Handleiding Sharp pg f312x (pagina 3 van 74) (Engels)

215848

Verklein

Vergroot

Pagina terug

1/74

Pagina verder

Introduction Quick Start Setup

Connections

Basic

Operation

Useful

Features

Appendix

OPERATION MANUAL

DATA PROJECTOR

MODEL

PG-F312X

PG-F262X

PG-F212X

IMPORTANT

• For your assistance in reporting the loss

or theft of your Projector, please record

the Model and Serial Number located on

the bottom of the projector and retain this

information.

• Before recycling the packaging, please

ensure that you have checked the con-

tents of the carton thoroughly against the

list of “Supplied accessories” on page 10.

Model No.:

Serial No.:

iii

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat-

ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362

fuse marked

or and of the same rating as above, which is also indicated on the pin

face of the plug, must be used.

Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse

cover fitted.

In the unlikely event of the socket outlet in your home not being compatible with the plug

supplied, cut off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-

ately and disposed of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket

outlet, as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the instructions below:

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : Earth

Blue : Neutral

Brown : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the

coloured markings identifying the terminals in your plug proceed as follows:

• The wire which is coloured green-and-yellow must be connected to the terminal in the

plug which is marked by the letter E or by the safety earth symbol

or coloured green or

green-and-yellow.

• The wire which is coloured blue must be connected to the terminal which is marked with

the letter N or coloured black.

• The wire which is coloured brown must be connected to the terminal which is marked with

the letter L or coloured red.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

The supplied CD-ROM contains operation instructions in English, German, French,

Spanish, Italian, Dutch, Swedish, Portuguese, Chinese and Korean. Carefully read

through the operation instructions before operating the projector.

Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,

Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch und Koreanisch.

Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.

Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand,

français, espagnol, italien, néerlandais, suédois, portugais, chinois et coréen. Veuillez lire

attentivement ces instructions avant de faire fonctionner le projecteur.

Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska,

franska, spanska, italienska, holländska, svenska, portugisiska, kinesiska och koreanska.

Läs noga igenom bruksanvisningen innan projektorn tas i bruk.

El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán,

francés, español, italiano, holandés, sueco, portugués, chino y coreano. Lea

cuidadosamente las instrucciones de operación antes de utilizar el proyector.

Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese,

spagnolo, italiano, olandese, svedese, portoghese, cinese e coreano. Leggere

attentamente le istruzioni per l’uso prima di usare il proiettore.

De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans,

Italiaans, Nederlands, Zweeds, Portugees, Chinees en Koreaans. Lees de handleiding

zorgvuldig door voor u de projector in gebruik neemt.

O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês,

Espanhol, Italiano, Holandês, Sueco, Português, Chinês e Coreano. Leia

cuidadosamente todas as instruções de operação antes de operar o projetor.

Introduction

Before using the projector, please read this operation manual carefully.

There are two important reasons for prompt warranty registration of your new SHARP

Projector, using the REGISTRATION CARD packed with the projector.

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service

and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection,

modification, or recall that SHARP may be required to give under the 1972

Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT

“LIMITED WARRANTY” CLAUSE.

WARNING: High brightness light source. Do not stare into the beam of light, or view

directly. Be especially careful that children do not stare directly into the

beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose

this product to rain or moisture.

WARNING: FCC Regulations state that any unauthorized changes or modifications to

this equipment not expressly approved by the manufacturer could void

the user’s authority to operate this equipment.

The lightning flash with arrowhead sym-

bol, within an equilateral triangle, is in-

tended to alert the user to the presence

of uninsulated “dangerous voltage”

within the product’s enclosure that may

be of sufficient magnitude to constitute

a risk or electric shock to persons.

The exclamation point within a triangle

is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in

the literature accompanying the product.

Introduction

ENGLISH

See bottom of projector.

U.S.A. ONLY

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 52.

This SHARP projector uses a DLP

chip. This very sophisticated panel contains 786,432 pixels

(micromirrors). As with any high technology electronic equipment such as large screen TVs,

video systems and video cameras, there are certain acceptable tolerances that the equipment

must conform to.

This unit has some inactive pixels within acceptable tolerances which may result in inactive dots

on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance

with the operation manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference, in which case the user will be required to correct the

interference at his own expense.

U.S.A. ONLY

Authorized representative responsible for the European Union Community Market

SHARP ELECTRONICS (Europe) GmbH

Sonninstraße 3, D-20097 Hamburg

E.U. ONLY

The enclosed computer cable must be used with the device. The cable is

provided to ensure that the device complies with FCC Class A verification.

U.S.A. ONLY

WARNING:

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

PRODUCT DISPOSAL

This product utilizes tin-lead solder, and lamp containing a small amount

of mercury. Disposal of these materials may be regulated due to

environmental considerations. For disposal or recycling information,

please contact your local authorities, the Electronics Industries Alliance:

www.eiae.org, the lamp recycling organization www.lamprecycle.org,

or Sharp at 1-800-BE-SHARP.

U.S.A. ONLY

Introduction

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Press MENU/HELP.

• The “Picture” menu screen for the se-

lected input mode is displayed.

Example: “Picture” screen menu for

COMPUTER (RGB) input

Press Q or O and select “Picture”

to adjust.

Menu item

Picture Mode

Contrast 0

Bright

Standard

SEL./ADJ. ENTER END

Red

Blue

CLR Temp

BrilliantColor

C.M.S. Setting

C.M.S.

Lamp Setting

Bright

DNR

Off

Reset

Picture SCR - ADJ PRJ - ADJ Help

Adjustment buttons (P/R/O/Q)

MENU/HELP button

ENTER button

Adjustment buttons

(P/R/O/Q)

ENTER button

RETURN button

•Press RETURN to return

to the previous screen

when the menu is

displayed.

MENU/HELP button

Using the Menu Screen

How to Read this Operation Manual

■ The specifications are slightly different, depending on the model. However, you can connect and

operate all models in the same manner.

••

• In this operation manual, the illustration and the screen display are simplified for explanation, and

may differ slightly from the actual display.

Info

........Indicates safeguards for using the projector.

For Future Reference

Buttons used in

this operation

On-screen

display

Button used in

this step

Note

.........Indicates additional information for setting up and operating the

projector.

IndexMaintenance Troubleshooting

P. 6 9P. 4 9

PP. 64 and 65

Contents

Preparing

Introduction

How to Read this Operation Manual .... 3

Contents ............................................... 4

IMPORTANT SAFEGUARDS ............... 6

How to Access the PDF Operation

Manuals .............................................. 9

Accessories ........................................ 10

Part Names and Functions ................. 11

Projector ............................................... 11

Rear View ............................................. 12

Inserting the Batteries .......................... 14

Usable Range ...................................... 15

Quick Start

Quick Start .......................................... 16

Setup and Projection ............................ 16

Setup

Setting up the Projector ...................... 18

Setting up the Projector ....................... 18

Standard Setup (Front Projection) ....... 18

Ceiling-mount Setup ............................ 18

Projection (PRJ) Mode ......................... 19

Screen Size and Projection Distance .. 20

Connections

Connecting the Projector to

Other Equipment .............................. 21

Controlling the Projector by

a Computer ....................................... 24

Connecting the Power Cord ............... 24

Useful Features

Operating with the Remote Control .... 32

Displaying and Setting the

Break Timer........................................ 32

Displaying the Pointer .......................... 32

Using the Spot Function ...................... 32

Switching the Eco+Quiet Mode ........... 32

Auto Sync (Auto Sync Adjustment) ..... 33

Freezing a Moving Image .................... 33

Selecting the Picture Mode .................. 33

Displaying an Enlarged Portion of

an Image ............................................ 33

Using the Remote Control as the

Wireless Computer Mouse ................ 34

Menu Items ......................................... 35

Using the Menu Screen ...................... 38

Menu Selections (Adjustments) ........... 38

Picture Adjustment (“Picture” Menu) ... 40

Selecting the Picture Mode .................. 40

Adjusting the Image ............................. 41

Adjusting the Color Temperature ......... 41

Adjusting the Colors ............................. 41

Progressive ........................................... 42

Reducing Image Noise (DNR) ............. 42

Lamp Setting ........................................ 42

Adjusting the Projector Image

(“SCR - ADJ” Menu) ......................... 43

Setting the Resize Mode ...................... 43

Adjusting the Image Position ............... 43

Keystone Correction ............................ 43

Setting the On-screen Display ............. 43

Closed Caption .................................... 44

Selecting the Background Image ........ 44

Selecting the Setup Guide ................... 44

Reversing/Inverting Projected

Images ............................................... 44

Selecting the On-screen Display

Language ........................................... 44

Adjusting the Projector Function

(“PRJ - ADJ” Menu) .......................... 45

Auto Sync (Auto Sync Adjustment) ..... 45

Auto Power Off Function ...................... 45

Auto Restart Function .......................... 45

STANDBY Mode ................................... 45

Setting the Confirmation Sound

(System Sound) ................................. 45

Speaker Setting .................................... 45

Audio Input ........................................... 46

Selecting the Transmission Speed

(RS-232C) .......................................... 46

Fan Mode Setting ................................. 46

System Lock Function .......................... 46

Checking the Lamp Life Status ........... 47

Keylock Function .................................. 47

Using

Basic Operation

Tu r ning the Projector On/Off .............. 25

Turning the Projector on ....................... 25

Turning the Power off (Putting the

Projector into Standby Mode) ........... 25

Image Projection ................................. 26

About the Setup Guide ........................ 26

Adjusting the Projected Image ............ 26

Correcting Trapezoidal Distortion ........ 28

Switching the Input Mode .................... 29

Adjusting the Volume ........................... 29

Displaying the Black Screen and

Turning off the Sound Temporarily .... 29

Resize Mode ......................................... 30

Introduction

Troubleshooting with the

“Help” Menu ...................................... 48

Utilizing the “Help” Menu Functions .... 48

Reference

Appendix

Maintenance ....................................... 49

Maintenance Indicators ...................... 50

Regarding the Lamp ........................... 52

Lamp ..................................................... 52

Caution Concerning the Lamp ............ 52

Replacing the Lamp ............................. 52

Removing and Installing the

Lamp Unit .......................................... 53

Resetting the Lamp Timer .................... 54

Storing the Projector ........................... 55

How to Use the Storage Case ............. 55

Connecting Pin Assignments ............. 56

RS-232C Specifications and

Commands ....................................... 58

Computer Compatibility Chart ............ 63

Troubleshooting .................................. 64

For SHARP Assistance ...................... 66

Specifications ..................................... 67

Dimensions ......................................... 68

Index ................................................... 69

1. Read Instructions

All the safety and operating instructions should

be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be

retained for future reference.

3. Heed Warnings

All warnings on the product and in the operating

instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be

followed.

5. Cleaning

Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water–for example,

near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a

swimming pool; and the like.

8. Accessories

Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may

fall, causing serious injury to a child or adult, and

serious damage to the product. Use only with a

cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with

the product. Any mounting of the product should

follow the manufacturer’s instructions, and should

use a mounting accessory recommended by the

manufacturer.

9. Transportation

A product and cart

combination should be

moved with care. Quick

stops, excessive force,

and uneven surfaces may

cause the product and cart

combination to overturn.

IMPORTANT SAFEGUARDS

10. Ventilation

Slots and openings in the cabinet are provided

for ventilation to ensure reliable operation of the

product and to protect it from overheating, and

these openings must not be blocked or covered.

The openings should never be blocked by placing

the product on a bed, sofa, rug, or other similar

surface. This product should not be placed in a

built-in installation such as a bookcase or rack

unless proper ventilation is provided or the

manufacturer’s instructions have been adhered

to.

11. Power Sources

This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply to your home, consult your product dealer

or local power company. For products intended

to operate from battery power, or other sources,

refer to the operating instructions.

12. Grounding or Polarization

This product is provided with one of the following

types of plugs. If the plug should fail to fit into the

power outlet, please contact your electrician.

Do not defeat the safety purpose of the plug.

a. Two-wire type (mains) plug.

b. Three-wire grounding type (mains) plug with

a grounding terminal.

This plug will only fit into a grounding type

power outlet.

13. Power-Cord Protection

Power-supply cords should be routed so that they

are not likely to be walked on or pinched by items

placed upon or against them, paying particular

attention to cords at plugs, convenience

receptacles, and the point where they exit from

the product.

14. Lightning

For added protection for this product during a

lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from

the wall outlet and disconnect the cable system.

This will prevent damage to the product due to

lightning and power-line surges.

CAUTION: Please read all of these instructions before you operate this product

and save these instructions for later use.

Electrical energy can perform many useful functions. This product has been engineered

and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN

POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the

safeguards incorporated in this product, observe the following basic rules for its installation,

use and servicing.

Introduction

15. Overloading

Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can

result in a risk of fire or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product

through openings as they may touch dangerous

voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any

kind on the product.

17. Servicing

Do not attempt to service this product yourself as

opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

18. Damage Requiring Service

Unplug this product from the wall outlet and refer

servicing to qualified service personnel under the

following conditions:

a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects have fallen

into the product.

c. If the product has been exposed to rain or

water.

d. If the product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the

operating instructions, as an improper

adjustment of other controls may result in

damage and will often require extensive work

by a qualified technician to restore the product

to normal operation.

e. If the product has been dropped or damaged

in any way.

f. When the product exhibits a distinct change

in performance, this indicates a need for

service.

• DLP

and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor

is a trademark of Texas Instruments.

• Microsoft

and Windows

are registered trademarks of Microsoft Corporation in the United

States and/or other countries.

• PC/AT is a registered trademark of International Business Machines Corporation in the

United States.

• Adobe

Reader

is a trademark of Adobe Systems Incorporated.

• Macintosh

is a registered trademark of Apple Computer, Inc. in the United States and/or

other countries.

• All other company or product names are trademarks or registered trademarks of their

respective companies.

• Some IC chips in this product include confidential and/or trade secret property belonging

to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,

reverse engineer, reverse assemble or discompile the contents thereof.

19. Replacement Parts

When replacement parts are required, be sure

the service technician has used replacement

parts specified by the manufacturer or have the

same characteristics as the original part.

Unauthorized substitutions may result in fire,

electric shock, or other hazards.

20. Safety Check

Upon completion of any service or repairs to this

product, ask the service technician to perform

safety checks to determine that the product is in

proper operating condition.

21. Wall or Ceiling Mounting

This product should be mounted to a wall or

ceiling only as recommended by the

manufacturer.

22. Heat

This product should be situated away from heat

sources such as radiators, heat registers, stoves,

or other products (including amplifiers) that

produce heat.

Observe the following safeguards when setting up your

projector.

Caution concerning the lamp unit

■ Potential hazard of glass par-

ticles if lamp ruptures. In case

of lamp rupture, contact your

nearest Sharp Authorized

Projector Dealer or Service

Center for replacement.

See “Replacing the Lamp” on

page 52.

Caution concerning the setup of the

projector

■ For minimal servicing and to maintain high

image quality, SHARP recommends that this

projector be installed in an area free from

humidity, dust and cigarette smoke. When the

projector is subjected to these environments,

the vents and lens must be cleaned more of-

ten. As long as the projector is regularly

cleaned, use in these environments will not

reduce the overall operation life of the unit.

Internal cleaning should only be performed

by a Sharp Authorized Projector Dealer or

Service Center.

Do not set up the projector in places

exposed to direct sunlight or bright light.

■ Position the screen so that it is not in direct

sunlight or room light. Light falling directly on

the screen washes out the colors, making

viewing difficult. Close the curtains and dim

the lights when setting up the screen in a

sunny or bright room.

Caution regarding placing of the projector

■ Place the projector on a level site within the

adjustment range (9 degrees) of the adjust-

ment foot.

When using the projector in high-altitude

areas such as mountains (at altitudes of

approximately 1,500 meters (4,900 feet)

or more)

■ When you use the projector in high-altitude

areas with thin air, set “Fan Mode” to “High”.

Neglecting this can affect the longevity of the

optical system.

Warning about placing the projector in

a high position

■ When placing the projector in a high position,

make certain it is carefully secure to avoid

personal injury caused by the projector fall-

ing down.

Do not subject the projector to hard

impact and/or vibration.

■ Protect the lens so as not to hit or damage

the surface of the lens.

Rest your eyes occasionally.

■ Continuously watching the screen for long

hours will cause eye strain. Take regular

breaks to rest your eyes.

Avoid locations with extremes of

temperature.

■ The operating temperature of the projector is

from 41°F to 95°F (+5°C to +35°C).

■ The storage temperature of the projector is

from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake

vents.

■ Allow at least 11

/16 inches (30 cm) of space

between the exhaust vent and the nearest

wall or obstruction.

■ Ensure that the intake vent and the exhaust

vent are not obstructed.

■ If the cooling fan becomes obstructed, a pro-

tection circuit will automatically put the pro-

jector into standby mode to prevent overheat

damage. This does not indicate a malfunc-

tion. (See pages 50 and 51.) Remove the pro-

jector power cord from the wall outlet and wait

at least 10 minutes. Place the projector where

the intake and exhaust vents are not blocked,

plug the power cord back in and turn on the

projector. This will return the projector to the

normal operating condition.

■ After the projector is purchased, a faint smell

from the vent may appear when the power is

first turned on. This is normal and is not a

malfunction. It will disappear after the projec-

tor is used for a while.

Accessories

Remote control

Two R-6 batteries

(“AA” size, UM/SUM-3,

HP-7 or similar)

Power cord*

RGB cable

(10' (3.0 m))

Optional accessories

■ Lamp unit

■ Ceiling-mount adaptor

■ Ceiling-mount unit

■ Remote receiver

■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m))

AN-F212LP

AN-60KT

AN-XRCM30 (for U.S.A. only)

AN-TK201 <for AN-60KT>

AN-TK202 <for AN-60KT>

AN-EP101B <for AN-XRCM30>

(for U.S.A. only)

AN-MR2

AN-C3CP2

Supplied accessories

For U.S. and

Canada, etc.

(6' (1.8 m))

For Europe,

except U.K.

(6' (1.8 m))

For U.K. and

Singapore

(6' (1.8 m))

For Australia, New

Zealand and Oceania

(6' (1.8 m))

(1) (2) (3) (4)

* Use the power cord that corresponds to the wall outlet in your country.

• Operation manual (this manual <TINS-D519WJZZ> and CD-ROM <UDSKAA098WJZZ>)

Note

• Some of the optional accessories may not be available depending on the region. Please check with

your nearest Sharp Authorized Projector Dealer or Service Center.

Lens cap (attached)

DIN-D-sub RS-232C adaptor

" (15 cm))

Storage case

Note

• Codes in “< >” are Replacement parts codes.

Introduction

Numbers in Z refer to the main pages in this operation manual where the topic

is explained.

Projector

Part Names and Functions

25, 50

37, 46

25, 50

Top View

STANDBY/ON

button

For turning the

power on and

putting the

projector into

standby mode.

Lamp indicator

Temperature warning

indicator

Adjustment buttons

(P/R/O/Q)

For selecting menu items.

VOL (Volume) buttons

(–O/Q+)

For adjusting the

speaker sound level.

ENTER button

For setting

items selected

or adjusted on

the menu.

MENU/HELP button

For displaying

adjustment and

setting screens, and

help screen.

Focus ring

For adjusting

the focus.

INPUT buttons (P/R)

For switching input mode.

Remote control

sensor

HEIGHT

ADJUST lever

KEYSTONE

button

For entering the

Keystone

Correction mode.

Intake vent

Power

indicator

Zoom ring

For enlarging/

reducing the picture.

Push both sides of the lens cap

to attach or remove.

ECO+QUIET button

For lowering the noise

of the cooling fan and

extending the lamp life.

Front View

Exhaust vent

Speaker

Numbers in Z refer to the main pages in this operation manual where the topic

is explained.

Rear View

Using the Kensington Lock

• This projector has a Kensington Security Standard connector for use with a Kensington

MicroSaver Security System. Refer to the information that came with the system for

instructions on how to use it to secure the projector.

Part Names and Functions (Continued)

Terminals

AUDIO 2 input

terminal

S-VIDEO input terminal

Ter minal for connecting

video equipment with an

S-video terminal.

VIDEO input

terminal

Ter minal for

connecting video

equipment.

Rear

adjustment

foot

Kensington Security

Standard connector

AC socket

Connect the supplied

power cord.

AUDIO OUT

terminal

Audio output terminal of

equipment connected to the

audio input terminal.

AUDIO 1 input terminal

DVI-I input

terminal

Ter minal for

DVI digital,

computer RGB

and component

signals.

MONITOR OUT

terminal

(Output terminal for computer RGB,

component and DVI analog signals. Shared

for COMPUTER/COMPONENT and DVI-I)

Ter minal for connecting a monitor.

RS-232C terminal

Ter minal for

controlling the

projector using a

computer.

COMPUTER/

COMPONENT input

terminal

Ter minal for computer RGB

and component signals.

USB terminal

Terminal connecting

with the USB

terminal on the

computer for using

the supplied remote

control as the

computer mouse.

Introduction

STANDBY button

For putting the projector

into the standby mode.

BREAK TIMER button

For displaying the

break time.

COMPUTER, DVI,

S-VIDEO, VIDEO buttons

For switching to the

respective input modes.

PAGE UP/PAGE

DOWN buttons

Same as the [Page Down] and

[Page Up] keys on a computer

keyboard, when with the USB

connection (using a USB cable

or the optional remote

receiver).

POINTER button

For displaying the

pointer.

MOUSE/Adjustment

buttons (P/R/O/Q)

• For moving the

computer cursor when with the USB

connection (using a USB cable or the

optional remote receiver).

• For selecting and adjusting menu

items.

L-CLICK/EFFECT

button

• For the Left click

when with the USB connection

(using a USB cable or the optional

remote receiver).

• For changing the pointer or spot

area.

KEYSTONE button

For entering the

Keystone Correction mode.

AUTO SYNC button

For automatically

adjusting images when

connected to a computer.

ECO+QUIET button

For lowering the noise

of the cooling fan and

extending the lamp life.

AV MUTE button

For temporarily

displaying a black

screen and turning

off the sound.

FREEZE button

For freezing images.

VOL +/– (Volume)

buttons

For adjusting the

speaker sound level.

ON button

For turning the power

on.

SPOT button

For displaying the

spotlight.

R-CLICK/RETURN

button

• For the Right click

when with the USB

connection (using a

USB cable or the

optional remote

receiver).

• For returning to the

previous menu screen

during menu

operations.

ENTER button

For setting items

selected or adjusted

on the menu.

MENU/HELP button

For displaying

adjustment and

setting screens, and

help screen.

PICTURE MODE

button

For selecting the

appropriate picture.

RESIZE button

For switching the

picture size

(NORMAL, BORDER,

etc.).

MAGNIFY buttons

For enlarging/reducing

part of the image.

• Danger of explosion if battery is incorrectly replaced.

Replace only with alkaline or manganese batteries.

• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery

compartment.

• Batteries of different types have different properties, therefore do not mix batteries of different types.

• Do not mix new and old batteries.

This may shorten the life of new batteries or may cause old batteries to leak.

• Remove the batteries from the remote control once they have run out, as leaving them in can cause them

to leak.

Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove

them using a cloth.

• The batteries included with this projector may run down in a short period, depending on how they are kept.

Be sure to replace them as soon as possible with new batteries.

• Remove the batteries from the remote control if you will not be using the remote control for a long time.

• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

Incorrect use of the batteries may cause them to leak or explode. Please

follow the precautions below.

Part Names and Functions (Continued)

Inserting the Batteries

Insert the lower tab of the cover into the opening,

and lower the cover until it clicks in place.

Insert the batteries.

• Insert the batteries making sure the polarities correctly match

the m and n marks inside the battery compartment.

Pull down the tab on the cover and remove the cover

towards the direction of the arrow.

Caution

Introduction

Usable Range

The remote control can be used to control the

projector within the ranges shown in the

illustration.

Note

• The signal from the remote control can be re-

flected off a screen for easy operation. How-

ever, the effective distance of the signal may

differ depending on the screen material.

When using the remote control

• Ensure that you do not drop it or expose it to

moisture or high temperature.

• The remote control may malfunction under a

fluorescent lamp. In this case, move the pro-

jector away from the fluorescent lamp.

Remote control sensor

Remote control

signal transmitters

Remote control

23n (7 m)

30°

Quick Start

This section shows the basic operation (projector connecting with the computer). For details, see

the page described below for each step.

Setup and Projection

In this section, connection of the projector and the computer is explained using one example.

When connecting equipment other than a computer, see

pages 22 and 23.

3. Remove the lens cap and turn the projector on

2. Connect the projector to the computer and plug the power cord

into the AC socket of the projector

On the projector On the remote control

KEYSTONE button

INPUT buttons

STANDBY/ON

button

HEIGHT

ADJUST lever

Focus ring

STANDBY button

_PP. 21, 24

_P. 25

ENTER button

KEYSTONE

button

ON button

COMPUTER button

1. Place the projector facing a wall or a screen

_P. 18

Adjustment buttons

(P/R/O/Q)

Adjustment buttons

(P/R/O/Q)

Zoom ring

Quick Start

4. Adjust the projected image with the Setup Guide

_PP. 26, 27

1 After the projector turns on, the Setup Guide appears.

(When “Setup Guide” is set to “On”. See page 44.)

2 Follow the steps in the Setup Guide and adjust the focus, picture size, and height (angle).

3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup

Guide.

Correcting trapezoidal distortion using Keystone Correction.

5. Correct trapezoidal distortion

8. Turn the power off

Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the

button again while the confirmation message is displayed to put the projector into standby mode.

On-screen display

On the

projector

On the remote

control

_P. 25

On the projector

On the remote control

Shrinks

upper side.

Shrinks

lower side.

_P. 28

Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote control.

6. Select the INPUT mode

• When you press INPUT on the projector, the INPUT list appears.

Press '/" to switch the INPUT mode.

On the

projector

On the remote

control

INPUT list

_P. 29

INPUT

COMPUTER

DVI-D Computer

DVI-D Video

On-screen display (RGB)

RGB

1024 × 768

COMPUTER

7. Turn the computer on

Ceiling-mount Setup

■ It is recommended that you use the optional

Sharp ceiling-mount adaptor and unit for this

installation. Before mounting the projector,

contact your nearest Sharp Authorized

Projector Dealer or Service Center to obtain

the recommended ceiling-mount adaptor and

unit (sold separately).

Setting up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector’s feet

flat and level. Doing so will eliminate the need for Keystone correction and provide the best image

quality. (See page 28.)

Standard Setup (Front Projection)

■ Place the projector at the required distance from the screen according

to the desired picture size. (See page 20.)

Example of standard setup

Screen

Lens center

• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.

Note

Side View

Setup

300"

200"

100"

80"

60"

36'10

(11.2 m)

24'7

"–

28'4

(7.5 m

–

8.6 m)

12'3

"–

14'2

(3.7 m

–

4.3 m)

9'10

"–

11'4

(3.0 m

–

3.5 m)

7'4

"–

8'6

(2.2 m – 2.6 m)

240"×180"

160"

120"

80"

60"

64"

48"

36"

Projection (PRJ) Mode

The projector can use any of the 4 projection modes shown in the diagram below. Select the mode

most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu.

See page 44.)

■ Ta ble mounted, front projection

[Menu item ➞ “Front”]

■ Ceiling mounted, front projection

[Menu item ➞ “Ceiling + Front”]

■ Ta ble mounted, rear projection

(with a translucent screen)

[Menu item ➞ “Rear”]

■ Ceiling mounted, rear projection

(with a translucent screen)

[Menu item ➞ “Ceiling + Rear”]

Indication of the Projection Image Size and Projection Distance

Picture Size

Projection

Distance

Example: NORMAL Mode (4:3)

Setting up the Projector (Continued)

300Љ (762 cm)

250Љ (635 cm)

200Љ (508 cm)

150Љ (381 cm)

120Љ (305 cm)

100Љ (254 cm)

80Љ (203 cm)

70Љ (178 cm)

60Љ (152 cm)

40Љ (102 cm)

610 cm (240Љ)

508 cm (200Љ)

406 cm (160Љ)

305 cm (120Љ)

244 cm (96Љ)

203 cm (80Љ)

163 cm (64Љ)

142 cm (56Љ)

122 cm (48Љ)

81 cm (32Љ)

19 cm

16 cm

13 cm

10 cm

8 cm

6 cm

5 cm

4 cm

3 cm

Љ)

457 cm (180Љ)

381 cm (150Љ)

305 cm (120Љ)

229 cm (90Љ)

183 cm (72Љ)

152 cm (60Љ)

122 cm (48Љ)

107 cm (42Љ)

91 cm (36Љ)

61 cm (24Љ)

11.2 m (36Ј 10Љ)

9.4 m (30Ј 9Љ)

7.5 m (24Ј 7Љ)

5.6 m (18Ј 5Љ)

4.5 m (14Ј 9Љ)

3.7 m (12Ј 3Љ)

3.0 m (9Ј 10Љ)

2.6 m (8Ј 7Љ)

2.2 m (7Ј 4Љ)

1.5 m (4Ј 11Љ)

—

10.8 m (35Ј 5Љ)

8.6 m (28Ј 4Љ)

6.5 m (21Ј 3Љ)

5.2 m (17Ј 0Љ)

4.3 m (14Ј 2Љ)

3.5 m (11Ј 4Љ)

3.0 m (9Ј 11Љ)

2.6 m (8Ј 6Љ)

1.7 m (5Ј 8Љ)

The formula for picture size and projection distance

[m/cm]

L1 (m) = 0.0408

L2 (m) = 0.0471

H (cm) = 0.27727

S (cm) = ±0.20754

Screen Size and Projection Distance

NORMAL Mode (4:3)

• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the

bottom of the image [H]”.

• Allow a margin of error in the values in the diagrams above.

Picture (Screen) size

The formula for picture size and projection distance

[m/cm]

L1 (m) = 0.03745

L2 (m) = 0.04323

H (cm) = 0.064

: Picture size (diag.) (in/cm)

L: Projection distance (m/ft)

L1: Minimum projection distance (m/ft)

L2: Maximum projection distance (m/ft)

H: Distance from the lens center to the bottom of the image (cm/in)

: Picture size (diag.) (in/cm)

L: Projection distance (m/ft)

L1: Minimum projection distance (m/ft)

L2: Maximum projection distance (m/ft)

H: Distance from the lens center to the bottom of the image (cm/in)

S: Adjustable range of image position (cm/in) See page 43.

Projection distance [L]

Diag. [

] Width Height

Minimum [L1] Maximum [L2]

250Љ (635 cm)

200Љ (508 cm)

150Љ (381 cm)

120Љ (305 cm)

100Љ (254 cm)

80Љ (203 cm)

60Љ (152 cm)

40Љ (102 cm)

553 cm (218Љ)

443 cm (174Љ)

332 cm (131Љ)

266 cm (105Љ)

221 cm (87Љ)

177 cm (70Љ)

133 cm (52Љ)

89 cm (35Љ)

69 cm

55 cm

42 cm

33 cm

28 cm

22 cm

17 cm

11 cm

(27

/64Љ)

(21

/64Љ)

(16

/8Љ)

(13

/32Љ)

(10

/64Љ)

ע52 cm

ע42 cm

ע31 cm

ע25 cm

ע21 cm

ע17 cm

ע12 cm

ע 8 cm

(ע20

/64Љ)

(ע16

/32Љ)

(ע12

/4Љ)

(ע9

/16Љ)

(ע8

/64Љ)

(ע6

/32Љ)

(ע4

/32Љ)

(ע3

/64Љ)

311 cm (123Љ)

249 cm (98Љ)

187 cm (74Љ)

149 cm (59Љ)

125 cm (49Љ)

100 cm (39Љ)

75 cm (29Љ)

50 cm (20Љ)

10.2 m (33Ј 6Љ)

8.2 m (26Ј 9Љ)

6.1 m (20Ј 1Љ)

4.9 m (16Ј 1Љ)

4.1 m (13Ј 5Љ)

3.3 m (10Ј 9Љ)

2.4 m (8Ј 0Љ)

1.6 m (5Ј 4Љ)

11.8 m (38Ј 8Љ)

9.4 m (30Ј 11Љ)

7.1 m (23Ј 2Љ)

5.7 m (18Ј 7Љ)

4.7 m (15Ј 5Љ)

3.8 m (12Ј 4Љ)

2.8 m (9Ј 3Љ)

1.9 m (6Ј 2Љ)

Note

Distance from the lens center

to the bottom of the image [H]

Picture (Screen) size

Projection distance [L]

Diag. [

] Width Height

Minimum [L1] Maximum [L2]

Distance from the lens center to

the bottom of the image [H]

Adjustable range of

image position [S]

STRETCH Mode (16:9)

[Feet/inches]

L1 (ft) = 0.03745

/ 0.3048

L2 (ft) = 0.04323

/ 0.3048

H (in) = 0.064

/ 2.54

[Feet/inches]

L1 (ft) = 0.0408

/ 0.3048

L2 (ft) = 0.0471

/ 0.3048

H (in) = 0.27727

/ 2.54

S (in) = ±0.20754

/ 2.54

Connections

Before connecting, ensure that the power cord of the projector is unplugged from the AC

outlet and turn off the equipment to be connected. After making all connections, turn on the

projector and then the other pieces of equipment. When connecting a computer, ensure that

it is the last equipment to be turned on after all the connections are made.

IMPORTANT:

Ensure that the appropriate input mode has been selected on the projector before

you turn on the connected equipment.

•

For more details of connection and cables, refer to the operation manual of the connecting equipment.

•You may need other cables or connectors not listed below.

Connecting the Projector to Other Equipment

COMPUTER/

COMPONENT

DVI-I

Equipment

Computer

DVI digital

output

terminal

Cable

DVI Digital cable (commercially available)

mini D-sub 15 pin to DVI cable

(commercially available)

Terminal on

connected equipment

Terminal on the

projector

RGB

output

terminal

RGB

output

terminal

RGB cable (supplied)

• See page 63 “Computer Compatibility Chart” for a list of computer signals compatible with the projec-

tor. Use with computer signals other than those listed may cause some of the functions to not work.

•A Macintosh adaptor may be required for use with some Macintosh computers. Contact your near-

est Macintosh Dealer.

• Depending on the computer you are using, an image may not be projected unless the

computer’s external output port is switched on (e.g. Press “Fn” and “F5” keys simultaneously

when using a SHARP notebook computer). Refer to the specific instructions in your computer's

operation manual to enable your computer’s external output port.

Note

Terminals on the Projector

Connecting the Projector to Other Equipment (Continued)

S-VIDEO

VIDEO

COMPUTER/

COMPONENT

Equipment

Video equipment

Camera/Video game

Cable

S-video cable (commercially available)

Video cable (commercially available)

Cables for a camera or a video game

Cables for a camera or a video game/3 RCA

to mini D-sub 15 pin cable (optional,

AN-C3CP2)

Terminal on

connected equipment

Terminal on the

projector

S-video

output

terminal

Video

output

terminal

S-video

output

terminal

Video

output

terminal

Component

video

output

terminal

RCA adaptor plug

(commercially available)

S-VIDEO

VIDEO

3 RCA to mini D-sub 15 pin cable

(optional, AN-C3CP2)

COMPUTER/

COMPONENT

Component

video

output

terminal

HDMI to DVI cable

(commercially available)

DVI-I

HDMI

output

terminal

DVI digital

output

terminal

DVI Digital cable (commercially available)

• While the projector is connected to video equipment that has an HDMI output terminal, only the

video signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)

• Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission

may not work property. (The HDMI specification does not support all connections to video equipment

that has HDMI digital output terminal using HDMI to DVI digital cable.)

• For details on compatibility for connection, see support information on DVI connection provided by

the video equipment manufacturer.

• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a

commercially available cable that fits in the projector terminal you want to connect.

• The projector does not support RGBC signals via the Euro-scart.

Note

Connections

Note

• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm

stereo audio cable.

•You can select “Audio 1” or “Audio 2” for “Audio Input” in the “PRJ-ADJ” menu. (See page 46.)

• RGB signals and Component signals can be output to the monitor.

Equipment Cable

Terminal on

connected equipment

Terminal on the

projector

Audio

output

terminal

Monitor

Amplifier

MONITOR OUT

AUDIO OUT

RGB

input

terminal

RGB cable (supplied or commercially

available)

Audio equipment

ø3.5 mm stereo or mono audio cable

(commercially available or available

as Sharp service part QCNWGA038WJPZ)

ø3.5 mm

audio output

terminal

ø3.5 mm

audio input

terminal

RCA audio

output

terminal

RCA audio

input

terminal

ø3.5 mm stereo or mono audio cable

(commercially available or available

as Sharp service part QCNWGA038WJPZ)

ø3.5 mm stereo minijack to RCA audio cable

(commercially available)

RCA audio cable (commercially available)

Cables for a camera or a video game

AUDIO 2

AUDIO 1

Connecting the Power Cord

Plug the supplied power cord into the

AC socket on the rear of the projector.

Then plug into AC outlet.

AC socket

To AC outlet

Power cord

(supplied)

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-

232C adaptor and an RS-232C serial control cable (cross type, commercially available), the computer

can be used to control the projector and check the status of the projector. See page 58 for details.

When connecting to a computer using an RS-232C serial control cable and a DIN-

D-sub RS-232C adaptor

To RS-232C terminal

DIN-D-sub RS-232C

adaptor (supplied)

RS-232C serial control cable (cross type, commercially available)

Note

• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the

operation manual of the computer for details.

• See page 57 for connection of an RS-232C serial control cable.

Info

• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This

may damage your computer or projector.

• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.

This may damage your computer.

Computer

To RS-232C terminal

Basic

Operation

Turning the Projector On/Off

On-screen display (confirmation message)

• When “Auto Restart” is set to “On”:

If the power cord is unplugged from the outlet

or the breaker switch is turned off when the

projector is on, then the projector automatically

turns on when the power cord is plugged into

the AC outlet or the breaker switch is turned

on. (See page 45.)

• English is the factory default language. If you

want to change the on-screen display to an-

other language, change the language accord-

ing to the procedure on page 44.

Info

Tur ning the Projector on

Note that the connections to external equip-

ment and power outlet should be done be-

fore performing the operations written be-

low. (See pages 21 to 24.)

Remove the lens cap and press

STANDBY/ON on the projector or ON

on the remote control.

• The power indicator illuminates green.

• After the lamp indicator illuminates, the projec-

tor is ready to start operation.

Note

• About the Lamp Indicator

The lamp indicator illuminates to indicate the

status of the lamp.

Green: The lamp is on.

Blinking in green: The lamp is warming up.

Red: The lamp is shut down abnormally

or the lamp should be replaced.

• When switching on the projector, a slight flicker-

ing of the image may be experienced within the

first minute after the lamp has been illuminated.

This is normal operation as the lamp’s control

circuitry is stabilising the lamp output character-

istics. It should not be regarded as faulty

operation.

• If the projector is put into standby mode and

immediately turned on again, the lamp may take

some time to start projection.

•

When System Lock is set, the keycode input box

appears. To cancel the keycode setting, input the

keycode that you have already set. See page 46

for details.

Turning the Power off (Putting

the Projector into Standby Mode)

Press STANDBY/ON on the projector or

STANDBY on the remote control, then

press that button again while the confir-

mation message is displayed, to put the

projector into standby mode.

• The projector cannot be turned on while cool-

ing.

STANDBY

button

ON button

• Direct Power Off function:

You can unplug the power cord from the AC out-

let even if the cooling fan is still running.

Info

STANDBY/ON button

Lamp indicator

Power indicator

About the Setup Guide

After turning on the projector, the Setup

Guide screen appears to assist you with

projector setup.

Guidance items

1 FOCUS

2 HEIGHT ADJUST

3 ZOOM

Press ENTER to exit the Setup Guide

screen.

Image Projection

Setup Guide screen

• The Setup Guide screen automatically high-

lights the items in the following order:

1 FOCUS

3 ZOOM4 ENTER

2 HEIGHT ADJUST

However, you can adjust the focus, height

(angle), or zoom regardless of the highlighted

item.

• If you do not want to display the Setup Guide

for the next time, set “Menu” - “SCR - ADJ” -

“Setup Guide” to “Off”. (See page 44.)

Note

Adjusting the Projected Image

1 Adjusting the Focus

You can adjust the focus with the focus

ring on the projector.

Rotate the focus ring to adjust the fo-

cus while watching the projected image.

2 Adjusting the Picture Size

You can adjust the picture size using

the zoom ring on the projector.

Rotate the zoom ring to enlarge or

shrink the picture size.

STANDBY/ON

button

ENTER button

Focus ring

Zoom ring

Basic

Operation

3 Adjusting the Height

The height of the projector can be ad-

justed using the adjustment feet at the

front and rear of the projector.

When the screen is above the projec-

tor, the projection image can be made

higher by adjusting the projector.

• Do not apply too much pressure on the pro-

jector when the front adjustment foot comes

out.

• When lowering the projector, be careful not to

get your fingers caught in the area between

the adjustment foot and the projector.

•

Hold the projector firmly while lifting or carrying.

• Do not hold by the lens area.

Use the rear adjustment foot to

make the projector level.

• The projector is adjustable ±2 degrees

from the standard position.

Remove your hands from the

HEIGHT ADJUST lever of the pro-

jector after its height has been

finely adjusted.

• The angle of projection is adjustable up

to 9 degrees from the surface on which

the projector is placed.

Lift the projector to adjust its

height while lifting the HEIGHT

ADJUST lever.

Info

• When adjusting the height of the projector,

trapezoidal distortion occurs. Follow the pro-

cedures in Keystone Correction to correct the

distortion. (See pages 28 and 43.)

Note

Rear adjustment foot

HEIGHT

ADJUST lever

Make small

adjustments.

0KEYSTONE

ADJUST END

Correcting Trapezoidal

Distortion

When the image is projected either from

the top or from the bottom towards the

screen at an angle, the image becomes

distorted trapezoidally. The function for

correcting trapezoidal distortion is

called Keystone Correction.

• The Keystone Correction can be adjusted up

to an angle of approximately ±40 degrees and

the screen can also be set up to an angle of

approximately ±40 degrees (when the resize

mode is set to “NORMAL” (see page 30)).

Note

Press KEYSTONE.

• The on-screen display of the Keystone

Correction mode will disappear.

•You can also use KEYSTONE on the pro-

jector.

Press P/Q or O/R to adjust the

Keystone Correction.

•You can also adjust the Keystone Cor-

rection using the adjustment buttons on

the projector.

Press KEYSTONE to enter the

Keystone Correction mode.

•You can also display the on-screen dis-

play of the Keystone Correction mode

with KEYSTONE on the projector.

•To return to the default setting, press RETURN

while the on-screen display of the Keystone

Correction mode is on the screen.

Note

On-screen display

(Keystone Correction mode)

Shrinks upper side.

(Move the slide bar in the + direction.)

Shrinks lower side.

(Move the slide bar in the - direction.)

• While adjusting the image using Keystone

Correction, straight lines and the edges of the

image may appear jagged.

Info

KEYSTONE button

Adjustment buttons

(P/R/O/Q)

RETURN button

Image Projection (Continued)

Basic

Operation

Displaying the Black Screen

and Turning off the Sound

Temporarily

Adjusting the Volume

Switching the Input Mode

Press COMPUTER, DVI, S-VIDEO or

VIDEO on the remote control to select

the input mode.

• When you press INPUT on the projector or DVI

on the remote control, the INPUT list appears.

Press P/R to switch the INPUT mode.

Select the appropriate input mode for

the connected equipment.

Press VOL +/– on the remote control or

–O/Q+ on the projector to adjust the vol-

ume.

•Pressing VOL–/–O will lower the volume.

•Pressing VOL+/Q+ will raise the volume.

• When the projector is connected to external

equipment, the volume level of the external equip-

ment changes in accordance with the volume

level of the projector. Set the projector’s volume

to the lowest level when turning the projector on/

off or when changing the input signal.

• When you do not want to output the sound from

the projector’s speaker while the projector is con-

nected to external equipment, set “Speaker” in

“PRJ-ADJ” menu to “Off”. (See page 45.)

Press AV MUTE on the remote control

to temporarily display a black screen

and turn off the sound.

•Pressing AV MUTE again will turn the pro-

jected image back on.

On-screen display

Note

On-screen display

VOL +/– (Volume)

buttons

COMPUTER, DVI,

S-VIDEO, VIDEO

buttons

AV MUTE button

Basic

Operation

VIDEO

VIDEO/DTV

4:3 aspect ratio

Squeeze

Letter box

16:9 aspect ratio

(4:3 aspect ratio in 16:9)

For 4:3 screen For 16:9 screen

Input signal

Image type NORMALVideo/DTV

480I, 480P,

576I, 576P,

NTSC, PAL,

SECAM

720P, 1035I,

1080I, 1080P

540P

: Cutout area on which images cannot be projected

: Area on which the image is not included in the original signals

The Image Shift function can be used for these images.

Same as NORMAL mode.

BORDER STRETCH

AREA ZOOM

V-STRETCH

About Copyrights

• When using the RESIZE function to select an image size with a different aspect ratio to

a TV program or video image, the image will look different from its original appearance.

Keep this in mind while choosing an image size.

• The use of the Resize or Keystone Correction function to compress or stretch the image

for commercial purposes/public displays in a café, hotel, etc. may be an infringement of

Useful

Features

Auto Sync

(Auto Sync Adjustment)

Freezing a Moving Image

• When the optimum image cannot be achieved

with Auto Sync adjustment, use the help menu

for manual adjustments. (See page 48.)

Auto Sync function works when detect-

ing input signal after the projector turns

on.

Press AUTO SYNC to manually adjust

with Auto Sync function.

Press FREEZE.

• The projected image is frozen.

Press FREEZE again to return to

the moving image from the cur-

rently connected device.

Note

Selecting the Picture Mode

Press PICTURE MODE.

• When pressing PICTURE MODE, the picture

mode changes in the following order:

STANDARD PRESENTATION MOVIE GAME sRGB

You can select the appropriate picture

mode for the projected image, such as

movie or video game.

• See page 40 for details on the picture mode.

Note

* “sRGB” is displayed only when RGB signal is

input.

Displaying an Enlarged

Portion of an Image

Graphs, tables and other portions of

projected images can be enlarged. This

is helpful when providing more detailed

explanations.

Press MAGNIFY on the remote

control.

• Enlarges the image.

•Pressing or MAGNIFY enlarges

or reduces the projected image.

Note

1 2 3 4

Press

Press .

•You can change the location of the en-

larged image using P, R, O and Q.

Press RETURN on the remote con-

trol to cancel the operation.

• The magnification then returns to × 1.

Note

• The selectable magnifications differ

depending on the input signal.

• In the following cases, the image will

return to the normal size (×1).

- When switching the INPUT mode.

- When RETURN has been pressed.

- When the input signal is changed.

- When the input signal resolution and

refresh rate (vertical frequency)

change.

- When the Resize mode is changed.

- When the Picture mode is changed.

- When the Progressive mode is changed.

Using the Remote Control as the Wireless Computer Mouse

When connecting the projector and the computer with a USB cable, you can use

the remote control as the computer mouse.

If the computer is placed too far away from the projector to be connected via the

USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate

the projector with the remote control. For details, see the operation manual of

the receiver.

Connecting with a USB cable

emote receiver

(optional, AN-MR2)

To USB terminal

USB cable

(commercially available or available as

Sharp service part QCNWGA014WJPZ)

To USB terminal

Computer

MOUSE/Adjustment

buttons ('/"/\/|)

R-CLICK button

L-CLICK button

PAGE UP/

PAGE DOWN buttons

The mouse pointer can be oper-

ated in the following way after it

is connected.

■ When moving the cursor

Press MOUSE/Adjustment buttons (P/R/O/Q).

■ When left-clicking

Press L-CLICK.

■ When right-clicking

Press R-CLICK.

■

When your computer supports only a

one-click mouse (such as Macintosh)

Press L-CLICK or R-CLICK.

L-CLICK and R-CLICK have common function.

■ When using [Page Up] or [Page Down]

• This function only works with the Microsoft

Windows

OS and Mac OS

. However, this function

does not work with the following operation systems that do not support USB.

• Versions earlier than Windows

NT4.0

• Versions earlier than Mac OS

8.5

•You cannot use this function when displaying the menu screen.

• Confirm that the computer recognizes the USB connection.

Note

Same as the [Page Up] and [Page Down] keys on a computer keyboard.

Press PAGE UP or PAGE DOWN.

Operating with the Remote Control (Continued)

Useful

Features

The following shows the items that can be set in the projector.

Menu Items

Picture Mode

Contrast 0

Bright

Color

Tint

0Sharp

Standard

SEL./ADJ. ENTER END

Red

Blue

Picture SCR - ADJ PRJ - ADJ Help

Picture Mode

CLR Temp

BrilliantColor

C.M.S. Setting

C.M.S.

Standard

SEL./ADJ. ENTER END

Progressive

Lamp Setting

3D Progressive

Bright

DNR

Off

Reset

Picture SCR - ADJ PRJ - ADJ Help

PAGE 2

Main menu Sub menu

Picture

Page 40 Page 40

Page 41

Page 42

+30-30

Contrast

+30-30

1-1

+30-30

Tint

Color

Sharp

Bright

Progressive

Lamp Setting

Reset

2D Progressive

3D Progressive

Film Mode

CLR Temp

BrilliantColor™

C.M.S. Setting [On/Off]

C.M.S.

Standard

Presentation

Movie

Game

sRGB*1

Picture Mode

Red

Blue

Page 42

DNR Off

Level 1

Level 2

Bright

Eco + Quiet

C.M.S.-Hue

C.M.S.-Saturation

C.M.S.-Value

Page 41

Reset

+30-30

Reset

Items when inputting RGB signal through

COMPUTER or DVI.

Items when inputting component signal through

COMPUTER or DVI, or when selecting S-VIDEO or

VIDEO.

PAGE 1

“Picture” menu

“C.M.S.”

SEL./ADJ.

Return

ENTER

END

C. M. S. - Hue

C. M. S. - Saturation

C. M. S. - Value

C. M. S.

Reset

Menu Items (Continued)

SEL./ADJ. ENTER END

Resize

Image Shift 0

Keystone

OSD Display

Background

Setup Guide

PRJ Mode

Language

Front

English

Logo

Border

Picture SCR - ADJ PRJ - ADJ Help

Closed Caption Off

Main menu Sub menu

SCR - ADJ

Page 43

Language

Image Shift

Resize

Page 43

Page 44

Keystone

OSD Display [On/Off]

Background

Setup Guide

[On/Off]

PRJ Mode

Logo

Blue

None

Page 44

Closed Caption Off

CC1

CC2

Front

Ceiling + Front

Rear

Ceiling + Rear

+80-80

+96-96

Normal

Full

Dot By Dot

Area Zoom

V-Stretch

Border

Stretch

Normal

Area Zoom

V-Stretch

Border

Stretch

COMPUTER/

DTV

VIDEO/

S-VIDEO

English

Deutsch

Español

Nederlands

Français

Italiano

Svenska

Português

polski

Magyar

Türkçe

“Screen adjustment (SCR-ADJ)” menu

SEL./ADJ. ENTER END

Auto Power Off

System Sound

System Lock

Auto Restart On

STANDBY Mode Standard

0 min0Lamp Timer(Life) 100%

Auto Sync On

Picture SCR - ADJ PRJ - ADJ Help

Speaker On

Audio Input Audio 1

RS-232C 9600bps

Fan Mode Normal

Disable

Main menu Sub menu

PRJ - ADJ

Page 45

STANDBY Mode

System Sound [On/Off]

Speaker [On/Off]

System Lock

[Enable/Disable]

Lamp Timer(Life)

Page 45

Auto Restart [On/Off]

Page 45

Auto Power Off [On/Off]

Page 45

Page 46

Page 47

Fan Mode

Page 46

Normal

High

RS-232C

Page 46

9600bps

115200bps

Audio Input

Page 46

Audio 1

Audio 2

Standard

Eco

Auto Sync [On/Off]

Page 45

“Projector adjustment (PRJ-ADJ)” menu

Useful

Features

SEL ENTER END

There is no picture or audio

Vertical stripes or flickering image appear

Data image is not centered

Color is faded or poor

Picture is dark

The image is distorted

Reset all adjustments to default settings

SEL.

Picture SCR - ADJ PRJ - ADJ Help

The items you can set with the “Help”

“Help” menu n Page 48

•Vertical stripes or flickering image appear

Auto Sync

Clock

Phase

• Data image is not centered

Auto Sync

H-Pos

V-Pos

• Color is faded or poor

COMPUTER/COMPONENT or DVI input

Signal type: Auto/RGB/Component

S-VIDEO or VIDEO input

Video System: Auto/PAL/SECAM/

NTSC3.58/NTSC4.43/

PAL-M/PAL-N/PAL-60

DVI (Digital) input

Dynamic range: Auto/Standard/Enhanced

* The selectable items vary depending on the in-

put signal and the selected input mode.

“Help” menu

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Press MENU/HELP.

• The “Picture” menu screen for the se-

lected input mode is displayed.

Example: “Picture” screen menu for

COMPUTER (RGB) input

Press Q or O and select “Picture”

to adjust.

Menu item

Picture Mode

Contrast 0

Bright

Standard

SEL./ADJ. ENTER END

Red

Blue

CLR Temp

BrilliantColor

C.M.S. Setting

C.M.S.

Lamp Setting

Bright

DNR

Off

Reset

Picture SCR - ADJ PRJ - ADJ Help

Adjustment buttons (P/R/O/Q)

MENU/HELP button

ENTER button

Adjustment buttons

(P/R/O/Q)

ENTER button

RETURN button

•Press RETURN to return

to the previous screen

when the menu is

displayed.

MENU/HELP button

Using the Menu Screen

Useful

Features

Press P or R and select “Bright”

to adjust.

• The selected item is highlighted.

•Press ENTER again to return to the pre-

vious screen.

Press O or Q to adjust the item

selected.

• The adjustment is stored.

Press MENU/HELP.

• The menu screen will disappear.

0Bright

Picture

SEL./ADJ. Rtn. Menu END

Picture Mode

Contrast 0

Standard

SEL./ADJ. Single ADJ END

Red

Blue

CLR Temp

BrilliantColor

C.M.S. Setting

C.M.S.

Lamp Setting

Bright

Reset

15Bright

Picture SCR - ADJ PRJ - ADJ Help

DNR

Off

Note

Picture Mode

Standard

SEL./ADJ. Single ADJ END

Resize

Image Shift 0

Keystone

Border

Picture Mode

Contrast 0

Standard

SEL./ADJ. END

Red

Blue

CLR Temp

BrilliantColor

C.M.S. Setting

C.M.S.

Lamp Setting

Bright

Reset

Bright 0

Picture SCR - ADJ PRJ - ADJ Help

DNR

Off

Items to be adjusted

• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”,

“FREEZE”, or “AV MUTE” functions.

Note

To adjust the projected

image while watching it

Press ENTER.

• The selected item (e.g. “Bright”) is dis-

played by itself at the bottom of the

screen.

•When pressing P or R, the following item

(“Red” after “Bright”) will be displayed.

The item displayed by itself

Press ENTER.

Picture Adjustment (“Picture” Menu)

Standard

Presentation

Movie

Game

*sRGB

Q PAGE1 Q PAGE2

Picture Mode

Contrast 0

Bright

Color

Tint

0Sharp

Standard

SEL./ADJ. ENTER END

Red

Blue

Picture SCR - ADJ PRJ - ADJ Help

For standard image

Brightens portions of image for

more enhanced presentations.

Gives natural tint to the

projected image.

Gives sharpness to the

projected image.

For high fidelity reproduction of

images from a computer.

Picture Mode

CLR Temp

BrilliantColor

C.M.S. Setting

C.M.S.

Standard

SEL./ADJ. ENTER END

Progressive

Lamp Setting

3D Progressive

Bright

DNR

Off

Reset

Picture SCR - ADJ PRJ - ADJ Help

Menu operation n Page 38

•

You can also press PICTURE MODE on the remote control to select the picture mode. (See page 33.)

• *sRGB is an international standard of color reproduction regulated by the IEC (International

Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are

displayed in a natural tint based on an original image, when “sRGB” is selected.

For additional information about the sRGB function, visit “http://www.srgb.com/”.

You cannot set the items, “Red”, “Blue”, “CLR Temp”, “BrilliantColor

”, when “sRGB” is selected.

Note

1 1

1 Selecting the Picture Mode

• When “sRGB” is selected, the projected image may become dark, but this does not indicate a

malfunction.

Info

• “sRGB” is displayed only when RGB signal is input.

•You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are

retained in memory.

–1

–

Bright

Eco + Quiet

Bright

The default settings of each item when selecting Picture Mode

–

CLR Temp

Selectable

items

Description

BrilliantColor

Lamp Setting

Useful

Features

2 Adjusting the Image

*1 Not displayed in the RGB input mode.

*2 Not adjustable/selectable when selecting “sRGB”.

*3 BrilliantColor™ uses Texas Instruments’

BrilliantColor™ technology. As the BrilliantColor™

level is increased, the image becomes brighter

while the color reproduction is kept at a high level.

Q button

For more

contrast.

For more

brightness.

For more color

intensity.

For making skin

tones greenish.

For more

sharpness.

For stronger red.

For stronger blue.

For making the

effect stronger.

Adjustment

items

Contrast

Bright

Color*

Tint*

Sharp*

Red*

Blue*

BrilliantColor

™*

O button

For less

contrast.

For less

brightness.

For less color

intensity.

For making skin

tones purplish.

For less

sharpness.

For weaker red.

For weaker blue.

For making the

effect weaker.

Note

• “Red”, “Blue”, “BrilliantColor

” and “CLR

Temp” cannot be set when “sRGB” is selected.

•To reset all adjustment items, select “Reset”

and press ENTER.

3 Adjusting the Color

Temperature

•Values on “CLR Temp” are only for general

standard purposes.

Note

Selectable

items

–1

Description

For lower color temperature for

warmer, reddish incandescent-like

images.

For higher color temperature for

cooler, bluish, fluorescent-like images.

Menu operation n Page 38

4 Adjusting the Colors

This function adjusts each of the six main colors

that comprise the color wheel, altering their

“Hue”, “Saturation”, or “Value”.

Selectable items

C.M.S.-Hue

C.M.S.-Saturation

C.M.S.-Value

Reset

Description

Sets the hue of the main colors.

Sets the saturation of the main

colors

Sets the brightness of the main

colors.

The adjustments of “Hue”,

“Saturation” and “Value” of all

colors are reset to the default

setting.

Adjusting “Hue”, “Saturation”, or “Value”.

1Select “On” for “C.M.S. Setting” in the “Picture”

menu and then press ENTER.

2Select “C.M.S.” in the “Picture” menu and then

press ENTER.

3Press P or R to select either “Hue”, “Saturation”, or

“Value” and then press ENTER.

4Select the color to be adjusted with P or R and

adjust it with O or Q.

Example of adjusting the “Hue”

• When “Saturation” is selected, the selected

color becomes

O: lighter. Q: thicker.

• When “Value” is selected, the selected color

becomes

O: darker. Q: brighter.

• To reset the adjustment values of each color

to the default settings, select “Reset” and press

ENTER.

Main colors

R (Red)

Y (Yellow)

G (Green)

C (Cyan)

B (Blue)

M (Magenta)

O button

Closer to magenta

Closer to red

Closer to yellow

Closer to green

Closer to cyan

Closer to blue

Q button

Closer to yellow

Closer to green

Closer to cyan

Closer to blue

Closer to magenta

Closer to red

5 Progressive

• In NTSC or PAL60Hz, even if the 3D Progres-

sive mode has been set, the three-two pull

down enhancement will be enabled automati-

cally when the film source has been entered.

• When the image is blurred or noisy, switch to

the optimal mode.

* The film source is a digital video recording with the

original encoded as is at 24 frames/second. The

projector can convert this film source to progres-

sive video at 60 frames/second with NTSC and

PAL60Hz or at 50 frames/second with PAL50Hz

and SECAM to play back a high-definition image.

Selectable

items

Progressive

Film Mode

Description

Useful to display fast-moving images

such as sports.

Useful to display relatively slow-

moving images such as drama and

documentary more clearly.

Reproduces the image of film source*

clearly. Displays the optimized image of

film transformed with three-two pull down

(NTSC and PAL60Hz) or two-two pull

down (PAL50Hz and SECAM) enhance-

ment to progressive mode images.

Note

7 Lamp Setting

• In the Eco + Quiet mode, the fan sound and

power consumption are lower than those in

the Bright mode. (Projection brightness de-

creases as shown in the chart.)

Note

Selectable

items

Eco + Quiet

Bright

Brightness and Power consumption

PG-F312X Approx. 60%

PG-F262X Approx. 70%

PG-F212X Approx. 80%

100%

Menu operation n Page 38

Picture Adjustment (“Picture” Menu)

(Continued)

Reducing Image Noise (DNR)

Set “DNR” to “Off” in the following cases:

• When the image is blurry.

• When the contours and colors of moving

images drag.

• When TV broadcasts with weak signals are

projected.

Note

Selectable

items

Off

Level 1

Level 2

Description

The DNR function is not activated.

Sets the DNR level for viewing a

clearer picture.

Video digital noise reduction (DNR) provides high

quality images with minimal dot crawl and cross

color noise.

• This function is available for 480I and 576I

signals using COMPUTER/COMPONENT or

DVI input.

• This function is available for all signals with

S-VIDEO and VIDEO input.

Info

Useful

Features

Adjusting the Projected Image

(“SCR - ADJ” Menu)

SEL./ADJ. ENTER END

Resize

Image Shift 0

Keystone

OSD Display

Background

Setup Guide

PRJ Mode

Language

Front

English

Logo

Closed Caption Off

Border

Picture SCR - ADJ PRJ - ADJ Help

1 Setting the Resize Mode

• For details of the Resize mode, see pages

30 and 31.

•You can also press RESIZE on the remote con-

trol to set the resize mode. (See page 30.)

Note

2 Adjusting the Image

Position

You can move the projected image vertically.

Q button

• This function only works in some RESIZE

modes. (See pages 30 and 31.)

Note

O button

Menu operation n Page 38

3 Keystone Correction

When the image is projected either from the top

or from the bottom towards the screen at an angle,

the image becomes distorted trapezoidally. The

function for correcting trapezoidal distortion is

called Keystone Correction.

Select “Keystone” on the “SCR-ADJ”

menu and adjust with the slide bar.

See page 28 for details of Keystone Correction.

• The Keystone Correction can be adjusted up

to an angle of approximately ±40 degrees

(when “Resize” is set to “Normal”).

•You can also press KEYSTONE on the remote

control or on the projector to adjust Keystone

Correction.

Note

O buttonQ button

4 Setting the On-screen

Display

Selectable

items

Off

Description

All on-screen displays are displayed.

INPUT/VOLUME/AV MUTE/FREEZE/

AUTO SYNC/RESIZE/PICTURE MODE/

ECO+QUIET/MAGNIFY/ “An invalid

button has been pressed.” are not

displayed.

The projector can switch the on-screen display

language among 17 languages.

Selectable items

Front

Ceiling + Front

Rear

Ceiling + Rear

Description

Normal image (Projected from

the front of the screen)

Inverted image (Projected

from the front of the screen

with an inverted projector)

Reversed image (Projected

from the rear of the screen or

with a mirror)

Reversed and inverted image

(Projected with a mirror)

Selecting the On-screen

Display Language

8 Reversing/Inverting

Projected Images

English

Deutsch

Español

Nederlands

Français

Italiano

Svenska

Português

polski

Magyar

Türkçe

Menu operation n Page 38

Selecting the Background

Image

Selectable items

Logo

Blue

None

Description

Sharp logo screen

Blue screen

—

See page 19 for details of Projection (PRJ) Mode.

Adjusting the Projected Image

(“SCR - ADJ” Menu) (Continued)

• “Closed Caption” is a system which allows

conversations, narration, and sound effects in

TV programs and home videos to be viewed

as captions on the screen.

• Not all programs and videos will offer closed

captioning. Please look for the symbol to

ensure that captions will be shown.

• Two channels are available: CH1 and CH2.

“Closed Caption” shows subscripts of dialogs

and commentaries of TV dramas and news

programs while allowing a clear view of the

picture.

5 5

5 Closed Caption

Selectable items

Off

CC1

CC2

Description

—

Closed Caption mode for CH1 data

Closed Caption mode for CH2 data

• This function enables the display of captions

(text content) which are standardized by the

Federal Communications Commission, an

independent US government agency.

• Closed Caption may malfunction (white blocks,

strange characters, etc.) if signal conditions are

poor or if there are problems at the broadcast

source. This does not necessarily indicate a

problem with the projector.

•

If any button is pressed to call up the on-screen

display while viewing a Closed Caption broadcast,

the closed captions will disappear momentarily.

Note

Selecting the Setup Guide

Selectable items

Off

Description

Displaying the Setup Guide

when turning the projector on.

Not displaying the Setup Guide.

Useful

Features

SEL./ADJ. ENTER END

Auto Power Off

System Sound

System Lock

Auto Restart On

STANDBY Mode Standard

0 min0Lamp Timer(Life) 100%

Speaker On

Audio Input Audio 1

RS-232C 9600bps

Fan Mode Normal

Disable

Auto Sync On

Picture SCR - ADJ PRJ - ADJ Help

Menu operation n Page 38

• When the Auto Power Off function is set to

“On”, 5 minutes before the projector enters

standby mode, the message “Enter STANDBY

mode in X min.” will appear on the screen to

indicate the remaining minutes.

Selectable

items

Off

Description

When no input signal is detected for

more than 15 minutes, the projector will

automatically enter standby mode.

The Auto Power Off function will be

disabled.

Note

Auto Power Off Function

6 Speaker Setting

Setting the Confirmation

Sound (System Sound)

Selectable

items

Off

Description

A confirmation sound is made when

the projector turns on/off.

No confirmation sound is made.

When set to “Eco”, power consumption is

reduced in standby mode.

4 4

4 STANDBY Mode

Selectable

items

Off

Description

The audio signal is output from the

internal speaker.

The audio signal is not output from the

internal speaker.

Selectable

items

Eco

Standard

Description

The monitor output and RS-232C

functions are switched off in standby

mode.

The monitor output and RS-232C

functions are activated even if the

projector is in standby mode.

• Auto Sync adjustment is also performed by

pressing AUTO SYNC on the remote control.

• The Auto Sync adjustment may take some time

to complete, depending on the image of the

computer connected to the projector.

• When the optimum image cannot be achieved

with Auto Sync adjustment, use manual

adjustments. (See page 48.)

Selectable

items

Off

Description

Auto Sync adjustment will occur when

the projector is turned on or when the

input signals are switched, when

connected to a computer.

Auto Sync adjustment is not

automatically performed.

Note

Auto Sync (Auto Sync

Adjustment)

3 Auto Restart Function

Selectable

items

Off

Description

If the power cord is unplugged from the

outlet or the breaker switch is turned off

when the projector is on, then the

projector automatically turns on when

the power cord is plugged into the AC

outlet or the breaker switch is turned on.

The projector does not turn on

automatically when the power cord is

plugged into the AC outlet or the

breaker switch is turned on.

Adjusting the Projector Function (“PRJ - ADJ” Menu)

(Continued)

Info

•

If you lose or forget your keycode, contact

your nearest Sharp Authorized Projector

Dealer or Service Center (see page 66). Even

if the product warranty is valid, the keycode

reset will incur a charge.

0 0

0 System Lock Function

This function prevents unauthorized use of the

projector. Once this function is activated, users

must enter the correct keycode each time the

projector is turned on. We suggest you record

the keycode in a safe place where only au-

thorized users have access.

9 9

9 Fan Mode Setting

This function changes the fan rotation speed.

Menu operation n Page 38

Selectable

items

Normal

High

Description

Suitable for normal environments.

Select this when using the projector at

altitudes of approximately 1,500

meters (4,900 feet) or more.

Selecting the Transmission

Speed (RS-232C)

Make sure that both the projector and computer

are set for the same baud rate.

Selectable

items

9600bps

115200bps

Description

Transmission speed is slow.

Transmission speed is rapid.

a Setting/Changing the keycode

When “Fan Mode” is set to “High”, the fan rotation

speeds up, and the fan noise becomes louder.

Select “System Lock”, then press

ENTER or Q.

Select “Next”, then press ENTER.

• The screen for entering the keycode

appears.

Monitor Output

This function allows you to select an appropriate

combination of audio input terminals for each

input mode.

7 7

7 Audio Input

Selectable

items

Audio 1

Audio 2

Description

The AUDIO 1 input terminal is used as

an audio input terminal.

The AUDIO 2 input terminal is used as

an audio input terminal.

Press the 4 buttons on the remote

control or on the projector to enter

the preset keycode in “Old Code”.

•

When setting the keycode for the first time,

press R on the projector for four times.

Setting the System Lock

PRJ - ADJ

Old Code

New Code

Reconfirm

––––

• If you input a wrong keycode, the cursor

returns to the first point of the “Old Code”.

• The preset keycode is 4 R buttons on

the projector. When you press the R but-

ton four times, the keycord input screen

disappears.

Note

•You cannot use the following buttons for

keycode:

STANDBY/ON,

, STANDBY,

ENTER

L-CLICK

R-CLICK/RETURN

and MENU/HELP

•

System lock function recognizes each

button on the remote control or on the

projector as an individual button, even if

they share the same button name. If you

used the buttons on the projector in

setting your keycode, the keycode cannot

be canceled with the remote control.

Press the 4 buttons on the remote

control or on the projector to enter

the new keycode in “New Code”.

Setting the System Lock

PRJ - ADJ

Old Code

New Code

Reconfirm

****

– –––

––––

Note

Useful

Features

Note

Input screen for keycode

To cancel the keycode that you have already

set

•Press R on the projector for four times in steps

4 and 5 above.

When the System Lock is set

• When System Lock is set, the keycode input

screen appears after the power is turned on.

When it appears, enter the right keycode to

start projection.

Enter the same keycode in “Re-

confirm”.

System Lock

––––

Locking the Operation

Buttons on the Projector

Use this function to lock the operation buttons

on the projector.

a Taking the Keylock off

Hold down ENTER on the projector for about 5

seconds.

On-screen display

a Locking the Operation Buttons

Hold down ENTER on the projector for about 5

seconds while the projector is being turned on.

On-screen display

• The keylock function does not affect the opera-

tion with the remote control buttons.

•You cannot use the keylock function while the

projector is warming up.

• When the projector is in standby mode, you can

release the keylock by holding down ENTER

and STANDBY/ON on the projector simulta-

neously for about 5 seconds.

Keylock Function

• Keylock cannot be set while the projector is:

displaying the “Setup Guide” or “Menu”

screens, in standby mode, warming up, chang-

ing input signals, operating “Auto Sync”

function, in “FREEZE” mode or on the “System

Lock” screen during warming up.

Info

Checking the Lamp Life

Status

You can confirm the cumulative lamp usage time

and the remaining lamp life (percentage).

Lamp usage condition

Operated exclusively

with Lamp Setting set to

“Eco +Quiet”

Operated exclusively

with Lamp Setting set to

“Bright”

100%

Approx.

X,XXX

hours

Approx.

X,XXX

hours

Approx.

XXX hours

Approx.

XXX hours

Remaining lamp life

“Life”

Note

• It is recommended that the lamp be changed

when the remaining lamp life becomes 5%.

• The lamp life may vary depending on the us-

age condition.

Troubleshooting with the “Help” Menu

Utilizing the “Help” Menu

Functions

This function advises you to solve the problems during usage.

•You can adjust the items with check marks (✔).

• The items in the “Help” menu change, de-

pending on the input signal or setting that you

have selected.

• If the problem is not solved, refer to

“Troubleshooting” (see pages 64 and 65).

• When selecting “sRGB” in “Picture Mode”, the

item “Color is faded or poor” is not displayed.

This means you cannot change input signal

types.

Press O or Q to adjust.

If the image is not improved, se-

lect “Adjust horizontal noise”,

then press ENTER.

Select “Initiate “Auto Sync” Ad-

justments”, then press ENTER.

Press P or R to select “Vertical

stripes or flickering image ap-

pears” on Help menu, then press

ENTER.

Example: When image flickering appears

Operation to solve image flickering when pro-

jecting the computer RGB signal.

Note

Press MENU/HELP.

Press O or Q to select “Help”, then

press ENTER.

Adjustment buttons

(P/R/O/Q)

ENTER button

MENU/HELP

button

0Phase

SEL./ADJ. Rtn. Menu END

Help

If there is no change after performing "Auto Sync"

adjustments, adjust the following items.

Initiate “Auto Sync” Adjustments.

Vertical stripes or flickering image appear

Adjust vertical noise

Adjust horizontal noise

Reset the 2 items above

Return

Signal Info 1024✤✤✤✤768

H 48.3 kHz / V 59.9 Hz

SEL. ENTER END

There is no picture or audio

Vertical stripes or flickering image appear

Data image is not centered

Color is faded or poor

Picture is dark

The image is distorted

Reset all adjustments to default settings

SEL. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

Help

Vertical stripes or flickering image appear

Press ENTER.

Appendix

Cleaning the lens

■ Use a commercially available blower or lens

cleaning paper (for glasses and camera lenses)

for cleaning the lens. Do not use any liquid type

cleaning agents, as they may wear off the

coating film on the surface of the lens.

■ As the surface of the lens can easily get

damaged, be careful not to scrape or hit the

lens.

Cleaning the exhaust and intake vents

■ Use a vacuum cleaner to clean dust from the

exhaust vent and the intake vent.

Cleaning the projector

■ Ensure that you have unplugged the power

cord before cleaning the projector.

■ The cabinet as well as the operation panel is

made of plastic. Avoid using benzene or

thinner, as these can damage the finish on the

cabinet.

■ Do not use volatile agents such as insecticides

on the projector.

Do not attach rubber or plastic items to the

projector for long periods.

The effects of some of the agents in the plastic

may cause damage to the quality or finish of the

projector.

■ Wipe off dirt gently with a soft flannel cloth.

■ When the dirt is hard to remove, soak a cloth in

a mild detergent diluted with water, wring the

cloth well and then wipe the projector.

Strong cleaning detergents may discolor, warp

or damage the coating on the projector. Make

sure to test on a small, inconspicuous area on

the projector before use.

Maintenance

• If you want to clean the air vents during projec-

tor operation, ensure you press STANDBY/ON

on the projector or STANDBY on the remote

control and put the projector into standby

mode. After the cooling fan has stopped, clean

the vents.

Info

Wax

Mild detergent

Mild detergent diluted

with water

Thinner

Maintenance Indicators

About the lamp indicator

■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be

displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will

automatically turn off and then the projector will automatically enter standby mode. At this time, the

lamp indicator will illuminate in red.

■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will

not turn on.

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,

“ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp

will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec-

tor will enter standby mode. After “ ” appears, ensure you perform the measures described on

page 51.

■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the

projector indicate problems inside the projector.

■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate

red, and the projector will enter standby mode. After the projector has entered standby mode,

follow the procedures given below.

Red on

Green on

Red blinks

Green blinks

Green on

Green blinks

Red on

Off

Red on

Power indicator

Lamp indicator

Temperature warning

indicator

Indicators on the Projector

Normal (Standby)

Normal (Power on)

Abnormal (See page 51.)

Normal (Cooling)

Normal

The lamp is warming up.

The lamp is shut down abnormally or requires to be

changed. (See page 51.)

Normal

The internal temperature is abnormally high. (See page 51.)

Top View

Lamp indicator

Temperature warning

indicator

Power indicator

Regarding the Lamp

Lamp

■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes

5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life

(percentage) can be checked with the on-screen display. (See page 47.)

■ Purchase a replacement lamp of type AN-F212LP from your place of purchase, nearest Sharp

Authorized Projector Dealer or Service Center.

Caution Concerning the Lamp

■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp

failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface

scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition

and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended

that the lamp be replaced with a new one immediately, even if the lamp appears to be operating

normally.

■ Should the lamp break, there is also a possibility that glass particles may spread inside of the

projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector

Dealer or Service Center to assure safe operation.

■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the

lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes

mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case

of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

Caution

• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may

cause burns or injury.

•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully

cool before removing the lamp unit.

■ Carefully change the lamp by following the instructions described in this section. * If you wish,

you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service

Center.

* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized

Projector Dealer or Service Center for repair.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited

warranty. All service of this projector under warranty, including lamp replacement,

must be obtained through a Sharp Authorized Projector Dealer or Service Center.

For the name of the nearest Sharp Authorized Projector Dealer or Service Center,

please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal

Information

www.lamprecycle.org or 1-800-BE-SHARP

U.S.A. ONLY

Appendix

Removing and Installing

the Lamp Unit

• Do not touch the glass surface of the lamp

unit or the inside of the projector.

•To avoid injury to yourself and damage to the

lamp, make sure you carefully follow the steps

below.

• Do not loosen other screws except for the

lamp unit cover and lamp unit.

Press STANDBY/ON on the projec-

tor or STANDBY on the remote

control to put the projector into

standby mode.

•Wait until the cooling fan stops.

Warning!

• Do not remove the lamp unit from the projec-

tor right after use. The lamp and parts around

the lamp will be very hot and may cause burns

or injury.

Disconnect the power cord.

• Unplug the power cord from the AC

socket.

• Leave the lamp until it has fully cooled

down (about 1 hour).

Remove the lamp unit cover.

•Turn the projector over. Loosen the user

service screw (1) that secures the lamp

unit cover. Remove the lamp unit cover

(2).

Lamp unit

AN-F212LP

Info

Optional

accessory

AC socket

User service screw

(for lamp unit cover)

STANDBY/ON button

Remove the lamp unit.

• Loosen the securing screws from the

lamp unit. Hold the lamp unit and pull it

in the direction of the arrow. At this time,

keep the lamp unit horizontal and do not

tilt it.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Insert the new lamp unit.

•Press the lamp unit firmly into the lamp

unit compartment. Fasten the securing

screws.

Replace the lamp unit cover.

• Align the tab on the lamp unit cover

(1) and place it while pressing the tab

(2) to close it. Then tighten the user ser-

vice screw (3) to secure the lamp unit

cover.

Connect the power cord.

• Plug the power cord into the AC socket

of the projector.

Reset the lamp timer.

• While simultaneously holding down

MENU/HELP, ENTER and R on the pro-

jector, press STANDBY/ON on the pro-

jector.

• “LAMP 0000H” is displayed, indicating

that the lamp timer is reset.

• Make sure to reset the lamp timer only when

replacing the lamp. If you reset the lamp timer

and continue to use the same lamp, this may

cause the lamp to become damaged or ex-

plode.

Info

AC socket

• If the lamp unit and lamp unit cover are

not correctly installed, the power will not

turn on, even if the power cord is con-

nected to the projector.

Info

Regarding the Lamp (Continued)

Securing screws

ENTER button

MENU/HELP

button

R button

STANDBY/ON

button

Appendix

Storing the Projector

Info

How to Use the Storage Case

When storing the projector, attach the lens cap

to the lens, and place it in the supplied storage

case.

Open the cover of the storage

case.

• Ensure the projector has cooled down

sufficiently before placing it in the case.

• When you place the projector into the

storage case, make sure that the

cooling fan has stopped.

• Ensure the lens cap is attached to the

lens for protection.

• Place the projector into the storage

case with the lens facing the handle.

• Ensure the projector is held in place by

using the fixing band.

• Do not expose the storage case to

direct sunlight or near heat sources. The

storage case may change color or

become deformed.

Close the cover of the storage

case.

Place the projector into the stor-

age case.

Place the accessories in the front

pocket of the storage case.

Lens cap

Fixing band

Supplied accessories

(Rremote control, etc.)

COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals : mini D-

sub 15 pin female connector

COMPUTER Input/Output

Pin No. Signal

1. Video input (red)

2. Video input (green/sync on green)

3. Video input (blue)

4. Not connected

5. Not connected

6. Earth (red)

7. Earth (green/sync on green)

8. Earth (blue)

9. Not connected

10. GND

11. Not connected

12. Bi-directional data

13. Horizontal sync signal: TTL level

14. Vertical sync signal: TTL level

15. Data clock

COMPONENT Input/Output

Pin No. Signal

1. PR (CR)

2. Y

3. PB (CB)

4. Not connected

5. Not connected

6. Earth (PR)

7. Earth (Y)

8. Earth (PB)

9. Not connected

10. Not connected

11. Not connected

12. Not connected

13. Not connected

14. Not connected

15. Not connected

1823

DVI-I Terminal : 29 pin connector

• DVI Digital Input

Pin No. Signal Pin No. Signal

1. T.M.D.S data 2– 16. Hot plug detection

2. T.M.D.S data 2+ 17. T.M.D.S data 0–

3. T.M.D.S data 2 shield 18. T.M.D.S data 0+

4. Not connected 19. T.M.D.S data 0 shield

5. Not connected 20. Not connected

6. DDC clock 21. Not connected

7. DDC data 22. T.M.D.S clock shield

8. Not connected 23. T.M.D.S clock+

9. T.M.D.S data 1– 24. T.M.D.S clock–

10. T.M.D.S data 1+ C1. Not connected

11. T.M.D.S data 1 shield C2. Not connected

12. Not connected C3. Not connected

13. Not connected C4. Not connected

14. +5V power C5. Ground

15. Ground

• DVI Analog RGB Input

Pin No. Signal Pin No. Signal

1. Not connected 16. Hot plug detection

2. Not connected 17. Not connected

3. Not connected 18. Not connected

4. Not connected 19. Not connected

5. Not connected 20. Not connected

6. DDC clock 21. Not connected

7. DDC data 22. Not connected

8. Vertical sync 23. Not connected

9. Not connected 24. Not connected

10. Not connected C1. Analog input Red

11. Not connected C2. Analog input Green

(Sync On Green)

12. Not connected C3. Analog input Blue

13. Not connected C4. Horizontal sync

(Composite Sync)

14. +5V power C5. Ground

15. Ground

• DVI Analog Component Input

Pin No. Signal Pin No. Signal

1. Not connected 16. Not connected

2. Not connected 17. Not connected

3. Not connected 18. Not connected

4. Not connected 19. Not connected

5. Not connected 20. Not connected

6. Not connected 21. Not connected

7. Not connected 22. Not connected

8. Not connected 23. Not connected

9. Not connected 24. Not connected

10. Not connected C1. Analog input Pr/Cr

11. Not connected C2. Analog input Y

12. Not connected C3. Analog input Pb/Cb

13. Not connected C4. Not connected

14. Not connected C5. Ground

15. Ground

Connecting Pin Assignments

Appendix

RS-232C Terminal : mini DIN 9 pin female connector

Signal Name

Pin No.

I/O Reference

Not connected

Connected to internal circuit

Not connected

Connected to internal circuit

Not connected

Connected to CS in internal circuit

Connected to RS in internal circuit

Not connected

Receive Data

Send Data

Signal Ground

Request to Send

Clear to Send

Input

Output

RS-232C Terminal : D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor

Signal NamePin No.

I/O Reference

Not connected

Connected to internal circuit

Not connected

Connected to internal circuit

Not connected

Connected to CS in internal circuit

Connected to RS in internal circuit

Not connected

Receive Data

Send Data

Signal Ground

Request to Send

Clear to Send

Input

Output

SignalPin No.

RS-232C Cable recommended connection : D-sub 9 pin female connector

SignalPin No.

USB Terminal : Type B USB connector

VCC

USB–

USB+

Signal NamePin No.

USB power

USB data–

USB data+

Signal Ground

Projector

Pin No.

Computer

Pin No.

• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the

controlling device (e.g. computer).

Note

Info

• When controlling the projector using RS-232C commands from a computer, wait for at least 30

seconds after the power has been turned on, and then transmit the commands.

• After sending an input selection or picture adjustment command and then receiving an “OK” re-

sponse code, the projector may take some time to process the command. If a second command is

sent while the projector is still processing the first command, you may receive an “ERR” response

code. If this happens, try resending the second command.

• When more than one code is being sent, send each command only after the response code for the

previous command from the projector is verified.

• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1”

“TLTM _ _ _ 1” “TLTL _ _ _ 1” “TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”

- When the projector receives the special commands shown above:

* The on-screen display will not disappear.

* The “Auto Power Off” timer will not be reset.

- The special commands are available for applications that require continuous polling.

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control

cable (cross type, commercially available) to the projector. (See page 24 for connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table.

Signal format: Conforms to RS-232C standard. Parity bit: None

Baud rate*: 9,600 bps / 115,200 bps Stop bit: 1 bit

Data length: 8 bits Flow control: None

*Set the projector’s baud rate to the same rate as used by the computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and

return code. After the projector processes the command from the computer, it sends a re-

sponse code to the computer.

RS-232C Specifications and Commands

Return code (

0DH

)

C1 C2 C3 C4 P1 P2 P3 P4

Response code format

Normal response

Problem response (communication error or incorrect command)

O K

E R R

Command 4-digit Parameter 4-digit

Command format

Return code (

0DH

)

Return code (

0DH

)

• If an underbar (_) appears in the parameter column, enter a space.

• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets

under Control Contents.

*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.

*2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response

code is received.

*3 The Lamp Timer Reset command is available only in standby mode.

Note

Appendix

Computer

Computer Compatibility Chart

• Multiple signal support

Horizontal Frequency: 15-110 kHz,

Vertical Frequency: 45-85 Hz,

The following is a list of modes that conform to VESA. However, this projector supports other

signals that are not VESA standards.

27.0

31.5

37.5

27.0

31.5

37.9

27.0

31.5

27.0

31.5

37.9

26.2

31.5

34.7

37.9

37.5

43.3

31.4

35.2

37.9

46.6

48.1

46.9

53.7

40.3

48.4

56.5

60.0

68.7

45.0

47.8

49.7

62.8

47.7

47.8

55.0

66.2

67.5

64.0

80.0

64.0

65.3

75.0

34.9

49.7

60.2

68.7

640 × 350

640 × 400

720 × 350

720 × 400

640 × 480

800 × 600

1024 × 768

1280 × 720

1280 × 768

1280 × 800

1360 × 768

1366 × 768

1152 × 864

1280 × 1024

1400 × 1050

1600 × 1200

640 × 480

832 × 624

1024 × 768

1152 × 870

MAC 13"

MAC 16"

VGA

SVGA

XGA

WXGA

SXGA

SXGA+

UXGA

VGA

SVGA

XGA

SXGA

✔

PC/MAC

Intelligent Compression

MAC 19"

MAC 21"

Resolution

Horizontal Frequency

(kHz)

Vertical Frequency

(Hz)

VESA Standard

DVI-D

Support

Display

Upscale

True

Intelligent

Compression

Upscale

True

Pixel Clock: 12-170 MHz

Sync signal: Compatible with TTL level

• Compatible with sync on green signal

• When this projector receives 640K350 VESA format VGA signals, “640 × 400” appears on the screen.

• Optimum image quality will be achieved by matching your computer’s output resolution to the

resolution that corresponds to “True” in the “Display” column shown above.

Note

DTV

Signal

480I

480P

540P

576I

576P

720P

1035I

1080I

1080P

Horizontal Frequency (kHz)

15.7

31.5

33.8

15.6

31.3

37.5

45.0

33.8

28.1

33.8

27.0

56.3

67.5

Ver tical Frequency (Hz)

DVI-D Support (Compatible with HDCP)

✔

(DVI-D only)

Troubleshooting

Problem Check

•Projector power cord is not plugged into the wall outlet.

• Power to the external connected devices is off.

• The selected input mode is wrong.

• Cables are incorrectly connected to the projector.

• Remote control battery has run out.

•

External output has not been set when connecting notebook computer.

• The lamp unit cover is not installed correctly.

•

If the connected DVI digital equipment is turned on before the “DVI-D”

input mode is selected on the projector, the image may not be

projected properly or may not be displayed at all. Ensure that the

appropriate input mode has been selected on the projector before you

turn on the connected equipment.

• Cables are incorrectly connected to the projector.

• “Bright” is set to minimum position.

• Depending on the computer you are using, an image may not be

projected unless the signal output setting of the computer is

switched to the external output. Refer to the computer’s operation

manual for how to switch its signal output settings.

• Image adjustments are incorrectly set.

• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower

the “BrilliantColor

” value.

(Video Input only)

•Video input system is incorrectly set.

• Adjust the focus.

• The projection distance exceeds the focus range.

•

There is fog on the lens. If the projector is carried from a cold room into a

warm room, or if it is suddenly heated, condensation may form on the

surface of the lens and the image will become blurred. Set up the

projector at least one hour before it is to be used. If condensation should

form, remove the power cord from the wall outlet and wait for it to clear.

(Computer Input only)

• Perform “Fine Sync” Adjustments (“Clock” Adjustment)

• Perform “Fine Sync” Adjustments (“Phase” Adjustment)

• Noise may appear depending on the computer.

• Cables are incorrectly connected to the projector.

•Volume is set to minimum.

• When the projector is connected to an external device and the

volume is set to minimum, the sound is not output even if you turn up

the volume of the external device.

• “Speaker” is set to “Off”.

• Select “Data image is not centered” in the “Help” menu and make the

necessary adjustments.

• Depending on the computer you are using, the output resolution

signal may be different from the one you have set. For details, refer to

the operation manual of the computer.

Page

–

21–24

53, 54

21–24

–

21–24

–

Color is faded or poor.

Picture appears but no

sound is heard.

Picture is blurred;

noise appears.

Sound is heard but no

picture appears

(or picture is dark).

No picture and no sound

or projector does not

start.

Data image is not

centered.

Appendix

Problem

An unusual sound is

occasionally heard from

the cabinet.

Maintenance indicator on

the projector illuminates

or blinks in red.

The projector cannot

be turned on or put into

the standby mode

using STANDBY/ON on

the projector.

Picture is green on

COMPUTER

(Component)/

DVI (Component).

Picture is pink

(no green) on

COMPUTER (RGB)/

DVI (RGB).

Picture is too bright and

whitish.

The cooling fan becomes

noisy.

The lamp does not light

up even after the

projector turns on.

The lamp suddenly turns

off during projection.

The image sometimes

flickers.

The lamp needs much

time to turn on.

Picture is dark.

The remote control

cannot be used.

Check

• If the picture is normal, the sound is due to cabinet shrinkage caused

by room temperature changes. This will not affect operation or

performance.

• See “Maintenance Indicators”.

• The keylock is set.

If the keylock is set to “ON”, all the buttons are locked.

• Change the input signal type setting.

• When you cannot select an input signal type, select “Color is faded

or poor” in the “Help” menu, after selecting an item other than

“sRGB” in “Picture Mode”, and then select an input signal type.

• Image adjustments are incorrectly set.

• When temperature inside the projector increases, the cooling fan

runs faster.

• The lamp indicator is illuminating in red.

Replace the lamp.

• Cables are incorrectly connected to the projector or the connected

equipment works improperly.

• Select “Vertical stripes or flickering image appear” in the “Help”

menu and make the necessary adjustments.

• If this happens frequently, replace the lamp.

• The lamp will eventually need to be changed.

While the remaining lamp life draws to a close, replace the lamp.

• Operate the remote control while pointing it at the projector’s remote

control sensor.

• The remote control may be too far away from the projector.

• If direct sunlight or a strong fluorescent lamp is shining on the

projector’s remote control sensor, place the projector where it will not

be affected by strong light.

• The batteries may be depleted or inserted incorrectly. Make sure the

batteries are inserted correctly or insert new ones.

Page

–

40, 48

8, 9

49, 50, 51

50, 53

21–24

This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation

or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.

Dimensions

Units: inches (mm)

(89)

(37.65)

(66.35)

(75)

(270)

(60)

(265)

(6)

(10)

M4 M4

(104)

(49)

(10)

(30)

(75)

(36)

Appendix

Accessories ............................................................. 10

AC socket ................................................................ 24

Adjustment buttons ................................................. 38

AREA ZOOM ........................................................... 31

Aspect ratio ............................................................. 30

Audio Input .............................................................. 46

AUDIO 1, 2 terminal ................................................ 23

AUDIO OUT terminal .............................................. 23

Auto Power Off ........................................................ 45

Auto Restart ............................................................ 45

Auto Sync (Auto Sync adjustment) ....... 33, 37, 45, 48

AUTO SYNC button ................................................. 33

AV MUTE button ...................................................... 29

Background ............................................................. 44

Batteries .................................................................. 14

Blue .......................................................................... 41

BORDER ........................................................... 30, 31

BREAK TIMER button ............................................. 32

Bright ....................................................................... 41

BrilliantColor

......................................................... 41

Closed Caption ........................................................ 44

CLR Temp (Color Temperature) .............................. 41

C.M.S. ...................................................................... 41

Color ........................................................................ 41

COMPUTER button ................................................. 29

COMPUTER/COMPONENT input terminal ...... 21, 22

Contrast ................................................................... 41

DIN-D-sub RS-232C adaptor .................................. 24

DNR ......................................................................... 42

DOT BY DOT ........................................................... 30

DVI button ................................................................ 29

DVI-I input terminal ........................................... 21, 22

ECO+QUIET button ................................................ 32

ENTER button ......................................................... 38

Exhaust vent ...................................................... 12, 49

Fan Mode ................................................................. 46

Fine Sync ................................................................. 48

Focus ring ................................................................ 26

FREEZE button ....................................................... 33

Front adjustment foot .............................................. 27

FULL ........................................................................ 30

HEIGHT ADJUST lever ........................................... 27

Help ......................................................................... 48

H-Pos ................................................................. 37, 48

Image shift ............................................................... 43

INPUT modes .......................................................... 29

Intake vent ......................................................... 11, 49

Kensington Security Standard connector ............... 12

Keycode ................................................................... 46

Keylock .................................................................... 47

KEYSTONE button .................................................. 28

Keystone Correction .......................................... 28, 43

Lamp ........................................................................ 52

Lamp indicator ......................................................... 50

Lamp Setting ........................................................... 42

Lamp Timer (Life) .................................................... 47

Lamp unit ................................................................. 53

Language (on-screen display language) ................ 44

Index

L-CLICK button ........................................................ 34

Lens Cap ................................................................. 11

MAGNIFY buttons ................................................... 33

MENU/HELP button .......................................... 38, 48

MONITOR OUT terminal ......................................... 23

MOUSE/Adjustment buttons ............................. 34, 38

NORMAL ........................................................... 30, 31

ON button ................................................................ 25

Optional accessories ............................................... 10

OSD Display ............................................................ 43

PAGE DOWN button ................................................ 34

PAGE UP button ...................................................... 34

PDF ............................................................................ 9

Picture Adjustment .................................................. 40

Picture Mode ..................................................... 33, 40

PICTURE MODE button .......................................... 33

POINTER button ..................................................... 32

Power cord ............................................................... 24

Power indicator ........................................................ 50

PRJ - ADJ ................................................................ 45

PRJ Mode .......................................................... 19, 44

Progressive .............................................................. 42

R-CLICK/RETURN button ................................. 34, 38

Rear adjustment foot ............................................... 27

Red .......................................................................... 41

Remote control ........................................................ 13

Remote control sensor ............................................ 15

Replacing the lamp ........................................... 52, 53

Resize ................................................................ 30, 43

RESIZE button ........................................................ 30

RGB cable ............................................................... 21

RS-232C terminal .................................................... 24

SCR - ADJ ............................................................... 43

Screen Size and Projection Distance ..................... 20

Setup Guide ....................................................... 26, 44

Sharp ....................................................................... 41

Speaker ................................................................... 45

SPOT button ............................................................ 32

STANDBY button ..................................................... 25

STANDBY Mode ...................................................... 45

STANDBY/ON button .............................................. 25

Storage case ........................................................... 55

STRETCH .......................................................... 30, 31

Supplied accessories .............................................. 10

S-VIDEO button ....................................................... 29

S-VIDEO terminal .................................................... 22

System Lock ............................................................ 46

System Sound ......................................................... 45

Temperature warning indicator ............................... 50

Tint ........................................................................... 41

USB terminal ........................................................... 34

VIDEO button .......................................................... 29

VIDEO terminal ....................................................... 22

VOL (Volume) buttons ............................................. 29

V-Pos ................................................................. 37, 48

V-STRETCH ............................................................ 31

Zoom ring ................................................................ 26

Sharp pg f312x Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Sharp pg f312x

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info