CB1B1440en / 2013-09-12 Subject to change Siemens Building Technologies 2/4
Do you want to set your thermostat to Frost Protection mode?
/
Press operating mode button several times until the display shows the icon to indicate that Frost
Protection mode is selected.
The RDE410/EH has a dedicated
button to set the system either to Frost Protection mode or to switch it
on.
In Frost Protection mode
, the room temperature setpoint is maintained at 8 °C (factory setting), unless
your HVAC installer made some other setting.
Changes made by the installer Frost protection:............................ C
Do you want to change to Economy mode?
/
When Economy mode is enabled (parameter P02), press the operating mode button to select Economy
mode . In that case, the room temperature setpoint is always maintained at the Economy level. The
preset room temperature setpoint in Economy mode is 16 C (parameter P11).
The RDE410/EH has a dedicated button for selection of the desired operating mode.
Do you want to change to Auto Timer mode? (RDE410/EH only)
/
Press the
button to select Auto Timer mode . In this mode, the thermostat switches automatically
between Comfort and Economy mode according to the 8 programmed time switches.
Setting the time of day and the weekday (RDE410/EH only)
+ / –
+ / –
1. Keep the button depressed until the time digits start to flash, then press + or to set the time of day.
If the current time format is the 24-hour format and you wish to change to the 12-hour format, keep +
depressed to pass 23:59, or keep depressed to pass 00:00. Vice versa to go back to the 24-hour
format.
2. Confirm the time of day by pressing
. The weekday indicator starts to flash.
3. Press + or to set the current weekday.
4. Confirm the current weekday by pressing
.
Do you want to set the time switches? (RDE410/EH only)
A..
+ / –
A..
A..
To set the time switches, keep the button depressed for 3 seconds to go to Auto Timer mode.
This mode is indicated by "Ax" appearing on the display (x = Auto Timer 1...8) and the time xx:xx flashing.
For each time switch, proceed as follows:
1. Icons
and are displayed. Press + or to set the Comfort mode start time and confirm by
pressing .
2. Icons
and are displayed. Press + or to set the Comfort mode end time (or Economy mode start
time) and confirm by pressing
.
3. Icon flashes. Press + or to select or deselect each day and advance to the next day. Confirm
setting for the current time switch by pressing
and advance to the next time switch.
The thermostat exits the time switch setting mode automatically after 20 seconds if no button is pressed. All
changes made after the last press of
will not be saved!
Do you want to view the time switch settings? (RDE410/EH only)
Press the button to sequentially review all 8 programmable time switches.
Do you want to reload the default time switch settings? (RDE410/EH only)
+ / – /
Set the thermostat to Frost Protection mode
.
Press + and simultaneously for 3 seconds. Release the buttons and, within 2 seconds, press twice the
button.
Default
settings
Day/s Time of day when controller is in Comfort mode
Mo (1) – Fr (5) 06:30 – 08:30 (A1) 17:30 – 22:30 (A2)
Sa (6) 08:00 – 23:00 (A3)
Su (7) 08:00 – 22:30 (A4)
– During the remaining time, the RDE410/EH operates in Economy mode
– Time switches A5…A8 have no default settings
Commissioning (by qualified HVAC installer)
To adapt the thermostat to your system and to optimize the control performance, a number of control parameters can be set.
This can also be made during operation without opening the thermostat.
3/4 CB1B1440en / 2013-09-12 Subject to change Siemens Building Technologies
Recalibrating the temperature sensor
If the room temperature displayed by the thermostat does not accord with the temperature effectively
measured, the temperature sensor can be recalibrated. Using parameter P05, the temperature can be
adjusted by pressing + or – in increments of 0.5 °C. The maximum recalibration range is +/- 3 °C.
Economy mode
If you want to change the factory-set temperature setpoint (16 °C for heating), readjust parameter P11.
Caution: The setpoint for Economy mode can be set to "Off". This means that the thermostat will be
deactivated! This means that there will be no protective heating function, therefore risk of frost!
Electrical floor heating/cable temperature sensor (floor sensor)
The factory setting for this function is "Off" and must be set to "On" if electrical floor heating is used. This
function is activated via parameter P38.
The installer must select the approximate capacity of the heating system (in kW) via parameter P45 during
commissioning.
The cable temperature sensor is connected to input X1, M and acquires the floor temperature. If the floor
temperature exceeds the parameterized
limit xx ºC (P38 = 1, P51 = xx ºC), the heating system is turned off
until the floor temperature returns to a level below the parameterized limit. A typical application are rooms (dry
floor).
If the application does not require floor temperature limitation but instead uses the external sensor for room
temperature display and control, the parameters have to be set as follows: P38 = 1, P51 = Off. A typical
application are bathrooms (wet floor) where a constant floor temperature is required
It is not recommended to have only a built-in room sensor for floor heating since in that case there is a risk of
overheating.
Energy saving tips without loss of comfort:
Never allow room temperatures to exceed 21 °C
When absent, set the thermostat to Economy mode (or Frost Protection), even for short periods of time
Air out the rooms briefly, but with windows wide open
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens RDE410-EH bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens RDE410-EH in de taal/talen: Engels als bijlage per email.

De handleiding is 0,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Siemens RDE410-EH

Siemens RDE410-EH Gebruiksaanwijzing - Nederlands - 2 pagina's

Siemens RDE410-EH Gebruiksaanwijzing - Deutsch - 2 pagina's

Siemens RDE410-EH Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info