469870
15
Verklein
Vergroot
Pagina terug
1/45
Pagina verder
MODEL
XG-C465X
XG-C435X
DATA PROJECTOR
SETUP MANUAL
Setting up the Screen.......................................... 2
Screen Size and Projection Distance ................ 3
Throw Distance ....................................................... 3
Standard Zoom Lens .............................................. 4
Wide-zoom Lens (AN-C12MZ) ............................... 5
Tele-zoom Lens (AN-C18MZ) ................................. 6
Tele-zoom Lens (AN-C27MZ) ................................. 7
Tele-zoom Lens (AN-C41MZ) ................................. 8
Changing the Lens .............................................. 9
Connecting Pin Assignments .......................... 11
RS-232C Specifications and Commands ........ 13
Computer control .................................................. 13
Communication conditions ................................... 13
Basic format .......................................................... 13
Commands ........................................................... 14
Setting up the Projector Network Environment ...
18
Network settings on the computer ....................... 18
1. Connecting the Projector to a Computer.......... 19
2. Setting an IP Address for the Computer .......... 20
3.
Setting up a Network Connection for the Projector ....
22
Controlling the Projector via LAN.................... 24
Controlling the Projector Using Internet Explorer
(Version 5.0 or later) ................................... 24
Confirming the Projector Status (Status) ............. 25
Controlling the Projector (Control) ....................... 25
Setting and Adjusting the Projector
(Settings & Adjustments)............................ 26
Setting the Security (Network – Security) ............ 26
Making General Settings for the Network
(Network - General) .................................... 27
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings) ........................ 27
Setting Error Items and Destination Addresses
to which E-mail is to be Sent when an
Error Occurs (Mail – Recipient Settings) ... 28
Setting Error Items and the URL that are to be
Displayed when an Error Occurs
(Service & Support – Access URL) ........... 28
Setting up the Projector Using RS-232C or Telnet ....
29
When Connecting Using RS-232C ....................... 29
When Connecting Using Telnet ............................ 30
SETUP MENU (Main Menu) ................................. 31
ADVANCED SETUP MENU ................................. 31
View Setting Detail List ([V]View All Setting) ....... 32
Set Items ............................................................... 32
Save Settings and Quit ([S]Save & Quit) ............. 33
Quit without Saving Settings ([Q]Quit Unchanged) ..
33
IP Address Setting ([1]IP Address) ...................... 34
Subnet Mask Setting ([2]Subnet Mask) ............... 34
Default Gateway Setting ([3]Default Gateway) .... 34
User Name Setting ([4]User Name) ..................... 34
Password Setting ([5]Password) .......................... 35
RS-232C Baud Rate Setting
([6]RS-232C Baud Rate) ............................ 35
Projector Name Setting ([7]Projector Name) ....... 35
DHCP Client Setting ([8]DHCP Client)................. 35
Disconnecting All Connections
([D]Disconnect All) ..................................... 36
Entering ADVANCED SETUP MENU
([A]Advanced Setup) .................................. 36
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time) ............. 36
Data Port Setting (ADVANCED[2]Data Port) ....... 36
Carrying out Network Ping Test
(ADVANCED[5]Network Ping Test) ............ 37
Setting of Accept IP Address (ADVANCED[6]Accept
IP Addr(1) – [8]Accept IP Addr(3)) .................
37
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr) ............ 37
Setting of Search Port
(ADVANCED[0]Search Port) ...................... 38
Return to Default Settings
(ADVANCED[!]Restore Default Setting) ..... 38
Return to Main Menu
(ADVANCED[Q]Return to Main Menu)....... 38
Resetting the Lamp Timer of the Projector
via LAN ....................................................... 39
Troubleshooting ................................................. 41
Dimensions ........................................................ 44
-2
Example of standard setup
H
Screen
L: Projection distance
Lens center
Base line:
Horizontal line passing through
the lens center
Side View
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat
and level. Doing so will eliminate the need for Keystone correction and provide the best image quality.
Note
The projector lens should be centered in the middle of the screen. If the horizontal line passing through the
lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly
on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when
setting up the screen in a sunny or bright room.
Standard Setup (Front Projection)
Place the projector at the required distance from
the screen according to the desired picture size.
Setting up the Screen
The distance from the screen to the projector may vary depending on the size of the
screen.
The default setting can be used, when placing the projector in front of the screen. If the pro-
jected image is reversed, readjust the setting to “Front” in the “PRJ Mode” menu. (See page
52
of the projector’s operation manual.)
Place the projector so that an imaginary horizontal line that passes through the center of the
lens is perpendicular to the screen.
-3
Screen Size and Projection Distance
The projection screen size varies according to the distance from the lens of the projector to the screen.
The optional lenses from Sharp are also available for specialized application. Please see your nearest Sharp
Authorized Projector Dealer to details on all the lenses. (Refer to the lens operation manual when using a
lens.)
Install the projector so that projected images are projected onto the screen at the optimum size by referring
to the table. Use the values in the table as a reference when installing the projector.
Throw Distance
The graph below is for 100 inches (254 cm) screen with 4:3 normal mode.
Screen
10 20 30 5040 (ft)
3.0 6.0 9.1 15.212.2 (m)
Standard zoom lens
11'9"–14'1" (3.6 m–4.3 m)
Throw distance ratio 1:1.8–2.1
Tele-zoom lens (AN-C18MZ)
14'10"–18'10" (4.5 m–5.7 m)
Throw distance ratio 1:2.2–2.8
Tele-zoom lens (AN-C27MZ)
22'–33'11" (6.7 m–10.3 m)
Throw distance ratio 1:3.3–5.1
Tele-zoom lens (AN-C41MZ)
34'5"–48'4" (10.5 m–14.7 m)
Throw distance ratio 1:5.2–7.2
Wide-zoom lens (AN-C12MZ)
9'11"–12'5" (3.0 m–3.8 m)
Throw distance ratio 1:1.5–1.9
-4
Standard Zoom Lens
F1.7-F1.9, f=28.0-33.6 mm
NORMAL Mode (4:3)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.03571
χ
L2 (m) = 0.04286
χ
H (cm) = –0.1524
χ
[Feet/inches]
L1 (ft) = 0.03571
χ
/ 0.3048
L2 (ft) = 0.04286
χ
/ 0.3048
H (in) = –0.1524
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.0389
χ
L2 (m) = 0.04669
χ
H (cm) = 0.04151
χ
S (cm) = ±0.20754
χ
[Feet/inches]
L1 (ft) = 0.0389
χ
/ 0.3048
L2 (ft) = 0.04669
χ
/ 0.3048
H (in) = 0.04151
χ
/ 2.54
S (in) = ±0.20754
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
S: Adjustable range of image position (cm/in)
STRETCH Mode (16:9)
Screen Size and Projection Distance
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
500'' (1270 cm) 1016 cm (400'') 762 cm (300'') 17.9 m(58' 7") 21.4 m (70' 4") –76 cm (–30")
300'' (762 cm) 610 cm (240'') 457 cm (180'') 10.7 m (35' 2") 12.9 m (42' 2") –46 cm (–18")
270'' (686 cm) 549 cm (216'') 411 cm (162'') 9.6 m (31' 8") 11.6 m (38') –41 cm (–16
13
/64")
250'' (635 cm) 508 cm (200'') 381 cm (150'') 8.9 m (29' 3") 10.7 m (35' 2") –38 cm (–15")
200'' (508 cm) 406 cm (160'') 305 cm (120'') 7.1 m (23' 5") 8.6 m (28' 1") –30 cm (–12")
150'' (381 cm) 305 cm (120'') 229 cm (90'') 5.4 m (17' 7") 6.4 m (21' 1") –23 cm (–9")
100'' (254 cm) 203 cm (80'') 152 cm (60'') 3.6 m (11' 9") 4.3 m (14' 1") –15 cm (–6")
84'' (213 cm) 171 cm (67'') 128 cm (50'') 3.0 m (9' 10") 3.6 m (11' 10") –13 cm (–5
3
/64")
80'' (203 cm) 163 cm (64'') 122 cm (48'') 2.9 m (9' 4") 3.4 m (11' 3") –12 cm (–4
51
/64")
72'' (183 cm) 146 cm (58'') 110 cm (43'') 2.6 m (8' 5") 3.1 m (10' 1") –11 cm (–4
5
/16")
60'' (152 cm) 122 cm (48'') 91 cm (36'') 2.1 m (7') 2.6 m (8' 5") –9 cm (–3
19
/32")
40'' (102 cm) 81 cm (32'') 61 cm (24'') 1.4 m (4' 8") 1.7 m (5' 7") –6 cm (–2
13
/32")
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
Adjustable range of
image position [S]
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
450'' (1143 cm) 996 cm (392'') 560 cm (221'') 17.5 m(57' 5") 21.0 m (68' 11") 19 cm (7
23
/64") ±93 cm (±36
49
/64")
300'' (762 cm) 664 cm (261'') 374 cm (147'') 11.7 m (38' 3") 14.0 m (45' 11") 12 cm (4
29
/32") ±62 cm (±24
33
/64")
250'' (635 cm) 553 cm (218'') 311 cm (123'') 9.7 m (31' 11") 11.7 m (38' 4") 10 cm (4
5
/64") ±52 cm (±20
27
/64")
225'' (572 cm) 498 cm (196'') 280 cm (110'') 8.8 m (28' 9") 10.5 m (34' 6") 9 cm (3
43
/64") ±47 cm (±18
25
/64")
200'' (508 cm) 443 cm (174'') 249 cm (98'') 7.8 m (25' 6") 9.3 m (30' 8") 8 cm (3
17
/64") ±42 cm (±16
11
/32")
150'' (381 cm) 332 cm (131'') 187 cm (74'') 5.8 m (19' 2") 7.0 m (23') 6 cm (2
29
/64") ±31 cm (±12
1
/4")
133'' (338 cm) 294 cm (116'') 166 cm (65'') 5.2 m (17') 6.2 m (20' 4") 6 cm (2
11
/64") ±28 cm (±10
7
/8")
106'' (269 cm) 235 cm (92'') 132 cm (52'') 4.1 m (13' 6") 4.9 m (16' 3") 4 cm (1
47
/64") ±22 cm (±8
21
/32")
100'' (254 cm) 221 cm (87'') 125 cm (49'') 3.9 m (12' 9") 4.7 m (15' 4") 4 cm (1
41
/64") ±21 cm (±8
11
/64")
92'' (234 cm) 204 cm (80'') 115 cm (45'') 3.6 m (11' 9") 4.3 m (14' 1") 4 cm (1
1
/2") ±19 cm (±7
33
/64")
84'' (213 cm) 186 cm (73'') 105 cm (41'') 3.3 m (10' 9") 3.9 m (12' 10") 3 cm (1
3
/8") ±17 cm (±6
55
/64")
80'' (203 cm) 177 cm (70'') 100 cm (39'') 3.1 m (10' 3") 3.7 m (12' 3") 3 cm (1
5
/16") ±17 cm (±6
17
/32")
72'' (183 cm) 159 cm (63'') 90 cm (35'') 2.8 m (9' 2") 3.4 m (11') 3 cm (1
11
/64") ±15 cm (±5
57
/64")
60'' (152 cm) 133 cm (52'') 75 cm (29'') 2.3 m (7' 8") 2.8 m (9' 2") 2 cm (
63
/64") ±12 cm (±4
29
/32")
40'' (102 cm) 89 cm (35'') 50 cm (20'') 1.6 m (5' 1") 1.9 m (6' 2") 2 cm (
21
/32") ±8 cm (±3
17
/64")
Note
Allow a margin of error in the value in the diagrams above.
When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates
that the bottom of the image is below the lens center.
-5
Wide-zoom Lens (AN-C12MZ)
F2.2-F2.7, f=24.5-30.7 mm
NORMAL Mode (4:3)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.03019
χ
L2 (m) = 0.03783
χ
H (cm) = –0.1524
χ
[Feet/inches]
L1 (ft) = 0.03019
χ
/ 0.3048
L2 (ft) = 0.03783
χ
/ 0.3048
H (in) = –0.1524
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
Note
Allow a margin of error in the value in the diagrams above.
When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates
that the bottom of the image is below the lens center.
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.03289
χ
L2 (m) = 0.04121
χ
H (cm) = 0.04151
χ
S (cm) = ±0.20754
χ
[Feet/inches]
L1 (ft) = 0.03289
χ
/ 0.3048
L2 (ft) = 0.04121
χ
/ 0.3048
H (in) = 0.04151
χ
/ 2.54
S (in) = ±0.20754
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
S: Adjustable range of image position (cm/in)
STRETCH Mode (16:9)
Screen Size and Projection Distance
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
250'' (635 cm) 508 cm (200'') 381 cm (150'') 7.5 m (24' 9") 9.5 m (31') –38 cm (–15")
200'' (508 cm) 406 cm (160'') 305 cm (120'') 6.0 m (19' 10") 7.6 m (24' 10") –30 cm (–12")
150'' (381 cm) 305 cm (120'') 229 cm (90'') 4.5 m (14' 10") 5.7 m (18' 7") –23 cm (–9")
100'' (254 cm) 203 cm (80'') 152 cm (60'') 3.0 m (9' 11") 3.8 m (12' 5") –15 cm (–6")
84'' (213 cm) 171 cm (67'') 128 cm (50'') 2.5 m (8' 4") 3.2 m (10' 5") –13 cm (–5
3
/64")
80'' (203 cm) 163 cm (64'') 122 cm (48'') 2.4 m (7' 11") 3.0 m (9' 11") –12 cm (–4
51
/64")
72'' (183 cm) 146 cm (58'') 110 cm (43'') 2.2 m (7' 2") 2.7 m (8' 11") –11 cm (–4
5
/16")
60'' (152 cm) 122 cm (48'') 91 cm (36'') 1.8 m (5' 11") 2.3 m (7' 5") 9 cm (–3
19
/32")
40'' (102 cm) 81 cm (32'') 61 cm (24'') 1.2 m (4') 1.5 m (5') –6 cm (–2
13
/32")
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
Adjustable range of
image position [S]
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
225'' (572 cm) 498 cm (196'') 280 cm (110'') 7.4 m (24' 3") 9.3 m (30' 5") 9 cm (3
43
/64") ±47 cm (±18
25
/64")
200'' (508 cm) 443 cm (174'') 249 cm (98'') 6.6 m (21' 7") 8.2 m (27') 8 cm (3
17
/64") ±42 cm (±16
11
/32")
150'' (381 cm) 332 cm (131'') 187 cm (74'') 4.9 m (16' 2") 6.2 m (20' 3") 6 cm (2
29
/64") ±31 cm (±12
1
/4")
133'' (338 cm) 294 cm (116'') 166 cm (65'') 4.4 m (14' 4") 5.5 m (18') 6 cm (2
11
/64") ±28 cm (±10
7
/8")
106'' (269 cm) 235 cm (92'') 132 cm (52'') 3.5 m (11' 5") 4.4 m (14' 4") 4 cm (1
47
/64") ±22 cm (±8
21
/32")
100'' (254 cm) 221 cm (87'') 125 cm (49'') 3.3 m (10' 9") 4.1 m (13' 6") 4 cm (1
41
/64") ±21 cm (±8
11
/64")
92'' (234 cm) 204 cm (80'') 115 cm (45'') 3.0 m (9' 11") 3.8 m (12' 5") 4 cm (1
1
/2") ±19 cm (±7
33
/64")
84'' (213 cm) 186 cm (73'') 105 cm (41'') 2.8 m (9' 1") 3.5 m (11' 4") 3 cm (1
3
/8") ±17 cm (±6
55
/64")
80'' (203 cm) 177 cm (70'') 100 cm (39'') 2.6 m (8' 8") 3.3 m (10' 10") 3 cm (1
5
/16") ±17 cm (±6
17
/32")
72'' (183 cm) 159 cm (63'') 90 cm (35'') 2.4 m (7' 9") 3.0 m (9' 9") 3 cm (1
11
/64") ±15 cm (±5
57
/64")
60'' (152 cm) 133 cm (52'') 75 cm (29'') 2.0 m (6' 6") 2.5 m (8' 1") 2 cm (
63
/64") ±12 cm (±4
29
/32")
40'' (102 cm) 89 cm (35'') 50 cm (20'') 1.3 m (4' 4") 1.6 m (5' 5") 2 cm (
21
/32") ±8 cm (±3
17
/64")
-6
Tele-zoom Lens (AN-C18MZ)
F1.7-F2.2, f=36.5-46.3 mm
NORMAL Mode (4:3)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.04529
χ
L2 (m) = 0.05745
χ
H1 (cm) = –0.1524
χ
[Feet/inches]
L1 (ft) = 0.04529
χ
/ 0.3048
L2 (ft) = 0.05745
χ
/ 0.3048
H (in) =
0.1524
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
Note
Allow a margin of error in the value in the diagrams above.
When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates
that the bottom of the image is below the lens center.
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.04934
χ
L2 (m) = 0.06259
χ
H (cm) = 0.04151
χ
S (cm) = ±0.20754
χ
[Feet/inches]
L1 (ft) = 0.04934
χ
/ 0.3048
L2 (ft) = 0.06259
χ
/ 0.3048
H1 (in) = 0.04151
χ
/ 2.54
S (in) = ±0.20754
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
S: Adjustable range of image position (cm/in)
STRETCH Mode (16:9)
Screen Size and Projection Distance
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
250'' (635 cm) 508 cm (200'') 381 cm (150'') 11.3 m (37' 2") 14.4 m (47' 1") –38 cm (–15")
200'' (508 cm) 406 cm (160'') 305 cm (120'') 9.1 m (29' 9") 11.5 m (37' 8") –30 cm (–12")
150'' (381 cm) 305 cm (120'') 229 cm (90'') 6.8 m (22' 3") 8.6 m (28' 3") –23 cm (–9")
100'' (254 cm) 203 cm (80'') 152 cm (60'') 4.5 m (14' 10") 5.7 m (18' 10") –15 cm (–6")
84'' (213 cm) 171 cm (67'') 128 cm (50'') 3.8 m (12' 6") 4.8 m (15' 10") –13 cm (–5
3
/64")
80'' (203 cm) 163 cm (64'') 122 cm (48'') 3.6 m (11' 11") 4.6 m (15' 1") –12 cm (–4
51
/64")
72'' (183 cm) 146 cm (58'') 110 cm (43'') 3.3 m (10' 8") 4.1 m (13' 7") –11 cm (–4
5
/16")
60'' (152 cm) 122 cm (48'') 91 cm (36'') 2.7 m (8' 11") 3.4 m (11' 4") –9 cm (–3
19
/32")
40'' (102 cm) 81 cm (32'') 61 cm (24'') 1.8 m (5' 11") 2.3 m (7' 6") –6 cm (–2
13
/32")
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
Adjustable range of
image position [S]
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
225'' (572 cm) 498 cm (196'') 280 cm (110'') 11.1 m (36' 5") 14.1 m (46' 2") 9 cm (3
43
/64") ±47 cm (±18
25
/64")
200'' (508 cm) 443 cm (174'') 249 cm (98'') 9.9 m (32' 5") 12.5 m (41' 1") 8 cm (3
17
/64") ±42 cm (±16
11
/32")
150'' (381 cm) 332 cm (131'') 187 cm (74'') 7.4 m (24' 3") 9.4 m (30' 10") 6 cm (2
29
/64") ±31 cm (±12
1
/4")
133'' (338 cm) 294 cm (116'') 166 cm (65'') 6.6 m (21' 6") 8.3 m (27' 4") 6 cm (2
11
/64") ±28 cm (±10
7
/8")
106'' (269 cm) 235 cm (92'') 132 cm (52'') 5.2 m (17' 2") 6.6 m (21' 9") 4 cm (1
47
/64") ±22 cm (±8
21
/32")
100'' (254 cm) 221 cm (87'') 125 cm (49'') 4.9 m (16' 2") 6.3 m (20' 6") 4 cm (1
41
/64") ±21 cm (±8
11
/64")
92'' (234 cm) 204 cm (80'') 115 cm (45'') 4.5 m (14' 11") 5.8 m (18' 11") 4 cm (1
1
/2") ±19 cm (±7
33
/64")
84'' (213 cm) 186 cm (73'') 105 cm (41'') 4.1 m (13' 7") 5.3 m (17' 3") 3 cm (1
3
/8") ±17 cm (±6
55
/64")
80'' (203 cm) 177 cm (70'') 100 cm (39'') 3.9 m (12' 11") 5.0 m (16' 5") 3 cm (1
5
/16") ±17 cm (±6
17
/32")
72'' (183 cm) 159 cm (63'') 90 cm (35'') 3.6 m (11' 8") 4.5 m (14' 9") 3 cm (1
11
/64") ±15 cm (±5
57
/64")
60'' (152 cm) 133 cm (52'') 75 cm (29'') 3.0 m (9' 9") 3.8 m (12' 4") 2 cm (
63
/64") ±12 cm (±4
29
/32")
40'' (102 cm) 89 cm (35'') 50 cm (20'') 2.0 m (6' 6") 2.5 m (8' 3") 2 cm (
21
/32") ±8 cm (±3
17
/64")
-7
Tele-zoom Lens (AN-C27MZ)
F2.0-F2.8, f=53.8-82.9 mm
NORMAL Mode (4:3)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.0671
χ
L2 (m) = 0.10348
χ
H (cm) = –0.1524
χ
[Feet/inches]
L1 (ft) = 0.0671
χ
/ 0.3048
L2 (ft) = 0.10348
χ
/ 0.3048
H (in) = –0.1524
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.0731
χ
L2 (m) = 0.11274
χ
H (cm) = 0.04151
χ
S (cm) = ±0.20754
χ
[Feet/inches]
L1 (ft) = 0.0731
χ
/ 0.3048
L2 (ft) = 0.11274
χ
/ 0.3048
H (in) = 0.04151
χ
/ 2.54
S (in) = ±0.20754
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
S: Adjustable range of image position (cm/in)
STRETCH Mode (16:9)
Screen Size and Projection Distance
Note
Allow a margin of error in the value in the diagrams above.
When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates
that the bottom of the image is below the lens center.
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
250'' (635 cm) 508 cm (200'') 381 cm (150'') 16.8 m (55') 25.9 m (84' 11") –38 cm (–15")
200'' (508 cm) 406 cm (160'') 305 cm (120'') 13.4 m (44') 20.7 m (67' 11") –30 cm (–12")
150'' (381 cm) 305 cm (120'') 229 cm (90'') 10.1 m (33') 15.5 m (50' 11") –23 cm (–9")
100'' (254 cm) 203 cm (80'') 152 cm (60'') 6.7 m (22') 10.3 m (33' 11") –15 cm (–6")
84'' (213 cm) 171 cm (67'') 128 cm (50'') 5.6 m (18' 6") 8.7 m (28' 6") –13 cm (–5
3
/64")
80'' (203 cm) 163 cm (64'') 122 cm (48'') 5.4 m (17' 7") 8.3 m (27' 2") –12 cm (–4
51
/64")
72'' (183 cm) 146 cm (58'') 110 cm (43'') 4.8 m (15' 10") 7.5 m (24' 5") –11 cm (–4
5
/16")
60'' (152 cm) 122 cm (48'') 91 cm (36'') 4.0 m (13' 3") 6.2 m (20' 4") –9 cm (–3
19
/32")
40'' (102 cm) 81 cm (32'') 61 cm (24'') 2.7 m (8' 10") 4.1 m (13' 7") 6 cm (–2
13
/32")
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
Adjustable range of
image position [S]
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
225'' (572 cm) 498 cm (196'') 280 cm (110'') 16.4 m (54') 25.4 m (83' 3") 9 cm (3
43
/64") ±47 cm (±18
25
/64")
200'' (508 cm) 443 cm (174'') 249 cm (98'') 14.6 m (48') 22.5 m (74') 8 cm (3
17
/64") ±42 cm (±16
11
/32")
150'' (381 cm) 332 cm (131'') 187 cm (74'') 11.0 m (36') 16.9 m (55' 6") 6 cm (2
29
/64") ±31 cm (±12
1
/4")
133'' (338 cm) 294 cm (116'') 166 cm (65'') 9.7 m (31' 11") 15.0 m (49' 2") 6 cm (2
11
/64") ±28 cm (±10
7
/8")
106'' (269 cm) 235 cm (92'') 132 cm (52'') 7.7 m (25' 5") 12.0 m (39' 2") 4 cm (1
47
/64") ±22 cm (±8
21
/32")
100'' (254 cm) 221 cm (87'') 125 cm (49'') 7.3 m (24') 11.3 m (37') 4 cm (1
41
/64") ±21 cm (±8
11
/64")
92'' (234 cm) 204 cm (80'') 115 cm (45'') 6.7 m (22' 1") 10.4 m (34') 4 cm (1
1
/2") ±19 cm (±7
33
/64")
84'' (213 cm) 186 cm (73'') 105 cm (41'') 6.1 m (20' 2") 9.5 m (31' 1") 3 cm (1
3
/8") ±17 cm (±6
55
/64")
80'' (203 cm) 177 cm (70'') 100 cm (39'') 5.8 m (19' 2") 9.0 m (29' 7") 3 cm (1
5
/16") ±17 cm (±6
17
/32")
72'' (183 cm) 159 cm (63'') 90 cm (35'') 5.3 m (17' 3") 8.1 m (26' 8") 3 cm (1
11
/64") ±15 cm (±5
57
/64")
60'' (152 cm) 133 cm (52'') 75 cm (29'') 4.4 m (14' 5") 6.8 m (22' 2") 2 cm (
63
/64") ±12 cm (±4
29
/32")
40'' (102 cm) 89 cm (35'') 50 cm (20'') 2.9 m (9' 7") 4.5 m (14' 10") 2 cm (
21
/32") ±8 cm (±3
17
/64")
-8
Tele-zoom Lens (AN-C41MZ)
F2.1-F2.8, f=83.5-117.2 mm
NORMAL Mode (4:3)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.10484
χ
L2 (m) = 0.14725
χ
H (cm) =
0.1524
χ
[Feet/inches]
L1 (ft) = 0.10484
χ
/ 0.3048
L2 (ft) = 0.14725
χ
/ 0.3048
H (in) =
0.1524
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.11422
χ
L2 (m) = 0.16042
χ
H (cm) = 0.04151
χ
S (cm) = ±0.20754
χ
[Feet/inches]
L1 (ft) = 0.11422
χ
/ 0.3048
L2 (ft) = 0.16042
χ
/ 0.3048
H (in) = 0.04151
χ
/ 2.54
S (in) = ±0.20754
χ
/ 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
S: Adjustable range of image position (cm/in)
STRETCH Mode (16:9)
Screen Size and Projection Distance
Note
Allow a margin of error in the value in the diagrams above.
When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates
that the bottom of the image is below the lens center.
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
250'' (635 cm) 508 cm (200'') 381 cm (150'') 26.2 m (86') 36.8 m (120' 9")
38 cm (
15")
200'' (508 cm) 406 cm (160'') 305 cm (120'') 21.0 m (68' 10") 29.5 m (96' 7")
30 cm (
12")
150'' (381 cm) 305 cm (120'') 229 cm (90'') 15.7 m (51' 7") 22.1 m (72' 6")
23 cm (
9")
100'' (254 cm) 203 cm (80'') 152 cm (60'') 10.5 m (34' 5") 14.7 m (48' 4")
15 cm (
6")
84'' (213 cm) 171 cm (67'') 128 cm (50'') 8.8 m (28' 11") 12.4 m (40' 7")
13 cm (
5
3
/64")
80'' (203 cm) 163 cm (64'') 122 cm (48'') 8.4 m (27' 6") 11.8 m (38' 8")
12 cm (
4
51
/64")
72'' (183 cm) 146 cm (58'') 110 cm (43'') 7.5 m (24' 9") 10.6 m (34' 9")
11 cm (
4
5
/16")
60'' (152 cm) 122 cm (48'') 91 cm (36'') 6.3 m (20' 8") 8.8 m (29')
9 cm (
3
19
/32")
40'' (102 cm) 81 cm (32'') 61 cm (24'') 4.2 m (13' 9") 5.9 m (19' 4")
6 cm (
2
13
/32")
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
Adjustable range of
image position [S]
Diag. [
χ
]Width Height Minimum [L1] Maximum [L2]
225'' (572 cm) 498 cm (196'') 280 cm (110'') 25.7 m (84' 4") 36.1 m (118' 5") 9 cm (3
43
/64") ±47 cm (±18
25
/64")
200'' (508 cm) 443 cm (174'') 249 cm (98'') 22.8 m (74' 11") 32.1 m (105' 3") 8 cm (3
17
/64") ±42 cm (±16
11
/32")
150'' (381 cm) 332 cm (131'') 187 cm (74'') 17.1 m (56' 3") 24.1 m (78' 11") 6 cm (2
29
/64") ±31 cm (±12
1
/4")
133'' (338 cm) 294 cm (116'') 166 cm (65'') 15.2 m (49' 10") 21.3 m (70') 6 cm (2
11
/64") ±28 cm (±10
7
/8")
106'' (269 cm) 235 cm (92'') 132 cm (52'') 12.1 m (39' 9") 17.0 m (55' 9") 4 cm (1
47
/64") ±22 cm (±8
21
/32")
100'' (254 cm) 221 cm (87'') 125 cm (49'') 11.4 m (37' 6") 16.0 m (52' 8") 4 cm (1
41
/64") ±21 cm (±8
11
/64")
92'' (234 cm) 204 cm (80'') 115 cm (45'') 10.5 m (34' 6") 14.8 m (48' 5") 4 cm (1
1
/2") ±19 cm (±7
33
/64")
84'' (213 cm) 186 cm (73'') 105 cm (41'') 9.6 m (31' 6") 13.5 m (44' 3") 3 cm (1
3
/8") ±17 cm (±6
55
/64")
80'' (203 cm) 177 cm (70'') 100 cm (39'') 9.1 m (30') 12.8 m (42' 1") 3 cm (1
5
/16") ±17 cm (±6
17
/32")
72'' (183 cm) 159 cm (63'') 90 cm (35'') 8.2 m (27') 11.6 m (37' 11") 3 cm (1
11
/64") ±15 cm (±5
57
/64")
60'' (152 cm) 133 cm (52'') 75 cm (29'') 6.9 m (22' 6") 9.6 m (31' 7") 2 cm (
63
/64") ±12 cm (±4
29
/32")
40'' (102 cm) 89 cm (35'') 50 cm (20'') 4.6 m (15') 6.4 m (21' 1") 2 cm (
21
/32") ±8 cm (±3
17
/64")
-9
Changing the Lens
Info
Before changing the lens, turn off the power of the projector and remove the power cord from the wall
outlet.
Do not attempt to change the lens while the projector is mounted on the ceiling.
1 Remove the lens housing cover
by using the supplied lens hous-
ing cover removal tool to push
down on the groove on the lens
housing cover.
Hold down the lens housing cover with
your hand to prevent it from flying out.
2 Slide the lens fastener catch tab
in the direction of “UNLOCK”
while holding the lens to prevent
it from falling out.
Slide the lens fastener catch tab until the
window located beside “LOCK” comes to
the top. Look inside the window to make
sure that the two grooves on the lens fas-
tener ring are facing up.
3 Remove the lens by pulling it
straight out.
4 Remove the protection cap from
the back of the new lens.
Lens fastener catch tab
Two grooves
Window
-10
5
Insert the lens into the projector.
As you insert the lens, look inside the
window to make sure that the pin is in-
serted into the hole of the lens mount.
6 Slide the lens fastener catch tab
in the direction of “LOCK” until
it stops.
Be careful not to rotate the lens fastener
ring too tight, as the lens fastener ring
will be difficult to loosen the next time
the lens is changed.
7 Replace the lens housing cover.
If the lens housing cover is not secured
to the projector, you will not be able to
turn the power on.
Changing the Lens
Lens
mount
Pin
Lens fastener catch tab
-11
RS-232C Terminal: 9-pin mini DIN female connector
Pin No. Signal Name I/O Reference
1 Not connected
2RDReceive Data Input Connected to internal circuit
3SDSend Data Output Connected to internal circuit
4 Not connected
5SGSignal Ground Connected to internal circuit
6 Not connected
7RSRequest to Send Connected to CS in internal circuit
8CSClear to Send Connected to RS in internal circuit
9 Not connected
RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor
Pin No. Signal Name I/O Reference
1 Not connected
2RDReceive Data Input Connected to internal circuit
3SDSend Data Output Connected to internal circuit
4 Not connected
5SGSignal Ground Connected to internal circuit
6 Not connected
7RSRequest to Send Connected to CS in internal circuit
8CSClear to Send Connected to RS in internal circuit
9 Not connected
RS-232C Cable recommended connection: 9-pin D-sub female connector
Pin No. Signal Pin No. Signal
1CD 1 CD
2RD 2 RD
3SD 3 SD
4ER 4 ER
5SG 5 SG
6DR 6 DR
7RS 7 RS
8CS 8 CS
9CI 9 CI
Note
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling
device (e.g. computer).
LAN Terminal : 8-pin RJ-45 modular connector
Pin No. Signal Pin No. Signal
1 TX+ 5
2 TX– 6 RX–
3 RX+ 7
48
8
9
6
5
12
4
3
7
1
6
11
5
15
10
COMPUTER-RGB/COMPONENT INPUT 1, 2 and COMPUTER-RGB/COMPONENT OUTPUT Terminals
:
15-pin mini D-sub female connector
Connecting Pin Assignments
COMPUTER-RGB Input/Output
1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Not connected
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. Not connected
12. Bi-directional data
13. Horizontal sync signal: TTL level
14. Vertical sync signal: TTL level
15. Data clock
Component Input/Output
1. P
R
(C
R
)
2. Y
3. P
B
(C
B
)
4. Not connected
5. Not connected
6. Earth (P
R
)
7. Earth (Y)
8. Earth (P
B
)
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
15
69
51
96
8...1
Projector
Pin No.
4
5
6
Computer
Pin No.
4
5
6
-12
Connecting Pin Assignments
1724
1
9
16
8
Pin No. Signal
1T.M.D.S. Data 2–
2T.M.D.S. Data 2+
3T.M.D.S. Data 2 Shield
4 Not connected
5 Not connected
6 DDC Clock
7 DDC Data
8 Not connected
9T.M.D.S. Data 1–
10 T.M.D.S. Data 1+
11 T.M.D.S. Data 1 Shield
12 Not connected
DVI-D Input Terminal
Pin No. Signal
13 Not connected
14 +5 V Power
15 Ground
16 Hot Plug Detect
17 T.M.D.S. Data 0–
18 T.M.D.S. Data 0+
19 T.M.D.S. Data 0 Shield
20 Not connected
21 Not connected
22 T.M.D.S. Clock Shield
23 T.M.D.S. Clock+
24 T.M.D.S. Clock–
-13
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,
commercially available) to the projector. (See page 27 of the projector’s operation manual for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard. Parity bit: None
Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit
Data length: 8 bits Flow control: None
*Set the projector’s baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Info
When controlling the projector using RS-232C commands from a computer, wait for at least 40 seconds
after the power has been turned on, and then transmit the commands.
After sending an input selection or picture adjustment command and then receiving an “OK” response
code, the projector may take some time to process the command. If a second command is sent while the
projector is still processing the first command, you may receive an “ERR” response code. If this happens,
try resending the second command.
When more than one code is being sent, send each command only after the response code for the previ-
ous command from the projector is verified.
“POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1” “TLTL _ _ _ 1”
“TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”
When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
The special commands are available for applications that require continuous polling.
Return code (0DH)
C1 C2 C3 C4 P1 P2 P3 P4
Response code format
Normal response
Problem response (communication error or incorrect command)
O K
E R R
Command 4-digit Parameter 4-digit
Command format
Return code (0DH)
Return code (
0DH)
RS-232C Specifications and Commands
Note
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under
Control Contents.
*1 Serial No. Check command is used to read out the 12 digits of serial No..
*2 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*3 Parameters of CLR Temp settings are as follows.
*4 The adjustable range of “V-Pos” (V-Position) may vary depending on the screen resolution of the computer.
CLR Temp
5500K
6500K
7500K
Parameter
_0 5 5
_0 6 5
_0 7 5
CLR Temp
8500K
9300K
10500K
Parameter
_0 8 5
_0 9 3
_1 0 5
-14
RS-232C Specifications and Commands
Commands
Example: When turning on the projector, make the following setting.
POWR _ 1__
OK
ProjectorComputer
CONTROL CONTENTS
Power ON
Standby mode
(or 40-second startup time)
COMMAND PARAMETER
RETURN
Power Off
Power On
Power Status
Projector Condition
Lamp Status
Lamp Power Status
Lamp Quantity
Lamp Usage Time (Hour)
Lamp Usage Time (Minute)
Lamp Life (Percentage)
Model Name Check
Model Name Check
Serial No. Check *1
Projector Name Setting 1 (First four characters) *2
Projector Name Setting 2 (Middle four characters) *2
Projector Name Setting 3 (Last four characters) *2
Projector Name Check
COMPUTER 1 (RGB1)
COMPUTER 2 (RGB2)
DVI (RGB3)
INPUT RGB Check
S-VIDEO (Video1)
VIDEO (Video2)
INPUT Video Check
INPUT Mode Check
INPUT Check
All Reset
Volume (0 - 60)
Volume up / down (– 10 - + 10)
Keystone (– 127 - + 127)
AV Mute Off
AV Mute On
Freeze Off
Freeze On
Eco+Quiet Mode : Off
Eco+Quiet Mode : On
Auto Sync Start
COMPUTER 1 Resize : Normal
COMPUTER 1 Resize : Stretch
COMPUTER 1 Resize : Dot By Dot
COMPUTER 1 Resize : Full
COMPUTER 1 Resize : Border
COMPUTER 2 Resize : Normal
COMPUTER 2 Resize : Stretch
COMPUTER 2 Resize : Dot By Dot
COMPUTER 2 Resize : Full
COMPUTER 2 Resize : Border
DVI Resize : Normal
DVI Resize : Stretch
DVI Resize : Dot By Dot
DVI Resize : Full
DVI Resize : Border
POWR___0
POWR___1
POWR????
TABN___1
TLPS___1
TPOW___1
TLPN___1
TLTT___1
TLTM___1
TLTL___1
TNAM___1
MNRD_ _ _1
SNRD___1
PJN1****
PJN2****
PJN3****
PJN0___1
IRGB___1
IRGB___2
IRGB___3
IRGB????
IVED___1
IVED___2
IVED????
IMOD????
ICHK????
ALRE___1
VOLA__**
VOUD_***
KEYS_***
IMBK___0
IMBK___1
FREZ___0
FREZ___1
THMD___0
THMD___1
ADJS___1
RASR___1
RASR___2
RASR___3
RASR___5
RASR___6
RBSR___1
RBSR___2
RBSR___3
RBSR___5
RBSR___6
RCSR___1
RCSR___2
RCSR___3
RCSR___5
RCSR___6
OK or ERR OK
OK OK or ERR
1 0
0:Normal 0:Normal
1:Temp High 1:Temp High
8:Lamp Life 5% or less 2:Fan Error
16:Lamp Burnt-out 4:Cover Open
32:Lamp Ignition Failure 8:Lamp Life 5% or less
16:Lamp Burnt-out
32:Lamp Ignition Failure
64:Temp Abnormally High
0:Off, 1:On, 2:Retry, 3:Waiting, 4:Lamp Error 0:Off, 4:Lamp Error
1:On, 2:Cooling 0:Standby
1
0 - 9999 (Integer)
0, 15, 30, 45
0% - 100% (Integer)
XGC465X / XGC435X
XG-C465X / XG-C435X
Serial No.
OK or ERR
OK or ERR
OK or ERR
Projector Name
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
1:RGB1(COMPUTER1), 2:RGB2(COMPUTER2), ERR
3:RGB3(DVI) or ERR
OK or ERR ERR
OK or ERR ERR
1:S-Video, 2:Video or ERR ERR
1:RGB, 2:Video ERR
1:COMPUTER1, 2:COMPUTER2, 3:DVI, ERR
4:S-Video, 5:Video
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
-15
RS-232C Specifications and Commands
CONTROL CONTENTS
Power ON
Standby mode
(or 40-second startup time)
COMMAND PARAMETER
RETURN
S-Video Resize : Normal
S-Video Resize : Stretch
S-Video Resize : Border
S-Video Resize : Area Zoom
S-Video Resize : V-Stretch
Video Resize : Normal
Video Resize : Stretch
Video Resize : Border
Video Resize : Area Zoom
Video Resize : V-Stretch
COMPUTER 1 Adjustment Reset
COMPUTER 2 Adjustment Reset
DVI Adjustment Reset
S-VIDEO Adjustment Reset
VIDEO Adjustment Reset
COMPUTER 1 Picture Mode : Standard
COMPUTER 1 Picture Mode : Presentation
COMPUTER 1 Picture Mode : Movie
COMPUTER 1 Picture Mode : Game
COMPUTER 1 Picture Mode : sRGB
COMPUTER 1 Contrast (– 30 - + 30)
COMPUTER 1 Bright (– 30 - + 30)
COMPUTER 1 Color (– 30 - + 30)
COMPUTER 1 Tint (– 30 - + 30)
COMPUTER 1 Red (– 30 - 30)
COMPUTER 1 Blue (– 30 - + 30)
COMPUTER 1 Sharp (– 30 - + 30)
COMPUTER 1 CLR Temp *3
COMPUTER 1 Progressive : 2D
COMPUTER 1 Progressive : 3D
COMPUTER 1 Signal Type : Auto
COMPUTER 1 Signal Type : RGB
COMPUTER 1 Signal Type : Component
COMPUTER 2 Picture Mode : Standard
COMPUTER 2 Picture Mode : Presentation
COMPUTER 2 Picture Mode : Movie
COMPUTER 2 Picture Mode : Game
COMPUTER 2 Picture Mode : sRGB
COMPUTER 2 Contrast (– 30 - + 30)
COMPUTER 2 Bright (– 30 - + 30)
COMPUTER 2 Color (– 30 - + 30)
COMPUTER 2 Tint (– 30 - + 30)
COMPUTER 2 Red (– 30 - + 30)
COMPUTER 2 Blue (– 30 - + 30)
COMPUTER 2 Sharp (– 30 - + 30)
COMPUTER 2 CLR Temp *3
COMPUTER 2 Progressive : 2D
COMPUTER 2 Progressive : 3D
COMPUTER 2 Signal Type : Auto
COMPUTER 2 Signal Type : RGB
COMPUTER 2 Signal Type : Component
DVI Picture Mode : Standard
DVI Picture Mode : Presentation
DVI Picture Mode : Movie
DVI Picture Mode : Game
DVI Picture Mode : sRGB
DVI Contrast (– 30 - + 30)
DVI Bright (– 30 - + 30)
DVI Red (– 30 - + 30)
DVI Blue (– 30 - + 30)
DVI CLR Temp *3
RASV___1
RASV___2
RASV___3
RASV__10
RASV__11
RBSV___1
RBSV___2
RBSV___3
RBSV__10
RBSV__11
RARE___1
RBRE___1
RCRE___1
VARE___1
VBRE___1
RAPS__10
RAPS__11
RAPS__12
RAPS__13
RAPS__14
RAPI _ ***
RABR_***
RACO_***
RATI _ ***
RARD_***
RABE_***
RASH_***
RACT_***
RA IP_ __0
RA IP_ __1
IASI___0
IASI___1
IASI___2
RBPS__10
RBPS__11
RBPS__12
RBPS__13
RBPS__14
RBPI _ ***
RBBR_***
RBCO_***
RBTI _ ***
RBRD_***
RBBE_***
RBSH_***
RBCT_***
RB IP_ __0
RB IP_ __1
IBSI___0
IBSI___1
IBSI___2
RCPS__10
RCPS__11
RCPS__12
RCPS__13
RCPS__14
RCPI _ ***
RCBR_***
RCRD_***
RCBE_***
RCCT_***
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
-16
RS-232C Specifications and Commands
CONTROL CONTENTS
Power ON
Standby mode
(or 40-second startup time)
COMMAND PARAMETER
RETURN
DVI Signal Type : D. PC RGB
DVI Signal Type : D. PC Comp.
DVI Signal Type : D. Video RGB
DVI Signal Type : D. Video Comp.
DVI Dynamic Range : Standard
DVI Dynamic Range : Enhanced
S-Video Picture Mode : Standard
S-Video Picture Mode : Presentation
S-Video Picture Mode : Movie
S-Video Picture Mode : Game
S-Video Contrast (– 30 - + 30)
S-Video Bright (– 30 - + 30)
S-Video Color (– 30 - + 30)
S-Video Tint (– 30 - + 30)
S-Video Red (– 30 - + 30)
S-Video Blue (– 30 - + 30)
S-Video Sharp (–30 - + 30)
S-Video CLR Temp *3
S-Video Progressive : 2D
S-Video Progressive : 3D
Video Picture Mode : Standard
Video Picture Mode : Presentation
Video Picture Mode : Movie
Video Picture Mode : Game
Video Contrast (– 30 - + 30)
Video Bright (– 30 - + 30)
Video Color (– 30 - + 30)
Video Tint (– 30 - + 30)
Video Red (– 30 - + 30)
Video Blue (– 30 - + 30)
Video Sharp (– 30 - + 30)
Video CLR Temp *3
Video Progressive : 2D
Video Progressive : 3D
Video System Selection : AUTO
Video System Selection : PAL
Video System Selection : SECAM
Video System Selection : NTSC4.43
Video System Selection : NTSC3.58
Video System Selection : PAL_M
Video System Selection : PAL_N
Video System Selection : PAL-60
Clock (– 30 - + 30)
Phase (– 15 - + 15)
H-Position (– 30 - + 30)
V-Position (– 30 - + 30) *4
Fine Sync Adjustment Reset
Auto Sync : Off
Auto Sync : On
RGB Horizontal Frequency Check
RGB Vertical Frequency Check
Image Shift (– 96 - + 96)
Auto Keystone : Off
Auto Keystone : On
OSD Display : Off
OSD Display : On
Background Selection : Logo
Background Selection : Blue
Background Selection : None
Auto Power Off : Off
Auto Power Off : On
System Sound : Off
System Sound : On
Auto Restart : Off
Auto Restart : On
ICSI___3
ICSI___4
ICSI___5
ICSI___6
HMCD_ __1
HMCD_ __2
VAPS__10
VAPS__11
VAPS__12
VAPS__13
VAPI _***
VABR_***
VACO_***
VATI _***
VARD_***
VABE_***
VASH_***
VACT_***
VA IP___0
VA IP___1
VBPS__10
VBPS__11
VBPS__12
VBPS__13
VBPI _***
VBBR_***
VBCO_***
VBTI _***
VBRD_***
VBBE_***
VBSH_***
VBCT_***
VB IP___0
VB IP___1
ME SY___1
ME SY___2
ME SY___3
ME SY___4
ME SY___5
ME SY___6
ME SY___7
ME SY___8
INCL_***
INPH_***
IAHP_***
IAVP_***
IARE___1
AADJ___0
AADJ___1
TFRQ___1
TFRQ___2
LNDS_***
ATKS___0
ATKS___1
IMDI___0
IMDI___1
IMBG___1
IMBG___3
IMBG___4
APOW___0
APOW___1
SSND___0
SSND___1
ARES___0
ARES___1
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
x10
-1
kHz (***.* or ERR) ERR
Hz (*** or ERR) ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
-17
RS-232C Specifications and Commands
CONTROL CONTENTS
Power ON
Standby mode
(or 40-second startup time)
COMMAND PARAMETER
RETURN
Internal Speaker : Off
Internal Speaker : On
Audio Out : FAO
Audio Out : VAO
PRJ Mode : Reverse Off
PRJ Mode : Reverse On
PRJ Mode : Invert Off
PRJ Mode : Invert On
Fan Mode : Normal
Fan Mode : High
Monitor Out : Disable
Monitor Out : Enable
Language Selection : ENGLISH
Language Selection : DEUTSCH
Language Selection : ESPAÑOL
Language Selection : NEDERLANDS
Language Selection : FRANÇAIS
Language Selection : ITALIANO
Language Selection : SVENSKA
Language Selection :
Language Selection : PORTUGUÊS
Language Selection :
Language Selection :
Language Selection :
Language Selection :
Language Selection : polski
Language Selection : Türkçe
Lamp Timer Reset *5
ASPK___0
ASPK___1
AOUT___1
AOUT___2
IMRE___0
IMRE___1
IMIN___0
IMIN___1
HLMD___0
HLMD___1
MOUT _ _ _ 0
MOUT _ _ _ 1
ME LA___1
ME LA___2
ME LA___3
ME LA___4
ME LA___5
ME LA___6
ME LA___7
ME LA___8
ME LA___9
ME LA__10
ME LA__11
ME LA__12
ME LA__13
ME LA__14
ME LA__15
LPRE0001
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
OK or ERR ERR
ERR OK or ERR
*5 Lamp Timer Reset command is available only in standby mode.
PJLink
TM
Compliant:
This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.
This product confirms with the PJLink standard specification version 1.00.
For additional information, visit “http://pjlink.jbmia.or.jp/english/”.
-18
Page 19
1. Connecting the projector to a computer
Setting up the Projector Network Environment
This section describes the basic procedure for using the projector via the network.
If the network is already constructed, the projector’s network settings may need to be changed. Please
consult your network administrator for assistance with these settings.
You can make network settings both on the projector and on the computer. The following procedure is for
making settings on the computer.
Network settings on the computer
Connect a LAN cable (Category 5, cross-over type) between the computer and projector.
Pages 20, 21
2. Setting an IP address for the computer
Adjust the IP settings of the computer to enable one-to-one communications with the projector.
3. Setting up a network connection for the projector
Adjust the projector network settings to conform to your network.
LAN cable
(commercially available)
Use Internet Explorer
(version 5.0 or later)
to make various
projector settings.
Temporarily change
the computer’s IP
address.
Microsoft
®
and Windows
®
are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
Pages 22, 23
-19
Setting up the Projector Network Environment
1. Connecting the Pro-
jector to a Computer
Establishing a one-to-one connection from the
projector to a computer. Using a LAN cable
(Category 5, cross-over type) you can config-
ure the projector via the computer.
1 Disconnect the computer’s LAN
cable from the existing network.
2 Connect a LAN cable (a UTP
cable, Category 5, cross-over
type) to the projector’s LAN ter-
minal and connect the other end
of the cable to the computer’s
LAN terminal.
3 Plug the power cord into the AC
socket of the projector.
4 Turn on the computer.
Info
Confirm that the LINK LED on the rear of the
projector illuminates. If the LINK LED does not
illuminate, check the following :
The LAN cable is properly connected.
The power switches of both the projector
and the computer are on.
LAN cable
(cross-over type, commercially available)
ON
A LAN cable being
connected to the network
This completes the connection. Now proceed to “2. Setting an IP Address for the Com-
puter”.
-20
Setting up the Projector Network Environment
2. Setting an IP Address
for the Computer
The following describes how to make settings
in Windows
®
XP (Professional or Home Edi-
tion).
1 Log on the network using the
administrator’s account for the
computer.
2 Click “Start”, and click “Control
Panel”.
3 Click “Network and Internet Con-
nections”, and click “Network
Connections” in the new window.
This manual uses examples to explain
the operations in Category View. If you
are using Classic View, double-click
“Network Connections”.
4 Right-click “Local Area Connec-
tion” and select “Properties”
from the menu.
1
2
1
2
1
2
-21
Setting up the Projector Network Environment
1
2
After confirming or setting, proceed to “3. Setting up Network Connection for the Pro-
jector”.
5 Click “Internet Protocol (TCP/IP)”,
and click the “Properties” button.
6 Confirm or change an IP address
for the setup computer.
1 Confirm and note the current IP ad-
dress, Subnet mask and Default
gateway.
Make sure to note the current IP ad-
dress, Subnet mask and Default gate-
way as you will be required to reset
them later.
2 Set temporarily as follows :
IP address : 192.168.150.3
Subnet mask : 255.255.255.0
Default gateway : (Do not input any
values.)
Note
The factory default settings for the projector
are as follows:
DHCP Client : Off
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Default gateway : 0.0.0.0
7 After setting, click the “OK” but-
ton, and then restart the com-
puter.
-22
Setting up the Projector Network Environment
3. Setting up a Network
Connection for the
Projector
Settings for such items as the projector’s IP
address and subnet mask are compatible with
the existing network.
Set each item on the projector as follows. (See
page 53 of the projector’s operation manual
for setting.)
DHCP Client : Off
IP Address : 192.168.150.002
Subnet Mask : 255.255.255.000
1 Start Internet Explorer (version
5.0 or later) on the computer, and
enter “http://192.168.150.2/” in
“Address”, and then press the
“Enter” key.
2 If a user name and a password
have not yet been set, just click
the “OK” button.
If a user name and a password have
been set, input the user name and the
password, and click the “OK” button.
If the user name or password is entered
incorrectly three times, an error mes-
sage will be displayed.
3 When the screen as shown on
the right appears, click “TCP/IP”.
-23
4 The TCP/IP setting screen ap-
pears, ready for network settings
for the projector.
Note
Confirm the existing network’s segment (IP
address group) to avoid setting an IP ad-
dress that duplicates the IP addresses of
other network equipment or computers. If
“192.168.150.2” is not used in the network
having an IP address of “192.168.150.XXX”,
you don’t have to change the projector IP
address.
For details about each setting, consult your
network administrator.
5 Click the “Apply” button.
6 The set values appear. Confirm
that the values are set properly,
and then click the “Confirm” but-
ton.
Setting up the Projector Network Environment
Close the browser.
This completes the network settings.
After setting items, wait for 10 seconds and then re-access.
Change the IP address of the setting computer back to its original address, which you have noted down in
Step 6-1 on page 21, and then connect the computer and the projector to the network.
Setting example / Remarks
Select “ON” or “OFF” to determine
whether to use DHCP
Client
.
You can set this item when “DHCP
Client
is set to “OFF”.
Factory default setting: 192.168.150.2
Enter an IP address appropriate
for the network.
You can set this item when “DHCP
Client
is set to “OFF”.
Factory default setting: 255.255.255.0
Set the subnet mask to the same
as that of the computer and
equipment on the network.
You can set this item when “DHCP
Client
is set to “OFF”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
Items
DHCP
Client
IP Address
Subnet
Mask
Default
Gateway
DNS
Server
-24
Controlling the Projector via LAN
Controlling the Projector
Using Internet Explorer
(Version 5.0 or later)
Complete connections to external equipment
before starting the operation. (See pages 21-
29 of the projector’s operation manual.)
Complete the AC cord connection. (See page
30 of the projector’s operation manual.)
Note
When connecting the projector to the LAN, use
a LAN cable (Category 5). When connecting the
projector to a hub, use a straight-through cable.
1 Start Internet Explorer (version 5.0
or later) on the computer.
2 Enter “http://” followed by the
projector IP address set by the
procedure on page 23 followed
by “/” in “Address”, and then
press the “Enter” key.
The factory default setting for the
projector : “DHCP Client” is “Off and IP
address is “192.168.150.2”. If you did
not change the IP address in “3. Setting
up a Network Connection for the
Projector” (pages 22-23), enter “http://
192.168.150.2/”.
3 A screen for controlling the pro-
jector appears, ready for per-
forming various status condi-
tions, control, and settings.
After connecting the projector to your network, enter the projector IP address in “Address”
on Internet Explorer (version 5.0 or later) using a computer on the network to start a setup
screen that will enable control of the projector via the network.
-25
Confirming the Projector
Status (Status)
On this screen, you can confirm the projector
status. You can confirm the following items :
MAC Address
Power
Condition
Lamp Timer
Lamp Life
Input
Signal Info
Serial Number
Note
If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be dis-
played. Wait for a moment and then oper-
ate again.
For details about each item, refer to the
projector’s operation manual.
Controlling the Projector via LAN
Controlling the Projector
(Control)
On this screen, you can perform projector con-
trol. You can control the following items :
Power
Input Select
Volume
AV Mute
Note
If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
Wait for a moment and then operate again.
You cannot operate this page while the pro-
jector is warming up.
While the projector is in standby mode, you
can only control “Power ON”.
For details about each item, refer to the
projector’s operation manual.
-26
Controlling the Projector via LAN
Setting and Adjusting the
Projector
(Settings & Adjustments)
Example: “Picture” screen display for COMPUTER1
On these screens, you can make projector
settings or adjustments. You can set or adjust
the following items :
Picture Mode
CLR Temp
Progressive (Video)
Signal Type (Computer, DVI)
Dynamic Range (DVI)
Video System (Video)
Resolution Setting
Auto Sync
Resize
Auto Keystone
OSD Display
Background
Eco+Quiet Mode
Auto Power Off
System Sound
Menu Position
Auto Restart
Password
Internal Speaker
Audio Out
Projection Mode
Fan Mode
Monitor Out
RS-232C Speed
All Reset
Language
Note
If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
Wait for a moment and then operate again.
You cannot operate this page while the pro-
jector is warming up.
For details about each item, refer to the
projector’s operation manual.
Setting the Security
(Network – Security)
On this screen, you can make settings relat-
ing to security.
Note
User Name and Password can be up to 8
characters.
You can input the characters below :
a-z, A-Z, 0-9, -, _
Description
Setting of user name for
security protection.
Setting of password for
security protection.
It is possible to set up to three
IP addresses allowing connec-
tion to the projector.
No limits are set to IP addresses
connecting to the projector.
For security improvement, only an
IP address set by “Address 1-3”
can be connected to the projector.
Items
User Name
Password
Accept IP
Address
All IP
Addresses
From only
specific IP
addresses
-27
Controlling the Projector via LAN
Making General Settings
for the Network (Network -
General)
On this screen, you can make general settings
relating to the network.
After clicking the “Apply” button, the set val-
ues appear. Confirm that the values are set
properly, and then click the “Confirm” button.
Note
After setting items, wait for 10 seconds and
then re-access.
Projector Name can be up to 12 characters.
You can input the characters below :
A-Z, 0-9, -, _, (,), space
(When “a-z” are input, they are converted to
A-Z” automatically.)
Description
Setting the projector name.
Setting the time interval in
which the projector will be
automatically disconnected
from the network in units of a
minute (from 1 to 65535
minutes). If the set value is
made 0, the Auto Logout
function is disabled.
Setting the TCP port number
used when exchanging data
with the projector (from 1025 to
65535).
Setting the port number used
when searching for the
projector (from 1025 to 65535).
Items
Projector
Name
Auto
Logout
Time
Data Port
Search
Port
Setting example / Remarks
Setting an SMTP server
address for e-mail transmis-
sion.
e.g.1 : 192.168.150.253
e.g.2 : smtp123.sharp.co.jp
* When using a domain name,
make settings for the DNS
server.
Setting the projector’s e-mail
address. The e-mail address set
here becomes Originator E-mail
Address.
Setting the sender’s name.
The name set here appears in
the “Originator Name” column
of the body of the message.
Items
SMTP
Server
Originator
E-mail
Address
Originator
Name
Setting for Sending E-mail
when an Error Occurs
(Mail – Originator Settings)
On this screen, you can make settings for
sending e-mail to report when the projector
has generated an error.
Note
SMTP Server, Originator E-mail Address and
Originator Name can be up to 64 characters.
You can input the characters below:
SMTP Server and Originator E-mail Address :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {,
|, },
~
, _, ’, ., @, `
(You can input “@” only one time for “Origi-
nator E-mail Address”.)
Originator Name : a-z, A-Z, 0-9, -, _, (,), space
If the settings of “3. Setting up a Network
Connection for the Projector” on pages 22
and 23 are incorrectly set, e-mail will not be
send.
-28
Controlling the Projector via LAN
Setting Error Items and
Destination Addresses to
which E-mail is to be Sent
when an Error Occurs
(Mail – Recipient Settings)
On this screen, you can input e-mail destina-
tions to which error notification (error items)
e-mails are sent.
Note
E-mail Address can be up to 64 characters.
You can input the characters below :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |,
},
~
, _, ’, ., @, `
(You can input “@” only one time.)
For details about error items, refer to the
projector’s operation manual.
Description
Set addresses to which error
notification e-mail is sent. You
can set up to five addresses.
Error e-mail is sent on the error
items checked in their check
boxes.
Send test e-mail. This allows
you to confirm that the settings
for e-mail transmission are
properly set.
Items
E-mail
Address
Error Mail
(Lamp, Temp,
Fan, Cover)
Test
Setting Error Items and
the URL that are to be
Displayed when an Error
Occurs
(Service & Support –
Access URL)
On this screen, you can make settings of the
URL and error items that are to be displayed
when the projector has generated an error.
Example of the display when an error occurs
Description
Set the URL that is to be
displayed when an error
occurs. You can set up to five
addresses.
The URL is displayed when an
error checked in their check
boxes occurs.
The set URL site is test-
displayed. This allows you to
confirm that the URL site is
properly displayed.
Items
Access
URL
Condition
(Always, Lamp,
Temp, Fan, Cover)
Test
-29
Setting up the Projector Using RS-232C or Telnet
When Connecting Using
RS-232C
1 Launch general purpose terminal
emulator.
2 Input settings for the RS-232C port
of the terminal emulator as follows.
Baud Rate : 9600 bps*
Data Length : 8 bit
Parity Bit : None
Stop Bit : 1 bit
Flow Control : None
* This is the factory default setting. If the value
of Baud Rate for the projector has been
changed, set Baud Rate here according to
the changed value on the projector.
3 Input “PJS11234” and press the “En-
ter” key.
4 “OK” is displayed. Input “PJS25678”
and press the “Enter” key within 10
seconds.
5 “User Name:” is displayed. Input the
user name and press the “Enter”
key.
If a user name has not yet been set, just
press the “Enter” key.
6 “Password:” is displayed. Input the
password and press the “Enter” key.
If a password has not yet been set, just press
the “Enter” key.
Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on
the computer to carry out various settings for the projector.
7 Input “setup” and press the “Enter”
key.
SETUP MENU will be displayed.
Note
User name and password are not set in the fac-
tory default settings.
If the user name or password is entered incor-
rectly three times, SETUP MENU will be quit.
SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>
-30
Setting up the Projector Using RS-232C or Telnet
When Connecting Using
Telnet
1 Click “Start” from the Windows
®
desk-
top and select “Run”.
2 Enter “telnet 192.168.150.2” in the text
box that opens up. (If the IP address
of the projector is 192.168.150.2.)
3 Click the “OK” button.
4 “User Name:” is displayed. Input the
user name and press the “Enter”
key.
If a user name has not yet been set, just
press the “Enter” key.
5 “Password:” is displayed. Input the
password and press the “Enter” key.
If a password has not yet been set, just press
the “Enter” key.
6 Input “setup” and press the “Enter”
key.
SETUP MENU will be displayed.
Note
If the IP address has been changed, be sure to
enter the new IP address in step 2.
User name and password are not set in the fac-
tory default settings.
If the user name or password is entered incor-
rectly three times in steps 4 or 5, SETUP MENU
will be quit.
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>
SETUP MENU
-31
Setting up the Projector Using RS-232C or Telnet
SETUP MENU (Main Menu)
[1]IP Address
IP address settings. (Page 34)
[2]Subnet Mask
Subnet mask settings. (Page 34)
[3]Default Gateway
Default gateway settings. (Page 34)
[4]User Name (Factory default setting : Not Re-
quired)
Setting of user name for security protection. (Page 34)
[5]Password (Factory default setting : Not Required)
Setting of password for security protection. (Page 35)
[6]RS-232C Baud Rate (Factory default setting :
9600 bps)
Baud rate settings for the RS-232C terminals. (Page
35)
[7]Projector Name
It is possible to assign a projector name. (Page 35)
[8]DHCP Client
DHCP Client settings. (Page 35)
[A]Advanced Setup
Enters ADVANCED SETUP MENU. (Page 36)
[D]Disconnect All
Disconnect all connections. (Page 36)
[V] View All Setting
Displays all setting values. (Page 32)
Can also be used with ADVANCED SETUP MENU.
[S] Save & Quit
Save set values and quit menu. (Page 33)
[Q]Quit Unchanged
Quit menu without saving setting values. (Page 33)
Note
The factory default settings for the projector are
as follows:
DHCP Client : Off
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Default gateway : 0.0.0.0
ADVANCED SETUP MENU
[1]Auto Logout Time (Factory default setting : 5 min-
utes)
Setting of time until automatic disconnection of net-
work connection. (Page 36)
[2]Data Port (Factory default setting : 10002)
Setting the TCP port number used when exchang-
ing data. (Page 36)
[5]Network Ping Test
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally. (Page 37)
[6]Accept IP Addr(1)
[7]Accept IP Addr(2)
[8]Accept IP Addr(3)
[9]Accept All IP Addr (Factory default setting : Ac-
cept All)
For improved security, it is possible to set up to three
IP addresses allowing connection to the projector.
Set IP addresses can be cancelled using [9] Accept
All IP Addr. (Page 37)
[0] Search Port (Factory default setting : 5006)
Setting the port number used when searching for
the projector. (Page 38)
[!] Restore Default Setting
Restores all setting values that can be set using the
menu to the default state. (Page 38)
[Q]Return to Main Menu
Return to the main SETUP MENU. (Page 38)
SETUP MENU ADVANCED SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>
******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>
-32
View Setting Detail List
([V]View All Setting)
11
11
1 Enter “v” and press the “Enter” key.
Display all setting values(*).
Enter number or symbol of item to be selected on the SETUP MENU. When setting, input the
details to be set. Setting is carried out one item at a time, and saved at the end.
SETUP MENU
Set Items
Example: When setting IP Address (change from
192.168.150.2 to 192.168.150.3)
11
11
1 Enter “1” (number of item to be set), and press
the “Enter” key.
Display current IP address (*1).
22
22
2 Enter IP address to be set and press the “En-
ter” key.
Display IP address after change (*2).
33
33
3 Enter “v” and press the “Enter” key to verify
setting detail list.
IP address is being changed (*3).
Note
Verification of setting detail list can be omitted.
Setting details are not effective until they have
been saved. (Page 33)
If an invalid number is entered, an error message
(“Parameter Error!”) will be displayed.
SETUP MENU
Setting up the Projector Using RS-232C or Telnet
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>v
Model Name : XX-XXXX
Projector Name : XX-XXXX
MAC Address : XX:XX:XX:XX:XX:XX
DHCP Client : Disabled
IP Address : 192.168.150.2
Subnet Mask : 255.255.255.0
Default Gateway : Not Used
RS-232 Baud Rate : 9600 bps
Password : Not Required
**********(Advanced Status)**********
Data Port : 10002
Accept IP Address : Accept All
Auto Logout Time : 5 minutes
Search Port : 5006
1
*
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>1
IP Address : 192.168.150.2
Please Enter : 192.168.150.3
(change) —> 192.168.150.3
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>v
Model Name : XX-XXXX
Projector Name : XX-XXXX
MAC Address : XX:XX:XX:XX:XX:XX
DHCP Client : Disabled
IP Address : 192.168.150.3
Subnet Mask : 255.255.255.0
Default Gateway : Not Used
RS-232C Baud Rate : 9600 bps
Password : Not Required
**********(Advanced Status)**********
Data Port : 10002
Accept IP Address : Accept All
Auto Logout Time : 5 minutes
Search Port : 5006
1
2
3
*1
*2
*3
-33
Save Settings and Quit
([S]Save & Quit)
Save set values and quit menu.
11
11
1 Enter “s” and press the “Enter” key.
22
22
2 Enter “y” and press the “Enter” key.
SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>s
All Connection will be disconnect.
Continue(y/n)? y
Apply New setting...Done.
1
2
Quit without Saving Set-
tings ([Q]Quit Unchanged)
Quit menu without saving setting values.
11
11
1 Enter “q” and press the “Enter” key.
22
22
2 Enter “y” and press the “Enter” key.
SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>q
Quit Without Saving(y/n)? y
Setting Unchanged.
1
2
Setting up the Projector Using RS-232C or Telnet
-34
IP Address Setting
([1]IP Address)
Setting of IP address.
11
11
1 Enter “1” and press the “Enter” key.
22
22
2 Enter numerical value to be set and press the
“Enter” key.
Display IP address after change (*).
Subnet Mask Setting
([2]Subnet Mask)
Setting subnet mask.
11
11
1 Enter “2” and press the “Enter” key.
22
22
2 Enter numerical value to be set and press the
“Enter” key.
Display subnet mask after change (*).
The setting procedure for each item will be explained. For the basic procedure, please refer
to “Set Items” on page 32.
setup>1
IP Address :192.168.150.2
Please Enter :192.168.150.3
(change) —> 192.168.150.3
1
2
*
setup>2
Subnet Mask :255.255.255.0
Please Enter :255.0.0.0
(change) —> 255.0.0.0
1
2
*
Default Gateway Setting
([3]Default Gateway)
Setting default gateway.
11
11
1 Enter “3” and press the “Enter” key.
22
22
2 Enter numerical value to be set and press the
“Enter” key.
Display gateway address after change (*).
Note
If the values for IP Address, Subnet Mask or Gate-
way of the projector have been changed via Telnet,
the computer cannot be connected to the projector
depending on the computer’s network settings.
User Name Setting
([4]User Name)
Carrying out security protection using user name.
11
11
1 Enter “4” and press the “Enter” key.
22
22
2 Enter user name and press the “Enter” key.
Display set user name (*).
Note
User name can be up to 8 characters.
You can input the characters below :
a-z, A-Z, 0-9, -, _
In the default state, user name is not set.
setup>3
note: “0.0.0.0” means “Using no default gateway.”
Gateway Address :0.0.0.0
Please Enter :192.168.150.1
(change) —> 192.168.150.1
1
2
*
setup>4
User Name :
Please Enter : XX-XXXX
(change) —> XX-XXXX
1
2
*
Setting up the Projector Using RS-232C or Telnet
-35
Password Setting
([5]Password)
Carrying out security protection using password.
11
11
1 Enter “5” and press the “Enter” key.
22
22
2 Enter password and press the “Enter” key.
Display set password (*).
Note
Password can be up to 8 characters.
You can input the characters below :
a-z, A-Z, 0-9, -, _
In the default state, the password is not set.
RS-232C Baud Rate Set-
ting ([6]RS-232C Baud Rate)
Setting of baud rate for RS-232C terminals.
11
11
1 Enter “6” and press the “Enter” key.
22
22
2 Select and enter the number 0, 1 or 2 and
press the “Enter” key.
Display set baud rate (*).
Note
Set the projector’s baud rate to the same rate as
that used by the computer.
Projector Name Setting
([7]Projector Name)
It is possible to assign a projector name.
11
11
1 Enter “7” and press the “Enter” key.
22
22
2 Enter projector name.
Display set projector name (*).
Note
Projector name can be up to 12 characters.
You can input the characters below :
A-Z, 0-9, -, _, (,), space
(When “a-z” are input, they are converted to “A-Z”
automatically.)
It is the same as the name which can be con-
firmed or set, using RS-232C commands “PJN0”,
“PJN1”, “PJN2” and “PJN3”.
DHCP Client Setting
([8]DHCP Client)
Setting DHCP Client to “Enable” or “Disable”.
Example: When setting DHCP Client to “Enable”
11
11
1 Enter “8” and press the “Enter” key.
22
22
2 Enter “1” and press the “Enter” key.
Display the obtained values (*).
Setting up the Projector Using RS-232C or Telnet
setup>5
Password :
Please Enter :
sharppj
(change) —> sharppj
1
2
*
setup>6
0 ... 9600 bps
1 ... 38400 bps
2 ... 115200 bps
Baud Rate Select[0-2] :2
RS-232C Baud Rate : 115200 bps
1
2
*
setup>7
Projector Name : XX-XXXX
Please Enter : MY XX-XXXX
(change) —> MY XX-XXXX
1
2
*
setup>8
note: It sets DHCP Client.
0 ... Disable
1 ... Enable
DHCP Select[0-1] : 1
DHCP Client : Enabled
Success get data from DHCP server.
[MAC Address
] : [XX:XX:XX:XX:XX:XX]
[IP Address
] : [192.168.150.2]
[Subnet Mask
] : [255.255.255.0]
[Default Gateway
] : [0.0.0.0]
[DHCP IP Address] : [192.168.150.1]
1
2
*
-36
Disconnecting All Connec-
tions ([D]Disconnect All)
It is possible to disconnect all the TCP/IP connec-
tions currently recognized by the projector. Even if
the COM Redirect port is fixed in the Busy status
due to a problem, it is possible to force the Ready
status back by carrying out this disconnection.
11
11
1 Enter “d” and press the “Enter” key.
22
22
2 Enter “y” and press the “Enter” key.
Note
If Disconnect All is performed, the connection to
the projector via network will be forcibly discon-
nected.
Entering ADVANCED
SETUP MENU
([A]Advanced Setup)
Enters ADVANCED SETUP MENU.
11
11
1 Enter “a” and press the “Enter” key.
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time)
If there is no input after a fixed time, the projector
automatically disconnects network connection using
the Auto Logout function. It is possible to set the time
until the projector is automatically disconnected in
units of a minute (from 1 to 65535 minutes).
11
11
1 Enter “1” and press the “Enter” key.
22
22
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
If the set value is made 0, the Auto Logout func-
tion is disabled.
If an invalid number is entered, an error message
(“Parameter Error!”) will be displayed and the
screen returns to the ADVANCED SETUP MENU.
Data Port Setting
(ADVANCED[2]Data Port)
Setting of TCP port number. It is possible to set in
the range of 1025 to 65535.
11
11
1 Enter “2” and press the “Enter” key.
22
22
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
Set according to need. Normally, use with the fac-
tory default setting.
setup>d
Disconnect All Connections(y/n)?y
Now Disconnecting...
1
2
setup>a
******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>
1
advanced>1
Valid range : 0 to 65535 (minute)
note: if you enter “0”, auto logout function will be disable.
Auto Logout Time : 5
Please Enter :15
(change) —> 15
1
2
*
advanced>2
Valid range :1025 to 65535
Data Port :10002
Please Enter :10005
(change) —> 10005
1
2
*
Setting up the Projector Using RS-232C or Telnet
-37
Carrying out Network Ping
Test
(ADVANCED[5]Network Ping Test)
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally.
11
11
1 Enter “5” and press the “Enter” key.
22
22
2 Enter IP address of device to be tested and
press the “Enter” key.
Display entered IP address (*1).
Display test result (*2).
Note
If the “Enter” key is pressed without entering an
IP address, the Ping destination IP address used
previously is entered.
If there is a fault with the connection, “Error: No
answer” is displayed after a 5 second retry. In this
case, please confirm the settings for the projector
and the computer, and contact your network ad-
ministrator.
Setting of Accept IP Ad-
dress (ADVANCED[6]Accept IP
Addr(1) - [8]Accept IP Addr(3))
It is possible to improve security of the projector by
allowing connection from only a prescribed IP ad-
dress. It is possible to set up to three IP addresses
allowing connection to the projector.
11
11
1 Enter “6”, “7” or “8” and press the “Enter” key.
22
22
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
To invalidate the Accept IP Address being cur-
rently set, enter “0.0.0.0”.
If there is one or more Accept IP Addr being set,
no connections are allowed from IP addresses
that are not yet set. They can be cancelled using
[9]Accept All IP Addr.
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr)
Removes IP addresses set with “Accept IP Addr”.
11
11
1 Enter “9” and press the “Enter” key.
22
22
2 Enter “y” and press the “Enter” key.
Note
At the point in time where “y” was entered, the
numerical values for Accept IP Addr(1)-(3) are
reset to 0.0.0.0”.
If “n” is entered, setting is not altered.
advanced>5
Ping dest IP addr :192.168.150.1
Please Enter :192.168.150.152
(change) —> 192.168.150.152
32 bytes from 192.168.150.152: icmp_seq = 1, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 2, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 3, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 4, time = 0 ms
1
2
*1
*2
advanced>6
Accept IP Addr(1) : 0.0.0.0
Please Enter : 192.168.150.152
(change) —> 192.168.150.152
1
2
*
advanced>9
Accept All IP Addresses(y/n)? y
1
2
Setting up the Projector Using RS-232C or Telnet
-38
Setting of Search Port
(ADVANCED[0]Search Port)
Sets the port number used when searching for the
projector from the network.
11
11
1 Enter “0” and press the “Enter” key.
22
22
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
Set according to need. Normally, use with the fac-
tory default setting.
Return to Default Settings
(ADVANCED[!]Restore Default
Setting)
Returns all menu setting values to the default state.
11
11
1 Enter “!” and press the “Enter” key.
22
22
2 Enter “y” and press the “Enter” key.
Note
If the values for IP Address, Subnet Mask or Gate-
way of the projector have been returned to the
default settings via Telnet, the computer cannot
be connected to the projector depending on the
computer’s network settings.
Return to Main Menu
(ADVANCED[Q]Return to Main Menu)
Returns to the main SETUP MENU.
11
11
1 Enter “q” and press the “Enter” key.
Returns to the SETUP MENU.
advanced>0
Please Enter Port Number for Search from Computer.
Valid range : 1025 to 65535
Search Port : 5006
Please Enter : 5004
(change) —> 5004
1
2
*
advanced>!
Restore All Setting to Default(y/n)? y
— User Setting Initialized —
1
2
advanced>q
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>
1
Setting up the Projector Using RS-232C or Telnet
-39
1 Click “Start”“All Programs”
“Accessories”“Communica-
tions”“HyperTerminal”.
If you do not have HyperTerminal in-
stalled, see the operation manual of your
computer.
Depending on the settings of your com-
puter, you may be required to enter your
area code and other details. Enter the
information as required.
2 Enter a name in the “Name” field,
and click “OK”.
3 If you are required to enter the
area code, enter it in the “Area
code” field. From the “Connect
using” drop-down menu, select
“TCP/IP (Winsock)”, and click
“OK”.
4 Enter the IP address of the pro-
jector in the “Host address” field
(see “TCP/IP” on the “Network”
menu of the projector), and en-
ter the data port of the projector
in the “Port number” field
(“10002” is the factory default
setting), and click “OK”.
Resetting the Lamp Timer of the Projector via LAN
When the projector is connected to a network, you can use HyperTerminal or a similar com-
munications program to send a command to reset the lamp timer. The example below uses
Windows
®
XP as the operating system.
Select
“TCP/IP (Winsock)”
-40
Resetting the Lamp Timer of the Projector via LAN
5 Click “Properties” on the “File”
menu.
6 Click the “Settings” tab, and
then click “ASCII Setup”.
7 Select the check boxes next to
“Send line ends with line feeds”,
“Echo typed characters locally”,
and “Append line feeds to in-
coming line ends”, and click
“OK”.
The LAMPRESET Properties window
appears, click “OK”.
8 If a user name and/or password
is set for the projector, enter the
user name and password.
9 Send the lamp reset command
“LPRE0001”.
This command can only be sent when
the projector is in standby mode.
When “OK” is received, this indicates
that the lamp was successfully reset.
10
Close HyperTerminal.
-41
Communication cannot be established with the projector
When connecting the projector using serial-connection
\ Check that the RS-232C terminal of the projector and a computer or the commercially
available controller are connected correctly.
\ Check that the RS-232C cable is a cross-over cable.
\ Check that the RS-232C port setting for the projector corresponds to the setting for the
computer or the commercially available controller.
When connecting the projector to a computer using network (LAN)-
connection
\ Check that the cable’s connector is firmly inserted in the LAN terminal of the projector.
\ Check that the cable is firmly inserted into a LAN port for a computer or a network device
such as a hub.
\ Check that the LAN cable is a Category 5 cable.
\ Check that the LAN cable is a cross-over cable when connecting the projector to a computer
directly.
\ Check that the LAN cable is a straight-through cable when connecting the projector with a
network device such as a hub.
\ Check that the power supply is turned on for the network device such as a hub between the
projector and a computer.
Check the network settings for the computer and the projector
\ Check the following network settings for the projector.
IP Address
Check that the IP address for the projector is not duplicated on the network.
Subnet Mask
When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for
the projector and the default gateway setting for the computer are the same:
The subnet masks for the projector and the computer should be the same.
The IP address parts shown by the subnet mask for the projector and the computer should
be the same.
(Example)
When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the
projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the
subnet mask should be “255.255.255.0”.
Gateway
When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for
the projector and the default gateway setting for the computer are the same:
The subnets for the projector and the computer should be the same.
The IP address parts shown by the subnet mask for the projector and the computer should
be the same.
(Example)
When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the
projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the
subnet mask should be “255.255.255.0”.
Note
The factory default settings for the projector are as follows:
DHCP Client : Off
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Gateway address : 0.0.0.0 (Not Used)
For network settings for the projector, refer to page 22.
Troubleshooting
-42
Troubleshooting
\ Take the following steps for checking the network settings for the computer.
1. Open a command prompt (MS-DOS Prompt).
In the case of Windows
®
98 or 98SE: click “START” “Programs” “MS-DOS Prompt” in
order.
In the case of Windows
®
Me: click “START” “Programs” “Accessories” “MS-DOS
Prompt” in order.
In the case of Windows
®
2000: click “START” “Programs” “Accessories” “Command
Prompt” in order.
In the case of Windows
®
XP: click “START” “All Programs” “Accessories” “Command
Prompt” in order.
2. After launching the command prompt (MS-DOS Prompt), enter the command “ipconfig”,
and press the “Enter” key.
Note
Communication may not be established even after carrying out the network settings
for the computer. In such cases, restart your computer.
C:\>ipconfig
Note
Usage examples of ipconfig
C:\>ipconfig /? displays how to use “ipconfig.exe”.
C:\>ipconfig displays the set IP address, subnet mask and default gateway.
C:\>ipconfig /all displays all the setting information related to TCP/IP.
3. To return to the Windows
®
screen, enter “exit” and press the “Enter” key.
-43
\ Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, check
if an IP address is set.
1. Open a command prompt (MS-DOS Prompt).
In the case of Windows
®
98 or 98SE: click “START” “Programs” “MS-DOS Prompt” in
order.
In the case of Windows
®
Me: click “START” “Programs” “Accessories” “MS-DOS
Prompt” in order.
In the case of Windows
®
2000: click “START” “Programs” “Accessories” “Command
Prompt” in order.
In the case of Windows
®
XP: click “START” “All Programs” “Accessories” “Command
Prompt” in order.
2. After launching the command prompt (MS-DOS Prompt) enter a command “PING”.
Entry example C:\>Ping XXX.XXX.XXX.XXX
“XXX.XXX.XXX.XXX” should be entered with an IP address to be connected to, such as
the projector.
3. When connecting normally, the display will be as follows.
(The screen may be slightly different depending on the OS type).
<Example> when the IP address connected to is “192.168.150.2”
4. When a command cannot be sent, “Request time out” will be displayed.
Check the network setting again.
If communication can still not be established properly, contact your network administrator.
5. To return to the Windows
®
screen, enter “exit” and then press the “Enter” key.
A connection cannot be made because you have forgotten your user name or your password.
\ Initialize the settings. (See page 54 of the projector’s operation manual.)
\ After the initialization, carry out setting again.
Troubleshooting
-44
Dimensions
Units: inches (mm)
Side View Side View
Top View
Rear View
Front View
Bottom View
11
1
/64 (279.5)
17
/64
(6.5)
1
/4 (6)
12
27
/32 (326)
3
31
/64 (88.5)
2
15
/16
(74.5)
5
53
/64 (148) 5
53
/64 (148)
4 (101.5)
1
31
/32
(50)
3
1
/64 (76.5)
63
/64
(25)
2
61
/64
(75)
5
25
/32 (146.5)
9
9
/32 (235.5)
10
37
/64 (268.5)
1
5
/64
(27.25)
2
29
/32
(73.5)
-45
Dimensions
Projector and Lens Dimensions
[When AN-C12MZ is installed]
Unit : inches (mm)
15
21
/64 - 15
13
/32 (389 - 391)
107
[When AN-C18MZ is installed]
Unit : inches (mm)
12
3
/32 - 12
11
/64 (307 - 309)
67.5
[When AN-C27MZ is installed]
Unit : inches (mm)
13
7
/16 - 13
5
/8 (341 - 346)
80
[When AN-C41MZ is installed]
Unit : inches (mm)
13
19
/32 - 13
3
/4 (345 - 349)
80
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sharp XG-C465X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sharp XG-C465X in de taal/talen: Engels als bijlage per email.

De handleiding is 1,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Sharp XG-C465X

Sharp XG-C465X Snelstart handleiding - Nederlands - 45 pagina's

Sharp XG-C465X Gebruiksaanwijzing - Nederlands - 71 pagina's

Sharp XG-C465X Gebruiksaanwijzing - Deutsch - 71 pagina's

Sharp XG-C465X Gebruiksaanwijzing - Deutsch - 45 pagina's

Sharp XG-C465X Gebruiksaanwijzing - English - 71 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info