527448

Siemens ER926SV70N Handleiding

6
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
en
Read the appliance's instructions before
installing and using.
The graphics in these Assembly
instructions are given as a guide only.
The manufacturer is exempt from all
liability if this manual's requirements
are not complied with.
Safety instructions
All operations relating to installation,
regulation and conversion to other
types of gas must be carried out by
an authorised installation engineer,
respecting applicable regulations,
standards and the specifications of
the gas and electricity providers.
Before you begin, turn off the
appliance's electricity and gas
supply.
You are recommended to contact the
Technical Assistance Service to
convert to another type of gas.
This appliance has been designed for
home use only, not for commercial or
professional use. This appliance cannot
be installed on yachts or in caravans.
The warranty will only be valid if the
appliance is used for the purpose for
which it was designed.
Before installing, you need to check that
local distribution conditions (gas type
and pressure) and the appliance's
adjustment are compatible (see table I).
The appliance's adjustment conditions
are written on the label or the
specifications plate.
This appliance can only be installed in a
well-ventilated place in accordance with
existing regulations and ventilation
specifications. The appliance must not
be connected to a combustion product
evacuation device.
The supply cable must be attached to
the unit to prevent it from touching hot
parts of the oven or hob.
Appliances with electrical supply must
be earthed.
Do not tamper with the appliance's
interior. If necessary, call our Technical
Assistance Service.
Before installing
This appliance is class 3 type, according
to the EN 30-1-1 regulation for gas
appliances: built-in appliance.
The units next to the appliance must be
made of non-flammable materials. The
laminated covering and glue for
adhering it must be heat resistant.
This appliance cannot be installed
above fridges, washing machines,
dishwashers or similar.
An oven must have a power cooling fan
to install a hob above it.
Check the oven's dimensions in its
installation manual.
If an extractor fan is installed, you must
follow the installation manual's
instructions, always keeping a minimum
distance of 650 mm to the hob.
Preparation of kitchen unit
(fig. 1-2)
Make an appropriate size cut in the work
surface.
If the hob is electric or mixed (gas and
electricity) and there is no oven below,
place a non-flammable separator (e.g.
metal or plywood) 10 mm from the
bottom of the hob. This will prevent
access to the base of the hob.
If the hob is gas, it is recommendable to
place the separator at the same
distance.
On wood work surfaces, varnish the
cutting surfaces with a special glue. This
protects them from moisture which could
collect under the work surface.
Installation of appliance
The clips and the adhesive seal
(underside of the hob) are factory-fitted:
do not under any circumstances remove
them. The seal ensures that the entire
work surface will be watertight, and
prevents water seepage.
In order to fit the appliance into the
kitchen unit, first place the hob in the
correct position then loosen each of the
clips so that they all turn freely (it is not
necessary to completely undo them).
Insert and centre the hob.
Press the sides of the hob until it is
supported around its entire perimeter.
Turn the clips and tighten them fully.
Fig. 3
Removal of hob
Turn off the appliance's electricity and
gas supply.
Unscrew the clips and proceed in the
reverse order to installation.
Gas connection (fig. 4)
The end of the inlet connection point of
the gas hob has a 1/2” (20.955 mm)
thread that allows for:
- fixed connection.
- connection using a flexible metal pipe
(L min. 1 m - max. 3 m)
. In this case, it is
necessary to insert the accessory
(427950) and the watertight seal
(034308) supplied between the manifold
outlet and the gas supply. Fig. 4a.
In this case, you must prevent the pipe
from coming into contact with moving
parts of the kitchen unit being inserted
(for example, a drawer) and prevent
access to any spaces which might
become obstructed.
If you need to connect the gas supply
horizontally, our Technical Assistance
Service can supply you with an L-tube
(code 173018) and a seal (code
034308). Fig. 4b.
Warning! If any connection is handled,
check the seal.
Danger of leaks.
The manufacturer is not liable for any
connection leaking, after being handled.
Electric connection (fig. 5)
Check that the voltage and power of the
appliance are compatible with the
electrical installation.
The hobs are supplied with a power
cable with or without a wall socket plug.
Provide an omnipolar cut-off switch with
a minimum contact separation of 3 mm
(except for plug connections, if the user
has access to it).
Appliances with plugs must only be
connected to sockets that have earth
wires correctly installed.
This appliance is type “Y”: the supply
cable can only be changed by the
Technical Assistance Service and not
the user. The cable type and minimum
cross-section must be respected.
Changing the gas type
If the country's regulations allow, this
appliance can be adapted to other types
of gas (see specifications plate). The
components required for this are in the
transformation kit supplied (depending
on the model) available from our
Technical Assistance Service. The
following steps should be taken:
A) Changing the nozzles of the rapid,
semi-rapid and auxiliary burners on
the hob (fig. 6):
- Remove the pan supports, burner
covers and diffusers.
- Change the nozzles using the spanner
provided by our Technical Assistance
Service (code 424699), taking special
care to ensure that the nozzle does not
fall when it is removed from the burner or
when fitted.
Ensure that it is completely tightened in
order to guarantee the seal. Primary air
adjustment is not necessary with these
burners.
B) Changing the nozzles for double-
flame burners (fig. 7):
The glass panel and frame are fixed to
the rest of the hob using a clip mounting
system. The following steps must be
taken to remove the glass panel and
frame:
- Remove all the burner covers and pan
supports. Fig. 7a.
- Release the front clip fixing the
appliance to the kitchen unit by
removing the screw. Fig. 7b.
- Loosen the screws on the burners,
fig. 7c-7d, and remove the control knobs
from their respective housings.
Use the disassembly lever 483196
available from our Technical Assistance
Service. To release the front clips, apply
the lever in the area shown in figures 8
according to the hob model.
Never use the lever on glass edges
which have no trim or frame!
- To release the rear clips, carefully raise
the entire glass panel and frame, as in
fig. 8a.
Changing the outer flame nozzle
(fig. 9a):
- Loosen the clamp screw to release the
bushing by moving it backwards to
access the main nozzle easily. Fig. a1.
- Remove the outer flame nozzle by
turning it towards the left. Fig. a2-a3.
- Screw in the new outer flame nozzle.
Fig. a3-a4, as in table II.
- Adjust the distance of the airflow
adjusting bushing L2 according to the
value -Z- shown in table II. Fig. a5.
- Tighten the clamp screw. Fig. a6.
… 6 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens ER926SV70N bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens ER926SV70N in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks als bijlage per email.

De handleiding is 1,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Siemens ER926SV70N

Siemens ER926SV70N Gebruiksaanwijzing - Nederlands - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info