572515
6
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
SD-860
2
Introduction
READ THIS BEFORE OPERATING YOUR UNIT
: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
FCC INFORMATION(FOR U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION : Any changes or modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
CAUTION
Invisible laser radiation when the unit is open.
Do not stare into beam.
CAUTION : USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION
WARNING
: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
This symbol is intended to alert the user to the
presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CLASS 1
LASER PRODUCT
3
1. Read Instructions - All the safety and operating instructions should
be read before the product is operated.
2. Retain instructions - The safety and operating instructions should
be retained for future reference.
3. Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be
followed.
5. Cleaning - Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6. Attachments - Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in
a wet basement, or near a swimming pool; and the like.
8. Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use only with
a cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting of the product
should follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9. A product and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the product
and cart combination to overturn.
10. Ventilation - Slots and openings in the
cabinet are provided for ventilation and to
ensure reliable operation of the product and
to protect it from overheating, and these
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been adhered to.
11. Power Sources - This product should be operated only from the
type of power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult your product
dealer or local power company. For products intended to operate
from battery power, or other sources, refer to the operating
instructions.
12. Grounding or Polarization - This product may be equipped with a
polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail
to fit, contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third(grounding) pin. This plug
will only fit into a grounding-type power outlet. this is a safety
feature. If you are unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.
13. Power-Cord Protection - Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the
product.
14. Outdoor Antenna Grounding - If an outside antenna or cable
system is connected to the product, be sure the antenna or cable
system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with
regard to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for the
grounding electrode. See Figure 1.
15. Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the product due to
lightning and power-line surges.
16. Power Lines - An outside antenna system should not be located in
the vicinity of overhead power lines or other electric light or power
circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken
to keep from touching such power lines or circuits as contact with
them might be fatal.
17. Overloading - Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire
or electric shock.
18. Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
19. Servicing - Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service - Unplug this product form the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to
its normal operation.
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
21. Replacement Parts - When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
22. Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting - The product should be mounted to a
wall or ceiling only as recommended by the manufacturer.
24. Heat - The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
Notes:
1. Item 12 is not required except for grounded or polarized product.
2. Item 14 and 16 are not required except for units provided with
antenna terminals.
3. Item 14 complies with UL in U.S.A.
PORTABLE CART WARNING
Figure 1
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
GROUND CLAMPS
SAFETY INSTRUCTIONS
PRECAUTIONS
FOR YOUR SAFETY
4
Units shipped to the U.S.A and Canada are designed for operation on 120 V AC only.
Safety precaution with use of a polarized AC plug.
However, some products may be supplied with a nonpolarized plug.
CAUTION
: To prevent electric shock, match wide blade of plug to wide slot, fully
insert.
ATTENTION
: Pour éviter chocs électriques, introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et pousser jusqu au fond.
The available power supply voltage differs according to country or region. However,
this unit is equipped with an Automatic Voltage Selector.
The power supply voltage of the area where the unit will be used automatically
meets the required voltage within the range of AC 220 - 240 V, without any manual
voltage adjustment.
To ensure safe operation, the three-pin plug supplied must be inserted only into a
standard three-pin power point which is effectively earthed through the normal
household wiring. Extension cords used with the equipment must be three-core and
be correctly wired to provide connection to earth.
Improper extension cords are a major cause of fatalities. The fact that the equipment
operates satisfactorily does not imply that the power point is earthed and that the
installation is completely safe. For your safety, if in any doubt about the effective
earthing of the power point, consult a qualified electrician.
U.S.A
and
CANADA
CHINA,
EUROPE,
AUSTRALIA
and other
countries
120 V
220 V
-
240 V
󳂮Moisture condensation
Moisture may form on the lens in the following conditions.
Immediately after a heater has been turned on.
In a steamy or very humid room.
When this unit is moved from a cold place to a warm one.
If moisture forms inside this unit, it may not operate properly.
In this case, turn on the power and wait about one hour for the moisture to evaporate.
󳂮If there is noise interference on the TV while a broadcast is being received.
Depending on the reception condition of the TV, interference may appear on the TV screen while you are
watching a TV broadcast and this unit is left on. This is not a malfunction of this unit or the TV. To watch a TV
broadcast, turn off this unit.
󳂮Do not transport this unit with discs left in it.
󳂮Do not place on the component such as amplifier or receiver that generates heat.
If so, the temperature inside this unit rises and malfunction may occur.
CAUTION
Leave a space around the unit for sufficient ventilation.
Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating
equipment.
Keep the unit free from moisture, water, and dust.
Do not let foreign objects in the unit.
The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers,
table-cloths, curtains, etc.
No naked flame sources, such as lighted candles, should be placed on the unit.
Please be care the environmental aspects of battery disposal.
The unit shall not be exposed to dripping or splashing for use.
No objects filled with liquids, such as vases, shall be placed on the unit.
Do not let insecticides, benzene, and thinner come in contact with the set.
Never disassemble or modify the unit in any way.
󳂮Notes on the AC power cord.
The unit is not disconnected from the AC power source(mains) as long as it is connected to the wall outlet,
even if the unit has been turned off.
When disconnecting the power cord from the wall outlet, always pull the plug, not the power cord.
Disconnect the plug from the wall outlet when not using the unit for long periods of time.
• Introduction
READ THIS BEFORE OPERATING YOUR UNIT | 2
• System Connections
CONNECTING TO A/V AMPLIFIER OR RECEIVER | 6
CONNECTING TO TV WITH AUDIO AND VIDEO INS | 9
CONNECTING TO TV WITH SCART CONNECTOR(Regional Option) | 9
• Front Panel & Remote Controls | 10
REMOTE CONTROL OPERATION RANGE | 11
LOADING BATTERIES | 11
• Preliminary Knowledge About Discs
PLAYABLE DISC TYPES | 12
REGION CODE | 12
NOTES ON COPYRIGHT | 12
SYMBOL ABOUT INVALID OPERATION | 12
AUDIO AND VIDEO FILES | 13
CARE AND HANDLING OF DISCS | 13
• Operations
BASIC PLAYBACK | 14
DISPLAYING DISC INFORMATION DURING PLAYBACK | 20
PLAYING THE DESIRED SECTION OF DISC | 21
PLAYING A SPECIFIC ITEM | 22
REPEAT PLAYBACK | 23
PLAYING TRACKS/FILES IN RANDOM ORDER | 24
PLAYING TRACKS IN DESIRED ORDER | 25
BOOKMARK PLAYBACK | 26
CHANGING THE AUDIO LANGUAGE | 27
CHANGING THE SUBTITLE LANGUAGE | 27
CHANGING THE CAMERA ANGLE | 28
ZOOMING IN/OUT A SCENE | 28
CHANGING THE VIDEO SIGNAL FORMAT | 29
CHANGING THE COMPONENT VIDEO OUTPUT SIGNAL | 29
• Initial Settings | 30
SETTING THE LANGUAGE SETUP | 31
SETTING THE VIDEO SETUP | 33
SETTING THE AUDIO SETUP | 36
SETTING THE SPEAKER SETUP | 38
SETTING THE OTHER SETUP | 43
• Definition Of Terms | 49
• Troubleshooting Guide | 51
• Specifications | 52
• DVD Language Code List | 53
5
CONTENTS
6
System Connections
Do not connect the AC input cord into the AC outlet when plugging and unplugging connection cords.
Since different components often have different terminal names, carefully read the operating instructions of the component
connected.
Be sure to observe the color coding when connecting audio and video cords.
The supplied cords are a (stereo) audio cord, a composite video cord, a system control cord and a power cord. Other cords
are commercially-available cords.
5.1 CH AUDIO IN
L R
FRONT
L R
SURROUND
CENTER SUB-
WOOFER
L R
AUDIO IN
OPTICAL
DIGITAL INs
COAXIAL S-VIDEO
IN
(COMPOSITE)
VIDEO IN
Y Cb/Pb Cr/Pr
COMPONENT
VIDEO IN
(MONITOR)
VIDEO OUT
COMPONENT, S-VIDEO, COMPOSITE
FRONT L/R, CENTER, SURROUND L/R, SUBWOOFER, etc.
VIDEO IN
SPEAKERS
A/V Amplifier or Receiver
TV
(COMPOSITE)
VIDEO IN
S-VIDEO IN
Additional TV, etc.
Speakers
CONNECTING TO A/V AMPLIFIER OR RECEIVER
When your amplifier/receiver is not compatible with the
digital signals that are output from this unit, loud noise or no
sound may be heard from the speakers, and it may be
harmful to your ears and damages the speakers. To
prevent it, you should set the DIGITAL OUTPUT to OFF
and make analog audio connections. (Refer to When
selecting the DIGITAL OUTPUT on page 36.)
When making the COAXIAL DIGITAL connection, be sure
to use a 75 COAXIAL cord, not a conventional AUDIO
cord.
All of the commercially-available optical fiber cords cannot
be used for audio equipments. If there is an optical fiber
cord which cannot be connected to your audio equipments,
consult your dealer or nearest service organization.
󳂮Audio output from the units DIGITAL OUTPUTs
When the DIGITAL OUTPUT is set to ON, the following
table shows that the digital signals can be output from the
DIGITAL OUTPUTs.(For details, refer to When selecting
the DIGITAL OUTPUT on page 36.)
Disc type Audio recording format Audio output
Dolby Digital Dolby Digital bitstream
DVD Video
DTS DTS bitstream
Linear PCM 48kHz/16~24bit 48kHz/16~24bit PCM
96kHz/16~24bit 96kHz/16~24bit PCM
DVD Audio Linear PCM or Packed PCM
-
DSD (SACD Area)
-
SACD 44.1kHz/16bit Linear PCM 44.1kHz/16bit PCM
(CD Area)
Audio CD 44.1kHz/16bit Linear PCM 44.1kHz/16bit PCM
MP3 disc MP3 44.1, 48kHz/16bit PCM
WMA disc WMA 44.1, 48kHz/16bit PCM
DivX disc MP3 44.1, 48kHz/16bit PCM
7
1. Connecting 5.1CH AUDIO OUTPUTs
To fully enjoy the multichannel audio of DVD Audio and
SACD as well as Dolby Digital and DTS soundtracks of
DVD Video, etc., connect these jacks to the corresponding
channel input jacks of your amplifier/receiver.
Notes :
When connecting only the 5.1CH AUDIO OUTPUTs to your
amplifier/receiver, you should set the DOWNMIX to OFF to
output the multichannel audio signals from these jacks as it
was recorded.
In this case, only the front left and right signals of the
multichannel audio signals will output from the 2CH AUDIO
OUTPUT jacks (and the A/V SCART OUTPUT connector).
(For details, refer to When selecting the DOWNMIX on
page 36.)
When connecting the 5.1CH AUDIO OUTPUTs to the
multichannel audio inputs of an amplifier/receiver that dose
not have the speaker setup for the multichannel audio
inputs, you should set the SPEAKER SETUP.(For details,
refer to SETTING THE SPEAKER SETUP on page 38.)
2. Connecting 2CH AUDIO OUTPUTs
Connect these jacks to the AUDIO IN jacks of DVD(, AUX,
CD, etc.) of your amplifier/receiver.
Depending on whether these jacks to a stereo amplifier /
receiver or an A/V amplifier/receiver with built-in surround
decoder, you should set the DOWNMIX to Lo/Ro or
Lt/Rt.(For details, refer to When selecting the DOWNMIX
on page 36.)
3. Connecting DIGITAL OUTPUTs
To enhance the sound quality, connect either the OPTICAL
or the COAXIAL DIGITAL OUTPUT jack to the
corresponding DIGITAL INPUT jack of your
amplifier/receiver with built-in Dolby Digital or DTS decoder.
(You dont need to do both.)
When DVD Video, etc. recorded in Dolby Digital or DTS is
played, you can enjoy high-quality surround sound.
To be output digital audio signals from the DIGITAL
OUTPUT jacks, you should set the DIGITAL OUTPUT to
ON. (For details, refer to When selecting the DIGITAL
OUTPUTon page 36)
Notes :
The DIGITAL OUTPUT jacks cannot output the digital
audio signals of DVD Audio and SACD.
Therefore, to be able to play multichannel DVD Audios and
SACDs, you should also connect the 5.1CH AUDIO
OUTPUTs.(Refer to Connecting 5.1CH AUDIO
OUTPUTs above)
If your amplifier/receiver doesnt have 5.1CH AUDIO
INPUTs, make a stereo analog connection . (Refer to
Connecting 2CH AUDIO OUTPUTs above.)
In order to be able to hear multichannel sound from DVD
Audio and SACD, you should set DVD AUDIO AREA to
DVD AUDIO and SACD AREA to MULTICHANNEL.(Refer
to When selecting the DVD AUDIO AREA and When
selecting the SACD AREA on page 44.)
It is not recommended to record digital audio signals with
digital audio connection between this unit and MD or CD
recorder, etc.
When recording the sounds played on this unit, record them
through the 2CH AUDIO OUTPUT jacks.
4. Connecting COMPOSITE VIDEO OUTPUTs 1, 2
Connect this jack to the (composite)VIDEO input jack of
your amplifier/receiver or TV.
The same signal is output from COMPOSITE VIDEO
OUTPUT 1 and 2 jacks, enabling connection to two
devices(e, g., an A/V amplifier and additional TV)
simultaneously.
5. Connecting S-VIDEO OUTPUTs 1, 2
Connect this jack to the S-VIDEO input jack of your
amplifier/receiver or TV
The same signal is output from S-VIDEO OUTPUT 1 and 2
jacks, enabling connection to two devices(e, g., an A/V
amplifier and additional TV) simultaneously.
6. Connecting COMPONENT VIDEO OUTPUTs
The COMPONENT VIDEO OUTPUTs of this unit are capable
of outputting either conventional interlacing video signal or
progressively scanned video signal(that can reproduce high-
density pictures with less flicker).
According to VIDEO OUTPUTs, the excellence in picture
quality is as follows:
Progressive COMPONENT > Interlaced COMPONENT
> S-VIDEO > COMPOSITE
When making COMPONENT VIDEO connections, connect
Y to Y, P
b to Pb(, Cb, B-Y), Pr to Pr (, Cr, R-Y).
Notes:
When the VIDEO OUTPUT is set to PROGRESSIVE, the
S-VIDEO and COMPOSITE VIDEO OUTPUTs can not
output the video signals, meaning the picture will not be
shown.
When the progressive video signals are input into the non-
progressive COMPONENT VIDEO INPUTs of your TV, the
picture may not be shown normally.
Therefore, when the progressive COMPONENT VIDEO
INPUTs of TV are not connected to, you should set the
VIDEO OUTPUT to INTERLACED.(For details, refer to
When selecting the VIDEO OUTPUT on page 34.)
Do not connect the unit to the TV through a VCR.
Otherwise the picture may be disturbed due to the copy
protection function.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE STANDARD
DEFINITION OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.
7. Connecting DIGI-LINK jack
Connect this jack to the DIGI LINK jack of the external
Sherwood component that uses the DIGI LINK II or III
remote control system.
8. A/V SCART OUTPUT CONNECTOR(Regional Option)
Refer to CONNECTING TO TV WITH SCART
CONNECTOR (Regional Option) on next page.
9. AC INPUT
Plug the supplied power cord into this AC INPUT and then
into the wall AC outlet.
8
System
control
cord
Sherwood component
with DIGI LINK II or III
Amplifier/receiver
Tape deck
CD player
9
A/V SCART IN
This unit
TV
For some countries like Europe, the unit incorporates the A/V SCART OUTPUT connector.
You can connect the unit to TV easily using the SCART connections without other cumbersome audio and video connections.
During operation of the unit, this connector can deliver either the composite(regular) video, S-VIDEO (Y and C) or RGB video
signals as well as the audio L and R signals.
Notes:
In this connection, do not connect the unit to the TV through a VCR. Otherwise the image may be disturbed due to the copy
protection function.
According to the video connections between this unit and TV, etc. and the video input source selected on TV, etc., be sure to
set the SCART VIDEO and the VIDEO OUTPUT to the corresponding settings.
When these are not set correctly, no picture or abnormal picture may be displayed.(For details, refer to When selecting the
VIDEO OUTPUT and When selecting the SCART VIDEO(Regional Option) on page 34.)
CONNECTING TO TV WITH SCART CONNECTOR(Regional Option)
You can enjoy DVD Videos by simply connecting this unit to a TV. To hear improved audio sound quality, connect the 2CH
AUDIO OUTPUTs to the AUDIO INs of DVD(, AUX, CD, etc.) of your amplifier/receiver.
To connect these jacks correctly, refer to Connecting 2CH AUDIO OUTPUTs on page 7, Connecting COMPOSITE VIDEO
OUTPUTs 1, 2 and so forth on page 8.
Notes:
If your TV has a monaural audio input instead of stereo, you need to use an optional audio cord which converts stereo audio
output to monaural.
Do not connect the VIDEO OUTs of the unit to the TV through a VCR. Otherwise the image may be disturbed due to the
copy protection function.
CONNECTING TO TV WITH AUDIO AND VIDEO INS
L
R
AUDIO
IN
L
R
AUDIO
IN
Amplifier or Receiver
This unit
S-VIDEO
IN
(COMPOSITE)
VIDEO IN
COMPONENT
VIDEO IN
Y Cb/Pb Cr/Pr
TV, projector, etc.
Front Panel & Remote Controls
1. POWER ON button
2. STANDBY button
3. OPEN/CLOSE(
󳂮
) button
4. DIMMER button
5. DISPLAY button
6. NTSC/PAL button
7. UPSCALE button
8. SEARCH button
9. MARKER button
10. NUMERIC (0~9, +10) buttons
11. CLEAR button
12. REPEAT( ) button
13. REPEAT A/B button
14. PROGRAM button
15. RANDOM PLAY button
16. AUDIO button
17. SUBTITLE button
18. ZOOM button
19. ANGLE button
20. SACD AREA button
21. PURE AUDIO button
22. TOP MENU button
23. MENU button
24. CURSOR CONTROL(///), ENTER buttons
25. SETUP button
26. RETURN button
27. STOP button
28. PLAY button
29. PAUSE/STEP button
30. SCAN / buttons
31. SKIP
󳂮
/
󳂮
buttons
32. PAGE / buttons
33. TITLE/GROUP / buttons
1. POWER switch
2. STANDBY indicator
3. FORWARD/BACKWARD SKIP
(
󳂮
/
󳂮
) buttons
4. STOP(󳂮) button
5. PAUSE/STEP(
󳂮󳂮
) button
6. PLAY() button
7. OPEN/CLOSE(
󳂮
) button
8. DISC TRAY
9. SACD indicator
10. DVD AUDIO indicator
11. PURE AUDIO indicator
12. REMOTE SENSOR
13. FLUORESCENT DISPLAY
For details, see next page.
10
Front Panel Controls
Remote Controls
11
Fluorescent Display
AUDIO FILE TYPE indicators
CHANNEL indicators
PLAY Indicator
DISC TYPE
indicators
SOUND RECORDING SYSTEM
indicators
PROGRESSIVE indicator
PURE AUDIO indicators
VIDEO FILE TYPE
indicators
SOUND RECORDING SYSTEM
indicators
PAUSE
indicator
REMAIN indicator
ANGLE indicator
REPEAT indicators
Group/title number,
track/chapter number,
playing time, operating
information, etc.
RANDOM indicator
PROGRAM indicator
SOUND RECORDING
SYSTEM indicator
REMOTE CONTROL OPERATION RANGE
Use the remote control unit within a range of about
7 meters (23 feet) and angles of up to 30 degrees
aiming at the remote sensor.
Note:
Remote operation may become unreliable if the
REMOTE SENSOR is exposed to strong light
such as direct sunlight or inverted fluorescent.
LOADING BATTERIES
1
Remove the cover.
2
Load two batteries (AAA size, 1.5V)
matching the polarity.
Remove the batteries when they are not used for a
long time.
Do not use the rechargeable batteries(Ni-Cd type).
DVD players and DVD Videos have their own Region Code
numbers which are assigned to each country or area as
shown below. DVD players are set to your Region Code
number at the factory. As a result, if the region code
number of this DVD player is different from that of the DVD
Video, playback of the DVD Video will not be allowed by
the DVD player.
Examples of playable DVD Videos :
In U.S.A. In Europe
12
Please check the copyright laws in your country to record
from DVD, Audio CD, MP3, WMA, JPEG and DivX discs, etc.
Recording of copyrighted material may infringe copyright
laws.
Commercial DVD Video discs are copy-protected, and any
recordings made from these discs will be distorted.
This product incorporates copyright protection technology
that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology
must be authorized by Macrovision, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
Preliminary Knowledge About Discs
PLAYABLE DISC TYPES REGION CODE
NOTES ON COPYRIGHT
This unit supports the following discs.
This unit supports CD-R and CD-RW discs recorded in
audio CD format or MP3/WMA/JPEG/DivX in accordance
with the ISO9660 format. It also supports DVD-R, DVD-
RW, DVD+R and DVD+RW discs recorded in DVD Video
format or DivX in accordance with UDF format.
󳂮Unplayable discs
Since this unit cannot support disc types, formats and file
types not listed above, do not play such discs.
Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs or CD-
Rs/CD-RWs cannot be played due to incomplete disc
finalization, recording quality or physical condition of the
disc, characteristics of recording device or authoring
software, etc.
See the operating instructions supplied with your recording
device for more information.
󳂮Color system format
Depending on the countries, this unit conforms to either the
NTSC color system for U.S.A, Canada, etc. or the PAL for
Europe, Australia, China, etc.
Major
countries
or area
Playable
Region
code
All
regions
North
America
Europe,
Japan,
Middle East
Southeast
Asia
Oceania,
South
America
Russia
China
SYMBOL ABOUT INVALID OPERATION
When you press a button, if the unit does not accept its
operation, appears on the TV screen.
Operations are occasionally unacceptable even if is
not displayed.
Invalid operation may occur as expected if :
The region code number of the unit is different from that of
the DVD Video and playback will not be allowed.
The rating level function works.
(For details, refer to When selecting the PARENTAL
CONTROL on page 45.)
A disc is not playable or uses features that are not
supported by this unit.
Disc Logo Format or file type
DVD Video
DVD Audio
SACD
DVD-R
DVD-RW
DVD+R
DVD+RW
Audio CD
CD-R
CD-RW
JPEG CD
MP3 CD
DVD Video
DVD Audio
Super Audio CD
(Single layer, Dual layer,
Hybrid)
DVD Video, DivX
DVD Video, DivX
DVD Video, DivX
DVD Video, DivX
PCM
Audio CD, MP3, WMA,
JPEG, DivX
Audio CD, MP3, WMA,
JPEG, DivX
JPEG
MP3
13
In handling a disc, hold it carefully
with edges.
Do not stick paper or write
anything on the printed surface.
Fingermarks and dust on the
recorded surface should be
carefully wiped off with a soft cloth.
Wipe straight from the inside to the
outside of the disc.
Always keep the discs in their
cases after use to protect them
from dust and scratches.
Do not use a cracked, deformed, or repaired disc.
These discs are easily broken and may cause serious
personal injury and apparatus malfunction.
Notes:
Because the temperature inside this unit is very high, in
case of no further playback of disc, unload the disc to
prevent the high temperature from deforming the disc.
Do not expose discs to direct sunlight, high humidity or
high temperature for a long time.
When loading or unloading a disc in the disc tray, always
place it with the printed side up.
AUDIO AND VIDEO FILES CARE AND HANDLING OF DISCS
Folder and file names are displayed up to 11 characters.
Characters except A~Z, 0~9, - may be not displayed.
The playback order of folders and files shown in the menu
may differ from the order shown in a PC.
This unit supports multi-session discs. Some multi-session
discs may take a long time to load and some may not be
loaded at all.
󳂮Notes for making a private disc.
Use UDF format as the disc format for DVD-R/DVD-RW,
DVD+R/DVD+RW.
Use ISO 9660 as the disc format for CD-R/CD-RW.
Folders can be up to eight levels deep.
Some disc may not play due to disc characteristics,
recording conditions, etc.
󳂮MP3
MP3 files must have a .mp3 or .MP3 file name
extension.
It is recommended that you record your material at a
44.1kHz sampling rate, using the 128 kbps data transfer
rate.
Fixed bit-rate files are recommended. Variable bit-
rate(VBR) files are playable, but playing time may be
displayed incorrectly.
ID3 Tag is not available.
MP3i and MP3 Pro are not available.
󳂮JPEG
JPEG files must have a .jpg, .JPG, .jpeg or .JPEG
file name extension.
It is recommended that you record your material at a
640X480 pixel resolution.
This unit cannot play a baseline JPEG file of more than
6000X4500 pixels and a progressive JPEG file of more
than 5120X3840 pixels.
󳂮DivX
DivX files must have a .divx, .DIVX, .div, .DIV, .avi
or .AVI file name extension.
This unit supports DivX 5.x, 4.x and 3.11
This unit supports DivX files whose resolution is 640X480
pixels or less.
Audio stream supports MPEG Audio Layer 3(MP3), WMA
or AC-3, etc..
This unit does not support GMC(Global Motion
Compression) and Q-Pel(Quarter Pixel).
This unit has its own Registration Code for DivX playback.
If necessary, you can confirm the registration code of your
unit.(For details, refer to When selecting the DIVX VOD
on page 47.)
󳂮WMA
WMA files must have a .wma or .WMA file name extension.
It is recommended that you record your material at a bit
rate of 64 kbps or higher.
WMA Tag is not available.
This unit cannot play copyright protected files and files
recorded with a bit rate under 32kbps.
Printed side
14
BASIC PLAYBACK
Operations
Before operation, enter the standby mode.
1
The STANDBY indicator lights up in amber. This means
that the unit is connected to the AC mains and a small
amount of current is retained to support operational
readiness.
To turn the power completely off, press the POWER
switch again.
Press the POWER ON button, then the unit is turned on
to enter the operating mode and the STANDBY indicator
lights up in blue.
In the operating mode, to enter the standby mode, press
the STANDBY button.
8 cm (3 inch) discs can be loaded on the inside circle of
the tray, too.
When a DVD that doesnt contain any menu is loaded,
playback automatically starts.
In the standby mode, turn the power on.
2
Open the disc tray to load a disc with the printed side up,
then close it.
3
Notes :
In case of DVD Audios, when the DVD Audio to be played contains not only DVD Audio content but also DVD Video content,
first be sure to set the DVD AUDIO AREA correctly before playback.(For details, refer to When selecting the DVD AUDIO
AREA on page 44.)
In case of SACDs, when the SACD to be played contains 2 channel and multichannel audio areas, and CD layer, first be sure
to select the preferred area/layer before playback.(For details, refer to To select a playback area/layer on page 16.)
In case of DivX discs, this unit provides you the DivX
®
VOD(Video On Demand) registration code that allows you to rent and
purchase videos from DivX
®
VOD service at www.divx.com/vod.
If necessary, you can confirm the registration code of your unit. (For details, refer to When selecting the DIVX VOD on page
47.)
Depending on the disc types, it may take times to read the loaded disc.
󳂮Before starting playback
Make the initial settings to suit your usage conditions the very first time this unit is turned on.(For details, refer to Initial
Settings on page 30)
For explanation purposes, this instructions explains the OSD(On-Screen Display) language displayed on TV in English.
Usable discs for each operation/ function are referred to by the icons;
󳂮Preparations
Turn on the TV and select the video input source connected to the unit.
When you want to enjoy the sound of disc from the audio system, turn on the audio system and select the input source
connected to the unit.
Main unit
RC
Main unit
RC
or
󳂮In case of use of the NUMERIC buttons on the
remote control :
When selecting 3 :
When selecting 10 :
When selecting 21 :
15
Playback of the selected item starts.
In case of selecting the item with pressing the NUMERIC buttons, depending on the discs, the PLAY()(or ENTER) button
should be pressed to start playback of the item.
Depending on the discs, the preferred item may not be selected with pressing the NUMERIC buttons.
When the selected item contains the subitems, repeat the above step until the preferred item is selected.
󳂮To stop playback and return to the menu display
Press the TOP MENU or MENU button on the remote control.(Which button is pressed differs depending on the discs.)
Playback is suspended and the menu display appears.
To start playback from the menu of DVD
To select the preferred item, press the CURSOR ▲/▼/◀/▶ buttons and press the ENTER button (or PLAY() button), or
press the NUMERIC buttons.
When a SACD contains the information on track,
album and artist, etc., the corresponding information
will be displayed or not on the TV screen depending
on the OSD setting.(For details, refer to When
selecting the OSD on page 44.)
RCRC
In case of SACD or CD, press the PLAY()
button to start play.
4
TITLE MENU
Dogs
Cats
Cows
Horses
ROOT
ROOT 0
POPS 1
BLUES 2
HAPPY 3
SO LONG 4
CLASSIC 5
LIGHT-M 6
BIRTHDAY 7
MP3 file symbol
Folder symbol
Root menu
SMART NAVI
Folder and file menu
Main unit
RC
or
When you load a MP3, WMA, JPEG, DivX disc or a DVD that contains a menu, the menu display may appear on the TV
screen. In this case, see To start playback from the menu of DVD below or To start playback from the menu of MP3,
WMA, JPEG or DivX disc on the next page.
Example of DVD Video Example of MP3 disc
16
Notes:
To play a MP3/WMA/JPEG/DivX disc with the various playback modes, select the desired playback mode.(For details, refer to
Repeating a file, folder on page 23.)
Some discs/files recorded in DVD Video, MP3, WMA, JPEG or DivX, etc. cannot be played due to incomplete disc finalization,
recording quality or physical condition of the disc, characteristics of recording device or authoring software, etc.
The DVDs continue to rotate while the menu display appears. When no further selections are to be played, be sure to press
the STOP(󳂮) button repeatedly to enter the stop mode and to clear the menu display.
A TV screen may be burned out if a static picture is displayed for a long time in the stop mode. To prevent this, set the
SCREEN SAVER to ON (refer to When selecting the SCREEN SAVER on page 43). Then, the unit automatically activates
the screen saver function if a static picture, etc. is displayed for over 5 minutes.
Pressing any button will cancel the screen saver function and return to the previous display.
When you press a button, if the corresponding operation is prohibited by the unit or the disc, appears on your TV screen.
When selecting the preferred file, playback starts from the
selected file.
When selecting the preferred folder, the file menu screen
of the selected folder is displayed. In this case, repeat this
step to select the preferred file in its file menu.
Press the CURSOR / buttons to select the preferred folder or file then press the ENTER button.
2
RCRC
To select a playback area / layer
Some SACDs consist of 2 channel and multichannel audio areas, and hybrid SACDs comprise 2 layer structure of an
HD(SACD) layer and CD layer. You can select the desired area/layer to be played. (For details, see the discs sleeve notes.)
This operation works only with SACDs on which 2 areas or/and 2 layers are recorded.
Therefore, when the disc does not contain the preferred channel area or CD layer, you cannot select it.
You can set the SACD area to the desired at initial settings, too.(For details, refer to When selecting the SACD AREA on
page 44.)
In the stop mode
Each time this button is pressed, the playback area/layer changes and is
displayed on the TV screen for several seconds as follows :
󳂵 MULTI CHANNEL MODE : When playing the multichannel area(of HD layer.)
󳂸
TWO CHANNEL MODE : When playing the 2 channel area(of HD layer.)
󳂸
CD LAYER : When playing the CD layer.
After selecting the preferred area or the CD layer, press the PLAY() button
to play the selected.
Each time the layer changes from HD(SACD) layer to CD layer and vice
versa, it takes several seconds and CHANGE LAYER is displayed.
RC
In the stop mode, press the CURSOR / buttons to select the folder and file menu.
1
To start playback from the menu of MP3, WMA, JPEG or DivX disc
RC
17
To stop playback
When playback of a DVD is stopped, the unit memorizes
the point where the STOP(󳂮) button was
pressed(RESUME function: DVD only).
(RESUME is displayed on the units display when this
function is activated.)
Press the PLAY() button again, and playback will resume
from this point. When the STOP(󳂮) button is pressed
again, the RESUME function will be canceled and it enters
stop mode.(STOP is displayed.)
During playback of a DVD, when the unit is turned off and
on with pressing the STANDBY button and the POWER ON
button, the resume function is activated, too.
DVD Video :
The unit will be in the still picture mode.
In case of DVD Audio, it can be in the still picture mode only
for the video part.
DVD Audio/SACD/CD/MP3/WMA/JPEG/DivX disc :
The unit will be in the pause mode.
To return to normal playback, press the PLAY() button.
Each time the PAUSE/STEP(
󳂮󳂮
) button is pressed, the disc
is advanced by one frame.
In case of DVD Audio, the frame advance playback is
possible only for the video part.
To return to normal playback, press the PLAY() button.
Each time the button is pressed, a title/ group is skipped.
Main unit
RC
or
To pause playback
Main unit
RC
or
In the still picture mode,
Frame advance playback
Main unit
RC
or
To select a title/group during playback
When some DVDs contain more than one title/group, you
can select the desired one.
RC
To skip
back
To skip
ahead
18
Rapid playback during playback
Slow playback
To select a page during playback
Each time the button is pressed, the disc is advanced or
reversed fast at up to 6 step speeds depending on the disc
types.
2X 4X 6X 8X Off
(normal playback)
2X 4X 8X 16X Off(normal playback)
2X 4X 8X 16X 32X 64X Off(normal playback)
To return to normal playback, press the PLAY() button.
Each time the button is pressed, the disc is advanced or
reversed slowly at 3 step speed.
1/2 X 1/4 X 1/8 X Off
(normal playback)
In case of DVD Audio, the slow playback is possible only
for the video part.
To return to normal playback, press the PLAY() button.
Each time the button is pressed, the page is changed and
displayed on the TV screen.
Depending on the disc, the information pages may not be
selected.
Each time the button is pressed, a chapter/track/file is skipped.
In case of DVD, SACD and CD, when the BACKWARD
SKIP button is pressed once midway through a
chapter/track, playback returns to the beginning of that
chapter/track. When it is pressed again, a chapter/ track is
skipped.
You can select a chapter/track/file directly with pressing the
NUMERIC buttons on the remote control.
Examples) For 3 :
For 10 :
For 21 :
In case of selecting a file, you can select a file in the
current folder only.
In case of JPEG/DivX disc, you can select a file in the stop
mode only.
Depending on the discs, the desired one may not be
selected.
You can play back discs at various speeds.
In the still picture mode, you can play back the discs at
various speeds.
RC
To reverse To advance
RC
To reverse To advance
When some DVD Audios contain the information pages
that can include photo galleries, artist biographies, lyrics,
etc., you can select the desired page.
RC
To skip ahead or back during playback
To skip ahead To skip back
Main unit
RC
or
Main unit
RC
or
19
Bonus group playback
Some DVD Audios contain an extra bonus group that requires a 4-digit password to access.(For details on 4-digit password,
see the discs sleeve notes.)
RC
BONUS GROUP INPUT PW:
Achieving higher purity of sound quality
Each time the PURE AUDIO button is pressed, the pure
audio mode changes and the corresponding indicator
lights up on the units display as follows :
󳂵
PURE DIGITAL lights up: When turning off all the video-related
circuits to enjoy pure digital audio.
󳂸
PURE ANALOG lights up: When turning off all the video-related
circuits and the digital audio-related
circuits to enjoy pure analog audio.
󳂸
OFF: When turning off the pure audio function.
Each time the DIMMER button is pressed, the brightness
of the fluorescent display of this unit changes as follows:
ON dimmer OFF
In the display OFF mode, pressing any button will restore
the display ON mode.
You can turn off all the video-related circuits as well as the digital audio-related circuits to eliminate the possibility of
interference for a pure audio experience when playing audio-only discs.
Although intended for use with audio discs, this function can also be used to enjoy soundtracks and music on DVD Videos
and DivX discs.
RC
RC
During playback, select the bonus group.
1
Then password input screen is displayed.
Depending on DVD Audios, you can select the bonus
group on the title or DVD menu, too.
Depending on the disc, the bonus group operation may
vary.
Then the bonus group will be played.
If you input a wrong password, do it again.
Input the 4-digit password with pressing the NUMERIC
buttons.
Example) When inputting 1011
2
Adjusting the brightness of the fluorescent display
RC
20
DISPLAYING DISC INFORMATION DURING PLAYBACK
The unit features the on-screen display function showing disc information.
Press the DISPLAY button.
Then the disc information is displayed on the TV screen.
Each time this button is pressed, the disc information is changed depending on the disc types as follows :
RC
TITLE 01/07 CHAPTER 001/012
TITLE ELAPSED
00:16:25
TITLE REMAIN
01:37:32
CHAPTER ELAPSED
00:00:17
CHAPTER REMAIN
00:01:55
: Title/chapter number
or group/track number
: Elapsed time of
the title/group
: Remaining time of
the title/group
: Elapsed time of
the chapter/track
: Remaining time of
the chapter/track
: Audio/subtitle language
TRACK ELAPSED
00:22
TRACK REMAIN
02:01
TOTAL ELAPSED
00:22
TOTAL REMAIN
70:16
OFF
OFF
: Elapsed time of
the track
: Remaining time of
the track
: Elapsed time of
the disc
: Remaining time of
the disc
FILE ELAPSED 00:00:34
FILE REMAIN 00:04:25
: Elapsed time of
the file
: Remaining time of
the file
Total title/group
number
Current title/group
number
OFF
Total chapter/track number
Current chapter/track number
AUDIO 1/3 : D 5.1 ENGLISH
SUBTITLE 01/02 : ENGLISH
Depending on the disc and some operation status as playback of DVD using a title or DVD menu, etc., the disc information
may not be displayed.
󳂮To display additional information on a file
In the stop mode, press the DISPLAY button after selecting the desired file.
Then the information on file size, recording conditions, etc. will be displayed.
To turn off the information, press this button again.
RC
21
PLAYING THE DESIRED SECTION OF DISC
1
During playback, press the SEARCH button.
2
Select the section to be played with pressing the NUMERIC buttons on the remote control.
3
Start playback from the selected section.
󳂮When entering title, chapter, group, track number
Examples) For 3 :
For 11 :
󳂮When clearing the numbers entered before playback
Press the CLEAR button.
Then the numbers are all cleared.
󳂮When entering the elapsed time
You can play a disc from the desired point by specifying the
elapsed time from the beginning of the current title/group/file.
Examples) For 3 min. 15 sec. :
For 2 hou. 59 min. 35 sec. :
Notes :
If the title/group/chapter/track/time you entered is not
contained on the disc, search playback will not work.
Depending on the disc, a search playback will not work or
may work differently.
The selected mode is highlighted.
Then the search mode is displayed on the TV screen.
Each time this button is pressed, the search mode is
changed depending on the disc types as follows:
󳂮When selecting the desired search mode while displaying title/chapter, group/track, title/time or group/time search mode.
Press the CURSOR / buttons to select the desired search mode.
TITLE 01/07 CHAPTER 001 / 012
Total chapter/track number
Current chapter/track number
Total title/group
number
Current title/
group number
: Title/chapter search mode
or group/track search mode
TIME
--
:
--
:
--
: Time search mode
TITLE 01/07 TIME
--
:
--
:
--
: Title/time search mode
or group/time search mode
OFF
OFF
RC
RC
RC
Main unit
RC
RC
oror
22
During playback, press the TOP MENU button.
1
Press the CURSOR /// buttons to select the desired title, then press the ENTER or PLAY() button.
2
When using a title menu
If some DVDs which contain more than one title may have the menu like as a list of the titles, the TOP MENU button can be
used to select the desired title. (The details of operation differ depending on the disc used.)
Then a list of titles on the disc is displayed on TV screen.
If the disc does not have the menu such as a list of titles,
this function does not work.
The unit starts playback of the selected title.
When the menu continues onto another screen, repeat
this step until the desired title is selected.
PLAYING A SPECIFIC ITEM
During playback, press the MENU button.
1
Press the CURSOR /// buttons to select the desired item, then press the ENTER or PLAY() button.
2
When using a DVD menu
Some DVDs have unique menu structures called DVD menus. For example, the discs programmed with complex contents
provide guide menus, and those recorded with various languages provide menus for audio and subtitle language. Although
the DVD menus contents and operation differ from disc to disc, the following explains basic operation when this feature is
used.
Then the DVD menu available on the disc is displayed
on TV screen.
If the disc does not have the DVD menu, this function
does not work.
The unit starts playback of the selected item.
When the menu continues onto another screen, repeat
this step until the desired item is selected.
RC
TITLE MENU
Dogs
Cats
Cows
Horses
Example)
Main unit
RC
RCRC
or or
Main unit
RC
RCRC
or or
RC
2. SUBTITLE
1.AUDIO
3. ANGLE
Example)
During playback of the desired chapter/track or title/group, press the REPEAT( ) button.
Then the selected repeat mode is displayed on the TV
screen.
Each time this button is pressed, the repeat mode changes depending on the disc types as follows :
To return to normal playback, press the REPEAT( ) button repeatedly until the REPEAT OFF is displayed.
23
REPEAT PLAYBACK
You can play a current title, group, chapter, folder, track, file, disc or part repeatedly.
Note :
Repeat playback may not work correctly with some discs.
Repeating a chapter/track, title/group
Playback starts from the selected file according to the selected playback mode.
RC
RC
CHAPTER REPEAT ON
TITLE REPEAT ON
REPEAT OFF
: Chapter/track repeat
: Title/group repeat
: Repeat mode off
(normal playback)
REPEAT ONE
REPEAT ALL
REPEAT OFF
: Track repeat
: Entire disc repeat
: Repeat mode off
(normal playback)
REPEAT ONE
FOLDER REPEAT
DISC
DISC REPEAT
SINGLE
FOLDER
: File repeat
: Folder repeat
: Normal playback of the disc
: Entire disc repeat
: Normal playback of a file
: Normal playback of a folder
In the stop mode, press the REPEAT( ) button.
1
To select the desired file, perform the steps 1 and 2 in To start playback from the menu of MP3, WMA, JPEG or
DivX disc on page 16.
2
Each time this button is pressed, one of the various
playback modes is selected and displayed on the TV
screen as follows:
Repeating a file, folder
PLAYING TRACKS/FILES IN RANDOM ORDER
24
During playback, press the RANDOM PLAY button.
Each time this button is pressed, the playback mode changes depending on the disc types as follows:
To return to normal playback, press the RANDOM PLAY button during random playback or in the stop mode, then
RANDOM OFF is displayed.
Note :
Random playback may not work correctly with some discs.
Then the selected playback mode is displayed for
several seconds on the TV screen.
RC
RANDOM ON
RANDOM OFF
: Random playback
Track on the disc are played back
in random order.
: Normal playback.
Continued
Repeating the desired part
1
During playback at the beginning of the part you want to repeat, press the REPEAT A/B button.
2
At the end of the part, press the REPEAT A/B button again.
Then A TO B REPEAT ON or A TO B SET B is displayed on the TV screen, and the part between points A and B is
played back repeatedly.
To return to normal playback, press the REPEAT A/B button repeatedly until A TO B CANCELLED is displayed.
Notes :
You may not use the repeat A/B playback of the part that includes multiple camera angles.
Repeat A/B playback works only within a title or a track.
Then A TO B SET A is displayed on the TV screen.
RC
25
PLAYING TRACKS IN DESIRED ORDER
In the stop mode, press the PROGRAM button.
1
Repeat the above step 2 until the desired tracks are programmed.
3
Then the program mode is displayed on the TV screen.
When the PROGRAM button is pressed again, the
program mode is canceled.
󳂮Clearing the programmed tracks
[ To clear one by one ]
During programming, press the CLEAR button.
[ To clear all programmed tracks ]
During programming or when the STOP(󳂮) button is
pressed to stop program playback, press the PROGRAM
button.
To start program playback, press the PLAY() button or the ENTER button.
4
Select the desired track with pressing the NUMERIC buttons on the remote control.
Example) When the track 5 and 12 are programmed.
For 5 :
For 12 :
2
Playback will start in the programmed order.
After all programmed tracks have been played, it enters
the stop mode without clearing the programmed
tracks.(Program playback is suspended.)
Up to 25 tracks can be programmed to be played in any desired order.
RC
PROGRAM P 00:00
RC
Each time this button is pressed, the programmed tracks
are cleared one by one in the opposite order.
Once program playback is performed, you cannot clear
one by one.
Then the programmed tracks are all cleared.
Opening the disc tray clears all programmed tracks.
RC
Main unit
RC
RC
oror
PROGRAM P 01:05
PROGRAM P 02:12
Programmed track number
Programmed order
26
BOOKMARK PLAYBACK
During playback, press the MARKER button.
1
Press the CURSOR / buttons to select the desired bookmark number.
3
• Then the bookmark menu is displayed on the TV screen.
• When the MARKER button is pressed again, the
bookmark menu disappears.
• Each time the CURSOR or button is pressed, the
mark mode or the recall mode is selected.
• Then the bookmark is stored in the memory.
• Repeat the above steps 1~4 until the desired scenes/
points are marked.
• When the ENTER button is pressed at a previously used
bookmark number, the new scene/point will be marked
with that bookmark.
• Playback resumes from the scene/point corresponding to
the selected bookmark.
Notes:
• Opening the disc tray or turning the power off clears all
stored bookmarks.
• The bookmark function may not work with some discs.
At the desired scene/point, press the ENTER button.
4
Press the CURSOR / buttons to select the mark mode.
2
• The bookmark function allows you to mark the desired scene/point that you can go to quickly.
Up to 14 bookmarks can be stored in the memory.
Storing a bookmark in the memory
To select the recall mode, perform the above steps 1 and 2.
1
Press the CURSOR / buttons to select the bookmark number that you want to recall and press the ENTER
button.
2
Recalling a bookmarked scene/point
RC
RC
RC
RCRC
RC
MARK GOTO TOTAL
01 01 00/14
The bookmark number to be stored
Mark mode
Recall mode
The stored bookmark number
Total number of the stored bookmark
27
It is possible to change the audio language to a different language from the one selected at the initial settings.
(For details, refer to SETTING THE LANGUAGE SETUP on page 31.)
This operation works only with DVDs on which multiple audio languages are recorded.
During playback, press the AUDIO button.
Then the audio language menu is displayed on the TV
screen for several seconds.
Each time this button is pressed, the audio language changes as follows:
Example)
Notes:
You cannot select the preferred audio language when the disc contains only one.
When the disc is changed, etc., the language heard is the one selected at the initial settings. If this is not recorded on the
disc, only the available language on the disc will be heard.
On some discs, an audio language except the selected one at the initial settings may be heard.
In case of some DivX files on which multiple audio languages are recorded, you can also change the audio language with
pressing the AUDIO button.(However, this operation may work differently.)
It is possible to change the subtitle language to a different language from the selected one at the initial settings.
(For details, refer to SETTING THE LANGUAGE SETUP on page 31.)
This operation works only with DVDs on which multiple subtitle languages are recorded.
During playback, press the SUBTITLE button
Then the subtitle language menu is displayed on the TV
screen for several seconds.
Each time this button is pressed, the subtitle language changes as follows:
Example)
Notes :
You cannot select the preferred subtitle language when the disc does not contain the available language.
When the disc is changed, etc., the displayed language is the selected one at the initial settings. If this is not recorded on the
disc, the available language on the disc may be displayed.
On some discs, a subtitle language except the selected one at the initial settings may be displayed.
When a disc supporting the closed caption is played, the subtitle and the closed caption may overlap each other on the TV
screen. In this case, turn off the display of subtitle language.
In case of some DivX files on which multiple subtitle languages are recorded, you can also change the subtitle language with
pressing the SUBTITLE button.(However, this operation may work differently.)
CHANGING THE AUDIO LANGUAGE
Selected audio
language number
Total number Sound recording system
Selected audio language
AUDIO 1/3 : D 5.1 ENGLISH
AUDIO 2/3 : D 2CH ENGLISH
AUDIO 3/3 : D 2CH FRENCH
SUBTITLE 01/02 : ENGLISH SUBTITLE 02/02 : FRENCH SUBTITLE OFF
Selected subtitle
language number
Total number
Selected subtitle language Subtitle display off mode
CHANGING THE SUBTITLE LANGUAGE
RC
RC
28
Some DVDs contain scenes which have been shot simultaneously from multiple camera angles.
For these discs, the same scene can be viewed from each of these different angles.
The recorded angles differ depending on the disc used.
During playback at the scene recorded from multiple camera angles, press the ANGLE button.
During playback at the scene recorded from multiple camera
angles, the angle symbol( ) is displayed on the TV
screen only when the ANGLE MARK is set to ON.(Refer to
When selecting the ANGLE MARK on page 43.)
Each time this button is pressed, the angle changes as follows:
Example)
Note : This function works only at scenes recorded from multiple angles.
󳂮To select a zoom scale
In the zoom on mode,
Each time the button is pressed,
zoom scale changes as follows
025 PCT 󳃅 050 PCT 󳃅 100 PCT 󳃅 150 PCT 󳃅 200 PCT
zoom-out mode zoom-in mode
CHANGING THE CAMERA ANGLE
Selected angle number
Total number
ZOOMING IN/OUT A SCENE
During playback or in the still
picture or the pause mode,
press the ZOOM button.
1
Each time this button is pressed, zoom scale or zoom
mode changes as follows:
The unit zooms in to the center part of the scene.
󳂵 ZOOM X1.5 󳂵 ZOOM X2 󳂵 ZOOM X3 󳂵 ZOOM OFF
Zoom-in mode Zoom playback off mode
ZOOM X2 󳃅 ZOOM OFF
Zoom-in mode Zoom playback off mode
ZOOM ON 󳃅 ZOOM OFF
To return to the previous operation status, press the
ZOOM button repeatedly until the zoom playback is
canceled.
Notes:
The zoom function may not work with some discs or files.
The zoom function may not work properly at some
scenes.
Zooming is not possible at a title or DVD menu, etc.
Only while zooming in a scene,
press the CURSOR ///
buttons to select the desired
part of the scene.
2
In the zoom-in mode only, you can select and view any part of the scene close-up.
RC
RC
RC
RC
29
CHANGING THE VIDEO SIGNAL FORMAT
Depending on the countries, this unit conforms to either the NTSC color system for U.S.A, Canada, etc., or the PAL for
Europe, Australia, China, etc.
If the color system of this unit is different from that of your TV monitor and the discs to be played, the screen may be
somewhat hard to see or the picture quality may be poor.
Only in this case, change the video signal format to another.
(For details about the video signal format of your TV monitor or the discs, refer to the operating instruction of your TV or the
discs jacket.)
You can set the video signal format to the desired at initial settings, too.
(For details, refer to When selecting the TV TYPE on page 33.)
In the stop mode, press the NTSC/PAL button.
Each time this button is pressed, the video signal format
changes as follows:
󳂵 MULTI 󳂵 NTSC 󳂵 PAL
The MULTI is compatible with both NTSC and PAL formats.
CHANGING THE COMPONENT VIDEO OUTPUT SIGNAL
The COMPONENT VIDEO OUTPUTs of this unit can be capable of outputting either conventional interlacing video signal or
progressively scanned video signal(that can reproduce high-density pictures with less flicker).
When the COMPONENT VIDEO OUTPUTs of this unit are connected to the COMPONENT VIDEO INPUTs of TV or
projector, etc., depending on whether the video signal system of your TV or projector, etc. supports the conventional
interlacing(simply called interlaced) video signals or the progressively scanned(simply called progressive) video signals(that
can reproduce high-density pictures with less flicker), you should select the corresponding video signal.
You can set the component video output signal to the desired at initial settings, too.
(For details, refer to When selecting the VIDEO OUTPUT on page 34.)
Notes:
When you select the PROGRESSIVE TV, the S-VIDEO and COMPOSITE VIDEO OUTPUTs of this unit cannot output the
video signals, meaning the picture will not be shown.
When the progressive video signals are input into the non-progressive COMPONENT VIDEO INPUTs of your TV, etc., the
picture may not be shown normally.
Therefore, when the progressive COMPONENT VIDEO INPUTs of TV is not connected to, you should select INTERLACE
TV.
In the stop mode, press the UPSCALE button.
Each time this button is pressed, the component video
output signal changes and INTERLACE TV or
PROGRESSIVE TV is displayed on the TV screen.
RC
RC
󳂮When selecting the LANGUAGE SETUP 󳂮When selecting the VIDEO SETUP
󳂮When selecting the AUDIO SETUP 󳂮When selecting the SPEAKER SETUP
󳂮When selecting the OTHER SETUP
30
Initial Settings
The initial settings of the unit at the factory can be modified as desired later.
Even after the power of the unit is switched to the standby mode, the initial settings are stored in memory until it is changed
the next time.
To exit the setup mode, press the SETUP button, or press
the CURSOR / buttons to select EXIT SETUP on the
main setup menu and press the ENTER button.
Then the selected category will provide you the setting
details using the succeeding screen.
1
In the stop mode(STOP is displayed on the units
display, not RESUME), press the SETUP button
to enter the setup mode.
2
Press the CURSOR / buttons to select a
setting category, then press the ENTER button
to confirm your selection
SETUP MENU - MAIN PAGE
Main setup menu
GO TO LANGUAGE SETUP PAGE
LANGUAGE SETUP
VIDEO SETUP
AUDIO SETUP
SPEAKER SETUP
OTHER SETUP
EXIT SETUP
LANGUAGE SETUP
AUDIO
SUBTITLE
DISC MENUS
OSD LANGUAGE
MAIN PAGE
ENGLISH
GERMAN
FRENCH
SPANISH
OTHERS
31
VIDEO SETUP
TV DISPLAY
TV TYPE
VIDEO OUTPUT
PICTURE MODE
SCART VIDEO
BLACK LEVEL
MAIN PAGE
4:3 PAN-SCAN
4:3 LETTERBOX
16:9 WIDE
33
OTHER SETUP
CAPTIONS
ANGLE MARK
SCREEN SAVER
BACKGROUND
DVD-AUDIO AREA
SACD AREA
PARENTAL
PASSWORD
ON
OFF
43
AUDIO SETUP
DIGITAL OUTPUT
DOWNMIX
DOLBY PRO LOGIC
AUDIO DRC
MAIN PAGE
ON
OFF
36
SPEAKER SETUP
SPEAKER CONFIGURATION
SPEAKER DISTANCE
CHANNEL LEVEL
MAIN PAGE
38
RC
RCRC
Note:
During setting operation, only the STANDBY button and the
buttons required for setting will function.
31
SETTING THE LANGUAGE SETUP
Note :
If the selected language is not recorded in the DVD, one of the recorded languages is automatically selected.
Then the language menu of the selected item is displayed.
Each time the CURSOR or button is pressed, the
language menu or the item menu is selected.
The selected language is colored.
You can select one of languages listed in the language
menu.
When you want to select a language other than
languages listed in the language menu, select
OTHERS.
To turn off the display of subtitle language, select OFF
on the subtitle language menu.
1
Press the CURSOR / buttons to select the preferred item.
Example) When selecting the SUBTITLE
Item menu
AUDIO : When selecting a preferred audio language to be heard from those
included on the DVD.
SUBTITLE : When selecting a preferred subtitle language to be displayed from
those included on the DVD.
DISC MENUS : When selecting a preferred menu language to be displayed from
those included on the DVD.
OSD LANGUAGE : When selecting a preferred OSD(On-Screen Display) language
to be displayed.
LANGUAGE SETUP
AUDIO
SUBTITLE
DISC MENUS
OSD LANGUAGE
MAIN PAGE
ENGLISH
GERMAN
FRENCH
SPANISH
OTHERS
Language menu
RC
LANGUAGE SETUP
AUDIO
SUBTITLE
DISC MENUS
OSD LANGUAGE
MAIN PAGE
OFF
ENGLISH
GERMAN
FRENCH
SPANISH
OTHERS
RCRC
2
Press the CURSOR button to select language menu.
3
Press the CURSOR / buttons to select the preferred language, then press the ENTER button.
RC
32
Continued
󳂮When selecting OTHERS
Then 4-digit language code input screen is displayed.
Refer to the DVD Language Code List on page 53 to find the 4-digit language code for the preferred language and input it
with pressing the NUMERIC buttons, then press the ENTER button.
Example) When inputting 1428
When the 4-digit code is input correctly, the previous menu screen is displayed.
If you input a wrong code, INVALID LANGUAGE CODE is displayed. In this case, input the code again.
󳂮To return to the main setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / buttons to select MAIN PAGE and press
the ENTER button.
Then the main setup menu screen will be displayed.
When the RETURN button is pressed, the main setup menu screen will be displayed, too.
INPUT LANGUAGE CODE
NEW LANG. CODE:
RC
5
Set other setups to your preference.
4
Press the CURSOR button to select the item menu.
Each time the CURSOR or button is pressed, the
item menu or the language menu is selected.
RC
33
SETTING THE VIDEO SETUP
1
Press the CURSOR / buttons to select the preferred item.
Item menu
TV DISPLAY : When selecting a picture size according to the aspect ratio of
your TVs screen
TV TYPE : When selecting the desired video signal format to match that of
your TV monitor and DVD to be played.
VIDEO OUTPUT : When selecting either the conventional interlacing video
signals or the progressively scanned video signals to be
output from the units COMPONENT VIDEO OUTPUTs.
PICTURE MODE : When selecting the picture source mode according to the
type of content being played back.
SCART VIDEO : When selecting the desired video signal(s) to be output from
the units A/V SCART OUTPUT connector.
(Regional option for Europe, etc. only)
BACK LEVEL : When adjusting the intensity of black.
VIDEO SETUP
TV DISPLAY
TV TYPE
VIDEO OUTPUT
PICTURE MODE
SCART VIDEO
BLACK LEVEL
MAIN PAGE
4:3 PAN-SCAN
4:3 LETTERBOX
16:9 WIDE
Setting menu
Then the setting menu of the selected item is displayed.
󳂮When selecting the TV DISPLAY
When you connect a normal TV with 4:3 aspect ratio to the unit, select either 4:3 LETTERBOX or 4:3 PAN-SCAN and when you
connect a wide TV with 16:9 aspect ratio, select 16:9 WIDE.
󳂮When selecting the TV TYPE
Depending on the countries, this unit conforms to either the NTSC color system for U.S.A, Canada, etc., or the PAL for
Europe, Australia, China, etc.
If the color system of this unit is different from that of your TV monitor and the discs to be played, the screen may be
somewhat hard to see or the picture quality may be poor.
Only in this case, change the video signal format to another.
(For details about the video signal format of your TV monitor or the discs, refer to the operating instruction of your TV or discs
jacket.)
You can select the desired video signal format with pressing the NTSC/PAL button, too.
(For details, refer to CHANGING THE VIDEO SIGNAL FORMAT on page 29.)
4:3 PAN-SCAN : DVDs recorded with the 16:9 aspect ratio and the pan-scan
specification are reproduced in the pan-scan screen which
automatically trims the left and right of picture.
4:3 LETTERBOX : DVDs recorded with the 16:9 aspect ratio are reproduced in
the letter box screen which has black bands on the top and bottom.
16:9 WIDE : DVDs recorded with the 16:9 screen are reproduced by filling
the TV screen.
Note: Depending on some DVDs, the playback picture may not conform to
the TV aspect setting you select.
TV DISPLAY
TV TYPE
VIDEO OUTPUT
4:3 PAN-SCAN
4:3 LETTERBOX
16:9 WIDE
VIDEO SETUP
MULTI : When selecting the MULTI that is compatible with both NTSC and PAL
formats.
NTSC : When selecting the NTSC format.
PAL : When selecting the PAL format.
TV DISPLAY
TV TYPE
VIDEO OUTPUT
PICTURE MODE
MULTI
NTSC
PAL
VIDEO SETUP
RC
34
Continued
󳂮When selecting the VIDEO OUTPUT
The COMPONENT VIDEO OUTPUTs of this unit can be capable of outputting either conventional interlacing video signal or
progressively scanned video signal(that can reproduce high-density pictures with less flicker).
When the COMPONENT VIDEO OUTPUTs of this unit are connected to the COMPONENT VIDEO INPUTs of TV or projector, etc.,
depending on whether the video signal system of your TV or projector, etc. supports the conventional interlacing(simply called
interlaced) video signals or the progressively scanned(simply called progressive) video signals(that can reproduce high-density
pictures with less flicker), you should select the corresponding video signal.
You can select the desired video output signal with pressing the UPSCALE button, too.(For details, refer to CHANGING THE
COMPONENT VIDEO OUTPUT SIGNAL on page 29.)
Notes:
When you select the PROGRESSIVE, the S-VIDEO and COMPOSITE VIDEO OUTPUTs of this unit cannot output the video
signals, meaning the picture will not be shown.
When the progressive video signals are input into the non-progressive COMPONENT VIDEO INPUTs of your TV, etc., the picture
may not be shown normally.
Therefore, when the progressive COMPONENT VIDEO INPUTs of TV is not connected to, you should select INTERLACED.
When selecting the PICTURE MODE
There are two types of source content in pictures recorded in DVD : film content(pictures recorded from films at 24 frames per
second) and video content(video signals recorded at 30 frames per second).
According to the type of content being played back, select the desired picture mode.
Notes :
Only when the VIDEO OUTPUT is set to PROGRESSIVE, this setting is valid.
When there is no improvement in picture quality with the selected picture mode, select the AUTO mode.
󳂮When selecting the SCART VIDEO(Regional Option)
For some countries like Europe, this unit incorporates the A/V SCART OUTPUT connector which can deliver the composite
(regular), the S-VIDEO(Y and C) or RGB video signals as well as the audio L and R signals for easy connection.
When the SCART connections between the unit and video equipments are made, you should select the appropriate of the
COMPOSITE, S-VIDEO and RGB video signals.
Notes:
When the VIDEO OUTPUT is set to PROGRESSIVE, the SCART VIDEO cannot be set to RGB, and vice versa.
Be sure to set your TV to the corresponding video signal to match the SCART VIDEO setting of the unit.(Refer to the operating
instructions of the component(s) connected.)
Depending on the SCART VIDEO and VIDEO OUTPUT settings, the video signals will be output as follows:
󳂮Relationship between the SCART VIDEO and video output signal settings
SCART
VIDEO OUTs
A/V SCART OUTPUT
VIDEO
COMPOSITE VIDEO S-VIDEO COMPONENT
setting
VIDEO OUTPUT setting VIDEO OUTPUT setting VIDEO OUTPUT setting VIDEO OUTPUT setting
INTERLACED”“PROGRESSIVE”“INTERLACED”“PROGRESSIVE”“INTERLACED”“PROGRESSIVE”“INTERLACED”“PROGRESSIVE
COMPOSITE
○× ×
(Interlaced)
(Progressive)
composite ×
S-VIDEO
○× ×
(Interlaced)
(Progressive)
S-Video ×
RGB
○× × × ×RGB ×
X: No video signal or abnormal video signal
COMPOSITE : When outputting the composite(regular) video signals from
the A/V SCART OUTPUT connector.
S-VIDEO : When outputting the S-VIDEO signals.
RGB : When outputting the RGB signals.
SCART VIDEO
BLACK LEVEL
COMPOSITE
S-VIDEO
RGB
INTERLACED : When outputting conventional interlacing video signal.
PROGRESSIVE : When outputting progressively scanned video signal.
INTERLACED
PROGRESSIVE
TV DISPLAY
TV TYPE
VIDEO OUTPUT
PICTURE MODE
VIDEO SETUP
AUTO : Select this mode normally. This unit automatically detects source content,
film or video, of playback source, and perform the necessary signal process.
FILM : When the source content in pictures recorded in DVD is film content.
VIDEO : When it is regular video content.
SMART : When it is content having little movement regardless of the types of content.
SUPER SMART : When it is video content having a lot of movement.
PICTURE MODE
SCART VIDEO
BLACK LEVEL
MAIN PAGE
AUTO
FILM
VIDEO
SMART
SUPER SMART
35
NORMAL : Select this to adjust the black level of the video signal to
the standard level.
DARKER : Select this to adjust the black level darker.
BLACK LEVEL
NORMAL
DARKER
󳂮When selecting the BLACK LEVEL
You can select the desired black level to adjust the intensity of black.
Note :
Only when the video signal format is NTSC color system, the black level setting is effective for the video signals(other than the
RGB signals(Regional Option for Europe, etc., and the progressive component video signals).
Continued
󳂮To return to the main setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / buttons to select MAIN PAGE and press
the ENTER button.
Then the main setup menu screen will be displayed.
When the RETURN button is pressed, the main setup menu screen will be displayed, too.
5
Set other setups to your preference.
4
Press the CURSOR button to select the item menu.
Each time the CURSOR or button is pressed, the
setting menu or the item menu is selected.
The selected setting is colored.
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
2
Press the CURSOR button to select the setting menu.
3
Press the CURSOR / buttons to select the preferred, then press the ENTER button.
RCRC
RC
RC
36
SETTING THE AUDIO SETUP
󳂮When selecting the DIGITAL OUTPUT
Notes :
When playing a SACD(including SACD area in case of hybrid SACDs) or a DVD Audio, no digital signals will be output.
When your amplifier/receiver is not compatible with the digital signals that are output from this unit, loud noise or no sound
may be heard from the speakers, and it may be harmful to your ears and damages the speakers. To prevent it, you should set
the DIGITAL OUTPUT to OFF and make analog audio connections.
For details on the digital audio signals that can be output, refer to Audio output from the units DIGITAL OUTPUTs on page 7.
󳂮When selecting the DOWNMIX
Depending on how to connect the analog AUDIO OUTPUT jacks to your amplifier/receiver or TV, you should set the
DOWNMIX correctly.
Depending on whether the 2CH AUDIO OUTPUT jacks (or the A/V SCART OUTPUT connector)to a stereo
amplifier/receiver/TV or an A/V amplifier/receiver with built-in surround decoder, you should set the DOWNMIX to Lo/Ro or
Lt/Rt.
When playing back a DVD Video, DVD Audio or SACD recorded in multichannel signal format, the DOWNMIX setting affects
the signals output from the 2CH OUTPUT Jacks (and the A/V SCART OUTPUT connector) and the same signals are output
from only the FL and FR jacks of 5.1CH AUDIO OUTPUTs.
When connecting only the 5.1CH AUDIO OUTPUTs to your amplifier/receiver, you should set the DOWNMIX to OFF to output
the multichannel audio signals from these jacks as it was recorded.
In this case, only the front left and right signals of the multichannel audio signals will output from the 2CH AUDIO OUTPUT
jacks (and the A/V SCART OUTPUT connector).
Note :
When connecting the 5.1CH AUDIO OUTPUTs to the multichannel audio inputs of an amplifier/receiver that does not have the
speaker setup for the multichannel audio inputs, you should set the SPEAKER SETUP.(For details, refer to SETTING THE
SPEAKER SETUP on page 38)
1
Press the CURSOR / buttons to select the preferred item.
Then the setting menu of the selected item is displayed.
RC
Item menu
DIGITAL OUTPUT : When outputting digital audio signal or not.
DOWNMIX : When outputting a preferred analog audio signal format.
DOLBY PRO LOGIC : When turning on or off the Dolby Pro Logic decoder.
AUDIO DRC(Dynamic Range Compression) : When adjusting the dynamic
range compression that makes faint sound easier to hear at low volume
levels.
AUDIO SETUP
DIGITAL OUTPUT
DOWNMIX
DOLBY PRO LOGIC
AUDIO DRC
MAIN PAGE
ON
OFF
Setting menu
ON : When outputting the digital audio signals as it was recorded.
(However, there are some exceptions depending on audio recording
format recorded in disc.)
OFF : When outputting no digital audio signals.
DIGITAL OUTPUT
DOWNMIX
ON
OFF
AUDIO SETUP
Lt/Rt : When enjoying multichannel surround sound by connecting the units
2CH AUDIO OUTPUTs to an A/V amplifier/receiver with built-in surround
decoder.
Lo/Ro : When enjoying conventional 2 channel stereo sound by connecting
the unit s 2CH AUDIO OUTPUTs to a stereo amplifier/receiver/TV
OFF : When outputting the multichannel audio signals from the 5.1CH AUDIO
OUTPUTs as it was recorded.
DIGITAL OUTPUT
DOWNMIX
DOLBY PRO LOGIC
AUDIO DRC
Lt/Rt
Lo/Ro
OFF
AUDIO SETUP
37
󳂮To return to the main setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / buttons to select MAIN PAGE and press
the ENTER button.
Then the main setup menu screen will be displayed.
When the RETURN button is pressed, the main setup menu screen will be displayed, too.
5
Set other setups to your preference.
4
Press the CURSOR button to select the item menu.
Continued
󳂮When selecting the DOLBY PRO LOGIC
This units built-in Dolby Pro Logic decoder converts 2 channel signals(such as 2 channel Dolby Digital signals of DVD Video
and 2 channel PCM signals of CD, MP3, WMA, DivX) into multichannel(front left, front right, center and surround channel)
signals to which is applied the Dolby Pro Logic surround effect and outputs them from the 5.1CH AUDIO OUTPUT jacks.
Notes :
When the CENTER SP and SURROUND SP is set to NONE, you cannot enjoy the Dolby Pro Logic surround effect even if the
DOLBY PRO LOGIC is set to ON. (For details, refer to When selecting the SPEAKER CONFIGURATION on page 38.)
Only when the DIGITAL OUT is set to OFF, 2 channel PCM(48kHz/16~24 bit) signals of DVD Video can be converted into
multichannel signals.
When the DOWNMIX is set to Lt/Rt or Lo/Ro, you cannot select the DOLBY PRO LOGIC.
󳂮When selecting the AUDIO DRC
This function can be activated, while playing the Dolby Digital program sources only.
ON : When turning on the Dolby Pro Logic decoder.
OFF : When turning it off.
DOLBY PRO LOGIC
AUDIO DRC
ON
OFF
1~8 : When adjusting the dynamic range compression as desired.
0 : When turning off the dynamic range compression.
Note: In some Dolby Digital softwares, this function cannot be available.
DIGITAL OUTPUT
DOWNMIX
DOLBY PRO LOGIC
AUDIO DRC
MAIN PAGE
8
7
6
5
4
3
2
1
0
RC
RCRC
2
Press the CURSOR button to select setting menu.
3
Press the CURSOR / buttons to select the preferred setting, then press the ENTER button.
RC
Each time the CURSOR or button is pressed, the
setting menu or the item menu is selected.
The selected setting is colored.
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
38
SETTING THE SPEAKER SETUP
These settings are valid when the 5.1CH AUDIO OUTPUTs are connected to the multichannel audio inputs of your
amplifier/receiver.(For details, refer to Connecting 5.1CH AUDIO OUTPUTs on page 7.)
To obtain the best possible surround sound, set the size of speakers you have connected and their distances from your
listening position. Then use the test tone to adjust the volume of the speakers to the same level.
Note :
When the 5.1CH AUDIO OUTPUTs are connected to the multichannel audio inputs of an amplifier/receiver that has its own
speaker size, distance and level settings, set each setting on this setup to default value. Then set the speaker setup on the
amplifier/receiver.
For your reference, each default value is as follows :
* For SPEAKER CONFIGURATION, SUBWOOFER : YES, FRONT / CENTER / SURROUND SP : LARGE, CROSSOVER : 100 Hz
* For SPEAKER DISTANCE, FRONT L/R / CENTER / SURROUND L/R : 3.0 M/10 FT
* For CHANNEL LEVEL, FRONT L/R / CENTER / SURROUND L/R / SUBWOOFER : 0 dB
1
Press the CURSOR / buttons to select the SPEAKER CONFIGURATION, then press the ENTER button.
󳂮CROSSOVER FREQUENCY
Crossover frequency is the frequency(Hz) below which the bass sound of each speaker is to output from the subwoofer or
from speakers which are set to LARGE(when not using a subwoofer).
Refer to the operating instructions of the speakers to be connected. If the frequency range of your speaker is 100 Hz~20 kHz,
crossover frequency have to be set to 100 Hz (or slightly higher).
SPEAKER CONFIGURATION
SUBWOOFER
FRONT SP
CENTER SP
SURROUND SP
CROSSOVER
SPEAKER SETUP
YES
NO
Item menu
RCRC
Setting menu
2
Press the CURSOR / buttons to select the preferred item.
Then the setting menu of the selected item is displayed.
RC
SPEAKER CONFIGURATION : When setting the size of the speakers that are
connected and the crossover frequency.
SPEAKER DISTANCE : When setting the distance between the listening position
and each speaker.
CHANNEL LEVEL : When adjusting the volume of the speakers with use of
test tone.
SPEAKER SETUP
SPEAKER CONFIGURATION
SPEAKER DISTANCE
CHANNEL LEVEL
MAIN PAGE
When selecting the SPEAKER CONFIGURATION
39
󳂮To return to the speaker setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / buttons to select SPEAKER SETUP and
press the ENTER button.
Then the speaker setup menu screen will be displayed.
When the RETURN button is pressed, the speaker setup menu screen will be displayed, too.
6
Set other speakers to preferred size, etc.
7
Set other setups to your preference.
3
Press the CURSOR button to select the setting menu.
4
Press the CURSOR / buttons to select the preferred setting, then press the ENTER button.
Each time the CURSOR or button is pressed, the
setting menu or the item menu is selected.
The selected setting is colored.
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
󳂮About speaker size
Depending on your speaker type, you can select one of these following speaker types.
* YES/NO : Select the desired depending on whether a subwoofer is connected or not.
* LARGE : Select this when connecting speakers that can fully reproduce sounds below crossover frequency.
* SMALL : Select this when connecting speakers that cannot fully reproduce sounds below crossover frequency. When this is selected, sounds
below crossover frequency are sent to the subwoofer.
* NONE : Select this when no speakers are connected. When this is selected, sounds are sent to the speakers which are not set to NONE.
Select LARGE or SMALL not according to the actual size of the speaker but according to the speakers capacity for playing
low frequency(bass sound below frequency set for the CROSSOVER FREQUENCE) signals.
When SUBWOOFER is set to NO, FRONT SP cannot be set to SMALL.
When FRONT SP is set to SMALL, CENTER SP and SURROUND SP cannot be set to LARGE.
󳂮About crossover frequency
When speakers are set to SMALL, you should set the CROSSOVER FREQUENCY correctly according to their low frequency
playback capacity.
You can select the preferred within 70~160 Hz.
Continued
5
Press the CURSOR button to select the item menu.
RCRC
RC
RC
1
Press the CURSOR / buttons to select the SPEAKER DISTANCE, then press the ENTER button.
SPEAKER DISTANCE
UNIT
FRONT L
CENTER
FRONT R
SURROUND R
SURROUND L
SPEAKER SETUP
METERS
FEET
Item
menu
Setting menu
RCRC
When selecting the SPEAKER DISTANCE
40
Continued
2
Press the CURSOR / buttons to select the preferred item.
Then the setting menu of the selected item is displayed.
Each time the CURSOR or button is pressed, the
setting menu or the item menu is selected.
󳂮When selecting the preferred unit,
You can select either METERS or FEET.
Once a unit is selected, the distances are automatically
changed in the selected unit.
󳂮When setting the distance
You can set the distance within the range of 1.5~9.0 meters
in 0.3 meter intervals(or 5~30 feet in 1 feet intervals)
Note : You cannot select the subwoofer and speakers set
to NONE.
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
RC
󳂮To return to the speaker setup menu screen
Press the CURSOR
button to select the item menu, press the CURSOR / buttons to select SPEAKER
SETUP and press the ENTER button.
Then the speaker setup menu screen will be displayed.
When the RETURN button is pressed, the speaker setup menu screen will be displayed, too.
6
Set other speakers to preferred distances.
7
Set other setups to your preference.
RCRC
3
Press the CURSOR button to select the setting menu.
4
Press the CURSOR / buttons to select the
preferred setting, then press the ENTER button.
RC
5
Press the CURSOR button to select the item menu.
RC
41
Continued
3
Press the CURSOR / buttons to select ON, then press the ENTER button.
4
Press the CURSOR button to select the item menu.
5
Press the CURSOR / buttons to select the preferred channel to be adjusted, then press the CURSOR button
to select its setting menu.
Each time the CURSOR or button is pressed, the
setting menu or the item menu is selected.
Then the test tone function will work.
When OFF is selected, the test tone function will be
deactivated.
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
Each time the CURSOR or button is pressed, the
setting menu or the item menu is selected.
Note :
You cannot select the speakers set to NO or NONE.
1
Press the CURSOR / buttons to select the CHANNEL LEVEL, then press the ENTER button.
2
Press the CURSOR / buttons to select the TEST TONE, then press the CURSOR button to select
the its setting menu.
RCRC
RCRC
Item menu
Setting menu
CHANNEL LEVEL
TEST TONE
FRONT L
CENTER
FRONT R
SURROUND R
SURROUND L
SUBWOOFER
ON
OFF
RCRC
When selecting the CHANNEL LEVEL
RCRC
RC
42
Continued
Even when the TEST TONE is set to OFF, you can select the preferred channel and adjust its level, too.
󳂮To return to the speaker setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / buttons to select SPEAKER SETUP and
press the ENTER button.
Then the speaker setup menu screen will be displayed.
When the RETURN button is pressed, the speaker setup menu screen will be displayed, too.
7
Press the CURSOR button to select the item menu.
8
Set other speakers to preferred levels.
10
Set other setups to your preference.
You can adjust the volume within the range of -10~0 dB.
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
9
After the speakers are all adjusted as preferred, cancel the test tone function.
6
Press the CURSOR / buttons to adjust the volume of the selected speaker as preferred until the sound level of
each speaker is heard to be equally loud.
RC
RC
󳂮When selecting the CAPTIONS
󳂮
When selecting the ANGLE MARK
󳂮When selecting the SCREEN SAVER
A TV screen may be burned out if a static picture is displayed for a long time in the stop mode.
To prevent this, set the SCREEN SAVER to ON. Then the unit automatically activates the screen saver function if a static
picture is displayed for over 5 minutes.
Note: The monitor screen of a projector or projection TV is easily burned out if a static picture is displayed for a long time.
Be careful not to allow the monitor screen to be burned out when the SCREEN SAVER is set to OFF.
󳂮When selecting the BACKGROUND
43
SETTING THE OTHER SETUP
1
Press the CURSOR / buttons to select the preferred item.
Then the setting menu of the selected item is displayed.
RC
Item menu
CAPTIONS : When turning on or off the display of the closed captions
recorded on DVD.
ANGLE MARK : When displaying the angle symbol on the TV screen during
playback at the scene recorded from multiple camera angles.
SCREEN SAVER : When turning on or off the screen saver function.
BACKGROUND : When selecting a preferred background image to be displayed
on the screen in the stop mode and CD play mode.
DVD AUDIO AREA : When selecting a preferred content to be played on some
DVD Audio discs that contain DVD Video content in addition to DVD Audio.
SACD AREA : When selecting a preferred area to be played on some SACDs that
contain multichannel, 2 channel area, and CD layer(in case of hybrid SACDs).
PARENTAL CONTROL : When restricting playback of DVD Video which contains
violent and other scenes according to the level set by the user.
For example, if a movie which includes violent scenes supports the parental lock
feature, such scenes which you do not want to let children view can be cut or
replaced with other scenes.
PASSWORD : When changing the password for parental lock. The units password
has been set to "3308" at the factory.
OSD : When turning on or off the OSD(On-Screen Display) which shows operation
status or disc information, etc.
DIVX VOD : When using the registration code to purchase or rent the videos from
VOD service.
DEFAULTS : When resetting all the settings made in the setup menu except the rating
level, the password and the registration code to the default settings.
OSD
DIVX VOD
DEFAULTS
ON
OFF
OTHER SETUP
CAPTIONS
ANGLE MARK
SCREEN SAVER
BACKGROUND
DVD-AUDIO AREA
SACD AREA
PARENTAL
PASSWORD
ON
OFF
Setting menu
ON : When turning on the display of the closed captions recorded on DVDs.
OFF : When turning it off.
Notes:
The caption decoder is required to display captions.
DVDs with caption signals are indicated by the mark.
The captions cannot be displayed when playing DVDs which do not contain
caption signals.
CAPTIONS
ANGLE MARK
ON
OFF
OTHER SETUP
ON : When turning on the display of the angle symbol( ) on the TV screen.
OFF : When turning it off.
ANGLE MARK
SCREEN SAVER
ON
OFF
ON : When turning on the screen saver function.
OFF : When turning it off.
SCREEN SAVER
BACKGROUND
ON
OFF
When selecting the items other than PARENTAL CONTROL, PASSWORD, DIVX VOD and DEFAULTS
BLUE : When displaying a blue background on the screen.
BLACK : When displaying a black background.
LOGO : When displaying a DVD logo image.
BACKGROUND
DVD-AUDIO AREA
SACD AREA
BLUE
BLACK
LOGO
44
󳂮When selecting the DVD AUDIO AREA
Some DVD Audio discs consist of DVD Video and DVD Audio contents. You can select the desired area to be played.
(For details, see the discs sleeve notes.)
Note : When the disc dose not contain the selected one at this menu, the available one will be played regardless of the DVD
AUDIO AREA setting.
󳂮When selecting the SACD AREA
Some SACDs consist of 2 channel and multichannel audio areas, and hybrid SACDs comprise 2 layer structure of an
HD(SACD) layer and CD layer. You can select the desired area/layer to be played.(For details, see the discs sleeve notes.)
You can select the desired area/layer with pressing the SACD AREA button, too. (For details, refer to To select a playback
area/layer on page 16.)
Note : When the disc does not contain the selected one at this menu, that cannot be played. Therefore you should select the
desired of the available ones.
󳂮When selecting the OSD
When a SACD contains the information on track, album and artist, etc., the corresponding information will be displayed or not
depending on the OSD setting.
Continued
󳂮To return to the main setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / buttons to select MAIN PAGE and press
the ENTER button.
Then the main setup menu screen will be displayed.
When the RETURN button is pressed, the main setup menu screen will be displayed, too.
5
Set other setups to your preference.
2
Press the CURSOR button to select the setting menu.
3
Press the CURSOR / buttons to select the preferred setting, then press the ENTER button.
Each time the CURSOR or button is pressed, the
setting menu or the item menu is selected.
The selected setting is colored.
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
4
Press the CURSOR button to select the item menu.
RC
RCRC
RC
MULTICHANNEL : When playing the multichannel area (of HD layer).
2CHANNEL : When playing the 2 channel area (of HD layer).
CD : When playing the CD layer.
SACD AREA
PARENTAL
PASSWORD
MULTICHANNEL
2CHANNEL
CD
DVD AUDIO : When playing the DVD Audio content.
DVD VIDEO : When playing the DVD Video content.
DVD-AUDIO AREA
SACD AREA
DVD AUDIO
DVD VIDEO
ON : When turning on the OSD(On-Screen Display) which shows
operation status or disc information, etc.
OFF : When turning it off.
OSD
DIVX VOD
ON
OFF
45
Continued
1
Press the CURSOR / buttons to select the PARENTAL CONTROL.
Notes :
When you set the rating level low, some discs may not be played at all. In this case, set the rating level higher or to NO
PARENTAL.
DVD Videos may or may not respond to the rating level setting. Make sure this function works with your DVD Videos.
When selecting the PARENTAL CONTROL
Each time the CURSOR or button is pressed, the
level menu or the item menu is selected.
2
Press the CURSOR button to select the level menu.
CAPTIONS
ANGLE MARK
SCREEN SAVER
BACKGROUND
DVD-AUDIO AREA
SACD AREA
PARNENTAL
PASSWORD
1 G
2
3 PG
4 PG 13
5
6 PG-R
7 NC-17
8 ADULT
Level 1G :
Select this to play only DVD Videos for children.
Adult and general audience DVD Videos cannot
be played.
Level 2~7 NC-17 :
Select this to play DVD Videos for general audiences
and children. Adult DVD Videos cannot be played.
Level 8 ADULT :
Select this to play for general audiences,
children and adults.
NO PARENTAL :
Select this to play all DVD Videos.
RC
OTHER SETUP
RC
3
Press the CURSOR / buttons to select the preferred level, then press the ENTER button.
PASSWORD VERIFY PAGE
INPUT PASSWORD:
RCRC
When the password is input correctly, the rating level is set to the preferred level and the previous menu screen is displayed.
If you input a wrong password, PASSWORD INCORRECT is displayed. In this case, input the password again.
While displaying the password verify page screen, when the RETURN button is pressed, the other setup menu screen will be
displayed.
Note : If you forgot your password, input 3308 that has been set to at factory.
4
Input a 4-digit password with pressing the NUMERIC(0~9) buttons, then press the ENTER button.
RC
RC
5
Press the CURSOR button to select the item menu.
Each time the CURSOR or button is pressed, the
item menu or the level menu is selected.
RC
When each password is input correctly, the previous menu screen is displayed.
While displaying the password change page menu screen, when the RETURN button is pressed, the other setup menu
screen will be displayed.
Note :
Do not forget the password. When you input the password first time or if you forgot your password, input 3308 that has
been set to at factory for the old password.
1
Press the CURSOR / buttons to select the PASSWORD.
2
Press the CURSOR buttons to select the CHANGE, then press the ENTER button.
3
Input 4-digit passwords in sequence for old password, new password and confirmation, then press the ENTER
button.
PASSWORD
CHANGE
RC
PASSWORD CHANGE PAGE
OLD PASSWORD:
NEW PASSWORD:
CONFIRM :
RC
RC
RC
PASSWORD CHANGE PAGE
XXXX
XXXX
XXXX
RC
OLD PASSWORD:
NEW PASSWORD:
CONFIRM :
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
4
Press the CURSOR button to select the item menu.
RC
When selecting the PASSWORD
46
Continued
6
Set other setups to your preference.
󳂮To return to the main setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / buttons to select MAIN PAGE and press
the ENTER button.
Then the main setup menu screen will be displayed.
When the RETURN button is pressed, the main setup menu screen will be displayed, too.
47
Continued
󳂮To return to the main setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / button to select MAIN PAGE and press the
ENTER button.
Then the main setup menu screen will be displayed.
When the RETURN button is pressed, the main setup menu screen will be displayed, too.
This unit provides you the DivX
®
VOD(Video On Demand) registration code that allows you to rent and purchase videos from
DivX
®
VOD service at www.divx.com/vod.(For details, visit it at www.divx.com/vod.)
5
Set other setups to your preference.
󳂮To return to the main setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / button to select MAIN PAGE and press the
ENTER button.
Then the main setup menu screen will be displayed.
When the RETURN button is pressed, the main setup menu screen will be displayed, too.
5
Set other setups to your preference.
1
Press the CURSOR / buttons to select the DIVX VOD.
DIVX VOD
DEFAULTS
CONFIRM
RC
When selecting the DIVX VOD
Each time the CURSOR or button is pressed, the
setting menu or the item menu is selected.
The registration code will be displayed.
Use the registration code to purchase or rent the videos
from DivX
®
VOD service.
Note: Only the downloaded videos by using this units
registration code can be played back on this unit.
The other setup menu screen will be displayed.
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
2
Press the CURSOR button to select the setting menu, then press the ENTER button.
3
After confirming the registration code, press the ENTER button.
4
Press the CURSOR button to select the item menu.
RCRC
RC
RC
48
Continued
When selecting the DEFAULTS
󳂮To return to the main setup menu screen
Press the CURSOR button to select the item menu, press the CURSOR / button to select MAIN PAGE and press
the ENTER button.
Then the main setup menu screen will be displayed.
When the RETURN button is pressed, the main setup menu screen will be displayed, too.
1
Press the CURSOR / buttons to select the DEFAULTS.
4
Set other setups to your preference.
Each time the CURSOR or button is pressed, the
setting menu or the item menu is selected.
The selected setting is colored.
Each time the CURSOR or button is pressed, the
item menu or the setting menu is selected.
2
Press the CURSOR button to select the setting menu, then press the ENTER button.
3
Press the CURSOR button to select the item menu.
RESET :
When resetting all the settings in the setup
menu except the rating level, the password
and the registration code to the default
settings.
DIVX VOD
DEFAULTS
RESET
RC
RCRC
RC
49
DVD Video structure
DVD Video discs typically contain one or more titles, which
may be subdivided into chapters.
DVD Audio structure
DVD Audio discs contain groups and tracks.
SACD/Audio CD structure
SACDs and Audio CDs contain tracks.
Some SACDs consist of the 2 channel playback area and
the multichannel playback area.
MP3/WMA/JPEG/DivX structure
On an MP3/WMA/JPEG/DivX disc, a folder can be a
member of another folder, creating hierarchical folder layers.
If you are familiar with a personal computer, you may easily
understand the hierarchical file/folder construction.
Aspect ratio (DVD)
The aspect ratio is the ratio between the vertical and
horizontal size of the picture displayed on a TV screen. The
aspect ratio of normal TV screen is 4:3 while that of the
wide-screen TV and HDTV screen is 16:9.
Subtitle (DVD)
Some DVDs contain the recording of more than one subtitle
languages. With these discs, this unit can select one of the
subtitle languages as desired during playback.
Angle (DVD)
Some DVDs contain scenes which have shot simultaneously
from multiple camera angles. With these discs, the same
scene can be viewed from each of these different angles.
DVD Video
The format for storing MPEG-2 video on DVD, with
interactive menus, multiple soundtracks, subtitles, camera
angles, and so on.
DVD Audio
The DVD format for storing up to six(5.1) channels of 24
bit/96 kHz digital audio or two channels of 24 bit /192 kHz
digital audio.
SACD(Super Audio CD)
SACD uses DSD(Direct Stream Digital) technology for
higher quality sound than standard audio CDs. There are
three types of discs : single layer, double layer and hybrid
discs. The hybrid disc contains both standard audio CD and
Super Audio CD information.
Super Audio CD is a registered trade mark.
MPEG(Moving Picture Expert Group)
It is regarded as an international standard for compressing
and restoring digital video and audio signal. MPEG
standards include MPEG-1, MPEG-2 and MPEG-4. Video
CD and MP3 are based on MPEG-1, while DVD Video is
based on MPEG-2.
MP3
MP3 is an audio data compression format, which stands for
MPEG-1 Audio Layer 3. Using MP3, you can achieve a data
reduction of about 1:10.
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
WMA(Windows Media Audio)
WMA is an audio data compression format developed by
Microsoft Corporation. WMA file size is smaller than that of
MP3.
JPEG(Joint Photographic Experts Group)
JPEG is a papular file format for still image compression and
storage.
There are three sub-types of the JPEG format as follows.
baseline JPEG : used for digital cameras, the web, etc.
progressive JPEG : used for the web.
lossless JPEG : an old type, rarely used now.
DviX
DivX is MPEG-4 based video compression technology
developed by DivXNetworks, Inc. It can shrink digital video
to size small enough to be transported over the internet,
while maintaining high visual quality.
DivX, DivX Certified, and associated logos are trademarks
of DivXNetworks, Inc. and are used under license.
Definition Of Terms
Track 1 Track 2 Track 3 Track 4
Multichannel area 2 channel area
Track 1 Track 2 Track 1 Track 2Track 3
Folder Folder
File
File File Folder
File File
File File
File
Dolby Digital
Dolby Digital provides multichannel surround sound in
cinemas from 35 mm film and in the home from laser discs,
DVDs, and digital broadcast television, cable, and satellite
systems. It enables the transmission and storage of up to
five full-range audio channels, plus a low-frequency effects
channel(LFE), thus 5.1 channels, in less space than is
required for just one linear PCM-coded channel on a
compact disc.
Dolby Pro Logic
Audio signal processing technology developed by Dolby
Laboratories for surround sound.
Dolby Pro Logic process outputs four channel(front left/right,
center, surround) signals.
The surround channel is monaural.
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
DTS (Digital Theater Systems)
DTS is a newly-developed surround system which can
handle more amount of data, providing better audio quality.
Though the number of audio channels is 5.1 which is same
as Dolby Digital, discs bearing the “”provides fat
sound and better signal-to-noise ratio, thanks to the lower
audio compression ratio format. It also provides wide
dynamic range and better separation, resulting in
magnificent sound.
DTS and DTS Digital Surround are registered
trademarks of Digital Theater Systems, Inc.
50
Interlaced scan
In the conventional video system, a picture is shown on the
screen in two halves. The interlaced scanning system places
lines of the second half of the picture in-between lines of the
first half of the picture.
Progressive scan
Progressive scanning displays all the horizontal lines of a
picture at one time, as a single frame.
Composite video
A single video signal commonly used in most consumer
video products that contains all luminance, color, and
synchronization information.
S-video
A video signal which improves picture quality over the
standard composite video signal.
Component video
Video signals with three channels of separate information
that makes up the picture. There are some types of
component video, such as Y/CB(Pb)/CR(Pr) and R/G/B.
Bitstream
The digital signal form of multichannel audio data (e.g., 5.1
channel) before it is decoded into its various channels.
Linear PCM
PCM stands for Pulse Code Modulation. Linear PCM is the
usual digital method without compression, used for audio
playback of audio CDs, DVD Videos, etc.
51
Troubleshooting Guide
If a fault occurs, run through the table below before taking your receiver for repair.
If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult your
dealer. Under no circumstances should you repair the unit yourself as this will invalidate the guarantee!
PROBLEM POSSIBLE CAUSE REMEDY
No power
No playback
Malfunction
No picture
Noisy or distorted
picture
Abnormal picture or no
picture
Slight pause of picture
No sound
Noisy or distorted
sound
No playback of DVD
Video contents on a
DVD Audio.
No playback of the
desired area/layer on
a SACD.
Remote control unit
does not operate.
The AC input cord is disconnected.
Poor connection at AC wall outlet or the outlet is
inactive.
The disc is loaded upside down.
The disc is not playable.
The disc is dirty.
The rating level is not set correctly.
The symbol about invalid operation is displayed.
The disc is scratched, dirty badly or unplayable.
The video cords are disconnected.
The incorrect selection of input source on the TV.
The disc is not playable.
The PURE AUDIO indicator lights up on the front panel.
The unit is connected to a VCR directly and the
copyguard function is activated.
The disc is dirty.
It is in rapid advance or reverse playback, or in frame
advance playback.
The component video output signal is not selected
correctly.
The layer transition occurs during playback of DVD
Videos recoded in dual-layer format.
The audio cords are disconnected.
The speakers are disconnected to the amplifier.
The incorrect selection of input source on the amplifier.
Digital signals are not output from the DIGITAL
OUTPUT jacks.
Digital signals cannot be output from a SACD or a
DVD Audio.
The disc is dirty.
Poor connections.
DVD AUDIO AREA is set to DVD AUDIO.
The desired area/layer is not selected.
Batteries are not loaded or exhausted.
The remote sensor is obstructed.
Connect cord securely.
Check the outlet using a lamp or another appliance.
Reload the disc with the printed side up.
Use a playable disc.
Clean the disc.
Set the rating level setting correctly.
(Refer to When selecting the PARENTAL
CONTROL on page 45.)
Adjust the setting correctly.
(Refer to SYMBOL ABOUT INVALID OPERATION
on page 12.)
Press the POWER switch to switch the power off,
press the POWER switch again and then unload the
disc.
Connect the cords correctly.
Select the input source correctly.
Use a playable disc.
Turn off the pure audio function.
Connect the unit so that the picture signal is
transferred directly to the TV.
Clean the disc.
Sometimes a small amount of picture distortion may
appear. This is not malfunction.
Select the component video output signal correctly.
(Refer to CHANGING THE COMPONENT VIDEO
OUTPUT SIGNAL on page 29.)
Sometimes slight pause may occur.
This is not malfunction.
Connect the cords correctly.
Connect the speakers correctly.
Select the input source correctly.
Set the DIGITAL OUTPUT to ON.
(Refer to When selecting the DIGITAL OUTPUT on
page 36.)
Make analog audio connection.
Clean the disc.
Check the connections and connect all cords
securely.
Set the DVD AUDIO AREA to DVD VIDEO.(Refer to
When selecting the DVD AUDIO AREA on page 44.)
Select the desired.(Refer to To select a playback
area/layer on page 16.)
Replace the batteries.
Remove the obstacle.
52
TYPE
System | DVD Video / Audio & SACD player
Laser | Semiconductor laser
AUDIO SECTION
Frequency response
Sampling frequency : 192 kHz, DVD Audio | 4 Hz ~ 88 kHz
Sampling frequency : 96 kHz, DVD | 4 Hz ~ 44 kHz
Sampling frequency : 48 kHz, DVD | 4 Hz ~ 22 kHz
Sampling frequency : 44.1 kHz, Audio CD | 4 Hz ~ 20 kHz
SACD | 2 Hz~100 kHz
Signal to noise ratio, IHF A weighted | 100 dB
Dynamic range
DVD(48 kHz, 24 bit) / SACD / Audio CD | 103 / 108 / 99 dB
Total harmonic distortion, 1 kHz | 0.3 %
Wow and flutter | Unmeasurable (less than ±0.002 %)
Analog output level, 10 k | 2.0 V
Digital output level
Coaxial, 75 | 0.5 Vp-p
Optical, 660 nm | -21 ~ -15 dBm
VIDEO SECTION
Video compression,
DVD / DivX | MPEG 2 / MPEG 4
Horizontal resolution
DVD Video | 500 lines
Output level, 75
VIDEO (regular, COMPOSITE) | 1.0 Vp-p
S-VIDEO : Y/C | 1.0 / 0.286 Vp-p
COMPONENT : Y / Pb / Pr | 1.0 / 0.7 / 0.7 Vp-p
A/V SCART(Regional option) : R / G / B | 0.7 / 0.7 / 0.7 Vp-p
GENERAL
Video signal format | NTSC / PAL
Power supply
U.S.A. and Canada | 120 V~60 Hz
China, Europe, Australia and other countries | 220 - 240 V~50 / 60 Hz
Power consumption | 20 W
Dimension (W x H x D) | 440 x 127 x 356 mm (17-3/8 x 5 x 14 inches)
Weight (Net) | 5.0 kg (11 lbs)
Note : Design and specifications are subject to change without notice for improvements.
Specifications
53
DVD Language Code List
1027
1028
1032
1039
1044
1045
1051
1052
1053
1057
1059
1060
1061
1066
1067
1070
1079
1093
1097
1103
1105
1109
1130
1142
1144
1145
1149
1150
1151
1157
1165
1166
1171
1174
1181
1183
Code Language
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali ; Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faeroese
French
Frisian
Irish
1186
1194
1196
1203
1209
1217
1226
1229
1233
1235
1239
1245
1248
1253
1254
1257
1261
1269
1283
1287
1297
1298
1299
1300
1301
1305
1307
1311
1313
1326
1327
1332
1334
1345
1347
1349
Code Language
1350
1352
1353
1356
1357
1358
1363
1365
1369
1376
1379
1393
1403
1408
1417
1428
1435
1436
1463
1481
1482
1483
1489
1491
1495
1498
1501
1502
1503
1505
1506
1507
1508
1509
1511
1512
Code Language
1513
1514
1515
1516
1517
1521
1525
1527
1528
1529
1531
1532
1534
1535
1538
1539
1540
1543
1557
1564
1572
1581
1587
1613
1632
1665
1684
1697
Code Language
Malayalam
Mongolian
Moldavian
Marathi
Malayalam
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Punjabi
Polish
Pashto ; Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangro
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Tegulu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Chinese
Zulu
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian ; Lettish
Malagasy
Maori
Macedonian
SD-860
DVD-VIDEO / AUDIO & SACD PLAYER
5707-04736-007-0
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sherwood SD-860 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sherwood SD-860 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Sherwood SD-860

Sherwood SD-860 Gebruiksaanwijzing - Deutsch - 54 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info