Handleiding Siemens Gigaset DA610 (pagina 11 van 15) (Engels)

504664

Verklein

Vergroot

Pagina terug

1/15

Pagina verder

Gigaset DA610 / en / A30350-M212-R102-8-UJ19 / telephony.fm / 29.03.2016

el en es it pt 11

1110-01

Network services

Public telephone systemsoffer you – in some cases only on request – a

range of helpful, additional services (e. g. call forwarding, callback when

busy, withheld number, etc.). These services can be selected using spec-

ified key combinations, of which your network provider will notify you.

Caller display (CLIP)

If the caller display service is activated, an incoming call is shown on the

display with the number and saved in the call list. Requirement: The

network provider supports the following service features and the num-

ber transfer is not withheld by the caller:

u CLI (Calling Line Identification): The caller's number is transferred.

u CLIP (Calling Line Identification Presentation): The caller's number is

displayed.

You can transfer this number to the phonebook and edit it (

£ page 7).

If you have saved the local dialling code (

£ page 11), a call with the

same dialling code is automatically only displayed as the number with-

out the dialling code.

Recall key

In public telephone systems the recall key (flash) is required for the use

of various additional services; e.g. for "callback when busy".

If necessary, the flash time on your telephone must be adjusted to the

requirements of the telephone system (

£ page 11).

Setting up a dialling code

If necessary you can change the default setting for the area code for your

connection which is saved in the telephone. The number saved here is

then used to display only the number of the person calling without the

area code in the call lists, provided they have the same area code.

You can enter two area codes.

K 4 Activate setting mode for the area code. The default num-

ber is displayed.

Q ... O / * / #

Enter the new area code (max. 5 digits).

To edit the second area code:

v Confirm with [ and continue.

To save the settings:

K Save your settings and exit the setting mode.

Note: The names of persons, whose numbers are stored in the phone-

book with the area code defined here, are no longer displayed. Change

the appropriate phonebook entries, where necessary.

Operation on a PABX

Special functions/Recall key

During an external call, you can make an enquiry or forward the call. To

do this, press the recall key

H. The subsequent procedure depends

on your PABX. To set the recall key, the telephone's flash time must be set

consistently with your PABX. Please refer to the operating instructions

for your PABX.

Changing the dialling mode/flash time

The telephone supports the following dialling modes:

u Tone dialling

u Pulse dialling

Depending on your PABX, you may need to change your phone's dialling

mode or the flash time. (Default setting: Tone dialling)

Changing the dialling mode

K # Activate setting mode for the dialling mode.

Press the key code for the dialling mode:

K Save your settings and exit the setting mode.

Temporary switch to tone dialling in "Pulse" position

To use functions that require tone dialling (e.g. remote control of

answering machine), you can set the telephone to tone dialling for the

duration of the call.

After the connection is established:

* Press the star key.

After the connection is terminated, the setting reverts to pulse dialling.

Changing the flash interval

You can change the flash interval if the dialling mode is set to tone dial-

ling (see above) (default setting 90 ms).

K  Activate setting mode.

O 5 Press the key code for setting the flash interval.

Q ... 4 Select the flash interval (ms):

K Press the set key to save your settings and exit the setting

mode.

Setting dialling prefixes

If your phone is connected to a PABX, you may have to use a dialling pre-

fix to make external calls. You can save up to three prefixes in your tele-

phone.

If a dialling prefix is recognised during dialling, a dialling pause will auto-

matically be applied. You can adjust the time of the dialling pause if nec-

essary (

£ page 12).

K Q Activate setting mode for the dialling prefix.

The current setting of the first dialling prefix is displayed.

Q ... O, *, #, H

Enter the dialling prefix (1 to 3 digits) and confirm with [.

Enter the next prefix and confirm with

u Hold down the control key X to delete the current dial-

ling prefix.

K Save your settings and exit the setting mode.



Tone dialling

Pulse dialling

0 = 90 1 = 120 2 = 270 3 = 375 4 = 600

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Siemens Gigaset DA610 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Siemens Gigaset DA610

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info