214303

Sharp xg c45x Handleiding

104
Verklein
Vergroot
Pagina terug
1/106
Pagina verder
LCD PROJECTOR
MODEL
PG-C45X
OPERATION MANUAL
Introduction
Connections and Setup
Basic Operation
Easy to Use Functions
Appendix
IMPORTANT
For your assistance in reporting the loss or theft of your
Projector, please record the Serial Number located on
the bottom of the projector and retain this information.
Before recycling the packaging, please be sure that
you have checked the contents of the carton thoroughly
against the list of “Supplied accessories” on page 14.
Model No.: PG-C45X
Serial No.:
This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/
EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/
68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la
directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla
direttiva 93/68/EEC.
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida
pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la
93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras av 93/68/
EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/EEC.
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should
the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
or and of the same rating as
above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the
mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of
in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian,
Dutch, Portuguese, Chinese (Traditional Chinese and Simplified Chinese), Korean and Arabic. Carefully read
through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch,
Italienisch, Niederländisch, Portugiesisch, Chinesisch (Traditionelles Chinesisch und einfaches Chinesisch),
Koreanisch und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois,
espagnol, italien, néerlandais, portugais, chinois (chinois traditionnel et chinois simplifié), coréen et arabe.
Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska,
italienska, holländska, portugisiska, kinesiska (traditionell kinesiska och förenklad kinesiska), koreanska och
arabiska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, sueco, español,
italiano, holandés, portugués, chino (chino tradicional y chino simplificado), coreano y árabe. Lea
cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, svedese, spagnolo, italiano,
olandese, portoghese, cinese (cinese tradizionale e cinese semplificato), coreano e arabo. Leggere
attentamente le istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans,
Nederlands, Portugees, Chinees (Traditioneel Chinees en Vereenvoudigd Chinees), Koreaans en Arabisch.
Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Sueco, Espanhol, Italiano,
Holandês, Português, Chinês, (Chinês Tradicional e Chinês Simplificado), Coreano e Árabe. Leia
cuidadosamente todas as instruções de operação antes de operar o projetor.
Introduction
-1
Before using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
Introduction
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREWS.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct the interference
at his own expense.
See bottom of actual set.
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
-2
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During
normal operation, when turning the power off always use the power (OFF) button on the projector or on the remote
control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
Caution Concerning the Lamp Replacement
See “Replacing the Lamp” on page 85.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of
these materials may be regulated due to environmental considerations. For disposal or recycling information,
please contact your local authorities or, if you are located in the United States of America, the Electronic Industries
Alliance: www.eiae.org .
PRECAUTIONS A OBSERVER LORS DU
REMPLACEMENT DE LA LAMPE.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.
L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE
AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-XGC50X//1.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.
LAMPE A MOYENNE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIEL
DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE.
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.
HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP.
REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-XGC50X//1 ONLY.
UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS
PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.
LAMP REPLACEMENT CAUTION
Introduction
-3
Outstanding Features
1. Ultra High Brightness from a Compact Projector
• AC 250W Lamp
Use AC 250W lamp for excellent color uniformity and ultra high brightness.
• Power Save mode function enables lower noise levels, reduced power
consumption and longer lamp life.
2. Simple & Easy Operation
• User friendly interface with easy to use operation system and connection
areas makes setup a breeze.
Smooth installation and operation using frequently used buttons,
placement of terminals, color schemes as well as combined use of auto
input and search.
• Simple lens replacement
Using an easy access lens cover and a new bayonnet mount configuration, the optional lens can be
easily installed.
3. Superior PC Compatibility
• Compatible with up to 200 Hz vertical refresh rate, Sync on Green and
Composite Sync signals for use with a wide variety of high-end PCs and
Workstations.
•
Using Advanced Intelligent Compression Technology, computer screens
of UXGA (1,600 # 1,200) resolution can be displayed with minimal distortion.
4. Advanced Computer & Video lntegrated Composer Technology
• Realizes vivid images using the latest image quality circuitry.
• New I/P conversion algorithm enhances the performance of the motion detect I/P
conversion.
Extensive improvements on the jagged edges or slanted
lines in moving images.
• Color Management System
Supports sRGB.
Enables individual settings of lightness, chromatic value
and hue for six target colors.
• Noise Reduction
Allows for a clear image even with noisy source signals.
• New Edge Up-Scaling
Reduces jaggies and flickering when up-scaling edges
of slanted lines, enabling sharper quality images.
5. Anti-theft and Safe Design
• Anti-theft
This function will render the projector useless if a keycode is not entered.
• Notevision Lock Down
The Notevision Lock Down (roof bolt) is coupled together with a metal-
lic optical mechanism. Thus, even if a strong force is applied, the
Notevision Lock Down prevents insert nut from falling out, and since
the projector can be more rigidly installed than in the past, it is effective
both for preventing theft and in terms of safety.
-4
Contents
Adjusting the Picture ........................................ 46
Adjusting Image Preferences .................................. 46
Selecting the Signal Type ....................................... 46
Progressive Mode ....................................................47
Adjusting Computer Images ............................ 48
When Auto Sync is OFF ...........................................48
Saving Adjustment Settings .....................................48
Selecting Adjustment Settings ................................49
Special Mode Settings ............................................49
Checking the Input Signal ....................................... 49
Auto Sync Adjustment ............................................. 50
Auto Sync Display Function ................................... 50
Easy to Use Functions
Selecting the Picture Display Mode ................ 52
Displaying a Still Image .................................... 54
Enlarging a Specific Portion of an Image ....... 55
Gamma Correction Function............................ 56
Displaying Dual Pictures (Pict in Pict) ............ 57
Black Screen Function ..................................... 58
Displaying the Break Timer .............................. 59
Color Management System (C. M. S.) .............. 60
Selecting the Color Reproduction Mode ................. 60
Selecting the Target Color ....................................... 60
Setting the Brightness of the Target Color ...............61
Setting the Chromatic Value of the Target Color...... 61
Setting the Hue of the Target Color ........................ 61
Resetting User-Defined Color Settings ................... 62
Overview of All Color Settings ................................. 62
Setting the Audio Output Type ......................... 63
Setting on/off the Internal Speaker.................. 63
Auto Search Function ....................................... 64
Video Digital Noise Reduction
(DNR) System .............................................. 65
Setting On-screen Display ............................... 65
Setting the Video System ................................. 66
Saving Projected Images .................................. 67
Capturing the Image .............................................. 67
Deleting the Captured Image .................................. 67
Setting a Background Image ............................ 68
Selecting a Startup Image ................................ 68
Selecting the Economy Mode .......................... 69
Setting the Power Save Mode .................................69
Monitor Out/RS-232C Off Function .......................... 69
Automatic Power Off Function ................................. 70
Displaying the Remaining Lamp Life
(Percentage) ................................................. 70
Reversing/Inverting Projected Images ............ 71
Locking the Operation Buttons
on the Projector ........................................... 71
Setting up the Keylock ............................................71
Introduction
Outstanding Features ......................................... 3
Contents............................................................... 4
IMPORTANT SAFEGUARDS ............................... 6
How to Access the PDF Operation Manuals
(Windows, Macintosh) ................................... 9
Part Names ........................................................ 10
Projector (Front and Top View) ................................10
Projector (Rear View) .............................................. 11
Remote Control (Front View) ................................... 12
Remote Control (Top View) ..................................... 12
Using the Remote Control ................................ 13
Available Range of the Remote Control ................. 13
Inserting the Batteries ............................................. 13
Accessories ....................................................... 14
Connections and Setup
Connecting the Projector to Other Devices .... 16
Before Connecting .................................................. 16
This projector can be connected to: .......................16
Connecting the Power Cord ................................... 17
Connecting the Projector to a Computer ............. 18
Connecting to Video Equipment .......................... 20
Connecting to an Amplifier .................................. 22
Controlling the Projector by a Computer ............. 23
Connecting to a Monitor ...................................... 24
Using the Wireless Presentation Function of the
Remote Control ............................................. 25
Using as a Wired Remote Control ....................... 26
Setup .................................................................. 27
Using the Adjustment Feet ..................................... 27
Adjusting the Lens .................................................. 28
Setting up the Screen .............................................. 29
Screen Size and Projection Distance ......................30
Projecting a Reversed/Inverted Image ................... 32
Basic Operation
Setting with the Buttons
Image Projection ............................................... 34
Basic Procedure ......................................................34
Selecting the On-screen Display Language ...........36
Correcting Trapezoidal Distortion
(Keystone Correction) ................................. 38
Setting with the Menus
Menu Bar Items ................................................. 40
Using the Menu Screen .................................... 42
Menu Selections (Adjustments) .............................. 42
Menu Selections (Settings) ..................................... 44
Introduction
-5
Canceling the Keylock Setting ................................72
Selecting the Transmission Speed
(RS-232C) ..................................................... 72
Setting up a Password ...................................... 73
Entering the Password .............................................73
Changing the Password ......................................... 74
If You Forget Your Password ................................... 74
Setting the Anti-Theft........................................ 75
Entering the Keycode ..............................................75
Changing the Keycode ........................................... 76
Initializing the Settings ..................................... 77
Displaying the Adjustment Settings ................ 78
Appendix
Maintenance ...................................................... 80
Replacing the Air Filter ..................................... 81
Maintenance Indicators .................................... 83
Regarding the Lamp ......................................... 85
Lamp ...................................................................... 85
Caution Concerning the Lamp ................................85
Replacing the Lamp ................................................ 85
Removing and Installing the Lamp Unit ................. 86
Resetting the Lamp Timer .......................................87
Connecting Pin Assignments .......................... 88
(RS-232C) Specifications and
Command Settings ...................................... 89
Wired Remote Control Terminal
Specifications .............................................. 92
Computer Compatibility Chart ......................... 93
Troubleshooting ................................................ 94
For SHARP Assistance ..................................... 96
Specifications .................................................... 97
Dimensions ........................................................ 98
Glossary ............................................................. 99
Index ................................................................. 100
-6
1. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
2. Retain Instructions
The safety and operating instructions should be
retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near
a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage
to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product
should follow the manufacturer’s instructions, and
should use a mounting accessory recommended by
the manufacturer.
9. Transportation
A product and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
product and cart combination to
overturn.
10.Ventilation
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product
and to protect it from overheating, and these openings
must not be blocked or covered. The openings should
never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a book-
case or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
IMPORTANT SAFEGUARDS
11. Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you
are not sure of the type of power supply to your home,
consult your product dealer or local power company.
For products intended to operate from battery power,
or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types
of plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the product.
14. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage
to the product due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of
fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to dan-
gerous voltage or other hazards. Refer all servicing to
qualified service personnel.
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to
assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR
FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic
rules for its installation, use and servicing.
Introduction
-7
18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to normal operation.
e. If the product has been dropped or damaged in
any way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
INTELLECTUAL PROPERTY RIGHTS
IMPORTANT
READ BEFORE USING THE PRODUCT
• You have acquired a product that includes software licensed to SHARP Corporation by Lineo, Inc. (“Lineo”).
The Software is protected by copyright laws, international copyright treaties, and other intellectual prop-
erty laws and treaties. Lineo and its suppliers retain all ownership of, and intellectual property rights in
(including copyright), the Software components and all copies thereof, provided however, that certain
components of the Software are components licensed under the GNU General Public License (version
2), which Lineo supports. You may obtain a copy of the GNU General Public License at http://www.fsf.org/
copyleft/gpl.html. Lineo will provide source code for any of the components of the Software licensed
under the GNU General Public License. To obtain such source code, send email to embedix-
support@lineo.com.
• OS: Embedix (Embedded Linux) Embedix (TM) is a registered trademark of
U.S.A. LINEO, Inc.
• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Adobe Acrobat is a trademark of Adobe Systems Incorporated.
• Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• This software is based in part on the work of the Independent JPEG Group.
• All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
19. Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
20. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in proper
operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
-8
IMPORTANT SAFEGUARDS
Be sure to read the following safeguards when setting up
your projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if
lamp ruptures. In case of lamp rupture,
contact your nearest Sharp Authorized
Projector Dealer or Service Center for
a replacement.
See “Replacing the Lamp” on page 85.
Cautions concerning the setup of the projector
■ For minimal servicing and to maintain high image qual-
ity, SHARP recommends that this projector be installed
in an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the lens must be cleaned more often. As long as the
projector is regularly cleaned, use in these environ-
ments will not reduce the overall operation life of the
unit. Internal cleaning should only be performed by a
Sharp Authorized Projector Dealer or Service Center.
Do not set up the projector in places exposed to
direct sunlight or bright light.
■ Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes
out the colors, making viewing difficult. Close the cur-
tains and dim the lights when setting up the screen in a
sunny or bright room.
The projector may safely be tilted to a maximum
angle of 12 degrees.
■ Placement should be within ±12 degrees.
Do not subject the projector to hard impact and/
or vibration.
■ Take care with the lens so as not to hit or damage the
surface of the lens.
Rest your eyes occasionally.
■ Continuously watching the screen for long hours will
make your eyes tired. Be sure to occasionally rest your
eyes.
Avoid locations with high or low temperature.
■ The operating temperature for the projector is from 41°F
to 104°F (+5°C to +40°C).
■ The storage temperature for the projector is from
–4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake vents.
■ Allow at least 7.9 inches (20 cm) of space between the
exhaust vent and the nearest wall or obstruction.
■ Be sure that the intake vent and the exhaust vent are
not obstructed.
■ If the cooling fan becomes obstructed, a protection cir-
cuit will automatically turn off the projector. This does
not indicate a malfunction. Remove the projector power
cord from the wall outlet and wait at least 10 minutes.
Place the projector where the intake and exhaust vents
are not blocked, plug the power cord back in and turn
on the projector. This will return the projector to the
normal operating condition.
Cautions regarding the transportation of the pro-
jector
■ When transporting the projector, be sure not to subject
it to hard impact and/or vibration, as this can result in
damage. Take extra caution with the lens. Before mov-
ing the projector, be sure to unplug the power cord from
the wall outlet, and disconnect any other cables con-
nected to it.
Other connected equipment
■ When connecting a computer or other audio-visual
equipment to the projector, make the connections AF-
TER turning off the projector and the equipment to be
connected.
■ Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of the plug
may vary depending on the region or country you are
using the projector in. When using the projector over-
seas, be sure to use the appropriate power cord for
the country you are in.
Temperature monitor function
■ If the projector starts to overheat
due to setup problems or block-
age of the air vents, “ ” and
“ ” will blink in the lower left
corner of the picture. If the temperature continues to
rise, the lamp will turn off, the temperature warning in-
dicator on the projector will blink, and after a 90-sec-
ond cooling-off period the power will shut off. Refer to
“Maintenance Indicators” on page 83 for details.
Info
• The cooling fan regulates the internal temperature, and
its performance is automatically controlled. The sound
of the fan may change during projector operation due
to changes in the fan speed. This does not indicate
malfunction.
• Do not unplug the power cord during projection or cool-
ing fan operation. This can create damage due to the
rise in internal temperature, as the cooling fan also
stops.
Introduction
-9
PDF operation manuals in several languages are included in the CD-ROM, so that you can
work with the projector, even if you do not have this manual. To utilize these manuals, you
need to install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not
installed Acrobat Reader yet, you can install it from the CD-ROM.
To install Acrobat Reader from the CD-ROM
For Windows:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
4 Double click the “ACROBAT” folder.
5 Double click the language (name of the folder)
that you want to view.
6 Double click the installation program and
follow the instructions on the screen.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “CD-ROM” icon.
3 Double click the “ACROBAT” folder.
4 Double click the language (name of the folder)
that you want to view.
5 Double click the installation program and
follow the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please
download the appropriate version from the Internet.
Accessing the PDF Manuals
For Windows:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
4 Double click the “MANUALS” folder.
5 Double click the language (name of the
folder) that you want to view.
6 Double click the “C45X” pdf file to access the
projector manuals.
Note
• If the desired pdf file cannot be opened by double clicking the mouse, start Acrobat Reader first, then
specify the desired file using the “File”, “Open” menu.
• See the “readme.txt” file on the CD-ROM for important information not included in this operation manual.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “CD-ROM” icon.
3 Double click the “MANUALS” folder.
4 Double click the language (name of the
folder) that you want to view.
5 Double click the “C45X” pdf file to access the
projector manuals.
How to Access the PDF Operation Manuals
(Windows, Macintosh)
-10
Projector (Front and Top View)
Part Names
34
34
83
83
39
42
35
38
50
42
35
43
27
27
Power (ON/OFF)
buttons
Turn the power on or off.
Power indicator
Illuminates red, when the
projector is in standby.
When the power is turned
on, this indicator will
illuminate green.
Lamp replacement
indicator
Illuminates green indicating
normal function. Replace
the lamp when the indicator
illuminates red.
Temperature warning
indicator
When the internal
temperature rises, this
indicator will illuminate red.
UNDO button
For undoing an operation
or returning to the default
settings.
ENTER button
For setting items selected
or adjusted on the menu.
13
Remote control
sensor
81
INPUT button
For switching input mode
1, 2, 3 or 4.
KEYSTONE button
For adjusting Keystone or
Digital Shift setting.
AUTO SYNC button
For automatically
adjusting images when
connected to a computer.
Adjustment buttons
(', ", \, |)
For selecting menu items.
VOLUME buttons
For adjusting the speaker
sound level.
MENU button
For displaying adjustment
and setting screens.
28
Zoom knob
28
Focus ring
80
Intake vent
HEIGHT ADJUST
button
Adjustment foot
Carrying handle
Air filter/cooling
fan (Intake vent)
(on the bottom of
the projector)
Numbers in refer to the main pages in this operation manual where the topic is explained.
Attaching and removing the lens cap
• Press on the two buttons of the lens cap
and attach it on the lens. Then release
the buttons to lock it in place.
• Press on the two buttons of the lens cap
and remove it from the lens.
Introduction
-11
Projector (Rear View)
Using the Kensington Lock
•
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
17
80
AC socket
Exhaust vent
27
18
18
Kensington Security
Standard connector
Adjustment Feet
INPUT 2 terminal
Terminal for
computer RGB and
component signals.
INPUT 1 terminal
Terminal for
computer RGB and
component signals.
24
25
OUTPUT (INPUT 1, 2)
terminal
Shared computer
RGB and component
signals output
terminal
for INPUT 1 and 2.
AUDIO OUTPUT
terminal
Shared audio
output terminal for
INPUT 1, 2, 3 and 4.
23
RS-232C terminal
For controlling
projector using a
computer.
22
USB terminal
Terminal for
connecting a
computer using a
USB cable.
18
AUDIO INPUT 1, 2
terminal
Shared audio input
terminal for INPUT 1
and 2.
20
INPUT 4 terminal
Terminal for
connecting video
equipment with an
S-video terminal.
20
AUDIO (L/R)
INPUT 3, 4
terminals
Shared audio input
terminals for INPUT 3
and 4.
20
INPUT 3 terminal
For connecting
video equipment.
26
WIRED REMOTE
control input
terminal
Carrying the projector
Before carrying the projector, fully
extend the carrying handle.
-12
Remote Control (Front View)
Part Names
38
KEYSTONE button
For adjusting Keystone or Digital
Shift setting.
26
WIRED R/C JACK
For controlling the projector by
connecting the remote control to the
projector.
34
Power (ON/OFF) buttons
For turning the power on or off.
42
MENU button
For displaying adjustment and
setting screens.
42
Adjustment buttons
(', ", \, |)
For selecting menu items.
42
ENTER button
For setting items selected or
adjusted on the menu.
39
UNDO button
For undoing an operation or
returning to the default settings.
55
ENLARGE (Enlarge/Reduce)
buttons
For enlarging or reducing part of
the image.
50
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
35
INPUT buttons
For switching to the respective
input modes.
56
GAMMA button
For correcting the brightness of an
image, when the images displayed
are hard to see because of the
brightness of the room. Four
gamma modes are available to
choose from.
35
VOLUME buttons
For adjusting the speaker sound
level.
13
Remote control signal transmitters
57
PinP button
For displaying dual pictures.
25
FORWARD/BACK buttons
Moves forward or backwards when
connected to a computer using a
USB cable. Same as the [Page
Down] and [Page Up] keys on a
computer keyboard.
54
FREEZE button
For freezing images.
58
BLACK SCREEN button
For superimposing a black screen.
52
RESIZE button
For switching the screen size
(NORMAL, BORDER, etc).
36
MUTE button
For temporarily turning off the
sound.
59
BREAK TIMER button
For displaying the break timer.
Remote Control (Top View)
Introduction
-13
23' (7 m)
30°
30°
45°
Using the Remote Control
■ The remote control can be used to control the projector
within the ranges shown in the illustration.
Note
• The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal
may differ due to the screen material.
When using the remote control:
• Be sure not to drop, expose to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp.
Under that circumstance, move the projector away from the fluo-
rescent lamp.
Inserting the Batteries
The batteries (two R-6 batteries (“AA” size,
UM/SUM-3, HP-7 or similar)) are included in
the package.
1 Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
2 Insert the included batteries.
• Insert the batteries making sure the
polarities correctly match the
and
marks inside the battery
compartment.
3 Insert the lower tab of the
cover into the opening, and
lower the cover until it clicks
in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Insert the batteries making sure the polarities correctly match the and marks inside the battery compart-
ment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak.
Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove
them using a cloth.
• The batteries included with this projector may exhaust over a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
Remote
control
sensor
Remote control
signal transmitters
Remote control
Available Range of the Remote Control
-14
Accessories
Remote control
RRMCGA029WJSA
Two R-6 batteries
(“AA” size, UM/SUM-3, HP-7 or similar)
Power cord
For U.S., Canada, etc.
(11'10" (3.6m))
QACCDA010WJPZ
For Europe, except U.K.
(6' (1.8m))
QACCV4002CEZZ
For U.K., Hong Kong and
Singapore
(6' (1.8m))
QACCBA012WJPZ
For Australia, New
Zealand and Oceania
(6' (1.8m))
QACCL3022CEZZ
Note
• Depending on the region, projectors are shipped only one power cord (see above). Use the power cord
that corresponds to the wall outlet in your country.
3 RCA to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3CP
Computer RGB cable (32'10'' (10.0 m)) AN-C10BM
(for IBM-PC, NEC PC-9821 and PC-98NX series)
AN-C10MC (for Macintosh series)
AN-C10PC
(for NEC PC-98 series (Except NEC PC-9821 and
PC-98NX series))
5 BNC to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3BN
RS-232C serial control cable (32'10" (10.0m)) AN-C10RS
Note
• Some of the cables may not be available depending on the region. Please check with your nearest
Sharp Authorized Projector Dealer or Service Center.
Projector manual and
technical reference CD-ROM
UDSKAA016WJZZ
Sharp Advanced Presentation
Software CD-ROM
UDSKAA017WJZZ
Operation manual (this manual)
Quick reference label
(1)
(2) (3)
(4)
Extra air filter
PFILDA005WJZZ
Lens cap (attached)
PCAPHA003WJSA
Supplied accessories
Optional cables
RGB cable
(9'10" (3m))
QCNWGA012WJPZ
USB cable
(9'10'' (3 m))
QCNWGA014WJPZ
Computer audio cable
(ø3.5 mm stereo minijack cable)
(9'10'' (3 m))
QCNWGA013WJPZ
DIN-D-sub RS-232C
adaptor (6
45
/64'' (15 cm))
QCNWGA015WJPZ
Connections and Setup
Connections and Setup
-16
Connecting the Projector to Other Devices
Before Connecting
Note
• Before connecting, be sure to turn off both the projector and the devices to be connected. After making all
connections, turn on the projector and then the other devices.
When connecting a computer, be sure that it is the last device to be turned on after all the connections are
made.
• Be sure to read the operation manuals of the devices to be connected before making connections.
This projector can be connected to:
A computer using:
■ An RGB cable and a computer audio cable (See page 18.)
■ A DIN-D-sub RS-232C adaptor and an RS-232C serial control
cable (AN-C10RS) (sold separately)
(See page 23.)
Component video or audio-visual equipment:
■ A VCR, Laser disc player or other audio-visual equipment
(See page 20.)
■ A DVD player or DTV* decoder (See page 21.)
*DTV is the umbrella term used to describe the new digital television
system in the United States.
An amplifier or audio components using:
■ An audio cable (commercially available) (See page 22.)
A monitor using:
■ An RGB cable (See page 24.)
■ A computer RGB cable (AN-C10BM, AN-C10MC or AN-
C10PC) (sold separately) (See page 24.)
Connections and Setup
-17
Connecting the Power
Cord
Plug in the supplied power cord into
the AC socket on the rear of the pro-
jector.
Power code
Supplied
accessory
-18
Connecting the Projector to a Computer
Connecting the thumbscrew cables
■ Connect the thumbscrew cable making sure that
it fits correctly into the terminal. Then, firmly se-
cure the connectors by tightening the screws on
both sides of the plug.
■ Do not remove the ferrite core attached to the RGB
cable.
Ferrite core
Connecting to a Computer
Using the RGB Cable
1 Connect the projector to the
computer using the supplied
RGB cable.
• Secure the connectors by tightening
the thumbscrews.
2 To input audio signal, connect
the projector to the computer
using the supplied computer
audio cable.
Note
• See page 93 “Computer Compatibility
Chart” for a list of computer signals com-
patible with the projector. Use with com-
puter signals other than those listed may
cause some of the functions not to work.
• When connecting the projector to a com-
puter in this way, select “RGB” for “Signal
Type” in the “Picture” menu. See page 46.
• A Macintosh adaptor may be required for
use with some Macintosh computers. Con-
tact your nearest Sharp Authorized
Projector Dealer or Service Center.
• Depending on the computer you are us-
ing, an image may not be projected un-
less the signal output setting of the com-
puter is switched to the external output.
Refer to the computer operation manual
for switching the computer signal output
settings.
Supplied
accessories
Connecting the Projector to Other Devices
Computer audio
cable
RGB cable
2
Computer audio cable
To RGB output terminal
To audio output terminal
1
RGB cable
Notebook computer
Connections and Setup
-19
“Plug and Play” function (when connecting to a 15-pin terminal)
■ This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
■ Before using the “Plug and Play” function, be sure to turn on the projector first and the connected
computer last.
Note
• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA
DDC compatible computer.
Connecting to Video Equipment
Connecting the Projector to Other Devices
-20
1
S-video cable (commercially available)
Connecting to Video
Equipment Using an
S-video, a Composite
Video or an Audio Cable
Using an S-video, video, or audio cable, a VCR,
laser disc player or other audio-visual equip-
ment can be connected to INPUT 3, INPUT 4
and AUDIO (L/R) input terminals.
1 Connect the projector to the
video equipment using an S-
video cable or a composite
video cable (both commercially
available).
2 Connect the projector to the
video equipment using a ø3.5
mm stereo minijack to RCA au-
dio cable (commercially avail-
able).
Note
• The INPUT 4 (S-VIDEO) terminal uses a
video signal system in which the picture
is separated into color and luminance sig-
nals to realize a higher-quality image. To
view a higher-quality image, use a com-
mercially available S-video cable to con-
nect the INPUT 4 terminal on the projec-
tor and the S-video output terminal on the
video equipment.
• A ø3.5 mm stereo minijack to RCA audio
cable (commercially available) is required
for audio input.
To S-video output terminal
To video output terminal
To audio output terminal
2
ø3.5 mm stereo minijack to RCA
audio cable (commercially available)
1
Composite video cable
(commercially available)
VCR or other audio-visual equipment
-20
Connections and Setup
-21
Optional
cable
3RCA to 15-pin D-sub cable
Type: AN-C3CP
(9'10" (3.0 m))
To analog component
output terminal
To audio output terminal
2
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
1
3 RCA to 15-pin
D-sub cable (sold separately)
DVD player or
DTV* decoder
Connecting to
Component Video
Equipment
Use a 3 RCA to 15-pin D-sub cable when con-
necting to the INPUT 1 or 2 terminal, compo-
nent video equipment such as DVD players
and DTV* decoders.
*DTV is the umbrella term used to describe
the new digital television system in the United
States.
1 Connect the projector to the
video equipment using the 3
RCA to 15-pin D-sub cable.
2 Connect the projector to the
video equipment using a ø3.5
mm stereo minijack to RCA au-
dio cable (commercially avail-
able).
Note
• When connecting the projector to the
video equipment in this way, select “Com-
ponent” for “Signal Type” in the “Picture”
menu. See page 46.
• A ø3.5 mm stereo minijack to RCA audio
cable (commercially available) is required
for audio input.
Connecting to an Amplifier
Connecting to an
Amplifier or Other Audio
Components
Using a ø3.5 mm stereo minijack to RCA au-
dio cable, an amplifier or other audio compo-
nents can be connected to the AUDIO OUT-
PUT terminal.
Connect the projector to the
amplifier
using a ø3.5 mm
stereo minijack
to
RCA
audio cable (commercially
available).
Info
• Always turn off the projector before
connecting to audio components, in order
to protect both the projector and the
components being connected.
• By using external audio components, the
volume can be amplified for better sound.
• The AUDIO OUTPUT terminal allows you
to output audio to audio components from
the selected AUDIO input terminal (for
INPUT 1 and 2) or AUDIO (L/R) input
terminals (for INPUT 3 and 4) connected
to audiovisual equipment.
• For details on Variable Audio Output (VAO)
and Fixed Audio Output (FAO), see
page 63.
• A ø3.5 mm stereo minijack to RCA audio
cable (commercially available) is required
for audio input.
Amplifier
Audio input terminal
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
Connecting the Projector to Other Devices
-22
Connections and Setup
-23
Connecting to a
Computer Using a DIN-
D-sub RS-232C Adaptor
and an RS-232C Serial
Control Cable
When the RS-232C terminal on the projector
is connected to a computer with a DIN-D-sub
RS-232C adaptor and an RS-232C serial con-
trol cable (cross type, sold separately), the
computer can be used to control the projec-
tor and check the status of the projector. See
page 89 for details.
1 Connect the supplied DIN-D-
sub RS-232C adaptor to an RS-
232C serial control cable (sold
separately).
2 Use the above cables to con-
nect the projector and the com-
puter.
Note
• Do not connect or disconnect an RS-232C
serial control cable to or from the com-
puter while it is on. This may damage your
computer.
• The RS-232C function may not operate if
your computer terminal is not correctly set
up. Refer to the operation manual of the
computer for details.
• See page 88 for connection of an RS-
232C serial control cable.
Optional
cable
RS-232C serial control cable
Type: AN-C10RS (32'10" (10.0 m))
RS-232C terminal
To Audio
Output port
DIN-D-sub
RS-232C adaptor
Supplied
accessory
Desktop computer
RS-232C serial control cable
(sold separately)
DIN-D-sub
RS-232C adaptor
Controlling the Projector by a Computer
-24
Optional
cable
Computer RGB cable (32'10" (10.0 m))
Type: AN-C10BM
AN-C10MC
AN-C10PC
Connecting to a Monitor
Watching Images on
Both the Projector and
a Monitor
You can display computer images on both the
projector and a separate monitor using two
sets of an RGB cable. An RGB cable is sup-
plied with this projector. You need to buy an-
other RGB cable for connecting the projector
to a monitor.
1 Connect the projector to the
computer and monitor using
RGB cables (one is supplied,
the other is sold separately).
2 In the “Options(1)” menu, se-
lect “Economy Mode”, “Mntr.
out/RS232” and then “ON”.
(see page 69.)
Note
• Analog RGB signals as well as Component
signals can be output to the monitor.
Connecting the Projector to Other Devices
To RGB input terminal
Monitor
RGB cable
(sold separately)
RGB cable
(supplied)
Desktop computer
To RGB output terminal
-24
Supplied
accessory
RGB cable
Connections and Setup
-25
FORWARD
button
Using the Wireless Presentation Function of the
Remote Control
The Wireless Presentation function on the projector works the same as the [Page Up] and
[Page Down] keys on a computer keyboard. It can also be used to move forward or backward
when viewing images of presentation software such as PowerPoint
TM
.
Using the Wireless Pre-
sentation Function
1 Connect the projector to the
computer using the supplied
USB cable.
Note
• This function only works with the
Microsoft Windows OS and Mac
OS. However, this function does not
work with the following operation
systems that do not support USB.
• Versions earlier than Windows 95.
• Versions earlier than Windows
NT4.0.
• Versions earlier than Mac OS 8.5.
2 Press or while using
presentation software on your
computer.
• Press to move the page up.
• Press to move the page down.
Supplied
accessory
USB cable
USB
terminal
USB cable
BACK
button
Notebook computer
Connecting the Projector to Other Devices
Using as a Wired Remote Control
Connecting the Remote
Control to the Projector
When the remote control cannot be used due
to the range or positioning of the projector
(rear projection, etc.), connect a ø3.5 mm
minijack cable (commercially available or
available as Sharp service part QCNW-
4870CEZZ) from the WIRED R/C JACK on the
top of the remote control to the WIRED RE-
MOTE control input terminal.
ø3.5 mm minijack cable
(commercially available or available as
Sharp service part QCNW-4870CEZZ)
To WIRED R/C JACK
WIRED REMOTE control input terminal
-26
Connections and Setup
-27
Up
Down
Setup
Using the Adjustment
Feet
The height of the projector can be adjusted
using the adjustment feet at the front and back
of the projector when the surface the projec-
tor is placed on is uneven or when the screen
is slanted.
The projection of the image can be made
higher by adjusting the projector when it is in
a location lower than the screen.
1 Press HEIGHT ADJUST.
2 Lift the projector to adjust its
height and remove your finger
from HEIGHT ADJUST.
3 Rotate the adjustment feet at
the back of the projector for
fine adjustment.
Note
•
When returning the projector to its original
position, hold the projector firmly, press
HEIGHT ADJUST and then gently lower it.
• The projector is adjustable up to approxi-
mately 12 degrees on the front and 3
degrees on the back from the standard po-
sition.
Info
• Do not press HEIGHT ADJUST when the
adjustment foot is extended without firmly
holding the projector.
• Do not hold the lens when lifting or lower-
ing the projector.
• When lowering the projector, be careful
not to get your finger caught in the area
between the adjustment foot and the
projector.
HEIGHT ADJUST
button
Adjustment feet
Adjustment foot
Zoom in
Zoom out
Zoom knob
Focus ring
Adjusting the Lens
The image is focused and adjusted to the
desired size using the focus ring or zoom
knob on the projector.
1 The focus is adjusted by rotat-
ing the focus ring.
2 Zooming is adjusted by mov-
ing the zoom knob.
-28
Setup
Connections and Setup
-29
90°
90°
Example of Standard Setup
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Note
• The projector lens should be centered in the middle of the screen. If the horizontal line passing through the
lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly on
the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when
setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
An optional lens (AN-C12MZ) from Sharp is also available for specialized application. Contact your local Sharp
Authorized Projector Dealer for details on the lens. (Refer to the lens installation manual when attaching a lens.)
Throw Distance
■ The graph below is for 100 inches (254 cm) screen with 4:3 normal mode.
Side View
Top View
• The distance from the screen to the projector
may vary depending on the size of the screen.
P. 3 0
• The default setting can be used, when placing the
projector in front of the screen. If the projected im-
age is reversed or inverted, readjust the setting to
“Front” in “PRJ Mode”. P. 7 1
• Place the projector so that an imaginary horizontal
line that passes through the center of the lens is
perpendicular to the screen.
Audience
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen
according to the desired picture size. (See page 30.)
Screen
5 10 15 20 (ft)
-30
H
Screen
L:Projection distance
Lens center
Base line:
Horizontal line passing through
the lens center
STRETCH Mode (16:9)
Picture (Screen) size Projection distance (L)
Distance from the lens center
Diag. (X) Width Height Maximum (L1) Minimum (L2)
to the bottom of the image (H)
300" (762 cm) 261" (662.9 cm)
147" (373.4 cm)
50' 6" (15.37 m) 39' 3" (11.95 m) –4 15/ 16"(–12.6 cm)
250" (635 cm) 218" (553.7 cm)
123" (312.4 cm)
42' (12.80 m) 32' 8" (9.95 m) –4 1/ 8"(–10.5 cm)
225" (571.5 cm) 196" (497.8 cm)
110" (279.4 cm)
37'10" (11.51 m) 29' 5" (8.95 m) –3 3 / 4" (–9.5 cm)
200" (508 cm)
174" (441.9 cm)
98" (248.9 cm)
33' 7" (10.23 m) 26' 1" (7.95 m) –3 5 / 16"(–8.4 cm)
150" (381 cm)
131" (332.7 cm)
74" (188 cm)
25' 2" (7.66 m) 19' 7" (5.95 m) –2 1 / 2" (–6.3 cm)
133" (337.8 cm) 116" (294.6 cm)
65" (165.1 cm)
22' 3" (6.78 m) 17' 4" (5.27 m) –2 3 / 16"(–5.6 cm)
106" (269.2 cm)
92" (233.6 cm)
52" (132 cm)
17' 9" (5.40 m) 13' 9" (4.19 m) –1 3 / 4" (–4.5 cm)
100" (254 cm) 87" (220.9 cm)
49" (124.4 cm)
16' 9" (5.09 m) 13' (3.95 m) –1 5 / 8" (–4.2 cm)
92" (233.6 cm) 80" (203.2 cm)
45" (114.3 cm)
15' 5" (4.68 m) 11' 11" (3.63 m) –1 9 / 16"(–3.9 cm)
84" (213.3 cm) 73" (185.4 cm)
41" (104.1 cm)
14' (4.27 m) 10' 11" (3.31 m) –1 3 / 8" (–3.5 cm)
72" (182.8 cm) 63" (160 cm) 35" (88.9 cm)
12' (3.65 m) 9' 4" (2.83 m) –1 3 / 16"(–3.0 cm)
60" (152.4 cm) 52" (132 cm) 29" (73.6 cm)
10' (3.03 m) 7' 9" (2.35 m) –31 / 32"(–2.5 cm)
40" (101.6 cm) 35" (88.9 cm) 20" (50.8 cm)
6' 7" (2.00 m) 5' 2" (1.55 m) –11 / 16"(–1.7 cm)
Note
• There is an error of ± 3% in the formula above.
• Values with a minus (–) sign indicate the distance of the lens center below the bottom of the image.
The formula for picture size and
projection distance
L1 (ft) =
(0.0472X – 0.0517) / 0.3048
L2 (ft) =
(0.0367X – 0.0529) / 0.3048
H (in) =
(0.1499X – 0.0064) / 2.54
X: Picture size (diag.) (in)
L: Projection distance (ft)
L1: Maximum projection distance (ft)
L2: Minimum projection distance (ft)
H: Distance from the lens center to
the bottom of the image (in)
The formula for picture size and
projection distance
L1 (ft) =
(0.0514X – 0.0516) / 0.3048
L2 (ft) =
(0.04X – 0.0523) / 0.3048
H (in) =
(– 0.0422X + 0.0018) / 2.54
Standard Lens
Throw ratio
1:1.77 to 2.25
NORMAL Mode (4:3)
Picture (Screen) size Projection distance (L)
Distance from the lens center
Diag. (X) Width Height Maximum (L1) Minimum (L2)
to the bottom of the image (H)
300" (762 cm)
240" (609.6cm)
180"(457.2 cm)
46' 4" (14.12 m) 36' (10.97 m) 17 11 / 16" (45.0 cm)
250" (635 cm) 200" (508 cm) 150" (381 cm)
38' 7" (11.76 m) 30' (9.13 m) 14 3 / 4" (37.5 cm)
200" (508 cm)
160" (406.4 cm)
120" (304.8 cm)
30'10" (9.39 m) 24' (7.29 m) 11 13 / 16" (30.0 cm)
150" (381 cm)
120" (304.8 cm)
90" (228.6 cm)
23' 1" (7.03 m) 17'11" (5.46 m) 8 7 / 8" (22.5 cm)
100" (254 cm) 80" (203.2 cm)
60" (152.4 cm)
15' 4" (4.67 m) 11'11" (3.62 m) 5 7 / 8" (15.0 cm)
84" (213.3 cm) 67" (170.1 cm) 50" (127 cm)
12'11" (3.92 m) 10' (3.03 m) 4 15 / 16" (12.6 cm)
72" (182.8 cm) 58" (147.3 cm)
43" (109.2 cm)
11' (3.35 m) 8' 6" (2.59 m) 4 1 / 4" (10.8 cm)
60" (152.4 cm) 48" (121.9 cm) 36" (91.4 cm)
9' 2" (2.78 m) 7' 1" (2.15 m) 3 9 / 16" (9.0 cm)
40" (101.6 cm) 32" (81.2 cm) 24" (60.9 cm)
6' 1" (1.84 m) 4' 8" (1.42 m) 2 3 / 8" (6.0 cm)
Setup
Screen Size and Projection Distance
Connections and Setup
-31
Note
• There is an error of ± 3% in the formula above.
• Values with a minus (–) sign indicate the distance of the lens center below the bottom of the image.
STRETCH Mode (16:9)
Picture (Screen) size Projection distance (L)
Distance from the lens center
Diag. (X) Width Height Maximum (L1) Minimum (L2)
to the bottom of the image (H)
300
"
(762 cm) 261
"
(662.9 cm)
147" (373.4 cm)
33' 2" (10.10 m) 26' 5" (8.04 m) –5"
(–12.7 cm)
250
"
(635 cm) 218
"
(553.7 cm)
123" (312.4 cm)
27' 7" (8.40 m) 22' (6.69 m) –4 3 / 16"(–10.6 cm)
225" (571.5 cm)
196
"
(497.8 cm)
110" (279.4 cm)
24'10" (7.55 m) 19' 9" (6.01 m) –3 3 / 4" (–9.5 cm)
200
"
(508 cm) 174
"
(441.9 cm) 98
"
(248.9 cm)
22' 1" (6.71 m) 17' 7" (5.34 m) –3 3 / 8" (–8.5 cm)
150
"
(381 cm) 131
"
(332.7 cm) 74
"
(188 cm)
16' 6" (5.01 m) 13' 2" (3.99 m) –2 1 / 2" (–6.4 cm)
133" (337.8 cm)
116
"
(294.6 cm) 65
"
(165.1 cm)
14' 7" (4.44 m) 11' 7" (3.53 m) –2 3 / 16"(–5.6 cm)
106" (269.2 cm)
92" (233.6 cm) 52" (132 cm)
11' 7" (3.52 m) 9' 3" (2.80 m) –1 3 / 4" (–4.5 cm)
100" (254 cm) 87" (220.9 cm)
49" (124.4 cm)
10'11" (3.32 m) 8' 8" (2.63 m) –1 5 / 8" (–4.2 cm)
92" (233.6 cm) 80" (203.2 cm)
45" (114.3 cm)
10' 1" (3.05 m) 8' (2.42 m) –1 9 / 16"(–3.9 cm)
84" (213.3 cm) 73" (185.4 cm)
41" (104.1 cm)
9' 2" (2.78 m) 7' 3" (2.20 m) –1 7 / 16"(–3.6 cm)
72" (182.8 cm) 63" (160 cm) 35" (88.9 cm)
7'10" (2.37 m) 6' 3" (1.88 m) –1 3 / 16"(–3.0 cm)
60" (152.4 cm) 52" (132 cm) 29" (73.6 cm)
6' 6" (1.97 m) 5' 2" (1.55 m) –31 / 32"(–2.5 cm)
40" (101.6 cm) 35" (88.9 cm) 20" (50.8 cm)
4' 3" (1.29 m) 3' 4" (1.01 m) –11 / 16"(–1.7 cm)
The formula for picture size and
projection distance
L1 (ft) =
(0.0311X – 0.0676) / 0.3048
L2 (ft) =
(0.0248X – 0.0693) / 0.3048
H (in) =
(0.1504X – 0.0328) / 2.54
X: Picture size (diag.) (in)
L: Projection distance (ft)
L1: Maximum projection distance (ft)
L2: Minimum projection distance (ft)
H: Distance from the lens center to
the bottom of the image (in)
The formula for picture size and
projection distance
L1 (ft) =
(0.0339X – 0.0669) / 0.3048
L2 (ft) =
(0.027X – 0.0683) / 0.3048
H (in) =
(– 0.0424X + 0.0079) / 2.54
AN-C12MZ
Throw ratio
1:1.18 to 1.48
NORMAL Mode (4:3)
Picture (Screen) size Projection distance (L)
Distance from the lens center
Diag. (X) Width Height Maximum (L1) Minimum (L2)
to the bottom of the image (H)
300" (762 cm) 240" (609.6 cm)
180" (457.2 cm)
30' 5" (9.26 m) 24' 3" (7.38 m) 17 3 / 4" (45.1 cm)
250" (635 cm) 200" (508 cm) 150" (381 cm)
25' 4" (
7.71
m) 20' 2" (
6.14
m) 14 13 / 16" (37.6 cm)
200" (508 cm) 160" (406.4 cm)
120" (304.8 cm)
20' 3" (6.15 m) 16' 1" (4.89 m) 11 13 / 16" (30.0 cm)
150" (381 cm)
120" (304.8 cm)
90" (228.6 cm)
15' 2" (4.60 m) 12' (3.65 m) 8 7 / 8" (22.5 cm)
100" (254 cm) 80" (203.2 cm)
60" (152.4 cm)
10' (3.04 m) 7' 11" (2.41 m) 5 7 / 8" (15.0 cm)
84" (213.3 cm) 67" (170.1 cm) 50" (127 cm)
8' 4" (2.54 m) 6' 8" (2.02 m) 4 15 / 16" (12.6 cm)
72" (182.8 cm) 58" (147.3 cm)
43" (109.2 cm)
7' 2" (2.17 m) 5' 8" (1.72 m) 4 1 / 4" (10.8 cm)
60" (152.4 cm) 48" (121.9 cm) 36" (91.4 cm)
5'11" (1.80 m) 4' 8" (1.42 m) 3 9 / 16" (9.0 cm)
40" (101.6 cm) 32" (81.2 cm) 24" (60.9 cm)
3'11" (1.18 m) 3' 1" (0.92 m) 2 3 / 8" (6.0 cm)
-32
When using the default setting.
▼On-screen Display
Projecting a Reversed/Inverted Image
Projection from behind the screen
■ Place a translucent screen between the projector and the au-
dience.
■ Reverse the image by setting “Rear” in “PRJ Mode”. See
page 71 for use of this function.
Projection using a mirror
■ Place a mirror (normal flat type) in front of the lens.
■ Reverse the image by setting “Rear” in “PRJ Mode”, when the
mirror is placed on the audience side. See page 71 for use of
this function.
Info
• When using a mirror, be sure to carefully position both the pro-
jector and the mirror so the light does not shine into the eyes of
the audience.
Ceiling-mount setup
■ It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation.
Before mounting the projector, contact your nearest Sharp
Authorized Projector Dealer or Service Center to obtain the
recommended ceiling-mount bracket (sold separately.) (AN-
XGCM55 ceiling-mount bracket, its AN-EP101B extension tube
and AN-JT200 universal bracket, adaptor for non-level ceiling
installation (for U.S.A.), BB-M20T ceiling adaptor, its BB-
NVHOLDER280, BB-NVHOLDER550, BB-NVHOLDER900
ceiling mount systems (for GERMANY), or AN-60KT ceiling-
mount bracket, its AN-TK301/AN-TK201 and AN-TK302/AN-
TK202 extension tubes (for countries other than the U.S.A. and
GERMANY))
■ Be sure to adjust the position of the pro-
jector to match the distance (H) from
the lens center position (see page 30)
to the lower edge of the image, when
mounting the projector on the ceiling.
■ Invert the image by setting
“Ceiling + Front” in “PRJ
Mode”. See page 71 for use
of this function.
The image is reversed.
When using the default setting.
▼On-screen Display
The image is reversed.
When using the default setting.
▼On-screen Display
The image is inverted.
Setup
Basic Operation
Basic Operation
Image Projection
▼Keycode input box
-34
Lamp
replacement
indicator
Power
indicator
INPUT
button
',", \, |
buttons
MENU
button
ENTER
button
Power (ON)
button
INPUT
buttons
', ", \, |
buttons
MENU button
ENTER
button
Power (OFF)
button
Basic Procedure
Connect the required external equipment to the pro-
jector before operating the following procedures.
Info
•
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page
36
.
1 Plug the power cord into the
wall outlet.
• The power indicator illuminates red, and
the projector enters standby mode.
2 Press
ON
on the projector or on
the remote control.
• The power indicator illuminates green.
After the lamp replacement indicator il-
luminates, the projector is ready to start
operation.
Note
• The lamp replacement indicator il-
luminates, indicating the status of the
lamp.
Green: The lamp is ready.
Green blinking: The lamp is
warming up.
Red:
The lamp should be replaced.
•
If the power is turned off and immediately
switched on again, the lamp replacement
indicator may take time to illuminate.
• When controlling the projector using
RS-232C commands from a com-
puter, wait for at least 30 seconds
after the power has been turned on,
and then transmit the commands.
When “Anti-Theft” (see page 75) is set,
the keycode input box will appear.
• Enter the keycode.
Note
• When entering the keycode, press
the buttons previously set on the
projector or the remote control.
Info
•
When “Anti-Theft” is set, enter the
keycode or the input display will not ap-
pear. Even when the signal is input, the
display will not appear. (see page 75.)
Power (ON)
button
Power (OFF)
button
Basic Operation
-35
3 Press , , or on
the remote control to select the
INPUT mode.
•
After pressing once on the projector,
use to select the desired input mode.
Note
•When no signal is received, “NO
SIGNAL.”will be displayed. When a
signal that the projector is not pre-
set to receive is received, “NOT
REG.” will be displayed.
• When “Auto Search” is “ON”, the
INPUT modes with signals can be
selected. (see page 64.)
• The INPUT mode is not displayed
when “OSD display” is set to “Level
A” or “Level B”. (see page 65.)
About the INPUT modes
VOLUME
buttons
4 Press or on the remote
control to adjust the volume.
Note
• Pressing will lower the volume.
Pressing will raise the volume.
• On the projector, the volume can be
adjusted by pressing
or .
•
, on the projector operate
as cursor buttons (\, |) when the
menu screen is active.
"On-screen Display (Example)
Using RGB
Using
Component
INPUT 2 mode
Using
Component
INPUT 1 mode
INPUT 3 mode
Using Video
INPUT 4 mode
Using S-Video
Using RGB
➝
➝➝
➝
Used for projecting im-
ages from equipment that
sends RGB signals or
component signals con-
nected to the RGB input
terminal.
Used for
projecting
im-
ages
from equipment
connected to the VIDEO
input terminal.
Used for projecting im-
ages from equipment
connected to the S-
VIDEO input terminal.
INPUT 1
INPUT 2
(RGB/
Component)
INPUT 3
(Video)
INPUT 4
(S-Video)
Image Projection
Power (ON)
button
5 Press to temporarily turn
off the sound.
Note
• Pressing again will turn the
sound back on.
6 Press , then press again
while the confirmation message
is displayed, to turn off the pro-
jector.
Note
• If you accidentally pressed and
do not want to turn off the power,
wait until the confirmation message
disappears.
Info
• Do not unplug the power cord dur-
ing projection or cooling fan opera-
tion. This can cause damage due
to the rise in internal temperature,
as the cooling fan also stops.
• When connected to equipment such
as an amplifier, be sure to turn off
the power to the equipment con-
nected first and then to the projec-
tor.
Selecting the On-screen
Display Language
• The on-screen display language of the
projector can be set to English, German,
Spanish, Dutch, French, Italian, Swedish,
Portuguese, Chinese, Korean or Japa-
nese.
1 Press .
• The menu will be displayed.
2 Press \ or | to select “Lan-
guage”.
MUTE button
-36
Power (OFF)
button
ENTER button
MENU
button
', ", \, |
buttons
Basic Operation
-37
3 Press ' or " to select the de-
sired language, and then press
.
4 Press .
• The desired language will be set as
the on-screen display.
Correcting Trapezoidal Distortion (Keystone Correction)
Correcting Trapezoidal
Distortion
This function allows for Keystone (On-screen
Trapezoidal Distortion) Correction.
Note
• When the image is projected either from
top or from bottom towards the screen at
an angle, the image becomes distorted
trapezoidally.
The function for correcting trapezoidal dis-
tortion is called Keystone Correction.
• The Keystone Correction can be adjusted
up to angle of approximately ±35 degrees.
1 Press .
• Pressing again while the BOR-
DER, STRETCH or SMART STRETCH
screen is displayed will start the Digital
Shift function. See page 39.
2 Press ', ", \ and | to adjust
the Keystone correction.
• If you want to make more detailed cor-
rections, press
to display the test
pattern, and then press
''
''
',
""
""
",
\\
\\
\ and
||
||
| to make the adjustments.
Note
•
Since the trapezoidal distortion of the im-
age can be corrected up to an angle of
approximately ±35 degrees, the actual
screen can be diagonally set up to that
angle as well.
•
Press to cancel Keystone Correction.
•
When no signal is detected, the test pat-
tern will be displayed without pressing
.
3 Press .
Note
• You can use the same settings used
in NORMAL mode 4:3 for 16:9.
• Straight lines or the edges of images
may appear jagged while adjusting
the image.
KEYSTONE button
UNDO button
ENTER button
Normal screen
Keystone Correction screen
Compresses
upper side.
Compresses
lower side.
Test pattern
-38
', ", \, |
buttons
Basic Operation
-39
• The Digital Shift function works with BORDER, STRETCH or SMART STRETCH screen. For details,
see page 53.
Digital Shift Setting
For easier viewing, this function shifts the entire image projected on
the screen up or down when projecting 16:9 images from DVD
players and DTV* decoders.
* DTV is the umbrella term used to describe the new digital television
system in the United States.
UNDO button
Press ' to move the
projected image upwards.
Press to reset the
image.
Press " to move the
projected image
downwards.
Press to reset the
image.
-40
Menu Bar Items
This list shows the items that can be set in the projector.
■ INPUT 1 / 2 Mode
Note
• The resolution, vertical frequency and horizontal frequency figures displayed above are for example
purposes only.
• Only when the signal type is set as “Component”, in the “Picture” menu of INPUT 1 or 2 “Color”, “Tint” and
“Sharp” are displayed.
•
Some items cannot be reset, even when “All Reset” in Options (2) has been selected. For details see page 77.
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+3–3
Main menu Sub menu
Main menu Sub menu
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
Reset
Signal Type
Progressive Mode
RGB
Component
2D Progressive
3D Progressive
Film Mode
Picture
Page 46
+30–30
+30–30
Custom 3Custom 1
+30–30
Color Selected
Target
Lightness
Chroma
Hue
Reset (This Color)
Reset (All Colors)
View Settings
[R] Red
[Y] Yellow
[G] Green
[C] Cyan
[B] Blue
[M] Magenta
C.M.S.
Page 60
Standard
sRGB
+150–150
+150–150
+30–30
+60–60
1
2
•
•
7
1
2
•
•
7
1
2
3
4
•
•
7
Resolution
1024 × 864
1152 × 864
1152 × 870
1152 × 882
Resolution
1024 × 768
800 × 600
Vert Freq
60 Hz
75 Hz
Resolution
1024 × 768
800 × 600
Vert Freq
60 Hz
75 Hz
1024 × 768
48.4 KHz
60 Hz
Fine Sync
Page 48
Clock
Phase
H-Pos
V-Pos
Reset
Save Setting
Select Setting
Special Modes
Signal Info
Auto Sync
Auto Sync Disp [ON/OFF]
Resolution
Hor Freq
Vert Freq
OFF
Normal
High Speed
Options (1)
Page 63
Auto Search [ON/OFF]
DNR
OSD Display
Image Capture
Background
Startup Image
Economy Mode
Power Save [ON/OFF]
Mntr.out/RS232 [ON/OFF]
Auto Power Off [ON/OFF]
OFF
Level 1
Normal
Level A
Level B
Save Image
Delete
Sharp
Custom
Blue
None
Sharp
Custom
None
Options (2)
Page 70
Lamp Life
PRJ Mode
Keylock Level
Password
Anti-Theft
All Reset
Speaker [ON/OFF]
Front
Ceiling + Front
Rear
Ceiling + Rear
Normal
Level A
Level B
Old Password
New Password
Reconfirm
RS-232C
9600 bps
38400 bps
115200 bps
Old Code
New Code
Reconfirm
Level 3
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Language
Page 36
Status
Page 78
Audio Out
FAO
VAO
Basic Operation
-41
■ INPUT 3 / 4 Mode
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Page 78
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+3–3
Main menu Sub menu Main menu Sub menu
Picture
Page 46
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
Reset
Progressive Mode
2D Progressive
3D Progressive
Film Mode
Options (2)
Page 70
Lamp Life
PRJ Mode
Keylock Level
Password
Anti-Theft
All Reset
Front
Ceiling + Front
Rear
Ceiling + Rear
Normal
Level A
Level B
Old Password
New Password
Reconfirm
Old Code
New Code
Reconfirm
RS-232C
9600 bps
38400 bps
115200 bps
Language
Page 36
Status
+30–30
+30–30
Custom 3Custom 1
+30–30
Color Selected
Target
Lightness
Chroma
Hue
Reset (This Color)
Reset (All Colors)
View Settings
[R] Red
[Y] Yellow
[G] Green
[C] Cyan
[B] Blue
[M] Magenta
C.M.S.
Page 60
Standard
Auto Search [ON/OFF]
DNR
OSD Display
Video System
Background
Startup Image
OFF
Level 1
Normal
Level A
Level B
Auto
PAL (50/60Hz)
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
Sharp
Custom
Blue
None
Sharp
Custom
None
Economy Mode
Level 3
Speaker [ON/OFF]
Audio Out
FAO
VAO
Options (1)
Page 63
Power Save [ON/OFF]
Mntr.out/RS232 [ON/OFF]
Auto Power Off [ON/OFF]
This projector has two sets of menu screens that allow you to adjust the image and various
projector settings.
You can operate the menus from the projector or remote control using the following proce-
dure.
Using the Menu Screen
Menu screen for INPUT 1
or INPUT 2 RGB mode
Menu screen for INPUT 3
or INPUT 4 Mode
Menu Bar
(Main Menu)
""
""
"Menu Screen
Menu Selections
(Adjustments)
1 Press .
• The menu screen is displayed.
Note
• The “Picture” menu screen for the
selected input mode is displayed.
• The on-screen display shown on the
lower right is displayed when the IN-
PUT 1 or 2 mode is selected.
Menu Bar
(Main Menu)
-42
MENU button
''
''
',
""
""
",
\\
\\
\,
||
||
|
buttons
ENTER button
MENU button
ENTER
button
''
''
',
""
""
",
\\
\\
\,
||
||
|
buttons
Basic Operation
-43
2 Press
\\
\\
\ or
||
||
| to select the
menu you want to adjust.
Note
• For details on the menus, see the
tree charts on pages 40 and 41.
3 Press
''
''
' or
""
""
" to select the item
you want to adjust.
Note
• To display a single adjustment item,
press
after selecting the item.
Only the menu bar and the selected
adjustment item will be displayed.
Then if you press ' or ", the fol-
lowing item (“Red” is after “Bright”)
will be displayed.
• Press
to return to the previous
screen.
4 Press
\\
\\
\ or
||
||
| to adjust the item
selected.
• The adjustment is stored.
5 Press .
• The menu screen will disappear.
||
||
|
▼ Menu screen
Menu Selections
(Settings)
1 Press .
• The menu screen is displayed.
Note
• The “Picture” menu screen for the
selected input mode is displayed.
• The on-screen display shown on the
lower right is displayed when INPUT
1 or 2 mode is selected.
2 Press
\\
\\
\ or
||
||
| to select the
menu you want to adjust.
Note
• For details on the menus, see the
tree charts on pages 40 and 41.
3 Press
''
''
' or
""
""
" to select the
item you want to set.
Note
• Press to return to the previous
screen.
• In some menus, select the icon us-
ing “
”.
Using the Menu Screen
Sub menu
-44
MENU button
''
''
',
""
""
",
\\
\\
\,
||
||
|
buttons
ENTER button
MENU button
ENTER
button
''
''
',
""
""
",
\\
\\
\,
||
||
|
buttons
Basic Operation
-45
4 Press
||
||
|.
• The cursor shifts to the sub menu.
5 Press
''
''
' or
""
""
" to select the set-
ting of the item displayed in the
sub menu.
6 Press .
• The item selected is set.
Note
• Some adjustment items will display
a confirmation message.
When setting an item, press \ or
| to select “Ye s ” or “OK” and then
press .
7 Press .
• The menu will disappear.
Sub menu
Adjusting the Picture
You can adjust the projector’s picture to your preferences with the following picture settings.
Selected Item Description
\ button | button
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
For adjusting the contrast level
For adjusting the brightness of an image
For adjusting the color intensity of the image
For adjusting the tones of an image
For making sharper or softer the contour of an image
For adjusting the redness level
For adjusting the blue level
For adjusting the color temperature of an image
For less contrast
For less brightness
For less color intensity
Skin tones become purplish
For less sharpness
For weaker red
For weaker blue
Decreases color
temperature for warmer,
reddish, incandescent-
like images.
For more contrast
For more brightness
For more color intensity
Skin tones become greenish
For more sharpness
For stronger red
For stronger blue
Increases color
temperature for cooler,
bluish, fluorescent-like
images.
Adjusting Image Preferences
Adjust the “Picture” menu on the menu screen.
➝
For operating the menu screen, see pages 42 to 45.
Note
• “Color”, “Tint” and “Sharp” are not displayed
when selecting INPUT 1 or 2 and the “Sig-
nal Type” is “RGB” .
• The picture adjustments can be stored
separately in each input mode.
• When the signal type in INPUT 1 or 2 has
been set to Component, “Sharp” can be
adjusted when 480I, 480P, 540P, 580I,
580P, 720P, 1035I or 1080I signals are
connected.
• To reset all adjustment items, select “Re-
set” and press
.
•“Red”, “Blue” and “CLR Temp” cannot be
adjusted when “Color Selected” on the
C.M.S. menu is set to “sRGB”.
Selecting the Signal Type
This function allows you to select the input sig-
nal type RGB or Component for INPUT 1 or 2.
Select “Signal Type” in the “Picture” menu on the menu screen.
➝
For operating the menu screen, see pages 42 to 45.
Note
• RGB
Set when RGB signals are received.
•
Component
Set when Component signals are received.
-46
Basic Operation
-47
Progressive Mode
This function allows you to select the progres-
sive display of a video signal. The progres-
sive display projects a smoother video image.
Select “Progressive Mode” in the “Pic-
ture” menu on the menu screen.
➝For operating the menu screen, see
pages 42 to 45.
Note
• 2D Progressive
This function is useful to display fast-
moving images such as sports and ac-
tion films. This mode optimizes the im-
age in a displayed frame.
•
3D Progressive
This function is useful to display relatively
slow-moving images such as drama and
documentary more clearly.
This mode optimizes the image by esti-
mating the movement of a number of pre-
ceding and succeeding frames.
•
Film Mode
Reproduces the image of film source
clearly. Displays the optimized image of
film transformed with three-two pull down
(NTSC and PAL60Hz) or two-two pull
down (PAL50Hz and SECAM) enhance-
ment to progressive mode images.
* The film source is a digital video record-
ing with the original encoded as is at 24
frames/second. The projector can con-
vert this film source to progressive video
at 60 frames/second with NTSC and
PAL60Hz or at 50 frames/second with
PAL50Hz and SECAM to play back a
high-definition image.
• When using progressive inputs, these
inputs are directly displayed therefore 2D
Progressive, 3D Progressive and Film
Mode cannot be selected. These modes
can be selected in interlace signals other
than 1080
I.
• In NTSC or PAL60Hz, even if the 3D Pro-
gressive mode has been set, the three-
two pull down enhancement will be en-
abled automatically, when the film source
has been entered.
• In PAL50Hz or SECAM, the two-two pull
down enhancement will be enabled only
in the Film Mode, when the film source
has been entered.
Adjusting Computer Images
Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in
portions of the screen.
When Auto Sync is OFF
When “Auto Sync” is “OFF”, interference such
as flickering or vertical stripes may occur if
displaying tilings or vertical stripes. Should
this occur, adjust “Clock”, “Phase”, “H-Pos”
and “V-Pos” for obtaining an optimum image.
Select “Clock”, “Phase”, “H-Pos” or “V-
Pos” in the “Fine Sync” menu on the
menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• Computer image adjustments can be made
easily by pressing
. See page 50 for
details.
Saving Adjustment
Settings
This projector allows you to store up to seven
adjustment settings for use with various com-
puters.
Select “Save Setting” in the “Fine Sync”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Selected Item Description
Clock
Phase
H-Pos
V-Pos
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.
-48
Basic Operation
-49
Selecting Adjustment Settings
Adjustment settings stored in the projector
can be easily accessed.
Select “Select Setting” in the “Fine
Sync” menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• If a memory position has not been set, a
resolution and frequency setting will not
be displayed.
• When selecting a stored adjustment set-
ting with “Select Setting”, you can set the
projector in the stored adjustments.
Special Mode Settings
Ordinarily, the type of input signal is detected
and the correct resolution mode is automati-
cally selected. However, for some signals, the
optimal resolution mode in “Special Modes” on
the “Fine Sync” menu screen may need to be
selected to match the computer display mode.
Set the resolution by selecting “Special
Modes” in the “Fine Sync” menu on the
menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• Avoid displaying computer patterns which
repeat every other line (horizontal stripes).
(Flickering may occur, making the image
hard to see.)
• When a DVD player or Digital Video is con-
nected, select 480P as the input signal.
•
See “Checking the Input Signal” below for infor-
mation on the currently selected input signal.
Checking the Input Signal
This function allows you to check the current
input signal information.
Select “Signal Info” in the “Fine Sync”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• The projector will display the number of
scanned lines available from audio-visual
equipment such as a DVD player or Digi-
tal Video.
Auto Sync Adjustment
Used to automatically adjust a computer image.
Select “Auto Sync” in the “Fine Sync”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
When setting to “ Normal” or
“
High Speed”:
• Auto Sync adjustment will occur when the
projector is turned on or when the inputs
are switched, when connected to a com-
puter.
Manual adjustments should be per-
formed:
• When the optimum image cannot be
achieved with Auto Sync adjustment. See
page 48.
• Auto Sync adjustment may take some
time to complete, depending on the im-
age of the computer connected to the pro-
jector.
• When setting “Auto Sync” to “OFF” or
“High Speed”, and if
is pressed Auto
Sync will be executed in “High Speed”
mode. If the button is pressed again
within one minute, Auto Sync will be ex-
ecuted in “Normal” mode.
Adjusting Computer Images
AUTO SYNC button
Screen display during Auto Sync
-50
Auto Sync Display
Function
Used to set the screen displayed during Auto
Sync.
Select “Auto Sync Disp” in the “Fine
Sync” menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• ..... The image set as a background
image is projected.
• ..... The computer image being ad-
justed is displayed.
Easy to Use Functions
Easy to Use Functions
-52
Selecting the Picture Display Mode
Switching the Picture
Display Using Different
Input Signals
Press .
• Each time is pressed, the display
changes as shown on page 52 and 53.
Info
• In the Dot by Dot Mode, images are dis-
played in the original resolution, therefore
they will not be enlarged.
• To return to the standard image, press
while “RESIZE” is displayed on the screen.
This function allows you to modify or customize the picture display mode to enhance the
input image. Depending on the input signal, you can choose “NORMAL”, “FULL”, “DOT BY
DOT”, “BORDER”, “STRETCH” or “SMART STRETCH” image.
RESIZE
button
Screen display of the picture display mode
4:3 aspect ratio
Other aspect ratios
SVGA (800 × 600)
XGA (1024 × 768)
SXGA (1280 × 960)
UXGA (1600 × 1200)
SXGA (1280 × 1024)
NORMAL
1024 × 768
1024 × 768
1024 × 768
1024 × 768
960 × 768
FULL
—
—
—
—
1024 × 768
DOT BY DOT
800 × 600
—
1280 × 960
1600 × 1200
1280 × 1024
Resolution lower than
XGA
NORMAL
Projects a full screen image
while maintaining the aspect ratio.
FULL
Projects a full screen image
while ignoring the aspect ratio.
DOT BY DOT
Projects the original resolution
signal of the image.
4:3 aspect ratio
Input Signal
Output screen image
XGA
Resolution higher than
XGA
COMPUTER
• “NORMAL” is fixed when XGA (1024 × 768) signals are entered.
4:3 aspect ratio
4:3 aspect ratio
SXGA (1280 × 1024)
Easy to Use Functions
-53
SMART STRETCH
1024 × 576*
—
—
480I, 480P, 580I, 580P,
NTSC, PAL, SECAM
540P
720P, 1035I, 1080I
4:3 aspect ratio.
Letter box, squeeze
16:9 aspect ratio
16:9 aspect ratio
NORMAL
1024 × 768
—
—
BORDER
768 × 576*
—
—
STRETCH
1024 × 576*
480I, 480P,
580I, 580P,
NTSC, PAL, SECAM
4:3 aspect ratio
Input Signal
Output screen image
Letter box
Squeeze
16:9 aspect ratio
VIDEO
• “STRETCH” is fixed when 720P, 1035I or 1080I signals are entered.
* The Digital Shift function can be used with these images.
SMART STRETCH
Projects the image fully in a
16:9 screen by enlarging only
the surrounding areas while
keeping the aspect ratio in
the middle part of the image
at 4:3.
NORMAL
Projects a full screen image.
BORDER
Projects 4:3 image fully in
STRETCH (the following
column) image.
STRETCH
Projects 16:9 image evenly
over entire screen
(top/bottom black bands).
16:9 aspect ratio
(4:3 aspect ratio in
16:9 screen)
16:9 aspect ratio
720P, 1035I, 1080I
FULL
Projects the center part in a 4:3
screen by enlarging 1.3 times
toward the horizontal direction.
FULL
—
1024 × 768
—
540P
54
Freezing a Moving
Image
1 Press .
• The projected image is frozen.
2 Press again to return to the
moving image from the cur-
rently connected device.
Displaying a Still Image
This function allows you to instantly freeze a moving image. This is useful when you want to
display a still image from a computer or video, giving you more time to explain the image to
the audience.
FREEZE
button
"On-screen Display
-54
Easy to Use Functions
-55
Enlarging a Specific Portion of an Image
Displaying an Enlarged
Portion of an Image
1 Press .
• Enlarges the image.
• Pressing
or enlarges or re-
duces the projected image.
Note
• You can change the location of the
enlarged image using ', ", \ and
|.
• When an image with a resolution
higher than SXGA is displayed, “×2”
and “×3” cannot be selected.
2 Press to cancel the opera-
tion, then the magnification
returns to ×1.
Note
In the following cases, the image will
return to the normal size (×1).
• When switching the INPUT mode.
• When has been pressed.
• When the input signal is changed.
• When the input signal resolution
and refresh rate (vertical frequency)
change.
This function allows you to enlarge a specific portion of an image. This is useful when you
want to display a detailed portion of the image.
ENLARGE
(Enlarge/
Reduce)
buttons
×1 ×4 ×9 ×16 ×36 ×64×2 ×3
To enlarge
To reduce
"On-screen Display
',",\,|
buttons
56
Selected Mode
STANDARD
PRESENTATION
CINEMA
CUSTOM
Description
For Standard picture
Brightens darker portions of image for more enhanced presentations.
Gives greater depth to darker portions of image for a more exciting theater experience.
Allows you to adjust gamma value using Sharp Advanced Presentation Software.
Gamma Correction Function
Gamma is an image quality enhancement function that offers a richer image by brightening
the darker portions of the image without altering the brightness of the brighter portions.
When you are displaying images with frequent dark scenes, such as a film or concert, or
when you are displaying images in a bright room, this feature makes the dark scenes easier
to see and gives the impression of greater depth in the image.
GAMMA button
UNDO button
STANDARD CUSTOM
PRESENTATION CINEMA
-56
Adjusting Gamma
Correction
1 Press .
• Each time is pressed, the gamma
level toggles between the different
types of gamma modes.
2 To return to the default settings,
press
when “GAMMA” is
displayed.
Note
• The Gamma mode does not oper-
ate for INPUT 1 or INPUT 2 when
“Color Selected” on the C.M.S.
menu is set to “sRGB”.
Easy to Use Functions
-57
Displaying Dual Pictures (Pict in Pict)
Picture in Picture function allows you to display two pictures on the same screen. You can
display the image input from INPUT 3 or 4 as an inset picture overlapping the main picture
from INPUT 1 or 2.
Displaying the Inset Picture
1 Press .
2 Press or on the remote
control or
on the projector
to switch the image in the in-
set picture .
3 Press
''
''
',
""
""
",
\\
\\
\ and
||
||
| to set the
position of the inset picture.
• Press to stop the frame from mov-
ing or to make the frame disappear.
4 Press to move the inset pic-
ture.
• The inset picture will be moved to the
inset picture frame.
Note
• The inset picture can only be displayed
with composite video (NTSC/PAL/
SECAM) or S-Video signal.
• The Freeze function works only with the
inset picture, when the Pict in Pict mode
is in operation.
When the signal entered into INPUT 1 or 2
is as follows, Pict in Pict does not work:
• With a resolution that exceeds SXGA.
• When the input signal is 480
I, 480P,
540P, 580
I, 580P, 720P, 1035I or 1080I.
• When the input signal has changed to
the Interlace mode using RGB signals.
• When the picture display mode is set to
“DOT BY DOT”.
• When no signals are sent to INPUT 1 or
2, or when the resolution or refresh rate
(vertical frequency) is changed.
', ", \, | buttons
PinP button
INPUT 3/4 buttons
UNDO button
ENTER button
58
Black Screen Function
-58
BLACK SCREEN
button
" Projected Image
This function can be used to display a black screen.
Blacking out the Pro-
jected Image
1 Press .
• The screen turns black and “BLACK
SCREEN” is displayed on the screen.
2 To return to the original
projected image, press
again.
Easy to Use Functions
-59
Displaying the Break Timer
"On-screen Display
Displaying and Setting
the Break Timer
1 Press . The break timer
starts to count down from 5
minutes.
2 When
“ ”
is displayed, press
''
''
' ,
""
""
" ,
\\
\\
\ or
||
||
| to set the break
timer.
• You can set anywhere between 1 and
60 minutes (in 1 minute units).
• The break timer starts to count down
as soon as ' , " , \ or | is pressed.
3 Press to cancel the break
timer.
Note
• Auto Power Off will be temporarily dis-
abled during the break timer.
When no input signal is detected for more
than 15 minutes, the projector will auto-
matically shut off if the break timer has
elapsed.
• The break timer will be displayed on the
startup image. To change the screen dis-
played during the break timer, change the
setting of “Startup Image” (see page 68).
BREAK TIMER
button
This function can be used to show the remaining time for break during meeting.
', ", \, |
buttons
-60
Color Management System (C. M. S.)
Selecting the Color
Reproduction Mode
Select “Color Selected” in the “C.M.S.”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• For additional information about sRGB
function, visit “http://www.srgb.com/”.
• “sRGB” cannot be selected for “Color Se-
lected” on the C.M.S. menu when “Com-
ponent” is selected for “Signal Type” on
the “Picture” menu.
• When “sRGB” is selected;
• The gamma correction cannot be set.
• “Red”, “Blue” or “CLR Temp” in “Picture”
cannot be adjusted.
• If “Standard” or “sRGB” is selected for
“Color Selected”, other items (e.g., Target)
cannot be adjusted.
Info
• When “sRGB” is selected, the projected
image may become dark; however, this
does not indicate a malfunction.
Selecting the Target
Color
Select “Target” in the “C.M.S.” menu on
the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
This function allows you individually adjust the display characteristics of six colors (R: Red,
Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta) .
Red Cyan
Yellow Blue
Green Magenta
-60
Description
Sharp default setting
“Lightness”, “Chroma” and “Hue” can
be adjusted for each of the six colors.
The mode changes to sRGB
Selected item
Standard
Custom 1-3
sRGB
Easy to Use Functions
-61
Setting the Brightness
of the Target Color
Select “Lightness” in the “C.M.S.”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Setting the Chromatic
Value of the Target
Color
Select “Chroma” in the “C.M.S.” menu
on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Setting the Hue of the
Target Color
Select “Hue” in the “C.M.S.” menu on
the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
-62-62
Color Management System (C.M.S.)
Resetting User-Defined
Color Settings
Select “Reset (This Color)” or “Reset
(All Colors)” in the “C.M.S.” menu on
the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Overview of All Color
Settings
Select “View Settings” in the “C.M.S.”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Description
“Lightness”, “Chroma” and “Hue” of the
color selected for “Target” are reset.
“Lightness”, “Chroma” and “Hue” of
all colors are reset.
Selected item
Reset
(This Color)
Reset
(All Colors)
Easy to Use Functions
-63
Setting the Audio Out-
put Type
Select “Audio Out” in the “Options (1)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Setting on/off the Inter-
nal Speaker
Select “Speaker” in the “Options (1)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Setting on/off the Internal Speaker
This function allows you to set on/off the internal speaker.
Setting the Audio Output Type
Selected Item
FAO
(Fixed audio output)
Description
Audio output that does not vary in strength with the volume level of the
source projector.
Audio output that varies in strength with the volume level of the source
projector.
VAO
(Variable audio output)
This function allows you to set the audio output type.
-64
Auto Search Function
This function automatically searches for and switches to the input mode in which signals
are being received, when the projector is turned on, or when the INPUT button is pressed.
-64
Using Auto Search
Select “Auto Search” in the “Options
(1)” menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• ON
Automatically switches to the input mode
in which signals are being received, when
turning on the projector or pressing
on
the projector.
•
OFF
For switching input modes manually in
order by pressing on the projector.
• To stop searching for the input mode,
press
on the projector, or , ,
or on the remote control.
Info
• Even while this function is searching for
input signals, whenever , , or
on the remote control is pressed, the
input mode is switched to the respective
one.
• Even while the function is searching for
input signals, pressing on the projec-
tor returns to the previous input mode.
Easy to Use Functions
-65
Video Digital Noise Reduction (DNR) System
Reducing Image Noise
Select “DNR” in the “Options (1)” menu
on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• Set a level so as to view a clearer picture.
Make sure to set DNR to “OFF” in the fol-
lowing cases:
• When the image is blurry.
• When the contours and colors of moving
images drag.
• When TV broadcasts with weak signals
are projected.
Info
• This function is available with INPUT 1, 2
(480
I, 480P, 580I and 580P signals) and
INPUT 3, 4 (all signals).
Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross
color noise.
This function allows you to turn on or off the on-screen messages. When setting “ Level A”
or “ Level B” in “OSD Display”, the input mode display (e.g. INPUT 1) will not appear, even
if the INPUT button is pressed.
Turning Off the
On-screen Display
Select “OSD Display” in the “Options
(1)” menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Setting On-screen Display
Selected Item
Normal
Level A
Level B
Description
All On-screen Displays are displayed.
Input/Freeze/Enlarge/Auto Sync/Volume/Mute/Black Screen are not displayed.
All On-screen Displays are not displayed.
(except Menu, On-Screen Displays displayed when the KEYSTONE button is pressed,
and warning displays (Power off/Temp./Change The Lamp., etc.))
-66
Setting the Video System
Setting the Video
System
Select “Video System” in the “Options
(1)” menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• The video signal can only be set in IN-
PUT 3 or INPUT 4 mode.
• In “Auto”, images are displayed in PAL
even if PAL-N or PAL-M input signals are
received.
When connected to PAL video equipment.
When connected to SECAM video
equipment.
When reproducing NTSC signals in
PAL video equipment.
When connected to NTSC video equipment.
PA L
SECAM
NTSC4.43
NTSC3.58
The video input system mode is preset to “Auto”; however, a clear picture from the con-
nected audio-visual equipment may not be received, depending on the video signal differ-
ence. In that case, switch the video signal.
-66
Easy to Use Functions
-67
Saving Projected Images
• This projector allows you to capture projected images (RGB signals) and set them as a
startup image, or background image when no signals are being received.
• You can capture the images that are input using RGB signals.
Capturing the Image
Select “Image Capture” in the “Options
(1)” menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
1 Press
''
''
' or
""
""
" to select
“
Save Image” and press .
• The projected image is captured. It
may take some time for capturing.
2
11
11
1 Press
\\
\\
\ or
||
||
| to select
“Yes”.
22
22
2 Press
.
Note
• Only images from XGA (1024 × 768) non-
interlace signals in INPUT 1 or INPUT 2
mode can be captured.
• The saved image is reduced to 256 colors.
• Images from equipment connected to
INPUT 3 or INPUT 4 terminal cannot be
captured.
• Only one image can be captured and
saved.
• The color of images may differ before and
after saving if an image is captured on
which image adjustment has been per-
formed using the “C.M.S.” function.
Deleting the Captured
Image
1
Select “ Delete” and press .
2
11
11
1 Press
\\
\\
\ or
||
||
| to select “OK”.
22
22
2 Press .
68
Setting a Background Image
This function allows you to select the image displayed when no signal is being sent to the projector.
*1 You can set a captured image as a background image by selecting “Custom”.
*2 If the input signal has interference, the screen will be displayed with the interference.
Selecting a
Background Image
Select “Background” in the “Options
(1)” menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• When “Custom” is selected, an image
saved using “Image Capture” can be dis-
played as a background image.
•
A “Custom” image is preset as a black screen.
Selecting a Startup Image
This function allows you to specify the image to be displayed upon the projector’s startup.
* You can set a captured image as a startup image by selecting “Custom”.
Selecting a Startup Image
Select “Startup Image” in the “Options
(1)” menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• When “Custom” is selected, an image
saved using “Image Capture” can be dis-
played as a startup image.
•
A “Custom” image is preset as a black screen.
Selected Item
Sharp
Custom
*1
Blue
None
Description
SHARP default image
User customized image (e.g. company logo)
Blue screen
Black screen
*2
Selected Item
Sharp
Custom *
None
Description
SHARP default image
User customized image (e.g. company logo)
Black screen
-68
Easy to Use Functions
-69
Selecting the Economy Mode
These functions allow you to reduce the power consumption of the projector.
Setting the Power Save
Mode
Select “Power Save” in “Economy
Mode” under the “Options (1)” menu on
the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• Although lamp life and noise are improved
when “Power Save” is set to “ON”, bright-
ness decreases by 20%.
• “Power Save” mode is factory preset to
“OFF”.
Monitor Out/RS-232C
Off Function
This projector consumes power when using a
monitor connected to the OUTPUT (INPUT 1,
2) terminal and a computer connected to the
RS-232C terminal. When not using these ter-
minals, “Mntr.out/RS232” can be set to “OFF”
to reduce standby power consumption.
Select
“Mntr.out/RS232”
in “Economy
Mode” under the “Options (1)” menu
on
the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
ON
Monitor Out/RS-232C connection
is set to “ON”.
OFF
Monitor Out/RS-232C connection
is set to “OFF”.
Note
• Set “Mntr.out/RS232” to “ON” when using
the Sharp Advanced Presentation Software.
Brightness
80%
100%
Status
ON
(Low power
mode)
OFF
(Standard
mode)
Power
consumption
290 W
340 W
Lamp Life
2,000 hours
1,500 hours
-70-70
Remaining Lamp Life
(Percentage)
Displaying the Remaining Lamp Life (Percentage)
Checking the Remaining
Lamp Life (Percentage)
This function allows you to check the remain-
ing lamp life (percentage).
Select the “Options (2)” menu on the
menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• It is recommended that the lamp be
changed when the remaining lamp life
becomes 6%.
For lamp replacement, contact your
nearest Sharp Authorized Projector
Dealer or Service Center.
• The table at the right indicates rough esti-
mates in the case of using only in each mode
shown. Remaining lamp life changes within
the range of the values shown depending
on the frequency at which “Power Save” is
switched “ON” and “OFF” (see page 69).
Automatic Power Off
Function
When no input signal is detected for more than
15 minutes, the projector will automatically
power off if set to “ON”.
The Auto Power Off function will be disabled
when it has been set to “OFF”.
Select “Auto Power Off” in “Economy
Mode” under the “Options (1)”
menu on
the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• When the Auto Power Off function is set
to “ON”, 5 minutes before the power turns
off, the message “Power OFF in X min.”
will appear on the screen to indicate the
remaining minutes.
-70
Selecting the Economy Mode
Remaining lamp life
100% 6%
2,000 hours 133 hours
1,500 hours 100 hours
Used with only “ON”
on “Power Save”
(Low power mode)
Used with only “OFF”
on “Power Save”
(Standard mode)
Easy to Use Functions
-71
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function that allows you to reverse or
invert the projected image for various applications.
Setting the Projection
Mode
Select “PRJ Mode” in the “Options (2)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• If a password has been set, the password
input box will be displayed when select-
ing the “PRJ Mode”.
• This function is used for the reversed im-
age and ceiling-mount setups. See page
32 for these setups.
Locking the Operation Buttons on the Projector
This function can be used to lock the use of certain operation buttons on the projector.
The following are the three keylock levels.
Setting up the Keylock
Select “Keylock Level” in the “Options
(2)” menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• If a password has been set, the password
input box will be displayed when select-
ing the “Keylock Level”.
Selected Item
Front
Ceiling + Front
Rear
Ceiling + Rear
Description
Normal image
Inverted image
Reversed image
Reversed and inverted image
Keylock Level
Normal
Level A
Level B
Description
All operation buttons are functional.
Only INPUT/VOLUME buttons on the projector are available.
All operation buttons on the projector are unavailable.
Front Ceiling+Front Rear Ceiling+Rear
-72
Canceling the Keylock
Setting
When the Keylock Level is set to “Normal”,
all buttons are functional.
Select “Keylock Level” in the “Options
(2)” menu on the menu screen and set
“ Normal”
.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• When a password has been set, and
“Keylock Level” is selected, the password
input box will be displayed.
• If both a password and the Keylock Level
have been set at the same time, the pass-
word will be necessary before changing
the Keylock Level.
Selecting the Transmission Speed (RS-232C)
This menu allows you to adjust the transmission speed of the RS-232C connection by select-
ing the baud rate.
Selecting the Transmis-
sion Speed (RS-232C)
Select “RS-232C” in the “Options (2)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• When a password has been set, and “RS-
232C” is selected, the password input box
will be displayed.
• Make sure that both the projector and
computer are set for the same baud rate.
Refer to the computer’s operation manual
for instructions for setting the computer’s
baud rate.
-72
Locking the Operation Buttons on the Projector
Easy to Use Functions
-73
Setting up a Password
Entering the Password
Select “Password” in the “Options (2)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
1 Press
''
''
' or
""
""
" to select the de-
sired number and then press
||
||
|.
2 Enter the 3 remaining digits
and press
.
3 Enter the password again in
“Reconfirm” and press
.
Note
• When a password is set, you need
to enter the password to change
“PRJ Mode”, “Keylock Level”, “RS-
232C”, “Anti-Theft” and “All Reset”
settings.
A password can be set by the user to prevent adjustments to certain settings on the “Options
(2)” menu. Using a password together with the Keylock Level (page 71) is more effective.
-74
Changing the Password
Select “Password” in the “Options (2)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
1 Press
''
''
',
""
""
" and
||
||
| to enter the
password in “Old Password”
and press
.
2 Press
''
''
',
""
""
" and
||
||
| to set the
new password and press
.
3 Enter the new 4-digit password
again in “Reconfirm” and
press
.
Note
• If you do not want to set a password, leave
the fields in procedures 2 and 3 blank and
press .
• To cancel the password settings, click
.
If You Forget Your
Password
If you forget the password, delete it and set a
new password using the following procedure.
Press
-74
Setting up a Password
ON ON
ON
Easy to Use Functions
-75
Setting the Anti-Theft
The anti-theft function prevents unauthorized use of the projector. You can choose to use
this function or not. If you do not want to use this function, just do not enter the keycode.
Once the anti-theft function is activated, users will need to enter the correct keycode each
time the projector is turned on. Failure to enter the correct keycode will cause images not to
be projected. The following procedures explain how to use this function.
Entering the Keycode
• “Anti-Theft” cannot be selected unless
“Password” is set. (See page 73.)
• When “Anti-Theft” is selected, the password
input box will appear. Enter the keycode af-
ter the right password is entered.
Select “Anti-Theft” in the “Options (2)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Info
• Once the function is activated, you must
remember the correct keycode. We sug-
gest you record the keycode in a safe
place where only authorized users have
access. If you lose or forget your keycode,
you will need to contact your nearest
Sharp Authorized Projector Dealer or Ser-
vice Center (see page 96). You may need
to bring your projector to them to restore
the projector to original factory condition
(password and keycode reset).
1 Press any button you like on
the remote control or projec-
tor to set the first digit in “New
Code”.
Note
• The following buttons on the remote
control and projector cannot be set
as keycodes:
• POWER (ON/OFF) buttons
• ENTER button
• UNDO button
• MENU button
• FORWARD button
• BACK button
-76-76
Setting the Anti-Theft
2 Enter the remaining 3 digits by
pressing any buttons you like.
3 Enter the same keycode once
more in “Reconfirm”.
Note
• The Keylock function will become
temporarily disabled.
When “Anti-Theft” is set, the keycode
inputting box appears after the power
is turned on. When it appears, enter the
right keycode.
• Press the buttons on the remote control if
the buttons on the remote control are used
for setting the keycode. In the same manner,
press the buttons on the projector if the
buttons on the projector are used for setting
the keycode.
Changing the Keycode
• When “Anti-Theft” is selected, the password
input box is displayed. After the password has
been entered, you can change the keycode.
Select “Anti-Theft” in the “Options (2)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
1 Press the buttons on the re-
mote control or the projector
to enter the preset 4-digit
keycode in “Old Code”.
2
Press any button you like on
the remote control or the pro-
jector to enter the new keycode.
3 Enter the same 4-digit keycode
in “Reconfirm”.
Note
• If you do not want to set a keycode, leave
the keycode field blank in steps 2 and 3
and press .
Easy to Use Functions
-77
Initializing the Settings
This function allows you to initialize the settings you have made in the projector.
Returning to the
Default Settings
Select “All Reset” in the “Options (2)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
• If a password has been set, the pass-
word input box will be displayed when
selecting “All Reset”.
The following items cannot be initialized.
• C. M. S.
• “Lightness”, “Chroma” and “Hue”
respectively saved for Custom 1-3 on the
C.M.S. menu.
• Fine Sync
• Special Modes
• Signal Info
• Options
• Lamp Life
• Anti-Theft
• Language
• Image stored using “Image Capture”
-78
This function can be used to display all the adjusted settings as a list on the screen.
Displaying the Adjustment Settings
Overview of All Menu
Settings
Select the “Status” menu on the menu
screen and press .
➝ For operating the menu screen, see
pages 42 to 45.
-78
Appendix
Appendix
-80
Cleaning the lens
■ Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the coat-
ing film on the surface of the lens.
■ As the surface of the lens can easily get dam-
aged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Maintenance
Cleaning the projector
■ Be sure to unplug the power cord before clean-
ing the projector.
■ The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or thinner,
as these can damage the finish on the cabinet.
■ Do not use volatile agents such as insecticides
on the projector.
Do not attach rubber or plastic items on the pro-
jector for long time.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the
projector.
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in a
neutral detergent diluted with water, wring the
cloth well and then wipe the projector.
Strong cleaning detergents may discolor, warp
or damage the coating on the projector.
Make sure to test on a small, inconspicuous area
on the projector before using.
Wax
Thinner
Neutral detergent
diluted with water
Neutral detergent
C
leaning
P
aper
Appendix
-81
Replacing the Air Filter
Air filter
Tab
M4
M4
M4
M4
• This projector is equipped with air fil-
ters to ensure the optimal operating
condition of the projector.
• The air filters should be cleaned ev-
ery 100 hours of use. Clean the filters
more often when the projector is used
in a dusty or smoky location.
• Ask your nearest Sharp Authorized
Projector Dealer or Service Center to
exchange the filter (PFILDA005WJZZ)
when it is no longer possible to clean.
Cleaning and replacing
the bottom air filter
1 Turn off the power and discon-
nect the power cord.
• Press . Wait until the cooling fan
stops.
2 Remove the bottom filter cover.
• Turn over the projector. Grab the tab
and slide open the filter cover in the
direction of the arrow.
3 Remove the air filter.
• Pick the air filter up with your fingers
and lift it out of the filter cover.
Power (OFF) button
Power
(OFF)
button
Air filter
(not removable)
4 Clean the air filter.
• Clean the dust off the air filter and
cover with a vacuum cleaner extension
hose.
5 Replace the air filter.
• Place the air filter underneath the tabs
on the filter cover.
6 Replace the filter cover.
• Slide the filter cover in the direction of
the arrow to close it.
Note
• Be sure the filter cover is securely
installed. The power will not turn on
unless it is correctly installed.
• If dust or dirt has collected inside the
bottom air filter (not removable), clean the
filter with a vacuum cleaner extension
hose.
Replacing the Air Filter
-82
Appendix
-83
Maintenance Indicators
■ The warning lights on the projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will
illuminate red, and the power will turn off. After the power has been turned off, follow the proce-
dures given below.
Temperature warning
indicator
Lamp replacement
indicator
Power indicator
About the temperature warning indicator
If the temperature inside the pro-
jector increases, due to blockage
of the air vents, or the setting lo-
cation, “
” will blink in the
lower left corner of the picture. If
the temperature keeps on rising,
the lamp will turn off and the tem-
perature warning indicator will
blink, the cooling fan will run for
further 90 seconds, then the power
will be shut off. After “
” ap-
pears, be sure to perform the fol-
lowing measures.
About the lamp
replacement indicator
■ The lamp life becomes 0%, when used
for approximately 2,000 hours with “ON”
in “Power Save” or when used for approxi-
mately 1,500 hours with “OFF” in “Power
Save” (see page 69).
■ When the remaining lamp life becomes
6% or less, “
” will be displayed on the
screen in yellow. When the percentage
becomes 0%, “ ” will change to “ ”
(red), the lamp will automatically turn off
and then the projector as well. At this time,
the lamp replacement indicator will illu-
minate in red.
■ If you try to turn on the projector a fourth
time without replacing the lamp, the pro-
jector will not turn on.
Maintenance indicator Condition Problem Possible Solution
Temperature
warning
indicator
Normal
Abnormal
Off
Red on/
Power off
The internal
temperature is
abnormally high.
Abnormal
• Blocked air intake
• Relocate the projector to an area
with proper ventilation.
• Cooling fan break-
down
• Internal circuit failure
• Clogged air intake
• Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page 96)
for repair.
Lamp
replacement
indicator
Red on/
Power off
The lamp does
not illuminate.
• Burnt-out lamp
• Lamp circuit failure
• Carefully replace the lamp. (See
page 86)
• Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page 96)
for repair.
• Please exercise care when
replacing the lamp.
Green on
Green
blinks
when the
lamp is
active.
Red blinks
/
Red on
Time to change
the lamp
• Remaining lamp life
becomes 6% or
under.
Power
indicator
The power
indicator blinks
in red when the
projector is on.
• The filter cover, lamp
unit cover or lens
cover is open.
• Securely install the covers.
• If the power indicator blinks even
when the filter cover is securely
installed, contact your nearest
Sharp Authorized Projector Dealer
or Service Center for advice.
Green on/
Red on
Red blinks
-84
Maintenance Indicators
Info
• If the temperature warning indicator illuminates, and the power turns off, follow the above possible solutions
and then wait until the projector has cooled down completely before plugging in the power cord and turning
the power back on. (At least 5 minutes.)
• If the power is turned off and then turned on again, as during a brief test, the lamp replacement indicator may
be triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet
and plug it back in again.
• If you want to clean the air vents during projector operation, be sure to first press
and after the power has
turned off and the cooling fan has stopped, then clean the vents.
• Do not unplug the power cord after the power has been turned off and while the cooling fan is running. The
cooling fan runs for about 90 seconds.
Appendix
-85
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life be-
comes 6% or less, or when you notice a significant deterioration in the picture and color quality. The
lamp life (percentage) can be checked with the on-screen display. See page 70.
■ For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service
Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-
rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
U.S.A. ONLY
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure
largely varies depending on the individual lamp and/or the condition and the frequency of use. It is
important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated or flash, it is rec-
ommended that the lamp be replaced with a new one immediately, even if the lamp appears to be
operating normally.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult with a doctor as soon as possible.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to remove the damaged lamp and assure safe operation.
Replacing the Lamp
Caution
• Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching
it can lead to burn or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
■ If the new lamp does not light after replacement, take your projector to the nearest Sharp Autho-
rized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQC-
XGC50X//1 from your nearest Sharp Authorized Projector Dealer or Service Center. Then carefully
change the lamp by following the instructions described in this section. If you wish, you may have
the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
Regarding the Lamp
Power (OFF) button
Lamp
unit
BQC-XGC50X//1
User service screw
Removing and Install-
ing the Lamp Unit
Info
• Be sure to remove the lamp unit by the
handle. Be sure not to touch the glass
surface of the lamp unit or the inside of
the projector.
• To avoid injury to yourself and damage
to the lamp, be sure to carefully follow
the steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
(Only the silver screws are loosened).
• Please refer to the installation manual
included with the lamp unit.
1 Press on the projector to
turn off the power.
• Wait until the cooling fan stops.
Warning!
• Do not remove the lamp unit from the
projector right after use. The lamp will
be very hot and may cause burn or
injury.
2 Disconnect the power cord.
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
3 Change the air filter.
• Change the air filter whenever you in-
stall the lamp unit (see pages 81 and
82).
4 Remove the lamp unit cover.
• Loosen the user service screw that
secures the lamp unit cover. Then
open the cover in the direction of the
arrow.
AC socket
-86
Regarding the Lamp
Appendix
-87
Securing
screw
AC socket
INPUT button
ENTER button
User service screw
UNDO buttom
Power (ON)
button
5 Remove the lamp unit.
• Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of
the arrow.
6 Insert the new lamp unit.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the secur-
ing screws.
7 Attach the lamp unit cover.
• Insert the tab of the lamp unit cover
into the opening, and press the cover
until it clicks in place.
Info
• If the lamp unit and lamp cover are not
correctly installed, the power will not turn
on, even if the power cord is connected
to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1 Connect the power cord.
• Plug the power cord into the AC socket
of the projector.
2 Reset the lamp timer.
•
While pressing simultaneously
,
and on the projector, press
ON
on the projector.
• “LAMP 100%” is displayed, indicating
that the lamp timer is reset.
Info
• Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
-88
RS-232C Terminal: 9-pin Mini DIN female connector
Pin No. Signal Name I/O Reference
1 VCC +3.3V (Reserved) Output Not connected
2 RD Receive Data Input Connected to internal circuit
3 SD Send Data Output Connected to internal circuit
4 EXIR Detector of Option Unit Input Not connected
(Reserved)
5 SG Signal Ground Connected to internal circuit
6 ERX IR Receive Signal from Input Not connected
IR Amplifier (Reserved)
7 RS Request to Send Output Not connected
8 CS Clear to Send Input Not connected
9 ETX IR Transmit Signal Output Not connected
(Reserved)
9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor
Pin No. Signal Name I/O Reference
1 CD Not connected
2 RD Receive Data Input Connected to internal circuit
3 SD Send Data Output Connected to internal circuit
4 ER Not connected
5 SG Signal Ground Connected to internal circuit
6 DR Data Set Ready Not connected
7 RS Request to Send Output Connected to internal circuit
8 CS Clear to Send Input Connected to internal circuit
9 CI Not connected
RS-232C Cable recommended connection: 9-pin D-sub female connector
Pin No. Signal Pin No. Signal
1CD 1 CD
2RD 2 RD
3SD 3 SD
4ER 4 ER
5SG 5 SG
6DR 6 DR
7RS 7 RS
8CS 8 CS
9CI 9 CI
Note
• Depending on the system layout, it is necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. PC).
USB Terminal: 4 pin B-type USB connector
Pin No. Signal Name
1 VCC USB power
2 USB– USB data–
3 USB+ USB data+
4 SG Signal Ground
INPUT 1/2 RGB and OUTPUT Signal Terminal: 15-pin Mini D-sub female connector
Connecting Pin Assignments
RGB Input
1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Reserve input 1
5. Composite sync
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. GND
12. Bi-directional data
13. Horizontal sync signal
14. Vertical sync signal
15. Data clock
Component Input
1. PR (CR)
2. Y
3. P
B
(C
B
)
4. Not connected
5. Not connected
6. Earth (P
R
)
7. Earth (Y)
8. Earth (P
B
)
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
Projector
Pin No.
4
5
6
PC
Pin No.
4
5
6
5
10
15
1
6
11
8
9
6
5
21
4
3
7
15
69
51
96
1
2
4
3
Appendix
-89
CONTROL CONTENTS
BLACK SCREEN ON
BLACK SCREEN OFF
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT CHECK
FREEZE ON
FREEZE OFF
AUTO SYNC START
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
I
I
I
I
I
I
I
F
F
A
M
M
R
R
V
V
C
R
R
D
B
B
G
G
E
E
H
E
E
J
K
K
B
B
D
D
K
Z
Z
S
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
0
1
2
1
2
0
1
0
1
BUTTONS & REMOTE CONTROL KEY
COMMAND
PARAMETER
RETURNCONTROL CONTENTS
POWER ON
POWER OFF
VOLUME (0 - 60)
MUTE ON
MUTE OFF
KEYSTONE (–127 - +127)
DIGITAL SHIFT (–96 - +96)
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
P
P
V
M
M
K
L
O
O
O
U
U
E
N
W
W
L
T
T
Y
D
R
R
A
E
E
S
S
_
_
_
_
_
*
_
_
_
_
_
_
*
*
_
_
*
_
_
*
*
1
0
*
1
0
*
*
BUTTONS & REMOTE CONTROL KEY
COMMAND
PARAMETER
RETURN
PC control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,
sold separately) to the projector. (See page 23 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Info
• When more than one code is being sent, send each command only after the response code for the previous
command from the projector is verified.
• In the case of transmitting commands during standby, it takes a maximum of 30 seconds until the response
code is received.
• When the power is turned on during standby with the “POWER ON” command, wait for at least 30 seconds
after the power has been turned on, and then transmit the next command.
Note
• When using the computer control function of the projector, the projector’s operating status cannot be read by
the computer. Therefore, confirm the status by transmitting the display commands for each adjustment
menu and checking the status with the on-screen display. If the projector receives a command other than a
menu display command, it will execute the command without displaying the on-screen display.
Commands
Example:
• When “BRIGHT” of INPUT 1 image adjustment is set to –10.
Return code (0DH)
C1 C2 C3 C4 P1 P2 P3 P4
Response code format
Normal response
Problem response (communication error or incorrect command)
O K E R R
Command 4-digit Parameter 4-digit
Command format
Return code (0DH)
Return code (
0DH)
(RS-232C) Specifications and Command Settings
→
←
RABR 1 0_– OK
ProjectorComputer
-90
CONTROL CONTENTS
INPUT 1 RESIZE : NORMAL
INPUT 1 RESIZE : FULL
INPUT 1 RESIZE : DOT BY DOT
INPUT 1 RESIZE : STRETCH
INPUT 1 RESIZE : SMART STRETCH
INPUT 2 RESIZE : NORMAL
INPUT 2 RESIZE : FULL
INPUT 2 RESIZE : DOT BY DOT
INPUT 2 RESIZE : STRETCH
INPUT 2 RESIZE : SMART STRETCH
INPUT 3 RESIZE : NORMAL
INPUT 3 RESIZE : BORDER
INPUT 3 RESIZE : STRETCH
INPUT 3 RESIZE : SMART STRETCH
INPUT 4 RESIZE : NORMAL
INPUT 4 RESIZE : BORDER
INPUT 4 RESIZE : STRETCH
INPUT 4 RESIZE : SMART STRETCH
RGB GAMMA : STANDARD
RGB GAMMA : PRESENTATION
RGB GAMMA : CINEMA
RGB GAMMA : CUSTOM
VIDEO GAMMA : STANDARD
VIDEO GAMMA : PRESENTATION
VIDEO GAMMA : CINEMA
VIDEO GAMMA : CUSTOM
INPUT 1 CONTRAST (–30 - +30)
INPUT 1 BRIGHT (–30 - +30)
INPUT 1 RED (–30 - +30)
INPUT 1 BLUE (–30 - +30)
INPUT 1 COLOR (–30 - +30)
INPUT 1 TINT (–30 - +30)
INPUT 1 SHARP (–30 - +30)
INPUT 1 CLR TEMP (–3 - +3)
INPUT 1 DISPLAY
INPUT 1 ADJUSTMENT RESET
INPUT 2 CONTRAST (–30 - +30)
INPUT 2 BRIGHT (–30 - +30)
INPUT 2 RED (–30 - +30)
INPUT 2 BLUE (–30 - +30)
INPUT 2 COLOR (–30 - +30)
INPUT 2 TINT (–30 - +30)
INPUT 2 SHARP (–30 - +30)
INPUT 2 CLR TEMP (–3 - +3)
INPUT 2 DISPLAY
INPUT 2 ADJUSTMENT RESET
INPUT 1 SIGNAL TYPE : RGB
INPUT 1 SIGNAL TYPE : COMPONENT
INPUT 2 SIGNAL TYPE : RGB
INPUT 2 SIGNAL TYPE : COMPONENT
INPUT 1 2D PROGRESSIVE
INPUT 1 3D PROGRESSIVE
INPUT 1 FILM MODE
INPUT 2 2D PROGRESSIVE
INPUT 2 3D PROGRESSIVE
INPUT 2 FILM MODE
INPUT 3 CONTRAST (–30 - +30)
INPUT 3 BRIGHT (–30 - +30)
INPUT 3 RED (–30 - +30)
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
G
G
G
G
G
G
G
G
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
I
I
I
I
R
R
R
R
R
R
V
V
V
A
A
A
A
A
B
B
B
B
B
A
A
A
A
B
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
A
A
B
B
A
A
A
B
B
B
A
A
A
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
M
M
M
M
M
M
M
M
P
B
R
B
C
T
S
C
R
R
P
B
R
B
C
T
S
C
R
R
S
S
S
S
I
I
I
I
I
I
P
B
R
R
R
R
R
R
R
R
R
R
R
V
V
V
V
V
V
V
V
R
R
R
R
V
V
V
V
I
R
D
E
O
I
H
T
E
E
I
R
D
E
O
I
H
T
E
E
I
I
I
I
P
P
P
P
P
P
I
R
D
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
_
_
_
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
*
_
_
*
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
1
5
3
2
4
1
5
3
2
4
1
3
2
4
1
3
2
4
1
2
3
4
1
2
3
4
*
*
*
*
*
*
*
*
0
1
*
*
*
*
*
*
*
*
0
1
1
2
1
2
0
1
2
0
1
2
*
*
*
BUTTONS & REMOTE CONTROL KEYPICTURE
COMMAND
PARAMETER
RETURN CONTROL CONTENTS
INPUT 3 BLUE (–30 - +30)
INPUT 3 COLOR (–30 - +30)
INPUT 3 TINT (–30 - +30)
INPUT 3 SHARP (–30 - +30)
INPUT 3 CLR TEMP (–3 - +3)
INPUT 3 DISPLAY
INPUT 3 ADJUSTMENT RESET
INPUT 4 CONTRAST (–30 - +30)
INPUT 4 BRIGHT (–30 - +30)
INPUT 4 RED (–30 - +30)
INPUT 4 BLUE (–30 - +30)
INPUT 4 COLOR (–30 - +30)
INPUT 4 TINT (–30 - +30)
INPUT 4 SHARP (–30 - +30)
INPUT 4 CLR TEMP (–3 - +3)
INPUT 4 DISPLAY
INPUT 4 ADJUSTMENT RESET
INPUT 3 2D PROGRESSIVE
INPUT 3 3D PROGRESSIVE
INPUT 3 FILM MODE
INPUT 4 2D PROGRESSIVE
INPUT 4 3D PROGRESSIVE
INPUT 4 FILM MODE
COLOR SELECTED : STANDARD
COLOR SELECTED : sRGB
COLOR SELECTED : CUSTOM 1
COLOR SELECTED : CUSTOM 2
COLOR SELECTED : CUSTOM 3
TARGET : RED
TARGET : YELLOW
TARGET : GREEN
TARGET : CYAN
TARGET : BLUE
TARGET : MAGENTA
LIGHTNESS (–30 - +30)
CHROMA (–30 - +30)
HUE (–30 - +30)
Reset (THIS COLOR)
Reset (All COLORS)
CLOCK (–150 - +150)
PHASE (–30 - +30)
H-POSITION (–150 - +150)
V-POSITION (–60 - +60)
RGB INPUT DISPLAY
RGB ADJUSTMENT RESET
SAVE SETTING (1 - 7)
SELECT SETTING (1 - 7)
RGB HORIZONTAL FREQUENCY CHECK
RGB VERTICAL FREQUENCY CHECK
AUTO SYNC OFF
NORMAL AUTO SYNC
HIGH SPEED AUTO SYNC
AUTO SYNC DISPLAY ON
AUTO SYNC DISPLAY OFF
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
kHz (***. * OR _)
Hz (***. * OR _)
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
I
I
I
I
I
I
M
M
T
T
A
A
A
I
I
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
A
A
A
B
B
B
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
N
N
A
A
A
A
E
E
F
F
A
A
A
M
M
B
C
T
S
C
R
R
P
B
R
B
C
T
S
C
R
R
I
I
I
I
I
I
C
C
C
C
C
T
T
T
T
T
T
S
S
S
R
R
C
P
H
V
R
R
M
M
R
R
D
D
D
A
A
E
O
I
H
T
E
E
I
R
D
E
O
I
H
T
E
E
P
P
P
P
P
P
S
S
S
S
S
G
G
G
G
G
G
L
C
H
E
E
L
H
P
P
E
E
S
L
Q
Q
J
J
J
S
S
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
_
*
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
_
_
_
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
_
_
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
_
_
*
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
0
0
1
1
1
_
_
_
_
_
_
*
*
*
_
_
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
0
1
*
*
*
*
*
*
*
*
0
1
0
1
2
0
1
2
0
1
1
2
3
1
2
3
4
5
6
*
*
*
1
2
*
*
*
*
0
1
*
*
1
2
0
1
2
1
0
PICTUREFINE SYNC
*1
COMMAND
PARAMETER
RETURN
C. M. S.
(RS-232C) Specifications and Command Settings
Appendix
-91
CONTROL CONTENTS
FAO
VAO
SPEAKER ON
SPEAKER OFF
PICT IN PICT : BOTTOM RIGHT
PICT IN PICT : BOTTOM LEFT
PICT IN PICT : UPPER RIGHT
PICT IN PICT : UPPER LEFT
PICT IN PICT OFF
POWER SAVE: STANDARD
POWER SAVE: LOW POWER
DNR: OFF
DNR: LEVEL 1
DNR: LEVEL 2
DNR: LEVEL 3
AUTO SEARCH: OFF
AUTO SEARCH: ON
OSD DISPLAY NORMAL
OSD DISPLAY LEVEL A
OSD DISPLAY LEVEL B
BLACK SCREEN DISPLAY ON
BLACK SCREEN DISPLAY OFF
VIDEO SYSTEM SELECTION : AUTO
VIDEO SYSTEM SELECTION : PAL (50/60 Hz)
VIDEO SYSTEM SELECTION : SECAM
VIDEO SYSTEM SELECTION : NTSC4.43
VIDEO SYSTEM SELECTION : NTSC3.58
VIDEO SYSTEM SELECTION : PAL_M
VIDEO SYSTEM SELECTION : PAL_N
BACKGROUND SELECTION : SHARP
BACKGROUND SELECTION : CUSTOM
BACKGROUND SELECTION : BLUE
BACKGROUND SELECTION : NONE
STARTUP IMAGE SELECTION : SHARP
STARTUP IMAGE SELECTION : CUSTOM
STARTUP IMAGE SELECTION : NONE
AUTO POWER OFF : NO USE
AUTO POWER OFF : USE
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
A
A
A
A
P
P
P
P
P
T
T
3
3
3
3
I
I
I
I
I
I
I
M
M
M
M
M
M
M
I
I
I
I
I
I
I
A
A
O
O
S
S
I
I
I
I
I
H
H
D
D
D
D
N
N
M
M
M
M
M
E
E
E
E
E
E
E
M
M
M
M
M
M
M
P
P
U
U
P
P
N
N
N
N
N
M
M
N
N
N
N
S
S
D
D
D
B
B
S
S
S
S
S
S
S
B
B
B
B
S
S
S
O
O
T
T
K
K
P
P
P
P
P
D
D
R
R
R
R
E
E
I
I
I
O
O
Y
Y
Y
Y
Y
Y
Y
G
G
G
G
I
I
I
W
W
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
1
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
2
1
0
1
2
3
4
0
0
1
0
1
2
3
0
1
1
2
0
1
0
1
2
3
4
5
6
7
1
2
3
4
1
2
3
0
1
OPTIONS (1)
COMMAND
PARAMETER
RETURN
CONTROL CONTENTS
LAMP LIFE (PERCENTAGE)
LAMP STATUS
PRJ MODE : REVERSE OFF
PRJ MODE : REVERSE ON
PRJ MODE : INVERT OFF
PRJ MODE : INVERT ON
KEYLOCK LEVEL : NORMAL
KEYLOCK LEVEL : LEVEL A
KEYLOCK LEVEL : LEVEL B
LANGUAGE SELECTION : ENGLISH
LANGUAGE SELECTION : DEUTSCH
LANGUAGE SELECTION : ESPAÑOL
LANGUAGE SELECTION : NEDERLANDS
LANGUAGE SELECTION : FRANÇAIS
LANGUAGE SELECTION : ITALIANO
LANGUAGE SELECTION : SVENSKA
LANGUAGE SELECTION :
LANGUAGE SELECTION : PORTUGUÊS
LANGUAGE SELECTION :
LANGUAGE SELECTION :
MODEL NAME CHECK
SERIAL NO. CHECK
*2
PROJECTOR NAME SETTING 1
(First four characters)
PROJECTOR NAME SETTING 2
(Middle four characters)
PROJECTOR NAME SETTING 3
(Last four characters)
PROJECTOR NAME CHECK
0-100 (INTEGER)
0:OFF, 1:ON, 2:RETRY,
3:WAITING, 4:LAMP ERROR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
MODEL NAME
SERIAL NO.
OK OR ERR
OK OR ERR
OK OR ERR
PROJECTOR NAME
T
T
I
I
I
I
K
K
K
M
M
M
M
M
M
M
M
M
M
M
M
S
P
P
P
P
L
L
M
M
M
M
E
E
E
E
E
E
E
E
E
E
E
E
E
E
N
N
J
J
J
J
T
P
R
R
I
I
Y
Y
Y
L
L
L
L
L
L
L
L
L
L
L
R
R
N
N
N
N
L
S
E
E
N
N
L
L
L
A
A
A
A
A
A
A
A
A
A
A
D
D
1
2
3
0
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
_
_
*
*
*
_
1
1
0
1
0
1
0
1
2
1
2
3
4
5
6
7
8
9
0
1
1
1
*
*
*
1
OPTIONS (2)LANGUAGE
COMMAND
PARAMETER
RETURN
Note
• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value
in the range indicated in brackets under CONTROL CONTENTS.
•
*1
FINE SYNC can only be set in the displayed RGB mode.
•
*2
SERIAL NO. CHECK command is used to read out the 12 digits of serial No..
-92
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ON
OFF
VOLUME +
VOLUME –
MUTE
MENU
KEYSTONE
BLACK SCREEN
ENTER
RESIZE
UNDO
FREEZE
ENLARGE (+)
ENLARGE (–)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
1
1
0
1
1
1
1
1
1
0
0
1
0
1
0
1
1
0
0
0
0
1
1
1
1
1
1
0
0
1
1
0
1
1
1
0
0
0
0
0
0
1
1
0
1
1
1
1
1
1
1
1
1
1
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
0
0
0
0
1
0
1
1
1
1
0
1
0
0
1
0
0
0
1
1
0
0
0
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AUTO SYNC
∂
ƒ
ß
©
GAMMA
PinP
BACK
FORWARD
BREAK TIMER
INPUT 1
INPUT 2
INPUT 3
INPUT 4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
1
0
1
0
1
0
0
1
1
0
0
0
1
0
1
1
1
0
0
1
1
1
0
1
1
0
1
0
1
1
1
1
1
1
0
0
1
1
1
0
1
0
1
1
1
0
0
0
0
0
1
1
1
1
0
0
1
0
0
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Wired Remote Control Terminal Specifications
Specifications of wired remote control input
• ø3.5 mm minijack
• External: +5 V (1 A)
• Internal: GND
Function and transmisson codes
Sharp remote control signal format
Transmission format: 15-bit format
Wave form of output signal: Output using Pulse Position Modulation
• t = 264 µs • Pulse carrier frequency = 455/12 kHz
• T
0 = 1.05 ms • Duty ratio = 1:1
• T
1 = 2.10 ms
Transmission control code
15 bit Example of Reverse D to D
Wired remote control function code
LSB MSB
• System codes C1 to C5 are fixed at “10110”.
• Codes C14 and C15 are reverse confirmation bits, with “10” indicating “Front” and “01” indicating “Rear”.
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14
System Address
D to D Common Data Bit Reverse in D
Function Key Data Bit
Data
Expansion
Data
Deter-
mination
Mask
C15
C1
1
DC2
0
C3
1
C4
1
C5
0
C6
1
C7
0
C8
0
C9
0
C10
0
C11
0
C12
0
C13
0
C14
1
C15
0
C1
1
DC2
0
C3
1
C4
1
C5
0
C6
0
C7
1
C8
1
C9
1
C10
1
C11
1
C12
1
C13
1
C14
0
C15
1
“0”“1”“0”
D
“0”“0”“0”“1”
T
0
T
1
t
t
26.4 µs
DDDDDD
DDDDDDD
67.5 ms 67.5 ms
10110********10
C1 System Code C5 C6 Data Code C13 C14 C15
Appendix
-93
Computer Compatibility Chart
Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off
the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change display modes can
be found in your notebook computer’s operation manual.
• When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.
•
When receiving 1,600 × 1,200 VESA format signals, sampling occurs and part of the image may be cut as the image is displayed in 1,024 lines.
• Multiple signal support
Horizontal Frequency: 15–126 kHz, Vertical Frequency: 43–200 Hz*, Pixel Clock: 12–230 MHz
• Compatible with sync on green and composite sync signals
• UXGA and SXGA compatible in advanced intelligent compression
• AICS (Advanced Intelligent Compression and Expansion System) resizing technology
The following is a list of modes that conform to VESA. However, this projector supports other signals
that are not VESA standards.
Upscale
True
640 × 350
720 × 350
640 × 400
720 × 400
640 × 480
800 × 600
1,024 × 768
31.5
37.9
27.0
31.5
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
47.9
53.0
61.8
78.5
80.9
100.4
31.4
35.1
37.9
44.5
48.1
46.9
53.7
56.8
64.0
77.2
98.3
102.1
125.6
70
85
60
70
60
70
85
60
70
85
60
70
72
75
85
90
100
120
160
200
50
56
60
70
72
75
85
90
100
120
150
160
200
✔
PC
XGA
SVGA
VGA
50
150
35.5
40.3
48.4
56.5
58.1
60.0
68.7
73.5
77.2
80.6
98.8
113.2
43
50
60
70
72
75
85
90
96
100
120
140
Display
PC/
MAC/
WS
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
VESA
Standard
27.0 60
1,152 × 864
1,152 × 882
1,280×1,024
54.3
64.0
64.1
67.5
60
70
72
75
SXGA
77.3
90.2
54.8
65.9
67.4
64.0
74.6
85
100
60
72
74
60
70
1,280
×
1,024
Advanced
Intelligent
Compression
75.7 80
1,400 ×1,050
SXGA
+
Display
PC/
MAC/
WS
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
78.1 74
80.0 75
91.1 85
108.4 100
64.0 60
74.7 52
75.0 60
81.3 65
87.5 70
90.1 72
93.8 75
106.3 85
640 × 480 34.9 67
48.4 60
60.0 75
80.0 75
46.8 75
49.6 75
68.5 75
78.1 72
60.0 60
85.9 85
53.5 50
76.8 72
60.9 66
71.9 76
UXGA
1,600
×
1,200
VGA
XGA
SXGA
SVGA
1,024 × 768
800
×
600
832
×
624
1,152
×
870
1,280×1,024
SXGA
1,280
×
960
1,280×1,024
1,152
×
900
HP (WS)
PC (WS)
WS
SGI (WS)
SUN (WS)
PC/
MAC 21”
MAC
16”
PC/
MAC 13”
PC/
MAC 19”
SXGA
PC
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
VESA
Standard
Upscale
Tr u e
Advanced
Intelligent
Compression
Upscale
Advanced
Intelligent
Compression
Intelligent
Compression
* Temporary noise may be visible with vertical frequencies
above 100Hz if OSD functions are activated.
DTV
Computer
Signal
480I
480P
540P
580I
580P
720P
1035I
1080I
1080I
Horizontal Frequency (kHz)
15.7
31.5
33.8
15.6
31.3
45.0
33.8
33.8
28.1
Vertical Frequency (Hz)
60
60
60
50
50
60
60
60
50
-94
Troubleshooting
Check
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
• Cables incorrectly connected to rear panel of the projector.
• Remote control batteries have run out.
•
External output has not been set when connecting notebook computer.
• The cover of the lamp unit is not installed correctly.
• Cables incorrectly connected to the rear panel of the projector.
• “Bright” is set to minimum position.
• Picture adjustments are incorrectly set.
(Video Input only)
• Video input system is incorrectly set.
(INPUT 1 and 2 only)
• Input signal type (RGB/Component) is incorrectly set.
• Adjust the focus.
• The projection distance exceeds the focus range.
(Computer Input only)
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)
• Noise will appear depending on the computer.
• The “DNR” (Digital Noise Reduction) setting is not correct.
• Cables incorrectly connected to rear panel of projector.
• Volume is set to minimum.
• The MUTE display appears.
• If the picture is normal, the sound is due to cabinet shrinkage
caused by a room temperature changes. This will not affect
operation or performance.
• See “Maintenance Indicators”.
• The signal in INPUT 1 or 2 is not an RGB XGA (1024 × 768)
signal. Images cannot be captured if the signals are different
from the above.
Problem
An unusual sound is
occasionally heard
from the cabinet.
Maintenance
indicator illuminates.
Image cannot be
captured.
Page
17
—
35
18
13
18
87
18
46
46
66
46
28
29
48
48
—
65
18
35
36
—
83
67
Sound is heard but no
picture appears.
Color is faded or poor.
Picture is blurred;
noise appears.
Picture appears but no
sound is heard.
No picture and no sound
or projector does not start.
Appendix
-95
CheckProblem Page
Pict in Pict does not
work.
Power cannot be turned
on or off using the power
buttons on the projector.
Picture is green on
INPUT 1 or 2
COMPONENT.
Picture is pink (no green)
on INPUT 1 or 2 RGB.
Picture is dark.
Picture is too bright and
whitish.
The VOLUME buttons
on the projector do not
work.
A response code cannot
be received when the
projector was attempted
to be controlled using
RS-232C commands
from a computer during
standby.
• The signal in INPUT 1 or 2 is set to a resolution that exceeds
SXGA.
• The signal in INPUT 1 or 2 is sending Component signals 480I,
480P, 540P, 580I, 580P, 720P, 1035I or 1080I.
• The signal in INPUT 1 or 2 is set to interlace mode using RGB
signals.
• The Keylock level is set.
If the Keylock level is set to Level B, all the buttons are locked.
If the Keylock level is set to Level A, only the INPUT and
VOLUME buttons are functional.
• Change the input signal type setting.
• The lamp replacement indicator is blinking in red. Replace the
lamp.
• Picture adjustments are incorrectly set.
The VOLUME buttons do not work when: (try the VOL+/– on the
remote control)
• when the menu is displayed
• when the lens menu is displayed
• when Pict in Pict is working
• during Enlarge (More than double size)
• a dot by dot screen resolution larger the panel resolution
• In the case of transmitting RS-232C commands from a
computer during standby, it takes a maximum of 30 seconds for
the computer to receive the response code. Set the response
code waiting time of the computer to 30 seconds or more.
57
71
46
83
46
—
89
Troubleshooting
-96
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first refer to the
“Troubleshooting” section on pages 94 and 95. If this operation manual does not answer
your question, please contact the SHARP Service departments listed below.
U.S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
lcdsupport@sharpsec.com
http://www.sharplcd.com
Canada Sharp Electronics of Canada Ltd.
(905) 568-7140
http://www.sharp.ca
Mexico Sharp Electronics Corporation Mexico
Branch
(525) 716-9000
http://www.sharp.com.mx
Latin America Sharp Electronics Corp. Latin American
Group
(305) 264-2277
www.servicio@sharpsec.com
http://www.siempresharp.com
Germany Sharp Electronics (Europe) GMBH
01805-234675
http://www.sharp.de
U.K. Sharp Electronics (U.K.) Ltd.
0161-205-2333
custinfo@sharp-uk.co.uk
http://www.sharp.co.uk
Italy Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
http://www.sharp.it
France Sharp Electronics France
01 49 90 35 40
hotlineced@sef.sharp-eu.com
http://www.sharp.fr
Spain Sharp Electronica Espana, S.A.
93 5819700
sharplcd@sees.sharp-eu.com
http://www.sharp.es
Switzerland Sharp Electronics (Schweiz) AG
0041 1 846 63 11
cattaneo@sez.sharp-eu.com
http://www.sharp.ch
Sweden Sharp Electronics ( Nordic ) AB
(46) 8 6343600
vision.support@sen.sharp-eu.com
http://www.sharp.se
Benelux SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
http://www.sharp.nl
http://www.sharp.be
http://www.sharp.lu
Austria Sharp Electronics Austria
(Ges.m.b.H.)
0043 1 727 19 123
pogats@sea.sharp-eu.com
http://www.sharp.at
Australia Sharp Corporation of Australia
Pty. Ltd.
1300-135-022
http://www.sharp.net.au
New Zealand Sharp Corporation of New Zealand
(09) 634-2059, (09) 636-6972
http://www.sharpnz.co.nz
Singapore Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
ckng@srs.global.sharp.co.jp
http://www.sharp.com.sg
Hong Kong Sharp-Roxy (HK) Ltd.
(852) 2410-2623
dcmktg@srh.global.sharp.co.jp
http://www.sharp.com.hk
Malaysia Sharp-Roxy Sales & Service Co.
(60) 3-5125678
U.A.E. Sharp Middle East Fze
971-4-81-5311
helpdesk@smef.global.sharp.co.jp
Thailand Sharp Thebnakorn Co. Ltd.
02-236-0170
svc@stcl.global.sharp.co.jp
http://www.sharp-th.com
Korea Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
webmaster@sharp-korea.co.kr
http://www.sharp-korea.co.kr
India Sharp Business Systems (India)
Limited
(91) 11- 6431313
service@sharp-oa.com
Appendix
-97
Specifications
LCD Projector
PG-C45X
NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM/
DTV480I/DTV480P/DTV540P/DTV580I/DTV580P/DTV720P/DTV1035I/DTV1080I
LCD panel × 3, RGB optical shutter method
Panel size: 0.99" (25.1 mm) (15 [H] × 20 [W] mm)
No. of dots: 786,432 dots (1,024 [H] × 768 [V])
1–1.27 × zoom lens, F1.7–2.2, f = 36.5–46.3 mm
AC 250 W lamp
15-pin mini D-sub connector
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
P
B
: 0.7 Vp-p, 75 Ω terminated
P
R
: 0.7 Vp-p, 75 Ω terminated
750 TV lines (DTV720P)
15-pin mini D-sub connector
RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
4-pin Mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
9-pin mini DIN connector
12–230 MHz
43–200 Hz*
15–126 kHz
ø3.5 mm minijack: AUDIO, 0.5 Vrms, more than 47 kΩ (stereo)
3.0 W (monaural)
4 cm × 7 cm
AC 100–240 V
3.4 A
50/60 Hz
340 W (Standard mode)/290 W (Low power mode)
About 0.8 W (When “Mntr.out/RS232” is set to “OFF”)
1,280 BTU/hour
41°F to 104°F (+5°C to +40°C)
–4°F to 140°F (–20°C to +60°C)
Plastic
38 kHz
15
3
⁄8" × 3
7
⁄8" × 11
9
⁄16" (390 (W) × 99.0 (H) × 294 (D) mm) (main body only)
15
1
⁄2" × 4
7
⁄16" × 11
5
⁄8" (393 (W) × 114.0 (H) × 303.2 (D) mm) (including adjustment foot
and projecting parts)
11.3 lbs. (5.1 kg)
Remote control, Two R-6 batteries, Power cord for U.S., Canada etc. (11'10", 3.6 m), Power
cord for Europe, except U.K. (6', 1.8 m), Power cord for U.K., Hong Kong and Singapore (6',
1.8 m), Power cord for Australia, New Zealand and Oceania (6', 1.8 m), RGB cable (9'10", 3
m), USB cable (9'10", 3 m), Computer audio cable (9'10", 3 m), DIN-D-sub RS-232C adap-
tor (6
45
⁄64"
, 15 cm), Extra air filter, Lens cap (attached), Projector manual and technical
reference CD-ROM, Sharp Advanced Presentation Software CD-ROM, Operation manual,
Quick reference label
Lamp unit (Lamp/cage module) (BQC-XGC50X//1), Remote control (RRMCGA029WJSA),
Two R-6 batteries (“AA” size, UM/SUM-3, HP-7, or similar), Power cord for U.S., Canada etc.
(QACCDA010WJPZ), Power cord for Europe, except U.K. (QACCV4002CEZZ), Power cord
for U.K., Hong Kong and Singapore (QACCBA012WJPZ), Power cord for Australia, New
Zealand and Oceania (QACCL3022CEZZ), RGB cable (QCNWGA012WJPZ), USB cable
(QCNWGA014WJPZ), Computer audio cable (QCNWGA013WJPZ), DIN-D-sub RS-232C
adaptor (QCNWGA015WJPZ), Air filter (PFILDA005WJZZ), Lens cap (PCAPHA003WJSA),
Projector manual and technical reference CD-ROM (UDSKAA016WJZZ), Sharp Advanced
Presentation Software CD-ROM (UDSKAA017WJZZ), Operation manual (TINS-A428WJZZ),
Quick reference label
Product type
Model
Video system
Display method
LCD panel
Standard lens
Projection lamp
Component input signal
(INPUT1/2)
Horizontal resolution
Computer RGB input signal
(INPUT 1/2)
Video input signal
(INPUT 3)
S-video input signal
(INPUT 4)
Computer control signal (RS-232C)
Pixel clock
Vertical frequency
Horizontal frequency
Audio input signal
Audio output
Speaker system
Rated voltage
Input current
Rated frequency
Power consumption (normal)
Power consumption (standby)
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
This SHARP projector uses a LCD (Liquid Crystal Display)
panel. This very sophisticated panel contains 786,432 pix-
els (× RGB) TFTs (Thin Film Transistors). As with any high
technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain accept-
able tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable toler-
ances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life ex-
pectancy of the unit.
* Temporary noise may be visible with vertical frequencies above 100Hz if OSD functions are activated.
Specifications are subject to change without notice.
-98
Dimensions
Side View Side ViewTop View
Rear View
Front View
Bottom View
3
15
/
16
(100.5)9
1
/
2
(241.5)
15
3
/
8
(390)
5 (126.5)
1
/
16
(1.5)
1
/
16
(1.5)
3
1
/
8
(80)
ø 67.5
4
3
/
8
(111.75)
2
15
/
16
(75)
M4
M4
M4
M4
2
11
/16 (67.5)
4
15
/
16
(124.5)
5
/
16
(7.5)
3
15
/
16
(99)
8
7
/
16
(213.3)
11
9
/
16
(294)
3
/
16
(5.2)
1
/
8
(4)
9
/
16
(15)
2
1
/
8
(54.5)
1
3
/
4
(44.5)
4
1
/
8
(104)
Units: inches (mm)
Appendix
-99
Glossary
Advanced intelligent compression
High quality resizing of lower and higher resolu-
tion images to fit the projector’s native resolution.
Anti-theft
If the “Keycode” set in the projector is not cor-
rectly entered, the projector will not operate even
if signals are entered.
Aspect Ratio
Width and height ratio of an image. The normal
aspect ratio of a computer and video image is 4:3.
There are also wide images with an aspect ratio
of 16:9 and 21:9.
Auto Sync
Optimizes projected computer images by auto-
matically adjusting certain characteristics.
Background
Initial setting image projected when no signal is
being output.
Border
Projects a 4:3 image fully within a 16:9 screen by
keeping the aspect ratio at 4:3.
Clock
Clock adjustment is used to adjust vertical noise
when clock level is incorrect.
CLR Temp (Color temperature)
Function that can be used to adjust the color tem-
perature to suit the type of image input to the pro-
jector. Decrease the color temperature to create
warmer, reddish images for natural flesh tones,
or increase to create cooler, bluish images for a
brighter picture.
C.M.S. (Color Management System)
Function allows you individually adjust the display
characteristics of six colors (R: Red, Y: Yellow, G:
Green, C: Cyan, B: Blue, M: Magenta)
Digital Shift Setting
Shifts image up or down easily by ', " buttons
when RESIZE mode of input image is BORDER,
STRETCH or SMART STRETCH of the video or
the DTV signals.
Dot by dot
Mode that projects images in their native resolution.
Gamma
Image quality enhancement function that offers a
richer image by brightening the darker portions of
the image without altering the brightness of the
brighter portions. You can select four different
modes: STANDARD, PRESENTATION, CINEMA
and CUSTOM.
Keylock Level
Mode that can lock the operation of projector but-
tons to prevent mischief.
Keystone correction
Function to digitally correct a distorted image
when the projector is set up at an angle, smooth-
ens out jaggies on keystone images and com-
presses the image not only horizontally but verti-
cally keeping the 4:3 aspect ratio.
Notevision Lock Down
A new ceiling mounting mechanism that is ef-
fective in anti-theft and realizing improved in-
stallation strength.
Password
A password is set so that changes cannot be made
in the settings of the “Options (2)” menu.
Phase
Phase shift is a timing shift between isomorphic
signals with the same resolution. When phase
level is incorrect, the projected image typically
displays horizontal flicker.
Picture in Picture
Allows you to add video images onto a data screen
image, providing you with even more effective pre-
sentations.
Progressive Mode
The progressive display projects a smoother video
image. You can select three different modes: 2D
Progressive, 3D Progressive and Film Mode.
Resize
Allows you to modify or customize the picture dis-
play mode to enhance the input image. You can
select six different modes: NORMAL, FULL, DOT
BY DOT, BORDER, STRETCH and SMART
STRETCH.
Smart Stretch
Projects the image fully in a 16:9 screen by en-
larging only the surrounding areas while keeping
the aspect ratio in the middle part of the image at
4:3.
sRGB
An international standard of color reproduction
regulated by the IEC (International
Electrotechnical Commission). As the fixed color
area has been decided by the IEC, the color
changes according to LCD features, so that the
images are displayed in a natural tint based on
an original image, when switching to the “sRGB”
mode.
Stretch
Mode that stretches the 4:3 image horizontally to
display it fully on a 16:9 screen.
-100
2D Progressive .................................................... 47
3D Progressive .................................................... 47
AC socket ............................................................. 17
Adjusting Computer Images ................................ 48
Adjusting the Lens ............................................... 28
Adjusting the Picture ............................................ 46
Adjustment buttons .............................................. 42
Adjustment feet .................................................... 27
Air filter ................................................................. 81
All Reset .............................................................. 77
Anti-Theft ............................................................. 75
Aspect ratio .......................................................... 52
AUDIO input 1, 2 terminal .................................... 18
AUDIO (L/R) input 3, 4 terminals......................... 20
AUDIO OUTPUT terminal .................................... 22
Auto Power off...................................................... 70
Auto Search ......................................................... 64
Auto Sync adjustment .......................................... 50
AUTO SYNC button ............................................. 50
Auto Sync Disp .................................................... 50
BACK button ........................................................ 25
Background .......................................................... 68
Batteries ............................................................... 13
BLACK SCREEN button ...................................... 58
BORDER .............................................................. 53
BREAK TIMER button ......................................... 59
Carrying handle ................................................... 10
Ceiling-mount setup ............................................. 32
Chroma ................................................................ 61
Clock .................................................................... 48
CLR Temp (Color Temperature)........................... 46
C.M.S. .................................................................. 60
Color Selected ..................................................... 60
Computer audio cable ......................................... 18
Digital Shift Setting .............................................. 39
DIN-D-sub RS-232C adaptor .............................. 23
DNR ..................................................................... 65
DOT BY DOT ....................................................... 52
ENLARGE buttons ............................................... 55
ENTER button ...................................................... 42
Exhaust vent ........................................................ 80
FAO ...................................................................... 63
Film Mode ............................................................ 47
Fine Sync ............................................................. 48
Focus ring ............................................................ 28
FORWARD button ............................................... 25
FREEZE button .................................................... 54
FULL .................................................................... 52
Index
GAMMA button .................................................... 56
HEIGHT ADJUST button ..................................... 27
Hue ...................................................................... 61
Image Capture ..................................................... 67
INPUT 1 terminal ................................................. 18
INPUT 1 – 4 modes ............................................. 35
INPUT 2 terminal ................................................. 18
INPUT 3 terminal ................................................. 20
INPUT 4 terminal ................................................. 20
INPUT button ....................................................... 34
Intake vent ........................................................... 80
Kensington Security Standard connector ............ 11
Keylock level ........................................................ 71
KEYSTONE button .............................................. 38
Keystone correction ............................................. 38
Lamp .................................................................... 85
Lamp Life ............................................................. 70
Lamp replacement indicator ................................ 83
Lens cap .............................................................. 10
Lightness ............................................................. 61
MENU button ....................................................... 42
MUTE button ........................................................ 36
NORMAL .............................................................. 52
Optional cables .................................................... 14
OSD Display ........................................................ 65
OUTPUT (INPUT 1, 2) terminal .......................... 69
Password ............................................................. 73
PDF ........................................................................ 9
Phase ................................................................... 48
Pict in Pict ............................................................ 57
PinP button .......................................................... 57
Power buttons ...................................................... 34
Power cord ........................................................... 17
Power indicator .................................................... 34
Power Save .......................................................... 69
PRJ mode ............................................................ 71
Progressive Mode ................................................ 47
Remote control .................................................... 12
Remote control sensor ........................................ 13
Replacing the lamp .............................................. 85
RESIZE button ..................................................... 52
Reversing/Inverting Projected Images ................ 71
RGB cable............................................................ 18
RS-232C terminal ................................................ 23
Appendix
-101
Save Setting......................................................... 48
Select Setting....................................................... 49
Selecting the on-screen display language .......... 36
Signal Info ............................................................ 49
Signal Type .......................................................... 46
SMART STRETCH .............................................. 53
Speaker ................................................................ 63
Special Modes ..................................................... 49
sRGB ................................................................... 60
Startup image ...................................................... 68
Status ................................................................... 78
STRETCH ............................................................ 53
Supplied accessories ........................................... 14
Target ................................................................... 60
Temperature warning indicator ............................ 83
UNDO button ....................................................... 39
USB cable ............................................................ 25
USB terminal........................................................ 25
VAO ...................................................................... 63
Video System ....................................................... 66
VOLUME buttons ................................................. 35
WIRED R/C JACK................................................ 26
WIRED REMOTE control input terminal ............. 26
Wireless Presentation Function .......................... 25
Zoom knob ........................................................... 28
SHARP CORPORATION
… 104

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sharp xg c45x bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sharp xg c45x in de taal/talen: Engels als bijlage per email.

De handleiding is 9,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info