Handleiding Sharp dv 740 (pagina 4 van 36) (Engels)

138267

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

- 1 -

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 1.6 A fuse.

Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of

the

same rating as above, which is also indicated on the pin face of the plug, must be used.

Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.

In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-

off

the mains plug and fit an appropriate type.

DANGER: The fuse from the cut-off plug should be removed and the cut-

off plug destroyed immediately

and disposed of in a safe manner.

Under no circumstances should the cut-

off plug be inserted elsewhere into a 13 A socket

outlet, as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the instruction below:

IMPORTANT: The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this product may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured

black.

? The wire which is coloured brown must be connected to the plug terminal which is marked L or

coloured red.

Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.

Before replacing the plug cover make sure that:

? If the new fitted plug contains a fuse, Its value is the same as that removed from the cut-off plug.

? The cord grip is clamped over the sheath of the mains lead and not simply over the lead wires.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

- 2 -

SAFETY INFORMATION

Power Lead Protection

To avoid any malfunctions of the unit, and to protect against

electric shock, fire or personal injury, please observe the

following,

l Hold the plug firmly when connecting or disconnecting

the AC power lead.

l Keep the AC power lead away from heating

appliances.

l Never put any heavy object on the AC power lead.

l Do not attempt to repair or reconstruct the AC power

lead in any way.

l This player is classified as a CLASS 1 LASER product.

l The CLASS 1 LASER PRODUCT is located on the rear

cover.

l This product contains a low power laser device. To

ensure continued safety do not remove any cover or

attempt to gain access to the inside of the product.

Refer all servicing to qualified personnel.

(Rear of product)

Note:

This unit can be used only where the power supply is

AC 220V-240V, 50/60Hz. It cannot be used

elsewhere.

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

AS THE LASER BEAM USED IN THIS PLAYER IS

HARMFUL TO THE EYES, DO NOT ATTEMPT TO

DISASSEMBLE THE CABINET. REFER

SERVICING TO QUALIFIED PERSONNEL ONLY.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO

RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, AND ANNOYING INTERFERENCE, USE

THE RECOMMENDED ACCESSORIES ONLY.

Laser Diode Properties

Material: AlGalnP

Wave length: DVD 650 ± 15 nm

CD 790 ± 20 nm

Emission Duration: Continuous

Laser output: Max. 0.5 mW

- 3 -

SAFETY INFORMATION

Location and Handling

l Do not place your Player in enclosed space or do not

cover it to prevent excessive temperatures inside the

unit.

l Do not place the Player in direct sunlight, or near heat

sources.

l Keep the Player away from magnetic fields, i.e.

loudspeakers etc.

l Do not place any object containing water or other

liquids on the Player. In the event that liquid should

enter the cabinet, unplug the Player immediately and

contact the retailer or service centre approved by

SHARP immediately.

l Do not remove the Player cabinet. Touching parts

inside the cabinet could result in electric shock and/or

damage to the Player. For service and adjustment

inside the cabinet, call a qualified dealer or service

centre approved by SHARP.

Periods of no use

When the unit is not being used, switch the unit to the

Standby mode.

When left unused for a long period of time, the unit should

be unplugged from the household AC socket.

No Fingers or Other Objects Inside

Do not put any foreign object on the disc tray.

Stacking

Place the unit in a horizontal position, and do not place

anything heavy on it.

Condensation

Moisture may form on the pickup lens in the following

conditions:

l Immediately after a heater has been turned on.

l In a steamy or very humid room.

l When the unit is suddenly moved from a cold

environment to a warm one.

If moisture forms inside this unit, it may not operate

properly.

In this case, turn on the power and wait about one hour for

the moisture to evaporate.

Cleaning

Unplug your Player before cleaning. Use a damp cloth for

cleaning. Do not use cleaning fluids or aerosols which

could enter the unit and cause damage, fire, or electrical

shock. These substances may also deteriorate the finish of

your Player.

If there is Noise Interference on the TV While

a Broadcast is being Received

Depending on the reception condition of the TV,

interference may appear on the TV monitor while you watch

a TV broadcast and the unit is left on. This is not a

malfunction of the unit or the TV. To watch a TV broadcast,

turn off the unit.

Service

Do not attempt to service this Player yourself. Please refer

any service to the nearest service centre approved by

SHARP.

Recording and playback of any material may require

consent.

Please refer particularly to the provisions of the Copyright

Act 1956, the Dramatic and Musical Performers Protection

Act 1958, the Performers Protection Acts 1963 and 1972

and to any subsequent statutory enactments and orders.

Copy Protection

This DVD video player supports Macrovision copy protection.

On DVDs that include a copy protection code, if the contents of

the DVD are copied using a VCR, the copy protection code

prevents the videotape copy from playing normally.

Recommended Measures for Optimum

Picture Excellence

The unit is a precision device that is constructed using

extremely accurate technology.

Soiling or friction affecting the pickup lens or disc drive can

impair the image quality. In the worst case, neither video or

audio will be played back. To obtain optimum picture quality,

the Player should be checked (cleaning and replacement of

some parts) every 1,000 hours. Note that this period varies

depending on the environment (temperature, humidity, dust,

etc.) in which the Player is used. Contact your authorized

Sharp supplier for details.

Apparatus Claims of U.S. Patent Nos. 4,631,603,

4,577,216, 4,819,098 and 4,907,093 licensed for

limited viewing uses only.

This product incorporates copyright protection

technology that is protected by method claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be authorized by Macrovision

Corporation, and is intended for home and other

limited viewing uses only unless otherwise authorized

by Macrovision Corporation Reverse engineering or

disassembly is prohibited.

Do not attempt to clean the pickup lens yourself.

- 4 -

INDEX

SAFETY INFORMATION ..................................................2

INDEX................................................................................4

FEATURES........................................................................5

PACKAGE CONTENTS....................................................6

PRECAUTIONS ................................................................7

DISC CARE.......................................................................8

DISC COMPATIBILITY CHART........................................9

REMOTE CONTROL UNIT.............................................10

FRONT & REAR PANEL/DISPLAY WINDOW ...............12

 FRONT PANEL ............................................................. 12

 REAR PANEL ............................................................... 12

 DISPLAY WINDOW........................................................ 13

CONNECTIONS..............................................................14

 VIDEO OUTPUT TERMINALS AND CONNECTIONS .............. 14

 AUDIO OUTPUT TERMINALS AND CONNECTIONS .............. 15

INITIAL SETTING ...........................................................16

 TV SETUP ................................................................ 16

 TV DISPLAY ...................................................................16

 TV TYPE ........................................................................16

 SCART OUT...................................................................16

 AUDIO SETUP.......................................................... 17

 AUDIO OUT....................................................................17

 DOWN MIX.....................................................................17

 DOLBY DIGITAL SETUP........................................... 17

 DUAL MONO..................................................................17

 DYNAMIC.......................................................................18

 AUDIO EFFECT SETUP........................................... 18

 AUDIO EFFECT .............................................................18

 LINEAR PCM SETUP ............................................... 18

 Linear PCM OUT............................................................18

 GENERAL SETUP.................................................... 19

 ANGLE MARK................................................................19

 OSD LANGUAGE...........................................................19

 CAPTIONS.....................................................................19

 SCREEN SAVER............................................................19

 PREFERENCES....................................................... 20

 AUDIO ........................................................................... 20

 SUBTITLE...................................................................... 20

 DISC MENU................................................................... 20

 PARENTAL.....................................................................20

 PASSWORD .................................................................. 21

 DEFAULTS..................................................................... 21

ON-SCREEN DISPLAY (OSD) ....................................... 22

 DVD OSD MODES ...................................................... 22

 AUDIO CD/VCD OSD MODES...................................... 22

BASIC OPERATION OF PLAYBACK ............................ 23

 START PLAYBACK....................................................... 23

 SKIP PLAYBACK.......................................................... 23

 STILL/PAUSE PLAYBACK............................................ 23

 FAST FORWARD/REVERSE SCAN......................... 24

 SLOW-MOTION PLAYBACK ........................................ 24

 STOP PLAYBACK ........................................................ 25

ADVANCED OPERATION OF PLAYBACK ................... 26

 REPEATED PLAYBACK ............................................... 26

 PROGRAM PLAYBACK ............................................... 26

 TITLE MENU (DVD ONLY) ......................................... 27

 DVD MENU (DVD ONLY) ........................................... 27

 MULTI-ANGLE PLAYBACK .......................................... 27

 CHANGING SUBTITLE DURING PLAYBACK .................... 28

 CHANGING AUDIO LANGUAGE DURING PLAYBACK...... 28

 DIRECT FUNCTION..................................................... 28

 VCD PLAYBACK CONTROL (PBC) .......................... 29

MP3 PLAYBACK ............................................................ 30

 MP3 COMPATIBLE FORMAT........................................... 30

 OPERATION METHOD ................................................... 30

ADDITIONAL INFORMATION........................................ 30

 GLOSSARY ..............................................................32

 REGION MANAGEMENT INFORMATION................ 32

 LICENSE ..................................................................32

 Dolby License ................................................................ 32

 DTS License .................................................................. 32

 WARNING................................................................. 32

 TROUBLE SHOOTING............................................. 33

 SPECIFICATION....................................................... 34

- 5 -

FEATURES

< Compatible With DVD, VCD, Audio CD, and

MP3 Media Format.

This DVD player can play a variety of disc media

including DVD Video, Video CD, Audio CD, and MP3

media format.

< Two SCART Terminals

This DVD player equipped with two SCART terminals

to offer the ability to connect with VCR to TV.

(Loop-Through Interface).

< 2 Channel Analog Audio Output

This DVD player offers one set of down mixed analog

audio output.

< Virtual 3D Surround Sound

This DVD player features the virtual 3D surround

sound effect through standard analog outputs.

< Coaxial Digital Audio Outputs

The DVD player features one coaxial digital audio

output. User selectable SPDIF/RAW and SPDIF/PCM

digital audio maximizes convenience when switching

between DVD and Audio CD playback.

< Dolby

Digital, DTS

, and MPEG Digital

Audio Output Support

This DVD player can send Dolby

Digital, DTS

, and

MPEG Digital audio data via its built-in digital audio

output to an external Dolby

Digital or DTS

or MPEG

Digital decoder.

< High Quality 96kHz/24bit Audio D/A

Converter

This DVD player features a 96KHz/24Bit D/A converter

for superior audio reproduction of encoded discs.

< 10-Bit 27Mhz D/A Video Converter

This DVD player’s 10-bit D/A converter is four times

more accurate than conventional 8-bit converters. The

result is artifact-free and crystal clear video image.

< Auto NTSC and PAL Video Disc

Conversion

This unit can play NTSC and PAL formats discs. This

DVD player can automatically convert either format to

match your TV set. For example, if your TV set is a

PAL system TV and you’re playing a NTSC format disc,

this DVD player will automatically convert the NTSC

format signal to PAL format signal to play on your TV.

< Video Zoom Support

The user selectable digital video zoom-out, zoom-in on

a specific portion of a video image.

< Multi-Speed Fast Forward/Reverse Scan

The digital fast forward/reverse scan function is

capable of scanning with different speeds.

< Multi-Speed Slow Motion Forward /

Reverse Scan

This DVD player offers perfect slow motion scans.

< Volume Control of Analog Audio Output

This DVD player can control the volume of analog

audio output from remote control.

< Auto Power Shut Down Function

This DVD player offers auto power shut down function.

When the player is not in use for 20 minutes, the player

will shut down automatically to save the power

consumption and prolong the life of DVD player.

- 6 -

PACKAGE CONTENTS

Please verify that the following items are included within the DVD carton. If items are missing, please contact your

retailer/supplier.

< DVD Player x1

< Remote Control Unit x1

< AAA Batteries x2

< SCART Cable x1

< Operation Manual x1

- 7 -

PRECAUTIONS

Please read the following carefully to get the best and safest performance from this DVD player

< Power Supply

Make sure to use the correct power outlet as rated on

the back of the DVD unit. (AC 220-240 V)

< Power Cord

? Do not put any heavy objects on top of the power cord

to avoid fires or electrical shocks caused by cord

damage.

? Unplug the power cord if the unit will not be used for a

long time.

< Unit Placement

? Do not place this unit in locations with:

ü Vibrations

ü High humidity

ü Poor ventilation

ü Direct sunlight

ü Extremely high or low temperatures

? This unit should be placed on a horizontal surface

only.

? Keep this unit away from television sets, radios,

computers and loudspeakers to avoid magnetic field

interference.

< Usage and Storage

? Do not remove the top cover to avoid possible

electric shock from touching the inside of this unit.

? Do not place any heavy objects on top of this unit.

< Condensation

? Condensation may result from moving the unit from a

cold place to a hot place. Please turn the power on

for 1 to 2 hours before using this unit if condensation

occurs.

< Unit Cleaning

? Clean the front panel and the body of the unit with a

dry soft cloth. Other areas can be cleaned using a

soft cloth moistened with a mild detergent. Do not

clean with evaporative solutions to avoid possible

damage to the unit.

- 8 -

DISC CARE

< Disc Usage

? Please hold all discs by their edges or the centre

opening as shown below. Do not touch the shiny

surface of the discs.

? Do not stick labels or tape on the discs, and do not

scratch or damage the discs.

? The disc spins at a high speed during playback. Do

not use damaged, cracked, or warped discs because

they could damage the unit.

< Disc Cleaning

? Fingerprints or dirt on disc surfaces can weaken the

light reflected from the disc and directly influence the

signal quality. The poorer the signal quality, the

poorer the playback performance. Keep the disc

clean by wiping it straight out from the centre with a

dry soft cloth.

? If the disc is very dirty, wipe with a moist soft cloth,

then follow with a dry soft cloth.

? Do not use record cleaning sprays, benzene,

thinner, anti-static electricity liquids, or any other

solvent. These may damage the disc surface.

< Disc Storage

? Please keep the discs in their original cases to avoid

bending the discs. Do not keep discs in locations

with high temperature, high humidity, or direct

sunshine. These conditions may also cause

damage to the discs.

? Carefully read all instructions on the disc label.

- 9 -

DISC COMPATIBILITY CHART

This DVD player can play the following types of discs:

Disc Type Dimension/Side/Layer Max. Playback Time (Storage Capacity)

DVD MPEG2 TYPE

12 cm (5’’) /single sided/single layer

12 cm (5’’) /single sided/double layer

12 cm (5’’) /double sided/single layer

12 cm (5’’) /double sided/double layer

133 min. (4.7 GB)

242 min. (8.5 GB)

266 min. (9.4 GB)

484 min. (17 GB)

DVD Video

8 cm (3’’) /single sided/single layer

8 cm (3’’) /single sided/double layer

8 cm (3’’) /double sided/single layer

8 cm (3’’) /double sided/double layer

41 min.

75 min.

82 min.

150 min.

VCD MPEG1 TYPE

12 cm (5’’)/single sided/single layer 74 min.

Video CD

8 cm (3’’)/single sided/single layer 20 min.

CD CD

12 cm (5’’)/single sided/single layer 74 min.

Audio CD

8 cm (3’’)/single sided/single layer 20 min.

Notes:

1. DVD and VCD Discs contain both video and audio and can support multiple audio tracks.

2. Audio CD: Discs have audio only.

3. Do not insert DVD-ROMs, CD-ROMs or Photo CDs in this DVD player.

4. This unit complies with VCD Version 1.1 and Version 2.0.

5. This unit is compatible with CD-R & CD-RW.

- 10 -

REMOTE CONTROL UNIT

To use the remote control unit to operate the DVD

player, insert two batteries (size AAA) making sure that the

+ and – ends of the batteries are matched to the +/– marks

printed inside the battery compartment. To use the remote

controller, please point the remote control unit at the

remote sensor on the DVD player.

Notes:

i Do not use different types of batteries together, or mix old and new

batteries.

i When the remote control unit does not function correctly or its

operation range reduces, please replace both batteries at the same

time.

i If the remote control unit will be not used for a long time, please

remove the batteries to avoid possible damage from battery

leakage or corrosion.

i Keep the remote controller away from extremely hot or humid

locations.

i Do not open the remote controller unit.

- 11 -

REMOTE CONTROL UNIT

1. OPEN/CLOSE

Opens or closes disc tray.

2. SETUP

Customizes DVD player settings. Refer to p.16.

3. AUDIO

During playback of a DVD disc with more than two

audio languages, this button changes the audio

language played. Refer to p.28.

4. ANGLE

If the DVD disc contains multiple view angles, this

button will change the viewing angle displayed by the

DVD player. Refer to p.27.

5. SUBTITLE

During playback of DVD discs with more than two

subtitle languages, this button toggles between

available subtitle languages. Refer to p.28.

6. VIRTUAL

To enable the virtual audio effect during playback.

Refer to p.18 (Audio Effect Setup).

7. MUTE

To mute the sound of playback.

8. VOCAL

To switch the output audio in MONO LEFT, MONO

RIGHT, and STEREO modes during DVD, VCD, and

Audio CD playback.

9. A-B REPEAT

Displays A-B REPEAT playback. Refer to p.26.

10. TITLE

Enters the title menu for DVD discs. Refer to p.27

11. 3

Used for navigation within a selection menu

12. VOL

Reduce the volume of analog audio output.

13. SLOW

Engages slow-motion forward/reverse playback.

Refer to p.24.

14. STILL/PAUSE

Still/Pause the playback and enters into step mode

where the video can be advanced frame by frame.

Refer to p.23.

15.

SKIP

Goes back to the previous chapter during play. Refer

to p.23.

16.

REV

Fast reverse scan during playback. Refer to p.24.

17. FWD

Fast forward scan during playback. Refer to p.24.

18. SKIP

Skips to the next chapter during playback. Refer to

p.23.

19. STOP

Stops playback. Refer to p.25.

20. DISPLAY

On-Screen display of the DVD player’s operational

status. Refer to p.22.

21. 6

Used for navigation within a selection menu.

22. VOL

Increase the volume of analog audio output.

23. ENT/PLAY

Confirms selection of an item in the menu or starts

playing the disc.

24. 4

Used for navigation within a selection menu.

25. 5

Used for navigation within a selection menu.

26. MENU

Some DVDs have complex submenus. This button

allows access to these submenus. Refer to p.27.

27. REPEAT

Shows repeat playback for one title, or all titles on the

disc. Refer to p.26.

28. DIRECT

Enables search mode by title/chapter and time. Refer

to p.28.

29. Digits

Used for direct selection of menu choices, audio tracks,

and other inputs such as time and password

30. ZOOM

Enters the zoom mode during playback.

31. PBC

The button turns on/off the Playback Control (PBC)

function during VCD playback. Refer to p.29.

32. PROGRAM

Displays program playback for VCD/Audio CD. Refer

to p.26.

33. OPERATE

Turns on/off the DVD player unit.

- 12 -

FRONT & REAR PANEL/DISPLAY WINDOW

< Front Panel

1. OPERATE Switch Button

Turns the unit’s power on and off.

2. OPEN/CLOSE Button

Opens or closes the disc tray.

3. Disc Tray

To place DVD, VCD, Audio CD, and MP3 discs on.

4. STOP Button

Stops playback.

5. PLAY Button

Plays the inserted disc.

6. STANDBY Indicator

LED Indicator of Standby mode.

7. Display Window

Displays operation information.

SKIP Button

Goes to the previous chapter/track during playback with

DVD/VCD/Audio CD. It functions as “Go to the previous page” in the

PBC menu with VCD discs.

REV Button

Reverse scan.

10. FWD

Button

Forward scan.

11. SKIP

Button

Goes to the next chapter/track during playback with

DVD/VCD/Audio CD. It functions as “Go to the next page” in the

PBC menu with VCD discs.

< Rear Panel

1. Composite Video Output Jack

2. S-Video Output Jack

3. R/L Audio Output Jacks

4. Coaxial Digital Audio Output Jack

5. AV1 (TV) (SCART1)

6. AV2 (SCART2)

- 13 -

< Display Window

1. Disc inside indicator

2. DTS

Digital Audio Indicator (See Fig. 1 below)

Indicates the disc played contains DTS

Digital audio

encoding.

3. Title/Track Number Indicator

Some DVDs contain multiple title pages. This indicator

displays the title number currently in use or track

number (Audio CD) currently playing.

4. Audio CD/VCD Indicator (See Fig. 2-3 below)

Identifies the inserted disc as Audio CD or Video CD.

5. Dolby

Digital Audio Indicator (See Fig. 4 below)

Indicates the played disc contains Dolby

Digital audio

encoding data.

6. DVD Indicator (See Fig. 4 below)

Identifies the inserted disc as a DVD disc.

7. PBC Indicator for VCD Disc (See Fig. 5 below)

Playback Control indicator.

8. MP3 Indicator (See Fig. 6 below)

Identifies the inserted disc as a MP3 disc.

9. Analog Audio Output Indicator

Indicates the audio sound output from analog audio

jacks.

10. Elapsed Playback Time/Remaining Playback Time

Indicator

Displays elapsed playback time and playback

remainder time.

DVD TITLE is being read.

The disc tray is open.

The disc tray is being closed.

The system is loading

information from the disc.

No disc is loaded.

Bad disc or Wrong region

disc is being loaded.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

- 14 -

CONNECTIONS

< Video Output Terminals and Connections

l Composite Video Output Terminal

Composite video output is the most commonly used

video connection in use today and is supported by

most televisions and A/V receivers. Composite video

is set to display without user setup.

l S-Video Output Terminal

You will want to use S-video output with televisions

or monitors equipped with an S-video input

whenever component video inputs are not available.

To activate the S-video output, you must set the DVD

player’s “TV SETUP PAGE”/ “SCART OUT” setting

to S-VIDEO (Refer to p.16).

NOTE:

i S-video cable is not included with this player.

l SCART Terminal

The SCART terminal can be connected to the TV set equipped with SCART connectors. The audio transmitted on the

SCART is stereo sound. Whenever the SCART terminal is used, you must set the DVD player’s “TV SETUP PAGE”/

“SCART OUT” setting to “RGB” (Refer to p.16).

NOTE:

i For selected TVs, when the TV set is at standby mode, power on the DVD player will automatically power on the TV and switch to the SCART

video input channel.

WARNING:

1. S-Video and SCART/RGB video cannot output signals simultaneously.

2. When DVD player is in POWER OFF status, the LOOP THROUGH function does not work

with RGB mode.

- 15 -

< Audio Output Terminals and Connections

l Down-Mixed Audio Output Terminals (L/R)

Use down-mixed (stereo) audio output terminals for

connection with your television or other non-Dolby

Digital A/V receivers or amplifiers. These terminals

provide down-mixed Dolby

Digital audio signals for

standard 2-channel playback.

l Coaxial Digital Audio Output Terminals

Use digital audio outputs for connection with an

external Dolby

Digital or DTS

decoder. To use the

coaxial output, you will need to purchase a coaxial

cable.

Note:

i Digital cable is not included with this player.

- 16 -

INITIAL SETTING

Press the SETUP button on the remote controller to set up

the initial setting. The On-Screen Display (OSD) will display

below:

< TV SETUP

There are three available items: They are TV DISPLAY, TV

TYPE, and SCART OUT.

l TV DISPLAY

? NORMAL/PS

4:3 Pan & Scan video output for a normal TV set

? NORMAL/LB

4:3 Letterbox video output for a normal TV set

? WIDE

16:9 Wide Screen video output for a wide screen TV

set

NOTES:

i Aspect ratios available for playback will be printed on the DVD

rear packaging.

i Some DVDs are recorded in the Cinema Wide format (16:9

aspect ratio), and some are recorded in the standard format (4:3

aspect ratio). Some DVD discs are recorded in both formats and

may have the Pan Scan feature available. The Pan Scan feature if

available will fill the entire screen in 4:3 TV screen. However, it will

cut some of the picture off at the two sides.

l TV TYPE

? MULTI

The DVD player will choose the correct system to

display the playback of inserted disc.

? NTSC

The DVD player will output in NTSC format regardless

of what format the disc was designed for.

? PAL

The DVD player will output in PAL format regardless of

what format the disc was designed for.

l SCART OUT

The SCART OUT terminal has three kinds of output

ways; they are COMPOSITE, RGB, and S-VIDEO. If

you are using S-video output, please set this setting to

“S-VIDEO”. If you are using SCART output, you can

choose one of these three kinds output ways, which

matches with your TV’s SCART input.

NOTES:

i SCART video output and S-Video output cannot be used

simultaneously.

i The changes of TV output can be made with the disc tray opened

status. Press the DISPLAY button on the remote control and the TV

output will be changing in turn as COMPOSITE ßà RGB ßà

S-VIDEO

- - TV SETUP PAGE - -

TV DISPLAY

TV TYPE MULTI

SCART OUT NTSC

PAL

MAIN PAGE

SET TV STANDARD

SETUP MENU - - MAIN PAGE

TV SETUP

AUDIO SETUP

DOLBY DIGITAL SETUP

AUDIO EFFECT SETUP

LPCM SETUP

GENERAL SETUP

PREFERENCES

EXIT SETUP

GOTO TV SETUP

- - TV SETUP PAGE - -

TV DISPLAY NORMAL/PS

TV TYPE NORMAL/LB

SCART OUT WIDE

MAIN PAGE

SET TV DISPLAY MODE

- - TV SETUP PAGE - -

TV DISPLAY

TV TYPE

SCART OUT COMPOSITE

RGB

MAIN PAGE S-VIDEO

SET TV OUTPUT

- 17 -

< AUDIO SETUP

There are two available items: They are AUDIO OUT and

DOWN MIX.

l AUDIO OUT

You can choose to send the player’s audio signals to an

external receiver using the following outputs:

? ANALOG:

Audio signals are sent using stereo (L/R) audio

terminals. Selecting this choice will disable the digital

audio outputs.

? BITSTREAM:

Set to this selection will output the raw bit stream

signal of Dolby

Digital or DTS from the coaxial jack.

In order to enjoy Dolby

Digital DTS discs, this unit’s

digital output jack must be connected to the

digital-input jack of a Dolby

Digital or DTS compatible

receiver or processor.

? D-PCM:

PCM stands for Pulse Code Modulation and is digital

audio. Connecting this unit to an amplifier with a

built-in D/A converter can play the same digital audio

format as on CDs. Additionally, 2-channel analog

audio will output from the audio output jacks of

amplifier.

NOTES:

i Analog and digital audio signals cannot output simultaneously.

i Do not play the Dolby

Digital or DTS

or MPEG audio sound tracks

on an audio component without having a built-in Dolby

Digital or

DTS or MPEG audio decoder. Otherwise, when you play the Dolby

Digital or DTS or MPEG audio sound track, a loud noise will come

out from the speakers, affecting your ears or causing the speakers

to be damaged.

i This player has a conversion function for converting Dolby

Digital

and MPEG audio into the LPCM format. This allows playback of

CDs with the regular playback system without the need for a special

converter.

l DOWN MIX

? Pro Logic

Please connect to a built-in Dolby Pro Logic receiver or

amplifier to enjoy the Dolby Pro Logic surround sound.

? STEREO

Down mixed Stereo L/R audio output.

< DOLBY DIGITAL SETUP

There are two available items: They are DUAL MONO and

DYNAMIC.

l DUAL MONO

There are four available modes: STEREO, L-MONO,

R-MONO, and MIX-MONO.

Audio output description

MODE LEFT SPEAKER RIGHT SPEAKER

STERO STEREO -L STEREO -R

L-MONO

L-MONO L-MONO

R-MONO

R-MONO R-MONO

MIX-MONO

L-MONO+R-MONO L-MONO+R-MONO

- - AUDIO SETUP PAGE - -

AUDIO OUT

DOWNMIX Pro Logic

STEREO

MAIN PAGE

SET DOWNMIX MODE

- - DOLBY DIGITAL SETUP - -

DUAL MONO STEREO

DYNAMIC L-MONO

R-MONO

MAIN PAGE MIX-MONO

DUAL MONO (1 + 1) SETUP

- - AUDIO SETUP PAGE - -

AUDIO OUT ANALOG

DOWNMIX BITSTREAM

D-PCM

MAIN PAGE

SELECT AUDIO OUTPUT

- 18 -

l DYNAMIC

“Dynamic Range” is the difference between the

maximum level and the minimum level of sounds.

Sounds on a movie originally designed for movie

theaters feature a very wide dynamic range, so

sometimes it is not suitable for home use. Depending

on the condition of your listening environment, Dynamic

Range function can reduce the instant sound effect

alteration of the movie while playing back. When seeing

movies in the night, turn this function on to avoid the

suddenly loud sound to influence your neighbors.

(Default value is FULL, no compression to be done.)

NOTES:

i This function works only during playback of Dolby

Digital recorded

discs.

i The level of Dynamic Range Reduction may differ depending on

the DVD discs.

< AUDIO EFFECT SETUP

l AUDIO EFFECT

This player offers the audio effect function. This function

is available when setting to “ON” position and then

press the VIRTUAL button on the remote control to open

this function during playing back. There are four steps

of effect level.

< LINEAR PCM SETUP

This option sets the audio output format sent using the

unit’s coaxial digital audio output.

l Linear PCM OUT

? LPCM 48K

In the Linear PCM setting, “48K” means “the digital

audio output maximum sampling rate is 48KHz”;

therefore, when the title’s encoding sampling rate* is

96KHz, the output will be forced converted to 48KHz.

? LPCM 96K

If “96K” is selected, then the maximum output

sampling rate is 96KHz and no conversion will take

place.

DISC CODING AND OUTPUT FORMAT

Disc

Audio encoding format

Digital output format

Dolby

Digital

Dolby

Digital Bit stream

(1~5.1 ch) or 48kHz/16bits

2ch Linear PCM

DTS

Bit stream (1~5.1 ch) or OFF

Linear PCM

(48/96kHz, 24bits)

Linear PCM

(48KHz/16 bits up to

96kHz/24bits)

DVD

MPEG

PCM (2ch) (48KHz/16 bit) or

MPEG audio bit stream (1-7.1 ch)

Video

MPEG I Linear PCM (44.1KHz sampling)

Audio

Linear PCM Linear PCM (44.1kHz/16bit)

NOTES:

i Sampling rate:

When a sound wave is converted to a digital signal, the sound is

sampled and converted to data at a specific frequency rate. For

example, a signal with a 96 kHz sampling rate indicates that in one

second, the analog signal was sampled 96000 times to produce

the digital signal.

i In LPCM set-up menu, there will be a case that even when “LPCM

96K” is selected, output signal is converted to 48KHz if the disc has

the copy guard management system in it.

- - LPCM SETUP PAGE - -

LPCM OUT LPCM 48K

LPCM 96K

MAIN PAGE

SET LPCM OUTPUT TO 48K OR 96K

- - AUDIO EFFECT PAGE - -

AUDIO EFFECT

OFF

MAIN PAGE

SET AUDIO EFFECT MODE

- - DOLBY DIGITAL SETUP - -

DUAL MONO

DYNAMIC

MAIN PAGE

DYNAMIC RANGE COMPRESSION

FULL

6/8

4/8

2/8

OFF

- 19 -

< GENERAL SETUP

There are four available selections: ANGLE MARK, OSD

LANG, CAPTIONS, and SCR SAVER.

l ANGLE MARK

During playback of a title with multiple angle sections,

the message " " will appear on the upper corner of

the screen.

? When ANGLE MARK is set to "ON", the angle mark

OSD will stay on the screen until the end of the

playback title or chapter.

? When ANGLE MARK is set to "OFF", the angle mark

OSD will stay on the screen for 3 sec and then

disappear.

l OSD LANGUAGE

You can select the language for the setup menu or the

operation message display. There are six available

OSD languages: ENGLISH, FRENCH, SPANISH,

ITALIAN, SWEDISH and GERMAN for display.

l CAPTIONS

Closed Caption (CC) is a standardized method of

encoding text into an NTSC television signal. A TV can

display the text with a built-in decoder. Closed Caption

can be carried on DVD. If a DVD title contains a CC

mark on the rear of the box, then you can set Captions

to “ON” and read written captions on the TV screen.

Default is set to “OFF”.

l SCREEN SAVER

When this DVD player is idle (after about 5 minutes of

inactivity), the screen saver can be activated to prolong

the TV monitor’s life.

NOTES:

i Caution: The DVD player can hold a still video image or OSD image

on your television screen indefinitely. If you leave the still video

image or OSD image displayed on your TV for a very long time. It

may cause the permanent damage to your TV screen.

- - GENERAL PAGE - -

ANGLE MARK

OSD LANG

CAPTIONS ON

SCR SAVER OFF

MAIN PAGE

CLOSED CAPTION

- - GENERAL PAGE - -

ANGLE MARK

OSD LANG OFF

CAPTIONS

SCR SAVER

MAIN PAGE

ANGLE MARK ON/OFF

- - GENERAL PAGE - -

ANGLE MARK

OSD LANG

CAPTIONS

SCR SAVER ON

OFF

MAIN PAGE

SCREEN SAVER

- - GENERAL PAGE - -

ANGLE MARK

OSD LANG ENGLISH

CAPTIONS FRENCH

SCR SAVER ITALIAN

GERMAN

MAIN PAGE SWEDISH

SPANISH

SET OSD LANGUAGE

- 20 -

< PREFERENCES

Preferences allow you to set the default AUDIO, SUBTITLE,

DISC MENU, PARENTAL, PASSWORD, and factory

DEFAULTS of this player. This setting is only available

when the DVD player is in the STOP mode by pressing the

STOP button twice.

NOTES

i Pressing the STOP button once only pause the playback. You must

press the STOP button twice to stop the playback.

l AUDIO

This unit supports six audio selections, as shown below,

for your preferred audio setting.

l SUBTITLE

This unit supports six subtitle selections, as shown

below, for your preferred default subtitle setting. When

“OFF” is selected, there will be no subtitle is displayed

during playback.

l DISC MENU

This unit supports six DISC MENU languages.

l PARENTAL

Functions to limit the playback of some discs that

contain mature scenes. The limitation varies from disc

to disc; when it is activated, playback is completely

prohibited. There are eight levels of parental setting of

this unit.

When you want to change the parental rating level, you

will be asked to enter a password.

NOTES:

i Use “3308” to override the forgotten password and re-enter a new

password.

- - PREFERENCES PAGE - -

AUDIO

SUBTITLE

DISC MENU ENGLISH

PARENTAL FRENCH

PASSWORD ITALIAN

DEFAULTS GERMAN

SWEDISH

MAIN PAGE SPANISH

PREFERRED MENU LANGUAGE

- - PREFERENCES PAGE - -

AUDIO 1

SUBTITLE 2

DISC MENU 3

PARENTAL 4

PASSWORD 5

DEFAULTS 6

MAIN PAGE 8 ADULT

OFF

SET PARENTRAL CONTROL

- - PREFERENCES PAGE - -

AUDIO ENGLISH

SUBTITLE FRENCH

DISC MENU ITALIAN

PARENTAL GERMAN

PASSWORD SWEDISH

DEFAULTS SPANISH

MAIN PAGE

PREFERRED AUDIO LANGUAGE

- - PREFERENCES PAGE - -

AUDIO

SUBTITLE ENGLISH

DISC MENU FRENCH

PARENTAL ITALIAN

PASSWORD GERMAN

DEFAULTS SWEDISH

SPANISH

MAIN PAGE OFF

PREFERRED SUBTITLE LANGUAGE

PASSWORD VERIFY PAGE

INPUT PASSWORD:

PLEASE ENTER PASSWORD

- 21 -

l PASSWORD

The password is a 4-digit number. When you want to

change the password, select “CHANGE” as shown

below.

You will be asked to enter the old password, then enter the

new password, and confirm it.

NOTES:

i The default password number is”3308”.

l DEFAULTS

When you select “RESET”, all the initial settings will be

restored to the default setting.

- - PREFERENCES PAGE - -

AUDIO

SUBTITLE

DISC MENU

PARENTAL

PASSWORD CHANGE

DEFAULTS

MAIN PAGE

CHANGE PASSWORD

PASSWORD CHANGE PAGE

OLD PASSWORD:

NEW PASSWORD:

CONFIRM PWD:

PLEASE ENTER OLD PASSWORD

- - PREFERENCES PAGE - -

AUDIO

SUBTITLE

DISC MENU

PARENTAL

PASSWORD

DEFAULTS RESET

MAIN PAGE

LOAD FACTORY SETTINGS

- 22 -

ON-SCREEN DISPLAY (OSD)

< DVD OSD Modes

There are two OSD display modes available when playing

a DVD disc.

l Mode 1

Shows the status of the pressed button and some special

messages are displayed on the screen. For example,

when the OPEN/CLOSE button is pressed, the OSD shows:

l Mode 2

Shows the playback information of a movie or title.

? When pressing the DISPLAY button on R/C, the

information OSD will display on the screen in the

sequence as shown below:

time 2

time

time 4

time

? When pressing the DISPLAY button on the remote

control again, it will turn off the OSD.

< Audio CD/VCD OSD Modes

There are two OSD display modes available when playing

a VCD, and Audio CD disc.

l Mode 1

Shows the status of the pressed button and some special

messages are displayed on the screen as previous

description.

l Mode 2

Shows the playback time information of a disc.

PBC ON (VCD 2.0 above only):

? When pressing the DISPLAY button on R/C, the

information OSD will display on the screen in the

sequence as shown below:

1. SINGLE ELAPSED 2. SINGLE REMAIN

PBC OFF or Audio CD playback:

1. SINGLE ELAPSED 2. SINGLE REMAIN

3. TOTAL ELAPSED 4. TOTAL REMAIN

? When pressing the DISPLAY button on the remote

control again, it will turn off the OSD.

³OPEN

TITLE 002/04 CHAPTER 001/009