16869

Sharp UXCC500 Handleiding

1
Verklein
Vergroot
Pagina terug
1/139
Pagina verder
MODEL
UX-CC500
FACSIMILE
OPERATION MANUAL
1. Installation
2. Using the Cordless Handset
3. Using the Answering System
4. Sending Faxes
5. Receiving Faxes
6. Making Copies
7. Special Functions
8. Printing Lists
9. Maintenance
10. Troubleshooting
UX-CC500 FACSIMILE
Sharp
Place
congratulations
on the purchase of your new Sharp Product!
For your convenience, Genuine Sharp Supplies, Accessories, and
additional Sharp Products can be purchased from the Authorized Sharp
Reseller where you purchased your product or on-line at:
www.SharpPlace.com
visit SharpPlace
to enter periodic contests and drawings!
2002 Sharp Electronics Corporation
Design and specifications are subject to change without notice.
To ensure Sharp
quality, look for
the Sharp Genuine
Supplies Logo on
Your business
products. We
provide a full line
of supplies that
are designed and
tested to maximize
the life and
performance of all
Sharp products.
FROM SHARP MINDS
COME SHARP PRODUCTS
TM
C
WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTICE
Fax machine
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for at uncontrolled
equipment.
This equipment should be installed and operated with minimum distance at least 20cm
between the radiator and persons body (excluding extremities: hands, wrists, feet and legs)
and must not be co-located or operated with any other antenna or transmitter.
Cordless handset
For body worn operation, this phone has been tested and meets FCC RF exposure gudelines
when used with an accessory that contains no metal and that positions the handset a
minimum of 1.5cm from the body.
Use of other accessories may not ensure compliance with FCC RF exposure guidelines.
ABOUT THE TELEPHONE CONSUMER PROTECTION ACT OF 1991
"The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a
computer or other electronic device to send any message via a telephone facsimile machine
unless such message clearly contains in a margin at the top or bottom of each transmitted
page or on the first page of the transmission the following information:
(1) The date and time of transmission.
(2) Identification of either the business, business entity or individual sending the message.
(3) Telephone number of either the sending machine, business, business entity or individual.
In order to program this information into your facsimile machine, please refer to the
appropriate instructions in the operation manual."
As an
ENERGY STA R
partner, SHARP has
determined that this product meets the
ENERGY
STAR
guidelines for energy efficiency.
FCC-15.fmPage1Friday,May31,200210:48AM
1
Introduction
Fax machine and general specifications.
*Based on Sharp Standard No. 1 Chart at standard resolution in Sharp special mode,
excluding time for protocol signals (i.e., ITU-T phase C time only).
Automatic dialing Common book: 40 numbers
Private book: 5 numbers (each cordless
handset has 1 private book)
Imaging film Initial starter roll (included with machine):
32 ft. (10 m) (approx. 30 letter-size pages)
Replacement roll (not included):
UX-5CR 164 ft. (50 m) (one roll yields
approx. 150 letter-size pages)
Memory size* 448 KB (approx. 24 average pages with no
voice messages recorded, or 20 minutes of
voice messages (including OGMs) with no
faxes in memory)
Modem speed 14,400 bps with automatic fallback to lower
speeds.
Transmission time* Approx. 6 seconds (only when ECM is on)
Resolution Horizontal: 203 pels/inch (8 pels/mm)
Vertical:
Standard: 98 lines/inch (3.85 lines/mm)
Fine /Halftone: 196 lines/inch (7.7 lines/mm)
Super fine: 391 lines/inch (15.4 lines/mm)
Automatic document feeder 10 pages max. (letter/A4, 20 lb paper)
Recording system Thermal transfer recording
Display 16-digit LCD display
In addition to the cordless handset
that comes with the fax machine, you
can purchase up to three accessory
cordless handsets. The cordless
handsets can be used as an
intercom system, and each cordless
handset has its own personal box in
the answering system.
Welcome, and thank
you for choosing a
SHARP UX-CC Series
fax machine and
cordless handset!
all.bookPage1Friday,May31,20029:49AM
2
Halftone (grayscale) 64 levels
Compression scheme MR, MH, MMR
Applicable telephone line Public switched telephone network
Paper tray capacity Letter: Approx. 50 sheets (20-lb. copier paper
at room temperature; maximum stack height
should not be higher than the line on the tray)
Legal: 5 sheets
Recommended paper weight: 20-lb. Copy
Bond
Compatibility ITU-T (CCITT) G3 mode
Input document size Automatic feeding:
Width: 5.8 to 8.5" (148 to 216 mm)
Length: 5.5 to 11" (140 to 279 mm)
Manual feeding:
Width: 5.8 to 8.5" (148 to 216 mm)
Length: 5.5 to 23.6" (140 to 600 mm)
Effective scanning width 8.3" (210 mm) max.
Effective printing width 8.3" (210 mm) max.
Contrast control Automatic/Dark selectable
Reception modes TEL/FAX/TAD
Copy function Single / Multi (99 copies/page)
Telephone function Yes (cannot be used if power fails)
Power requirements 120 V AC, 60 Hz
Operating temperature 41 - 95°F (5 - 35°C)
Humidity 25 - 85% RH
Power consumption Standby: 4.3 W
Maximum: 100 W
Dimensions (without
attachments)
Width: 13.9" (353 mm)
Depth: 7.6" (193 mm)
Height: 6.9" (174 mm)
Weight (without
attachments)
Approx. 6.2 lbs. (2.8 kg)
all.bookPage2Friday,May31,20029:49AM
3
Cordless handset specifications
Frequency 2.4 GHz (2.405 to 2.475 GHz)
Dimensions Width: 1.8" (46 mm)
Depth: 1.7" (42 mm)
Height: 7.1" (180 mm) (not including antenna)
Weight Approx. 0.3 lbs. (115 g) (without battery)
Battery 3.6 V Ni-MH battery; capacity: 850 mAh
Power consumption
Initial charging
Battery life
Battery life in standby
mode
Approx. 1.0 W (in standby mode)
Approx. 10 hours for initial charge
Approx. 4 hours (240 minutes) (at room temp.)
Approx. 3 days with one full charge (at room
temperature)
Battery life (both normal and in standby mode)
may vary depending on usage, range from
base machine, and environmental conditions
such as temperature.
Accessory cordless handset UX-K01 (up to 3 handsets can be added)
As a part of our policy of continuous improvement, SHARP reserves the right to make design
and specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
Important: This fax machine is not designed for use on a line which has call waiting, call
forwarding, or certain other special services offered by your telephone company. If you
attempt to use the fax machine in conjunction with any of these services, you may experience
errors during transmission and reception of facsimile messages. The fax machine is not
compatible with digital telephone systems.
Important safety information
Do not disassemble this machine or attempt any procedures not described in this manual.
Refer all servicing to qualified service personnel.
Do not install or use the machine near water, or when you are wet. For example, do not use
the machine near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or
near a swimming pool. Take care not to spill any liquids on the machine.
Unplug the machine from the power outlet and telephone jack and consult a qualified service
representative if any of the following situations occur:
- Liquid has been spilled into the machine or the machine has been
exposed to rain or water.
all.bookPage3Friday,May31,20029:49AM
4
- The machine produces odors, smoke, or unusual noises.
- The power cord is frayed or damaged.
- The machine has been dropped or the housing damaged.
Do not allow anything to rest on the power cord, and do not install the machine where people
may walk on the power cord.
This machine must only be connected to a 120 V, 60 Hz, grounded (3-prong) outlet.
Connecting it to any other kind of outlet will damage the machine and invalidate the warranty.
Never insert objects of any kind into slots or openings on the machine. This could create a risk
of fire or electric shock. If an object falls into the machine that you cannot remove, unplug the
machine and consult a qualified service representative.
Do not place this machine on an unstable cart, stand or table. The machine could be seriously
damaged if it falls.
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
Never touch bare telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be
a remote risk of electric shock from lightning.
Do not use a telephone to report a gas leak in the vicinity of the leak.
The power outlet must be installed near the equipment and must be easily accessible.
Battery
Use only the battery specified in this manual. Use only the provided charger to charge the
battery.
Do not open or mutilate the battery pack. Corrosive fluid may leak out and cause injury or
burns to the eyes and skin. The fluid may be toxic if swallowed. In case of contact with eyes,
flush with clean water (do not rub), and seek medical attention immediately.
Do not store or carry the battery with other metal objects such as keys or pins. These may
short the battery and cause it to overheat.
Do not allow the battery to become wet.
Do not dispose of the battery in a fire or heat the battery. The battery may explode.
Health care facilities and equipment
Radio frequency energy emitted from the cordless handset equipment may cause medical
equipment to malfunction. Verify that any personal medical equipment you are using is
adequately shielded from external radio frequency energy before using the cordless handset
equipment. Do not use the cordless handset equipment in health care facilities where such
use is prohibited.
all.bookPage4Friday,May31,20029:49AM
5
Table of Contents
A Look at the Operation Panel 7
1. Installation 12
Unpacking Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Loading the Imaging Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Loading Printing Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Entering Your Name and Fax Number . . . . . . . . . . . . . . . . . . . . . . . 26
Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setting the Reception Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Volume Adjustment - Fax Machine. . . . . . . . . . . . . . . . . . . . . . . . . . 31
Volume Adjustment - Cordless Handset. . . . . . . . . . . . . . . . . . . . . . 32
2. Using the Cordless Handset 34
Making a Phone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Receiving a Phone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Receiving a Fax Using the Cordless Handset . . . . . . . . . . . . . . . . . 36
Storing and Using Auto-Dial Numbers . . . . . . . . . . . . . . . . . . . . . . . 36
Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Using the Intercom Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Transferring Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3. Using the Answering System 47
Recording an Outgoing Message. . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting a Passcode for a Personal Box . . . . . . . . . . . . . . . . . . . . . . 49
Operating the Answering System. . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Optional Answering System Settings . . . . . . . . . . . . . . . . . . . . . . . . 56
Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Remote Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4. Sending Faxes 69
Transmittable Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Loading the Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Adjusting the Resolution and Contrast . . . . . . . . . . . . . . . . . . . . . . . 71
Sending a Fax by Normal Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . 73
all.bookPage5Friday,May31,20029:49AM
Table of Contents
6
Sending a Fax by Automatic Dialing. . . . . . . . . . . . . . . . . . . . . . . . . 74
Sending a Fax From Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5. Receiving Faxes 83
Using FAX Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Using TEL Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Optional Reception Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Substitute Reception to Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6. Making Copies 89
7. Special Functions 91
Caller ID (Requires Subscription to Service) . . . . . . . . . . . . . . . . . . 91
Distinctive Ring (Requires Subscription to Service) . . . . . . . . . . . . . 97
Blocking Reception of Unwanted Faxes . . . . . . . . . . . . . . . . . . . . . . 98
8. Printing Lists 99
9. Maintenance 103
Replacing the Cordless Handset Battery . . . . . . . . . . . . . . . . . . . . 106
10. Troubleshooting 108
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Messages and Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Ordering Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
FCC Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Quick Reference Guide 125
Guía de referencia rápida 127
Index 129
all.bookPage6Friday,May31,20029:49AM
7
Display
This displays messages and prompts to help you operate the machine.
INTERCOM key
Press this key to page or locate the cordless handset.
REC/MEMO key
Press this key to record an outgoing message, phone conversation, or memo.
PLAY key
Press this key to play recorded messages.
Left and right arrow keys
Auto-dial numbers: When sending a fax or making a phone call, press these
keys to scroll through your auto-dial numbers, the “REVIEW CALLS” list (only
available if you have Caller ID), and the last number dialed (redial).
FUNCTION key settings: Press the right arrow key after scrolling with the up
and down arrow keys to select a FUNCTION key setting.
Number keys
Use these keys to dial numbers, and enter numbers and letters when storing
auto-dial numbers.
Panel release
Press this release to open the operation panel.
A Look at the Operation Panel
Fax machine
1
2
3
4
5
6
7
REC/
MEMO
PLAY
JKL
DELETE
REPEAT
ABC
1
DEF
WXYZ
9
GHI
4
5
MNO
6
PQRS
TEL
TAD
FAX
STOP
COPY/HELP
START/MEMORY
RESOLUTION/
RECEPTION MODE
INTERCOM
FUNCTION
REDIAL
Z A
SPEAKER
7
TUV
8
SKIP
0
2 3
1
8 9 10 12 14
5 6 7
D
O
W
N
U
P
11 15 16 17
32 4
13
all.bookPage7Friday,May31,20029:49AM
8
STOP key
Press this key to cancel an operation before it is completed.
COPY/HELP key
When a document is in the feeder, press this key to make a copy of a
document. At any other time, press this key to print out the Help List, a quick
reference guide to the operation of your fax machine.
START/MEMORY key
Press this key after dialing to begin fax transmission. Press this key before
dialing to send a fax through memory. The key can also be pressed in the date
and time display to show the percentage of memory currently used.
RESOLUTION / RECEPTION MODE key
When a document is in the feeder, press this key to adjust the resolution for
faxing or copying. At any other time, press this key to select the reception
mode (an arrow in the display will point to the currently selected reception
mode).
FUNCTION key
Press this key followed by the arrow keys to select special functions and
settings.
UP and DOWN arrow keys
Enlarge/reduce setting: When making a copy of a document, press these
keys to select an enlarge/reduce setting.
Volume setting: When a document is not in the feeder, press these keys to
change the handset volume when the handset is lifted, the speaker volume
when the SPEAKER key has been pressed, or the ringer volume at any other
time.
FUNCTION key settings: Press these keys after pressing the FUNCTION
key to scroll through the FUNCTION MODE settings.
SPEAKER key
Press this key to listen to the line and fax tones through the speaker when
faxing a document.
Note: This is not a speakerphone. You must pick up the handset to talk with
the other party.
REPEAT key
Press this key while listening to a message to play it again.
SKIP key
Press this key while listening to a message to skip to the next message.
DELETE key
Press this key to erase recorded messages.
12
11
10
9
13
14
15
16
17
8
all.bookPage8Friday,May31,20029:49AM
9
Antenna
Display
This displays messages and prompts to help you use the cordless handset.
UP and DOWN arrow keys
Receiver volume: When talking on the cordless handset, press these keys to
adjust the receiver volume. This also adjusts the volume when using a
headset (purchased separately) connected to the cordless handset.
Ringer volume: When not talking on the cordless handset, press these keys
to adjust the cordless handset ringer volume.
Scroll through numbers: Press these keys to scroll when searching for an
auto-dial number or reviewing received calls (only available when you have
Caller ID).
FUNCTION/PAUSE key
Press this key to after pressing to store a new auto dial number.
When entering an auto-dial number, press this key to insert a pause between
digits.
SEARCH
1
2
3
4
FUNCTION
/PAUSE
TALK
OFF
REMOTE
/FLASH
START
UP
DOWN
PLAY NEW
PLAY
REPEAT SKIP DELETE
ERASE
STOP
RECEPTION
REVIEW
INTER
COM
HOLD
REDIAL
SEARCH
1
ABC DEF
JKLGHI MNO
TUVPQRS WXYZ
23
456
789
0
7
18
11
19
17
1
3
4
5
6
14
16
20
21
8
13
12
2
22
23
15
10
9
Cordless handset
all.bookPage9Friday,May31,20029:49AM
10
TALK key
Press this key to make or answer a call.
REVIEW (left) arrow key
Press the REVIEW arrow key and then the UP or DOWN arrow key to scroll
through your 30 most recent calls (only available if you have Caller ID). This
key can also be used to move the cursor left when entering or editing an auto-
dial number or name.
Number keys
Use these keys to dial numbers, and enter numbers and letters when storing
auto-dial numbers.
PLAY NEW key
Press this key after pressing to listen to new messages recorded in the
personal box corresponding to the cordless handset.
PLAY key
Press this key after pressing to listen to all messages recorded in the
personal box corresponding to the cordless handset.
REPEAT key
Press this key while listening to a message to play it again.
INTERCOM key
Press this key to page the fax machine or another cordless handset.
START key
Press this key to start fax reception from the cordless handset, or to complete
entries when storing, editing, or deleting auto-dial numbers.
REMOTE/FLASH key
Press this key to perform remote operations on the fax machine. The key is
also used to access special services from your phone company that require
subscription (contact your phone company for details).
OFF key
Press this key to end a call.
SEARCH (right) arrow key
Press the SEARCH arrow key and then the UP or DOWN arrow key to scroll
through your auto-dial numbers. This key can also be used to move the cursor
right when entering or editing an auto-dial number or name.
REMOTE
/FLASH
REMOTE
/FLASH
6
7
8
12
11
10
9
13
14
15
5
all.bookPage10Friday,May31,20029:49AM
11
RECEPTION key
Press this key after pressing to change the reception mode on the fax
machine.
STOP key
Press this key to stop playback of messages.
DELETE
Press this key while listening to a message to delete it. To delete all your
messages, press this key after playback ends (while the display shows
REMOTE MODE), followed by .
HOLD/ERASE key
Hold: Press this key during a call to put the other party on hold.
Erase: Press this key to delete a phone number when searching through your
recently received calls (only when you have Caller ID), or when searching
through your auto-dial numbers. Press the key to delete a digit or character
when storing or editing an auto-dial number.
SKIP key
Press this key while listening to your messages to skip to the next message.
REDIAL key
Press this key to redial the last number dialed using the cordless handset.
Headset jack
This jack lets you connect a headset (purchased separately) to the cordless
handset.
Battery cover
Remove this cover to install or replace the handset battery.
REMOTE
/FLASH
START
17
16
18
19
20
21
22
23
all.bookPage11Friday,May31,20029:49AM
12
1. Installation
Unpacking Checklist
Paper tray Paper tray
extension
Operation
manual
Gears (2)
Handset Handset
cord
Telephone
line cord
Imaging film
(initial starter roll)
Cordless
handset
Battery
cover
Battery
pack
Cordless
handset charger
AC adapter
If any are missing,
contact your
dealer or retailer.
Before setting up,
make sure you
have all of the
following items.
all.bookPage12Friday,May31,20029:49AM
Setting Up
13
1. Installation
Setting Up
Selecting a location for the fax machine
To maximize the talking range of the cordless handset, we recommend
installing the fax machine in a high and central location away from
obstructions such as walls.
Do not place the
machine in direct
sunlight.
Do not place the
machine near
heaters or air
conditioners.
Keep dust away from
the machine.
Keep the area
around the
machine clear.
Keep the fax machine away
from other electrical
appliances such as TVs,
microwave ovens,
computers, and other
cordless phones.
High and central
location with no
obstructions
all.bookPage13Friday,May31,20029:49AM
Setting Up
14
Connecting the power cord
Plug the power cord into a 120 V, 60 Hz, grounded AC (3-prong) outlet.
Caution!
Do not plug the power cord into any other kind of outlet. This will damage the
machine and is not covered under the warranty.
The machine does not
have a power on/off
switch, so the power is
turned on and off by
simply plugging in or
unplugging the power
cord.
Connecting the handset
Connect the handset as shown and place it on the handset rest.
♦ The ends of the handset cord are identical, so they will go into either jack.
Make sure the handset
cord goes into the jack
marked with a handset
symbol on the side of
the machine!
Use the handset to make ordinary phone calls,
or to transmit and receive faxes manually.
all.bookPage14Friday,May31,20029:49AM
Setting Up
15
1. Installation
Connecting the telephone line cord
Insert one end of the line cord into the jack on the back of the machine
marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line
wall telephone jack.
TEL.LINE
Setting the dial mode
The fax machine is set for tone dialing. If you are on a pulse dial line, you must
set the fax machine for pulse dialing. Press the panel keys as follows:
1 Press once and once.
2 Press once and twice.
3 Press once.
4 Select the dial mode:
TONE: PULSE:
5 Press to exit.
FUNCTION
1
2
STOP
Display:
The display briefly shows
your selection, then:
OPTION SETTING
DIAL MODE
DISTINCTIVE
1=TONE, 2=PULSE
all.bookPage15Friday,May31,20029:49AM
Setting Up
16
Note: If your area experiences a high incidence of lightning or power surges,
we recommend that you install surge protectors for the power and telephone
lines. Surge protectors can be purchased at most telephone specialty stores.
Attach the paper tray and paper tray extension
Attach the paper tray.
Note: The paper tray extension has a top side
and a bottom side. If the tabs do not go into
the holes, turn the support over.
About condensation
If the machine is moved from a cold to a warm place, it is possible that
condensation may form on the scanning glass, preventing proper scanning of
documents for transmission. To remove the condensation, turn on the power and
wait approximately two hours before using the machine.
Insert
horizontally
and rotate up
Attach the paper tray extension.
Click!
all.bookPage16Friday,May31,20029:49AM
Setting Up
17
1. Installation
Connecting the cordless handset charger
1 Connect the AC adapter to the cordless
handset charger.
2 Plug the AC adapter into a standard
120 V AC outlet.
Important: Never cover the charger and AC adapter with a blanket, cloth, or
other material. Excessive heating may result and cause fire.
Raising the base antenna
Raise the base antenna to ensure clear communication with the cordless
handset.
Fit the cord into
the holders.
all.bookPage17Friday,May31,20029:49AM
Setting Up
18
Installing the battery and charging the cordless handset
1 Connect the battery connector ➊1 Connect the battery connector ➊, and then place the battery pack in the
cordless handset.
• Place the wires as shown.
2 Place the battery cover on the cordless
handset, making sure it snaps firmly
into place.
• Make sure the wires are not caught or
pinched by the cover.
3 Place the cordless handset in the
charger with the dial pad facing
forward.
• Important! The dial pad must face
forward, or the battery will not charge.
• The battery charges automatically while
the cordless handset is in the charger.
While charging, the display shows
CHARGING. When charging is
completed, the display shows IN
CHARGER.
• The cordless handset and charger may
feel warm while charging. This is
normal.
The battery cannot be overcharged. When not using the cordless handset,
keep it in the charger to ensure that it is always charged.
Charge the battery
at least
10 hours
the first time!
Black
Red
Black
Red
all.bookPage18Friday,May31,20029:49AM
Setting Up
19
1. Installation
When the battery needs charging, LOW BATTERY will appear in the display
and you will hear beeps during a phone conversation. If you need to continue
the conversation, press to transfer the call to the fax machine. Place the
cordless handset in the charger and let it charge.
Note: If the battery is extremely low, nothing may appear in the display during
the first several minutes that the cordless handset is in the charger. The
battery will begin to charge normally after several minutes.
INTER
COM
Reinforced concreteMetalAluminum sash
Talking range
The talking range of the cordless handset is approximately 1200 ft. (400 m)
(line of sight). If you hear noise or interference while talking on the cordless
handset, move closer to the fax machine.
♦ When outside the talking range, OUT OF RANGE appears in the display. If
you move out of the talking range while talking on the cordless handset,
the handset will beep and you may hear interference.
Large metal objects,
metal structures, and
thick walls reduce the
talking range.
To ensure that the battery
charges properly, wipe the
charger contacts once a
month with a cotton swab.
all.bookPage19Friday,May31,20029:49AM
Setting Up
20
Entering a name for the cordless handset
You can enter a name for the cordless handset in the fax machine.
♦ The fax machine will transmit the name that you enter to your cordless
handset. The name will appear in the cordless handset’s display.
1 Press once and 3 times on
the fax machine.
2 Press once and once.
3 Press once.
4 Press to select SET.
5 Press . (“1” is the ID number of the
cordless handset that came with the
fax machine.)
6 Enter the name by pressing number keys for each letter as shown in the
chart below. Up to 10 characters can be entered.
Example: BILL = 22 444 555 555
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
♦ To clear a mistake, press .
FUNCTION
1
1
SPEAKER
Fax machine display:
ENTRY MODE
HS NAME SET
1=SET, 2=CLEAR
SELECT ID NO. 1
SELECT HS NO.
A =
B =
C =
D =
E =
F =
G =
H =
I =
J =
K =
L =
M =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
X =
Y =
Z =
SPACE =
all.bookPage20Friday,May31,20029:49AM
Setting Up
21
1. Installation
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears.
♦ To enter one of the following symbols, press or repeatedly:
. / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | }
) (
7 Press to store the name.
8 Press to exit.
START/MEMORY
STOP
Connecting a headset
You can connect a headset (purchased separately) to the headset jack.
Remove the cap and insert the connector as shown.
Accessory cordless handsets
You can use up to 3 additional
UX-K01 cordless handsets
with the fax machine.
For information on setting up an accessory cordless handset for use with the
fax machine, see the manual that accompanies the accessory handset.
Please purchase accessory
UX-K01 handsets at your
dealer or retailer.
OWN
NUMBER SET
Display:
HANDSET1
BILL
The handset number
and name appear in
the standby display of
the cordless handset
all.bookPage21Friday,May31,20029:49AM
Loading the Imaging Film
22
Loading the Imaging Film
Your fax uses a roll of imaging film to create printed text and images. The print
head in the fax applies heat to the imaging film to transfer ink to the paper.
Follow the steps below to load or replace the film.
1 Remove the paper from the paper tray
and open the operation panel (press
➊).
2 Remove the used film and
empty spool.
3 Remove the two green gears from the
spools.
DO NOT DISCARD THE TWO GREEN
GEARS!
1
2
When replacing the film,
use a roll of Sharp UX-
5CR imaging film. One
roll can print about 150
letter-size pages.
The initial starter roll of
imaging film included with
your fax can print about
30 letter-size pages.
If you are loading the imaging film for
the first time, go to Step 4.
Use only Sharp Genuine
Supplies with this logo:
all.bookPage22Friday,May31,20029:49AM
Loading the Imaging Film
23
1. Installation
4 Remove the new roll of imaging film
from its packaging.
• Cut the band that holds the rolls
together.
5 Insert the green gears.
6 Insert the film into the print
compartment.
7 Rotate the front gear as shown until
the film is taut.
8 Close the operation panel (press down
on both sides to make sure it clicks
into place).
Fit ends of rolls
onto hubs
Make sure the
gears fit into the
slots in the ends
of the rolls.
1 slot
2 slots
Thick roll
to rear
all.bookPage23Friday,May31,20029:49AM
Loading Printing Paper
24
1 Fan the paper, and then tap the edge
against a flat surface to even the stack.
Make sure the stack edges are even.
2 Insert the stack of paper into the tray, PRINT SIDE DOWN.
• If paper remains in the tray, take it out and combine it into a single stack
with the new paper.
• Be sure to load the paper so that printing takes place on the print side of
the paper. Printing on the reverse side may result in poor print quality.
• GENTLY LOAD PAPER INTO THE PAPER TRAY.
• DO NOT FORCE IT DOWN INTO THE FEED SLOT.
Note: Do not use paper that has already been printed on, or paper that is curled.
Loading Printing Paper
You can load letter or legal size paper in the paper tray. Recommended paper
weight is 20-lb. Copy Bond. The maximum number of sheets is as follows:
Letter size:
Approx. 50 sheets (20-Ib. copier paper at room temperature;
maximum stack height should not be higher than the line on the
tray)
Legal size: 5 sheets
Note: If at any time the display shows the
alternating messages at right, check the printing
paper. If the tray is empty, add paper. If there is
paper in the tray, take it out and then reinsert it.
When you are finished, press
.
START/MEMORY
ADD PAPER &
PRESS START KEY
The stack
should not
be higher
than this line
all.bookPage24Friday,May31,20029:49AM
Loading Printing Paper
25
1. Installation
1 Press once and once.
2 Press once and twice.
3 Press once.
4 Select the paper size:
LETTER: LEGAL:
5 Press to return to the date and time display.
FUNCTION
1
2
STOP
Print contrast setting
Your fax has been set at the factory to print at normal contrast. If desired, you
can change the print contrast setting to LIGHT.
The display briefly shows
your selection, then:
1 Press once and once.
2 Press once and 3 times.
3 Press once.
4 Select the print contrast:
NORMAL: LIGHT:
5 Press to return to the date and time display.
FUNCTION
1
2
STOP
Display:
The display briefly shows
your selection, then:
PAPER SIZE SET
COPY CUT-OFF
OPTION SETTING
PRINT CONTRAST
PAPER SIZE SET
1=LETTER,2=LEGAL
1:NORMAL
Display:
OPTION SETTING
Setting the paper size
The fax has been set at the factory to scale received faxes to letter size paper.
If you loaded legal paper, you must change the paper size setting to LEGAL.
all.bookPage25Friday,May31,20029:49AM
Entering Your Name and Fax Number
26
Entering Your Name and Fax Number
Once you enter this
information, it will
automatically appear at
the top of each fax page
you send.
Before you can begin sending
faxes, you must enter your
name and fax (telephone)
number. You also need to set
the date and time.
FUNCTION
START/MEMORY
STOP
Important!
FCC regulations require that your name, telephone/fax number, and the date and
time appear on each fax message you send. Enter your name and fax number
here and set the date and time as explained in the following section to have the fax
machine include this information automatically at the top of your fax messages.
1 Press once and 3 times.
2 Press once.
3 Press once.
FUNCTION
1
9
4
5 6
7
8
0
2 3
Display:
ENTER FAX #
ENTRY MODE
OWN NUMBER SET
all.bookPage26Friday,May31,20029:49AM
Entering Your Name and Fax Number
27
1. Installation
4 Enter your fax number by pressing the number keys (max. 20 digits).
• To insert a space between digits, press .
• To clear a mistake, press .
5 Press to enter the fax number in memory.
6 Enter your name by pressing number keys for each letter as shown in
the chart below. Up to 24 characters can be entered.
Example: SHARP = 7777 44 2 777 7
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
♦ To clear a mistake, press .
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears. To enter one of the following symbols, press
or repeatedly: . / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | }
) (
7 Press .
8 Press to return to the date and time display.
SPEAKER
START/MEMORY
SPEAKER
START/MEMORY
STOP
Display:
DATE&TIME SET
A =
B =
C =
D =
E =
F =
G =
H =
I =
J =
K =
L =
M =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
X =
Y =
Z =
SPACE =
all.bookPage27Friday,May31,20029:49AM
Setting the Date and Time
28
Setting the Date and Time
1 Press once and 3 times.
2 Press once and once.
3 Press .
4 Enter a two-digit number for the month (“01” for January, “02” for
February, “12” for December, etc.).
Example: January
• To correct a mistake, press to move the cursor back to the mistake and
then enter the correct number.
5 Enter a two-digit number for the day (“01” to “31”).
Example: the 5
th
FUNCTION
0 1
0 5
The date and time appear
in the display and are
printed at the top of every
page you fax. Set the date
and time as shown below.
FUNCTION
STOP
1
9
4
5 6
7
8
0
2 3
Display:
The currently set date
appears (example):
ENTRY MODE
DATE&TIME SET
DATE 08-15-2002
DATE 01-15-2002
DATE 01-05-2002
START/MEMORY
all.bookPage28Friday,May31,20029:49AM
Setting the Date and Time
29
1. Installation
1 Press once and once.
2 Press once and 5 times.
3 Press once.
4 Press to select YES, or to select NO.
5 Press to return to the date and time display.
FUNCTION
1
2
STOP
Daylight Saving Time
If desired, you can set the clock to move forward and backward automatically
at the beginning and end of Daylight Saving Time. Follow these steps:
6 Enter the year (four digits).
Example: 2002
7 Enter a two-digit number for the hour (“01” to “12”) and a two-digit
number for the minute (“00” to “59”).
Example: 9:25
8 Press to select A.M. or to select P.M.
9 Press to start the clock.
10 Press to return to the date and time display.
2
0 0
2
0 9
2
5
START/MEMORY
STOP
The currently set time
appears (example):
TIME 12:19 PM
TIME 09:25 PM
ANTI JUNK #
RECEIVE RATIO
OPTION SETTING
DAY LIGHT SAVE
1=YES, 2=NO
all.bookPage29Friday,May31,20029:49AM
Setting the Reception Mode
30
Setting the Reception Mode
Your fax has three modes for receiving incoming faxes:
FAX mode:
Select this mode when you only want to receive faxes on your line. The fax
machine will automatically answer all calls on four rings and receive incoming
faxes.
TEL mode:
Select this mode when you want to receive both phone calls and faxes on the
line connected to the fax machine. All calls, including faxes, must be
answered by picking up the fax machine's handset or an extension phone
connected to the same line.
TAD mode:
Select this mode when you go out and want the answering system to answer
all calls. Voice messages will be recorded, and fax messages will be received
automatically (“TAD ” stands for “Telephone Answering Device”.)
Setting the reception mode
Make sure a document is not loaded in the document feeder, and then
press until the arrow in the display points to the desired mode.
RESOLUTION/
RECEPTION MODE
Note: TAD mode cannot be selected unless a general outgoing message has
been recorded as explained on page 48.
For more information on receiving faxes in FAX and TEL modes, see Chapter
5, Receiving Faxes. For more information on using TAD mode, see Chapter 3,
Using the Answering System.
FAX
TEL
JAN-02 10:30
FAX
TEL
JAN-02 10:30
FAX
TEL
JAN-02 10:30
TAD
TAD
TAD
1
9
4
5 6
7
8
0
2 3
RESOLUTION/
RECEPTION MODE
RESOLUTION/
RECEPTION MODE
all.bookPage30Friday,May31,20029:49AM
Volume Adjustment - Fax Machine
31
1. Installation
Volume Adjustment - Fax Machine
1 Press .
2 Press or to select the desired volume level.
• Press again to turn off the speaker.
SPEAKER
SPEAKER
Speaker
1
9
4
5 6
7
8
0
2 3
SPEAKER
1 When talking through the handset,
press or to select the desired
volume level.
• Note: The volume reverts to MIDDLE
each time you replace the handset.
Display:
Fax machine handset
RECEIVER: HIGH
RECEIVER: MIDDLE
RECEIVER: LOW
You can adjust the volume
of the speaker, handset,
and ringer using the up
and down arrow keys.
all.bookPage31Friday,May31,20029:49AM
Volume Adjustment - Cordless Handset
32
1 Press or to select the desired
volume level.
(Make sure has not been
pressed, the handset is not lifted, and a
document is not loaded in the feeder.)
• The ringer rings once at the selected
level, and then the date and time
reappear in the display.
2 If you selected “RINGER: OFF OK ?” to
turn off the ringer, press .
SPEAKER
START/MEMORY
Fax machine ringer
Display:
RINGER: HIGH
RINGER: MIDDLE
RINGER: LOW
RINGER: OFF OK ?
Volume Adjustment - Cordless Handset
You can adjust the volume
of the ringer and handset,
receiver using the up and
down arrow keys.
all.bookPage32Friday,May31,20029:49AM
Volume Adjustment - Cordless Handset
33
1. Installation
Cordless handset ringer
1 When you are not talking on the
cordless handset, press or to
select the desired ringer volume level.
• The ringer will ring once at the selected
level.
2 If you selected “RINGER: OFF OK ?” to
turn off the ringer, press .
START
RINGER: HIGH
Cordless handset display:
RINGER: MIDDLE
RINGER: LOW
RINGER: OFF OK ?
OK: PRESS START
1 When talking on the cordless handset,
press or to select the desired
volume level.
• Note: The volume reverts to MIDDLE
each time you hang up (press ).
OFF
OFF
RECEIVER: HIGH
Cordless handset display:
RECEIVER: MIDDLE
RECEIVER: LOW
Cordless handset receiver volume
all.bookPage33Friday,May31,20029:49AM
34
2. Using the Cordless Handset
Making a Phone Call
1 Pick up the cordless handset and
press .
2 When you hear the dial tone, dial the
number.
3 When you are ready to end the call, press .
• You can also end the call by simply placing the cordless handset in the
charger.
TALK
OFF
OFF
TAL K
Cordless handset display:
TALK
OFF
OFF
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
RECEPTION
TUV
8
WXYZ
9
PLAY
PLAY NEW
0
STOP
REPEAT SKIP DELETE
If the display shows FAX BUSY,
you must wait until the fax
machine is no longer in use to
use the cordless handset.
all.bookPage34Friday,May31,20029:49AM
Receiving a Phone Call
35
2. Cordless
Handset
Receiving a Phone Call
1 When the cordless handset rings, pick it up and press any key (except
) to answer. Talk to the other party.
• If the cordless handset is in the charger, simply pick it up to answer (you do
not need to press a key).
2 When you are ready to end the call, press .
• You can also end the call by simply placing the cordless handset in the
charger.
OFF
OFF
OFF
OFF
Putting a Call on Hold
To put the other party on hold during a call, press . The cordless handset
will beep while the call is on hold. When you are ready to resume the call,
press once again. Note that placing the cordless handset in the charger
will not break the connection while a call is on hold, and thus phone charges
may continue to apply.
HOLD
HOLD
You can also dial by entering the phone
number first and then pressing .
TALK
Check the number in the display before pressing . If there is a mistake,
press to clear the mistake and then enter the correct digits.
Note: If a pause is needed between any of the digits to access an outside
line or a special service, press . The pause will appear as a hyphen (-).
TALK
ERASE
HOLD
FUNCTION
/PAUSE
all.bookPage35Friday,May31,20029:49AM
Receiving a Fax Using the Cordless Handset
36
START
Press to begin
fax reception
Note: If the fax machine detects a fax signal after you answer a call on the
cordless handset, it will begin reception automatically.
Receiving a Fax Using the Cordless Handset
If you hear a fax tone after answering a call on the cordless handset, or if the
other party speaks to you and then wants to send a fax, press . This
signals the fax machine to begin fax reception.
START
Storing and Using Auto-Dial Numbers
You can store your most frequently dialed numbers for automatic dialing.
Numbers can be stored in the Common book or the Private book.
♦ Up to 40 numbers can be stored in the Common book. These numbers are
shared with the fax machine and other cordless handsets, and can be
stored using a cordless handset as explained below, or the fax machine as
explained on page 74.
♦ Up to 5 numbers can be stored in the Private book. Each cordless handset
has its own Private book, and the numbers are stored using the cordless
handset as explained below.
1 Press .
2 Press to select the Common book,
or to select the Private book.
SEARCH
Cordless handset display:
SELECT SEARCH
▲: COMMON
▼: PRIVATE
COMMON DIAL
▲▼: SEARCH
FUNCTION: ENTRY
Example: Common book selected
all.bookPage36Friday,May31,20029:49AM
Storing and Using Auto-Dial Numbers
37
2. Cordless
Handset
3 Press .
4 Enter the number by pressing the number keys.
(Note: A space cannot be entered.)
• To clear a mistake, press .
• If a pause is required between any of the digits to access a special service
or an outside line, press . The pause appears as a hyphen (two
seconds per pause). Several pauses can be entered in a row.
5 Press .
6 Enter a name by pressing number keys for each letter as shown in the
chart below. Up to 15 characters can be entered. (If you do not wish to
enter a name, go directly to Step 7.)
Example: SHARP = 7777 44 2 777 7
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
♦ To clear a mistake, press .
FUNCTION
/PAUSE
ERASE
HOLD
FUNCTION
/PAUSE
START
ERASE
HOLD
A =
B =
C =
D =
E =
F =
G =
H =
I =
J =
K =
L =
M =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
X =
Y =
Z =
SPACE =
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
TUV
8
TUV
8
TUV
8
TUV
8
TUV
8
TUV
8
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
MNO
6
MNO
6
MNO
6
MNO
6
MNO
6
JKL
5
JKL
5
JKL
5
MNO
6
JKL
5
JKL
5
JKL
5
GHI
4
GHI
4
GHI
4
GHI
4
GHI
4
GHI
4
DEF
3
DEF
3
DEF
3
DEF
3
DEF
3
DEF
3
ABC
2
ABC
2
ABC
2
ABC
2
ABC
2
ABC
2
1
ENTER TEL #
all.bookPage37Friday,May31,20029:49AM
Storing and Using Auto-Dial Numbers
38
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears.
♦ To enter one of the following symbols, press or repeatedly:
. / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | }
) (
7 Press .
8 Return to Step 2 to store another number, or press to exit.
START
OFF
OFF
Dialing an auto-dial number
1 Press once.
2 Press to select the Common book,
or to select the Private book.
3 Press or until the number you wish to dial appears in the
display.
4 Press .
• The number is automatically dialed.
SEARCH
TALK
COMMON DIAL
▲▼: SEARCH
FUNCTION: ENTRY
Example: Common book selected
SELECT SEARCH
▲: COMMON
▼: PRIVATE
Cordless handset display:
SELECT SEARCH
▲: COMMON
▼: PRIVATE
all.bookPage38Friday,May31,20029:49AM
Storing and Using Auto-Dial Numbers
39
2. Cordless
Handset
Editing an auto-dial number
If you need to make changes to a previously stored auto-dial number, follow
these steps:
1 Press once.
2 Press to select the Common book,
or to select the Private book.
3 Press or until the number you wish to edit appears in the
display.
4 Press once.
5 Press the number keys to enter the new number.
• To clear a mistake, press . If a pause is required between any of the
digits to access a special service or an outside line, press .
• If you do not wish to change the number, go directly to Step 6.
6 Press .
7 Press the number keys to enter the new name (see Step 6 on page 37).
• If you do not wish to change the name, go directly to Step 8.
8 Press .
SEARCH
FUNCTION
/PAUSE
ERASE
HOLD
FUNCTION
/PAUSE
START
START
COMMON DIAL
▲▼: SEARCH
FUNCTION: ENTRY
Example: Common book selected
Cordless handset display:
SELECT SEARCH
▲: COMMON
▼: PRIVATE
SELECT SEARCH
▲: COMMON
▼: PRIVATE
all.bookPage39Friday,May31,20029:49AM
Storing and Using Auto-Dial Numbers
40
Clearing an auto-dial number
If you need to clear an auto-dial number, follow these steps:
1 Press once.
2 Press to select the Common book,
or to select the Private book.
3 Press or until the number you wish to clear appears in the
display.
4 Press .
5 Press .
6 Press to exit.
SEARCH
ERASE
HOLD
START
OFF
OFF
COMMON DIAL
▲▼: SEARCH
FUNCTION: ENTRY
Example: Common book selected
ERASE?
PRESS START KEY
9 Press to exit.
OFF
OFF
SELECT SEARCH
▲: COMMON
▼: PRIVATE
Cordless handset display:
SELECT SEARCH
▲: COMMON
▼: PRIVATE
all.bookPage40Friday,May31,20029:49AM
Redial
41
2. Cordless
Handset
Redial
You can automatically redial the last number dialed on the cordless handset.
Note: The fax machine and cordless handsets each retain their own separate
redial numbers. Note that the cordless handset redial numbers will be lost if
the fax machine is unplugged or an interruption occurs in the power supply.
1 Press .
• Check the display to make sure the number that appears is the number you
wish to dial. (If the wrong number appears, press to clear it.)
2 Press . The number is automatically dialed.
Note: You can also redial by pressing first and then . Note that this
method does not allow you to check the number before dialing begins.
REDIAL
OFF
OFF
TALK
TALK
REDIAL
Using the Intercom Feature
♦ When using the Intercom feature, you will not hear your voice through the
handset receiver when you speak.
♦ It may not be possible to page another cordless handset or the fax machine
when other cordless handsets or the fax machine are already in use.
Paging the fax machine from a cordless handset
You can use the fax
machine and cordless
handsets as an
intercom system.
1 Press on the cordless handset.
INTER
COM
2: BILL
3: SUE
4:
Cordless handset
display example:
The numbers and names of the other cordless
handsets appear (even the numbers of cordless
handsets that are not registered)
all.bookPage41Friday,May31,20029:49AM
Using the Intercom Feature
42
2 Press on the cordless handset to
select the fax machine.
3 The fax machine rings.
4 The other person picks up the fax machine handset to answer.
5 Talk with the other person. When you are ready to end the conversation,
press .
0
OFF
OFF
INTERCOM
0: BASE STATION
Cordless handset display:
Fax machine display:
INTERCOM
1: BOB
Number and name
of calling handset
Paging a cordless handset from another cordless handset
(walkie-talkie feature)
The cordless handsets can be used for walkie-talkie like communication The
talking range of the cordless handsets is ???? ft. (??? m), and there is no
need to be in the talking range of the fax machine.
1 Press on the cordless handset.
2 Enter the number of the cordless
handset that you wish to page.
Example:
• To page all cordless handsets and the fax machine, press .
INTER
COM
ABC
2
2: BILL
3: SUE
4:
Cordless handset
display example:
The numbers and names of the other cordless
handsets appear (even the numbers of cordless
handsets that are not registered)
INTERCOM
2: BILL
all.bookPage42Friday,May31,20029:49AM
Using the Intercom Feature
43
2. Cordless
Handset
Paging a cordless handset from the fax machine
(cordless handset locator)
You can use this procedure to page a cordless handset, or locate a handset in
the event that you misplace it.
1 Pick up the fax machine handset.
2 Press on the fax machine, and
enter the number of the cordless
handset that you wish to page.
Example:
• To page all of the cordless handsets, press .
3 The selected cordless handset rings.
• This allows you to locate the cordless
handset if you have misplaced it.
4 The other person presses any key (except ) on the cordless
handset to answer.
INTERCOM
3
OFF
OFF
3 The selected cordless handset rings.
4 The other person presses any key (except ) on the cordless
handset to answer.
5 Talk with the other person. When you are ready to end the conversation,
press .
OFF
OFF
OFF
OFF
INTERCOM
0: BASE STATION
Fax machine display:
INTERCOM
3: SUE
Display of selected
cordless handset:
INTERCOM
1: BOB
Display of paged handset:
Number and name
of calling handset
all.bookPage43Friday,May31,20029:49AM
Transferring Calls
44
Transferring Calls
You can transfer a call to the fax machine or to a cordless handset.
Note: It is not possible to talk to the recipient of a transfer call before
transferring.
Transferring a call from a cordless handset to the fax
machine or to another cordless handset
1 During the call, press on the
cordless handset.
• The call is placed on hold.
2 To transfer the call to the fax machine,
press .
To transfer the call to a cordless
handset, enter the number of the
handset.
• To page the fax machine and all
cordless handsets, press
INTER
COM
0
If a call comes in while the Intercom feature is being used
If an outside call comes in while you are using the Intercom feature, the
person who wishes to take the call should first stop the Intercom call (press
on the cordless handset or replace the fax machine handset), and then
answer the outside call (press any key except on the cordless handset
or pick up the fax machine handset).
OFF
OFF
OFF
OFF
5 Talk with the other person. When you are ready to end the conversation,
replace the handset.
2: BILL
3: SUE
4:
Cordless handset
display example:
The numbers and names of the other cordless
handsets appear (even the numbers of
cordless handsets that are not registered)
CALL TRANSFER
The fax machine and cordless
handsets all show the above
message, regardless of which
is selected.
CALL
TRANSFER
all.bookPage44Friday,May31,20029:49AM
Transferring Calls
45
2. Cordless
Handset
3 The selected cordless handset or fax machine rings.
4 The other person answers on the cordless handset or fax machine.
• To answer on a cordless handset other than the selected cordless handset,
press on that cordless handset. To answer on the fax machine when
not selected, pick up the fax machine handset.
• If nobody answers for one minute when you page the cordless handset or
fax machine, your cordless handset will ring to alert you. Press to
return to the initial caller. (Note that if you take no action after your cordless
handset rings, the initial caller will be disconnected.)
TALK
TALK
Transferring a call from the fax machine to a cordless
handset
1 During the call, press on the
fax machine.
• The call is placed on hold.
2 Enter the number of the cordless
handset to which you wish to transfer
the call.
Example: .
• To page all of the cordless handsets,
press .
INTERCOM
3
Fax machine display:
REPLACE HANDSET
PRESS HANDSET #
This message alternates with
the numbers and names of
the cordless handsets
Fax machine display:
all.bookPage45Friday,May31,20029:49AM
Transferring Calls
46
3 Replace the fax machine handset. The
selected cordless handset rings.
4 The other person presses any key (except ) on the cordless
handset to answer.
• To answer on a cordless handset other than the selected cordless handset,
press on the other cordless handset.
• If no one answers for one minute when you page the cordless handset, the
fax machine will ring to alert you. Pick up the fax machine handset to return
to the initial caller. (Note that if you take no action after the fax machine
rings, the initial caller will be disconnected.)
OFF
OFF
TALK
CALL TRANSFER
Displays of all
cordless handsets
Fax machine display:
CALL
TRANSFER
Changing the reception mode on the fax machine
1 Press .
2 Press until the desired reception
mode appears in the display.
3 Press or to exit REMOTE MODE.
REMOTE
/FLASH
JKL
5
RECEPTION
REMOTE
/FLASH
OFF
OFF
RECEPTION
FAX
Example: FAX mode
REMOTE MODE
Cordless handset display:
Note: When a cordless handset is paged, it will continue ringing until the
paging is answered, even if is pressed on the cordless handset or the
cordless handset is placed in the charger.
OFF
OFF
all.bookPage46Friday,May31,20029:49AM
47
3. Answering
Machine
3. Using the Answering System
The answering system allows you to receive both voice messages and faxes
while you are out.
The answering system
has one general box
and four personal
boxes for callers to
leave messages.
To use the answering system,
you must record a greeting for
the general box, and a
greeting for each personal box
you wish to use.
Each cordless handset can be used to listen to the
messages in its corresponding personal box (the
personal box with the same number as the cordless
handset).
(A personal box can still be used even if you do not
have the corresponding accessory cordless handset.)
1
2
3
4
General
Box
Personal Box
1234
Press
General
Message
Personal
Message
1
2 3
4
all.bookPage47Friday,May31,20029:49AM
Recording an Outgoing Message
48
Recording an Outgoing Message
The outgoing message (OGM) is the greeting that the system plays after
answering a call to inform callers that they can leave a message or send a fax.
Follow the steps below to record an outgoing message for the general box,
and an outgoing message for each personal box that you wish to use.
Example of general outgoing message:
“Hello. You've reached ______ . No one is available to take your call right now.
If you would like to leave a general message, please speak after the beep. If
you would like to leave a personal message, press 1 for Susan, 2 for Bob, 3
for George, or 4 for Ann now. To send a fax, please press your facsimile Start
key now. Thank you for calling.”
Example of personal outgoing message:
“This is Susan’s personal box. Please leave a message after the beep.”
Note: Do not lift the handset until Step 3 below.
1 Press .
2 Press until the message you wish
to record appears in the display.
(“OGM (GENERAL)” for the general
box, “OGM (BOX 1)” for personal box 1,
“OGM (BOX 2) for personal box 2, etc.)
3 Press once.
• (If you have already recorded a
message and wish to check it,
press .)
REC/
MEMO
PLAY
Display:
MEMO RECORDING
MEMO RECORDING
OGM (GENERAL)
OGM (BOX 1)
OGM (BOX 4)
OGM (TRANSFER)
Note: MEMO RECORDING is for recording a
memo (page 53), and OGM (TRANSFER) is
for the Transfer function (page 59).
LIFT HANDSET OR
PLAY: PLAYBACK
all.bookPage48Friday,May31,20029:49AM
Setting a Passcode for a Personal Box
49
3. Answering
Machine
4 Lift the handset.
5 Press and speak into the handset to record the message.
• While recording, the display will show the time left to record.
6 When finished, replace the handset or press .
START/MEMORY
STOP
To listen to an outgoing message
To listen to an outgoing message, follow Steps 1 and 2 of the above
procedure and then press . Note that the general outgoing message
cannot be erased. If you need to change it, simply repeat the recording
procedure.
Setting a Passcode for a Personal Box
You can set a 3-digit passcode for each personal box. When this is done, the
passcode must be entered to listen to messages in a personal box at the fax
machine.
(Note: When listening to the messages in a personal box from its
corresponding cordless handset, is not necessary to enter the passcode. )
PLAY
1 Press once and once.
2 Press once and once.
3 Press .
FUNCTION
BOX PASSCODE
Display:
T.A.D. SETTING
1=SET, 2=CLEAR
all.bookPage49Friday,May31,20029:49AM
Operating the Answering System
50
4 Press to set a passcode.
(To clear a previously set passcode,
press .)
5 Enter the number of the personal box
for which you wish to set a passcode.
Example: for Box 1
(If you are clearing a passcode, enter
the number of the box and go to Step
7.)
6 Enter a 3-digit number for the passcode. The first digit of the number
must be 0, 5, 6, 7, 8, or 9.
7 Press .
8 Return to Step 5 to set another passcode, or press to return to
the date and time display.
1
2
1
START/MEMORY
STOP
ENTER PASSCODE
Note: If you wish to change a passcode, clear the passcode and then enter a
new passcode. If you forget a passcode, clear it and enter a new passcode.
ENTER BOX # (1-4)
Operating the Answering System
Activating the answering system
To turn on the answering system so that callers can leave messages, press
until the arrow in the display points to TAD. (TAD stands for
“Telephone Answering Device”.)
RESOLUTION/
RECEPTION MODE
RESOLUTION/
RECEPTION MODE
FAX
TEL
TAD
ENTER BOX # (1-4)
all.bookPage50Friday,May31,20029:49AM
Operating the Answering System
51
3. Answering
Machine
♦ Each outgoing message will play (to stop playback, press ).
♦ It will not be possible to set the reception mode to TAD if a general outgoing
message has not been recorded.
Note: In TAD mode, the machine will automatically switch to fax reception if it
detects 6 seconds of silence after answering a call. For this reason, if a caller
pauses for this length of time while leaving a message, they will be cut off.
Number of rings in TAD mode (Toll Saver function)
The number of rings on which the machine answers incoming calls in TAD
mode depends on whether the Toll Saver function is turned on, and if it is on,
whether you have messages.
♦ The Toll Saver function is initially turned on.
STOP
To adjust the
NUMBER OF RINGS
setting, see page 83.
To turn off the Toll Saver
function, see page 63.
ON
OFF
No received messages
4 Rings
Received messages
2 Rings
Toll Saver Toll Saver
NOTHING
Hello!
Hi!
Hi!
Ring
Ring
R
ing
Ring
Ring
R
ing
Ring
Ring
R
ing
Ring
(Answer according to
NUMBER OF RINGS setting)
all.bookPage51Friday,May31,20029:49AM
Operating the Answering System
52
Listening to received messages (at the fax machine)
When you return, the fax machine display will show the number of messages
recorded in each box. Follow the steps below to listen to your messages.
1 Press .
• If you only want to listen to new messages (messages not previously
listened to), continue to hold down for at least two seconds.
2 If you wish to listen to the messages in a personal box, press the
number of the box.
Example: for Box 1
3 Enter the passcode of the personal box.
Example:
4 The messages will play.
• As each message plays, the date and time of recording will appear briefly in
the display. If no messages were received, NO MESSAGES will appear.
• Repeat: To listen to a message a second time, press before
playback of that message ends. To move back to the previous message,
press within 3 seconds of the beginning of the current message.
• Skip: To skip forward to the next message, press .
PLAY
PLAY
1
5 5 1
REPEAT
REPEAT
SKIP
0
Note: Playback will stop if you receive a call, lift the handset, or press .
♦ You can print out a list of your received messages that shows the date and
time that each was received. See page 99.
STOP
all.bookPage52Friday,May31,20029:49AM
Operating the Answering System
53
3. Answering
Machine
Erasing received messages
It is important to erase received messages after you listen to them to ensure
that the memory does not become full.
♦ Erasing all messages in the general box: To erase all messages in the
general box, press , , and then .
♦ Erasing all messages in a personal box: To erase all messages in a
personal box, press , , enter the number of the box, enter the
passcode, and then press .
♦ Erasing a single message: To erase a single message, press
while the message is being played.
FUNCTION
DELETE
START/MEMORY
FUNCTION
DELETE
START/MEMORY
DELETE
Recording memos
You can record memos for yourself and other users of the machine. These
are recorded in the general box, and will be played back together with
incoming messages when the key is pressed.
PLAY
1 Press once and once.
2 Pick up the handset, press , and speak into the handset.
3 When you have finished speaking, replace the handset or press .
REC/
MEMO
START/MEMORY
STOP
all.bookPage53Friday,May31,20029:49AM
Operating the Answering System
54
Recording phone conversations
To record a phone conversation, hold down the key during the
conversation you want to record. When you are finished, release the key. The
conversation is recorded in the general box, and will be played back when the
key is pressed.
REC/
MEMO
PLAY
Listening to messages from a cordless handset
You can use your cordless handset to listen to messages received in your
personal box (the personal box with the same number as your cordless
handset), or messages received in the general box.
♦ When you have received new messages in your personal box, NEW
MESSAGES appears in your cordless handset display.
1 Press .
2 If you wish to listen to messages in the general box, press .
(Otherwise, go directly to Step 3.)
3 Press to listen to all messages in the box, or to listen to only
new messages.
4 While listening to your messages, you can do any of the following:
• Repeat: To repeat a message, press .
• Skip: To skip forward, press .
• Delete: To delete the message you are currently listening to, press .
REMOTE
/FLASH
0
PQRS
7
PLAY
TUV
8
PLAY NEW
REPEAT
0
SKIP
DELETE
REMOTE MODE
Cordless handset display:
all.bookPage54Friday,May31,20029:49AM
Operating the Answering System
55
3. Answering
Machine
• Stop: To stop playback, press .
5 To return to the STAND-BY display, press or .
• If a call comes in while you are listening to your messages, playback will
stop automatically. Press any key to answer.
• If you take no action for 60 seconds in REMOTE MODE, the cordless
handset will automatically return to the STAND-BY display.
STOP
WXYZ
9
OFF
OFF
REMOTE
/FLASH
Deleting all messages from a cordless handset
You can use your cordless handset to delete all messages in your personal
box, or all messages in the general box.
1 Press .
(Note: This step is not necessary if you
are already in REMOTE MODE.)
2 If you wish to delete all messages in the general box, press .
(Otherwise, go directly to Step 3.)
3 Press .
4 Press to delete the messages, and then or to return to
the STAND-BY display.
• To cancel, press , , or .
REMOTE
/FLASH
0
DELETE
START
OFF
OFF
REMOTE
/FLASH
STOP
WXYZ
9
OFF
OFF
REMOTE
/FLASH
REMOTE MODE
Cordless handset display:
REMOTE MODE
DELETE ALL?
PRESS START KEY
all.bookPage55Friday,May31,20029:49AM
Optional Answering System Settings
56
1 Press once and once.
2 Press once and once.
3 Press .
4 Press a number from 1 to 4 to select the desired ICM recording time.
5 Press to return to the date and time display.
15 seconds 60 seconds
30 seconds 4 minutes
FUNCTION
STOP
Optional Answering System Settings
Setting ICM time
Incoming messages (ICMs) are the messages which callers leave for you in
the answering system. The answering system is set at the factory to allow
each caller a maximum of 4 minutes to leave a message. If desired, you can
change this setting to 15, 30, or 60 seconds.
Display:
T.A.D. SETTING
RECORDING TIME
1
2
3
4
The display briefly shows
your selection, then:
REMOTE CODE
Fax reception on TAD failure
If the memory for recording incoming messages becomes full while you are
out, the answering system will no longer be able to record messages. The ON
TAD FAILURE setting is used to choose the response of the machine to
incoming calls when this happens:
♦ Automatic fax reception NO: The machine will answer after 20 rings, after
which it will wait to receive a remote command. Most callers will hang up
before it answers; however, when you call the machine from a remote
location, you can wait until it answers, listen to your messages, and then
erase them (see Remote Operations on page 62).
all.bookPage56Friday,May31,20029:49AM
Optional Answering System Settings
57
3. Answering
Machine
1 Press once and once.
2 Press once and 4 times.
3 Press .
4 Press to turn on automatic fax
reception, or to turn it off.
5 Press to return to the date and time display.
FUNCTION
1
2
STOP
ON TAD FAILURE
♦ Automatic fax reception YES: The reception mode will switch to FAX mode,
allowing the machine to continue to receive faxes automatically. With this
setting, you can still use the remote commands to listen to your messages
and then erase them (see Remote Operations on page 62).
Automatic fax reception is set to NO at the factory before shipping. If you want
to set it to YES, press the panel keys as follows:
Display:
T.A.D. SETTING
1=YES, 2=NO
The display briefly shows
your selection, then:
OGM ONLY MODE
OGM only mode
If needed, you can turn off recording of incoming messages. In this case, your
outgoing message will play, but callers will not be able to leave a message
(this applies to all boxes). The machine will still receive faxes sent by
automatic dialing.
1 Press once and once.
2 Press once and 3 times.
FUNCTION
OGM ONLY MODE
Display:
T.A.D. SETTING
all.bookPage57Friday,May31,20029:49AM
Optional Answering System Settings
58
3 Press .
4 Press to turn on OGM only mode,
or to turn it off.
5 Press to return to the date and time display.
1
2
STOP
The display briefly shows
your selection, then:
CPC DETECTION
CPC Detection
When a caller hangs up, the central telephone exchange issues a CPC
(Calling Party Control) signal. When the answering system detects this signal,
it stops recording so that periods of silence are not recorded.
However, if you subscribe to special services such as Call Waiting or Call
Forwarding, signals used by these services may be mistaken for a CPC
signal, causing the answering system to hang up during a call. If you
experience this problem, follow these steps to turn off CPC Detection.
1 Press once and once.
2 Press once and twice.
3 Press .
4 Press to turn on CPC Detection,
or to turn it off.
5 Press to return to the date and time display.
FUNCTION
1
2
STOP
CPC DETECTION
Display:
T.A.D. SETTING
1=YES, 2=NO
The display briefly shows
your selection, then:
BOX PASSCODE#
1=YES, 2=NO
all.bookPage58Friday,May31,20029:49AM
Transfer Function
59
3. Answering
Machine
Transfer Function
The Transfer function is used to have the machine automatically call you at a
specified number every time it receives an incoming message in a specified
box. This lets you hear your messages immediately after they come in, even
when you are at a remote location.
To use the Transfer function, you must first program the number that you wish
the machine to call (the transfer number), and record the transfer message
that plays when you answer the phone at the remote location.
When you go out and wish to use the transfer function, turn it on. When you
return and no longer wish to use the transfer function, turn it off.
Programming the transfer number
To use the Transfer function, you must first give the machine the number to
call (the transfer number).
1 Press once and once.
2 Press once and 3 times.
3 Press .
4 Press the number keys to enter the transfer number.
• To insert a pause between any two digits of the number, press .
5 Press .
6 Press to return to the date and time display.
FUNCTION
FUNCTION
START/MEMORY
STOP
TRANSFER TEL #
Display:
T.A.D. SETTING
ENTER TEL #
all.bookPage59Friday,May31,20029:49AM
Transfer Function
60
Recording the transfer message
The transfer message plays when you answer the telephone, and informs you
that the call is a transfer call. The following is an example:
“Hello. This is a transfer call for (YOUR NAME). Enter your remote code
number now.”
Note: Do not lift the handset until Step 3 below.
1 Press once and once.
2 Press once.
• If you have already recorded a message, you can press to listen to the
message, or press to delete the message.
3 Lift the handset.
4 Press and speak into the handset to record the message.
• The transfer message can be up to 15 seconds long. While recording, the
display will show the time left to record.
5 When finished, replace the handset or press .
REC/
MEMO
PLAY
DELETE
START/MEMORY
STOP
Display:
OGM (TRANSFER)
Checking or erasing the transfer message
To check or erase the transfer message, follow Steps 1 and 2 of the above
procedure, and then press to check the message, or to erase the
message.
PLAY
DELETE
all.bookPage60Friday,May31,20029:49AM
Transfer Function
61
3. Answering
Machine
Turning the Transfer function on and off
When you go out and wish to use the Transfer function, turn it on as follows:
1 Press once and once.
2 Press once and 4 times.
3 Press .
4 Press to turn on the Transfer
function.
(Press to turn the function off.)
5 Press the number of the box for which you want the Transfer function to
operate (for the general box, press ).
6 Press to return to the date and time display.
7 Each time the machine receives an incoming message, it will call your
programmed transfer number. When you answer, you will hear your
recorded message telling you that the call is a transfer call. On the dial
pad of your phone, enter , your remote code number (see page 62) if
the general box was selected in Step 5, or the box passcode number if a
personal box was selected, and then . Your messages will play.
• You can also perform any of the remote operations described in Remote
Operations later in this chapter (see page 62).
Note: When you hang up after a transfer call, the machine will not
immediately resume normal operation. If you want the machine to accept calls
immediately after a transfer call, enter twice before hanging up (if
hanging up during message playback, first enter and to stop
playback, then enter twice).
FUNCTION
1
2
0
STOP
0
TRANSFER FUNC
Display:
T.A.D. SETTING
1=YES, 2=NO
The display briefly shows
your selection, then:
ON TAD FAILURE
all.bookPage61Friday,May31,20029:49AM
Remote Operations
62
1 Press once and once.
2 Press once and twice.
3 Press .
4 Press the number keys to enter a 3-digit remote code number.
5 Press to store the remote
number.
6 Press to return to the date and time display.
FUNCTION
START/MEMORY
STOP
Remote Operations
When you are out, you can call the machine from any touch-tone telephone
and play back your messages using the remote commands. You can also use
these commands to change the reception mode and other settings.
Remote code number
After calling the machine, you must enter your remote code number to listen
to messages in the general box, or to messages in a personal box that does
not have a passcode.
The remote code number has been set to "001" at the factory. To change the
number, follow the steps below.
Display:
T.A.D. SETTING
REMOTE CODE
TRANSFER TEL #
all.bookPage62Friday,May31,20029:49AM
Remote Operations
63
3. Answering
Machine
Toll Saver
When you call the machine to listen to your messages, it will answer after two
rings if it has received at least one message in any of the boxes, or after four
rings if it has not received any messages.
This allows you to save money on telephone charges, particularly if you are
calling long distance. If the machine does not answer after the second ring,
you can simply hang up before it answers, saving yourself the cost of that call.
If you do not want to use the Toll Saver function, you can turn it off by
following the steps below. In this case, the machine will answer after the
number of rings set with the NUMBER OF RINGS setting (see Changing the
number of rings on page 83).
1 Press once and once.
2 Press once.
3 Press once.
4 Press to turn on the Toll Saver
function, or to turn it off.
5 Press to return to the date and time display.
FUNCTION
1
2
STOP
TOLL SAVER
Display:
T.A.D. SETTING
1=YES, 2=NO
The display briefly shows
your selection, then:
RECORDING TIME
all.bookPage63Friday,May31,20029:49AM
Remote Operations
64
Retrieving your messages
Note: You can only access one box per call. If you wish to access more than
one box, you must make a separate call for each box.
1 Call the machine from a touch-tone telephone. When the general
outgoing message begins, press on the telephone.
• You will hear a short beep, and the outgoing message will stop.
2 If you wish to listen to the messages in a personal box, enter the number
of that box (otherwise, go directly to Step 3).
Example: for Box 1
3 If you are accessing the general box, enter your remote code.
If you are accessing a personal box, enter the passcode of the box (if the
box does not have a passcode, enter your remote code).
When finished, press .
• You will hear a series of beeps equal to the number of messages recorded
in the box, or one long beep if four or more messages have been received.
The machine will then play back the messages, beeping once at the end of
each message. When all messages have been played back, you will hear a
long beep.
• If no messages have been received, you will hear a short beep. You can
either hang up, or perform any of the operations described in the following
section, Other remote operations.
1
all.bookPage64Friday,May31,20029:49AM
Remote Operations
65
3. Answering
Machine
4 While the messages are playing, you can do any of the following:
• Repeat: To listen to a message a second time, press and on the
telephone before that message ends. To move back to the previous
message, press and during the first 3 seconds of the current
message.
• Skip forward: To skip forward to the next message, press and
on the telephone.
• Stop: To stop playback, press and on the telephone. After this,
you can enter any of the commands described in the following section,
Other remote operations.
• Play new messages: To listen to only your new messages, first stop
playback by pressing and , and then press and .
• Erase a message: To erase the message you are currently listening to,
press and before it ends.
5 When you have finished listening to your messages, you can do any of
the following:
• Erase all messages: Press , , and .
• Repeat playback: Press and .
• Perform other operations: You can enter any of the commands described
in the following section, Other remote operations.
• Hang up: If you do not erase your messages first, they will be saved and
any new messages will be recorded after them. If you want the machine to
resume normal operation immediately, press twice before hanging up
(in some cases, particularly when the Transfer function is used, the
machine may not accept new calls for one or two minutes after you hang up
unless you press twice).
2
2
5
0
0 6
3
3 3
7
all.bookPage65Friday,May31,20029:49AM
Remote Operations
66
Note: You can also call the machine and perform remote operations when the
reception mode is set to FAX. In this case, when you call the machine, press
immediately after it answers (before you hear the fax tone), and then
continue from Step 2 above.
Comments:
♦ When a remote command is accepted by the machine, you will hear one
beep. If an incorrect command is entered, you will hear four beeps. In the
latter case, re-enter the correct command.
♦ When entering a command, do not pause longer than 10 seconds between
each digit. If you do, you will hear a 4-beep error signal and the digits
entered up to that point will be cleared. In this case, re-enter the command
from the beginning.
♦ If you pause for longer than 10 seconds before entering a command, or
make two errors while entering your remote code number, the line will be
disconnected. (This prevents unauthorized people from attempting to
guess your remote code number.)
Other remote operations
After listening to your messages, you can perform any of the following
operations by pressing the appropriate keys on the telephone.
Note: The following commands cannot be entered while messages are being
played back. If you do not want to wait until playback ends to enter a
command, first stop playback by pressing and , and then enter the
command.
Changing the fax reception mode
Select a new reception mode by pressing the keys as follows:
0
♦ TAD mode: , , and .
♦ FAX mode: , , and .
♦ TEL mode: , , and .
8 1
8
2
8 3
Caution: If you select TEL mode,
you will not be able to change the
reception mode again.
all.bookPage66Friday,May31,20029:49AM
Remote Operations
67
3. Answering
Machine
Recording a new outgoing message
Note: You can only record a new outgoing message for the box you accessed
at the beginning of the call.
1 Press and on the telephone.
2 When you hear a short beep, speak into the telephone to record the new
message.
• The message can be up to 15 seconds long. After 15 seconds (or earlier if
the machine detects silence after you finish speaking), you will hear a
beep, and the new message will be played back.
4
Turning the Transfer function on or off
To turn Transfer on: Press , , and on the telephone, followed
by the number of the box for which you want the Transfer function to operate
(press for the general box) and .
To turn Transfer off: Press , , and on the telephone.
9 1
0
9
2
Changing the transfer telephone number
1 Press , , and on the telephone.
2 After you hear a short beep, enter the new telephone number. When
finished, press .
• To insert a pause between any two digits of the number, press .
9 0
all.bookPage67Friday,May31,20029:49AM
Remote Operations
68
Recording a memo
You can record a memo for yourself or other users of the machine. The memo
will be recorded in the general box.
1 Press and on the telephone.
2 When you hear a short beep, speak into the telephone to record the
memo.
3 When you are finished, press and on the telephone.
• If the machine detects silence, it will stop recording automatically.
0
Recording a new transfer message
1 Press , , and on the telephone.
2 When you hear a short beep, speak into the telephone to record the new
message.
• The time for the transfer message is fixed at 15 seconds. After 15 seconds
(or earlier if the machine detects silence after you finish speaking), you will
hear a beep, and the new message will be played back automatically.
9 3
OGM only mode
To turn on OGM only mode: Press , , and on the telephone.
(Outgoing messages will play, but callers will not be able to record a
message. Faxes sent by automatic dialling will be received)
To turn off OGM only mode: Press , , and on the telephone.
1 1
1
2
all.bookPage68Friday,May31,20029:49AM
69
4. Sending
Faxes
4. Sending Faxes
Transmittable Documents
Size and weight
The size and weight of documents that you can load in the document feeder
depend on whether you load one page at a time or several pages at once.
Note: Letters or graphics on the edges of a document will not be scanned.
0.16"(4 mm)
0.16"(4 mm)
0.2"(5 mm)
0.2"(5 mm)
Letters in the
shaded area will
not be scanned.
8.5"
(216 mm)
23.6"
(600 mm)
14 lbs.
(52 g/m² )
42 lbs.
(157 g/m²)
11"
(279 mm)
8.5"
(216 mm)
21.5 lbs.
(80 g/m²)
Loading one page at a time:
Minimum size
Maximum size
Minimum weight Maximum weight
Minimum size Maximum size
Minimum weight Maximum weight
14 lbs.
(52 g/m² )
Loading up to 10 pages at once:
5.5"
(140 mm)
5.8"
(148 mm)
5.5"
(140 mm)
5.8"
(148 mm)
The illustration shows the
scanning margins for letter-
size documents. The scanning
width is 8.3” (210 mm). The
horizontal margins decrease
for smaller-width documents.
all.bookPage69Friday,May31,20029:49AM
Loading the Document
70
Other restrictions
♦ The scanner cannot recognize yellow, greenish yellow, or light blue ink.
♦ Ink, glue, and correcting fluid on documents must be dry before they pass
through the document feeder.
♦ All clips, staples, and pins must be removed from documents before loading
in the feeder. If these are not removed, they may damage the machine.
♦ Documents which are patched, taped, torn, smaller than the minimum size,
carbon backed, easily smudged, or have a slick coated surface should be
photocopied, and the copy loaded in the feeder.
Loading the Document
Up to 10 pages can be placed in the feeder at one time. The pages will
automatically feed into the machine starting from the bottom page.
♦ If you need to send or copy more than 10 pages, place the additional pages
gently and carefully in the feeder just before the last page is scanned. Do
not try to force them in, as this may cause double-feeding or jamming.
♦ If your document consists of several large or thick pages which must be
loaded one at a time, insert each page into the feeder as the previous page
is being scanned. Insert gently to prevent double-feeding.
1 Adjust the document guides to the
width of your document.
2 Insert the document face down in the
document feeder. The top edge of the
document should enter the feeder first.
• READY TO SEND will appear in the
display.
all.bookPage70Friday,May31,20029:49AM
Adjusting the Resolution and Contrast
71
4. Sending
Faxes
Adjusting the Resolution and Contrast
If desired, you can adjust the resolution and contrast before sending a
document.
Note: The resolution and contrast settings are only effective for sending a
document. They are not effective for receiving a document.
Resolution settings
STANDARD Use STANDARD for ordinary documents. This
setting gives you the fastest and most
economical transmission.
FINE Use FINE for documents containing small letters
or fine drawings.
SUPER FINE Use SUPER FINE for documents containing
very small letters or very fine drawings.
HALF TONE Use HALF TONE for photographs and
illustrations. The original will be reproduced in
64 shades of gray.
You must adjust the
settings each time
you don’t want to use
the default settings.
The default resolution
setting is STANDARD
and the default contrast
setting is AUTO.
3 Adjust the resolution and/or contrast settings as explained in
Resolution and Contrast below, then dial the receiving machine as
explained on page 72.
all.bookPage71Friday,May31,20029:49AM
Adjusting the Resolution and Contrast
72
Note: In order to transmit in SUPER FINE resolution, the receiving fax machine
must also have that resolution. If it doesn’t, your machine will automatically step
down to the next best available setting.
1 Load the document(s).
• The document must be loaded before
the resolution and contrast can be
adjusted.
2 Press one or more times until
the desired resolution and contrast
settings appear in the display.
• The first time you move through the list
of resolution settings, the contrast
setting AUTO will appear next to each
resolution setting. The second time you
move through the list, the contrast
setting DARK will appear.
RESOLUTION/
RECEPTION MODE
Display:
STANDARD :AUTO
FINE :AUTO
SUPER FINE :AUTO
HALF TONE :AUTO
STANDARD :DARK
HALF TONE :DARK
Contrast settings
AUTO Use AUTO for normal documents.
DARK Use DARK for faint documents.
all.bookPage72Friday,May31,20029:49AM
Sending a Fax by Normal Dialing
73
4. Sending
Faxes
1 Load the document(s).
• If desired, press to set the
resolution and/or contrast.
2 Pick up the handset or press .
Listen for the dial tone.
3 Dial the number of the receiving
machine by pressing the number keys.
4 Wait for the connection. Depending on the setting of the receiving
machine, you will either hear a fax tone or the other person will answer.
• If the other party answers, ask them to press their Start key (if you pressed
, pick up the handset to speak with them). This causes the receiving
machine to issue a fax tone.
RESOLUTION/
RECEPTION MODE
SPEAKER
SPEAKER
or
Sending a Fax by Normal Dialing
With Normal Dialing, you pick up the handset (or press ) and dial by
pressing the number keys.
♦ If a person answers, you can talk with them through the handset before
sending the fax. (If you pressed , you must pick up the handset to
talk.)
♦ Normal Dialing allows you to listen to the line and make sure the other fax
machine is responding.
SPEAKER
SPEAKER
JKL
ABC
1
DEF
WXYZ
9
GHI
4
5
MNO
6
PQRS
7
TUV
8
0
2 3
DELETE
REPEAT
SKIP
READY TO SEND
SPEAKER
all.bookPage73Friday,May31,20029:49AM
Sending a Fax by Automatic Dialing
74
Sending a Fax by Automatic Dialing
You can store your most frequently dialed fax or phone numbers in the
machine for automatic dialing.
♦ Auto-dial numbers can be stored using either the fax machine or the
cordless handset (to store a number using the cordless handset, see page
36).
♦ Numbers stored using the fax machine are stored in the Common book. A
total of 40 numbers can be stored.
Storing fax and phone numbers for automatic dialing
1 Press once and once.
2 Press once.
3 Enter the fax or voice number by pressing the number keys.
(Note: A space cannot be entered.)
• To clear a mistake, press .
• If a pause is required between any of the digits to access a special service
or an outside line, press . The pause appears as a hyphen (two
seconds per pause). Several pauses can be entered in a row.
FUNCTION
SPEAKER
FUNCTION
5 When you hear the fax tone, press . Replace the handset.
• If the transmission is completed successfully, the fax will beep once.
• If an error occurs, the fax will beep three times and print a Transaction
Report to inform you of the problem (see page 101).
START/MEMORY
Display:
ENTER FAX #
<NEW NUMBER>
Note: If the transmission is unsuccessful and DOCUMENT JAMMED appears
in the display, remove the document as explained on page 119. (This may
occur if the other fax machine doesn’t respond properly when you attempt to
send the document.)
all.bookPage74Friday,May31,20029:49AM
Sending a Fax by Automatic Dialing
75
4. Sending
Faxes
4 Press .
5 Enter a name by pressing number keys for each letter as shown in the
chart below. Up to 15 characters can be entered. (If you do not wish to
enter a name, go directly to Step 6.)
Example: SHARP = 7777 44 2 777 7
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears.
♦ To enter one of the following symbols, press or repeatedly:
. / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | }
) (
6 Press .
7 Return to Step 2 to store another number, or press to return to
the date and time display.
START/MEMORY
START/MEMORY
STOP
A =
B =
C =
D =
E =
F =
G =
H =
I =
J =
K =
L =
M =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
X =
Y =
Z =
SPACE =
Display:
Note: The fax machine uses a lithium battery to keep automatic dialing numbers
and other programmed information in memory when the power is turned off.
Battery power is consumed primarily when the power is off. With the power kept
continuously off, the life of the battery is about 5 years. If the battery dies, have
your dealer or retailer replace it. Do not try to replace it yourself.
<NEW NUMBER>
all.bookPage75Friday,May31,20029:49AM
Sending a Fax by Automatic Dialing
76
Editing and clearing auto-dial numbers
If you need to make changes to a previously stored auto-dial number, or clear
a number, follow these steps:
1 Press once and once.
2 Press or until the number you wish to edit or clear appears in
the display.
3 Press .
4 Press for EDIT or for CLEAR.
• If you selected CLEAR, go to Step 8.
5 If you selected EDIT, make the desired changes to the number.
• Press or to move the cursor to the digit or digits you wish to
change, and then enter the new digit. The new digit will replace the old
digit.
• If you do not wish to change the number, go directly to Step 6.
6 Press .
7 Make the desired changes to the name.
• Press or to move the cursor to the letter or letters you wish to
change, and then press the appropriate number key repeatedly until the
desired letter appears (see Step 5 on page 75). The new letter will replace
the old letter.
• If you do not wish to change the name, go directly to Step 8.
FUNCTION
1
2
START/MEMORY
Display:
1=EDIT, 2=CLEAR
<NEW NUMBER>
all.bookPage76Friday,May31,20029:49AM
Sending a Fax by Automatic Dialing
77
4. Sending
Faxes
8 Press .
9 Return to Step 2 to edit or clear another number, or press to
return to the date and time display.
START/MEMORY
STOP
Using an auto-dial number
Once you have stored a fax or phone number, you can use it to send a fax or
make a phone call.
1 If you are sending a fax, load the
document(s).
• If desired, press to set the
resolution and/or contrast.
2 Press (or ) until the name of the other party appears in the
display (if no name was stored, the number will appear).
3 If you are sending a fax, press . Dialing and transmission
begins.
• If the transmission is completed successfully, the fax will beep once.
• If an error occurs, the fax will beep three times and print a Transaction
Report to inform you of the problem (see page 101).
If you are making a phone call, lift the handset. Dialing begins.
RESOLUTION/
RECEPTION MODE
START/MEMORY
READY TO SEND
all.bookPage77Friday,May31,20029:49AM
Sending a Fax by Automatic Dialing
78
Sending a fax by Direct Keypad Dialing
You can also enter a full number with the number keys and then press the
key to begin dialing. You can use this method to dial a full number
when you don't need to speak to the other party before faxing.
START/MEMORY
1 Load the document(s).
• If desired, press to set the
resolution and/or contrast.
2 Enter the number of the receiving machine by pressing the number
keys.
• If a pause is required between any of the digits to access a special service
or an outside line, press . The pause will appear as a hyphen (two
seconds per pause). Several pauses can be entered in a row.
3 Check the display. If the number of the receiving machine shown is
correct, press .
• If the number is not correct, press to backspace and clear one digit
at a time, and then re-enter the correct digit(s).
RESOLUTION/
RECEPTION MODE
FUNCTION
START/MEMORY
STOP
READY TO SEND
all.bookPage78Friday,May31,20029:49AM
Sending a Fax by Automatic Dialing
79
4. Sending
Faxes
1 If you are sending a fax, load the
document(s).
• If desired, press to set the
resolution and/or contrast.
2 Press once. <REDIAL> appears in the display, followed by the last
number dialed. Make sure the number that appears is the number you
wish to dial.
3 If you are sending a fax, press . Dialing begins.
If you are making a phone call, lift the handset. Dialing begins.
RESOLUTION/
RECEPTION MODE
START/MEMORY
Redial
You can automatically redial the last number dialed on the fax machine. This
procedure can be used to send a fax or make a phone call.
Note: The fax machine and the cordless handset each retain their own
separate redial numbers.
Automatic redialing
If you use automatic dialing (including Direct Keypad Dialing) to send a fax
and the line is busy, the fax machine will automatically redial the number. The
fax machine will make three redial attempts at intervals of five minutes. During
this time, RECALLING will appear in the display, followed by a two-digit
number assigned to the fax job. You will not be able to dial any other locations
while the message appears.
Note: If a fax transmission is unsuccessful and DOCUMENT JAMMED
appears in the display, remove the document as explained on page 119. (This
may occur if the other fax machine doesn’t respond properly when you
attempt to send the document.)
all.bookPage79Friday,May31,20029:49AM
Sending a Fax by Automatic Dialing
80
Error Correction Mode
The fax machine is set to automatically correct any distortions in a
transmission due to noise on the telephone line before printing at the
receiving end. This function is called Error Correction Mode (ECM). ECM is
effective for both transmissions and receptions, and is only effective when the
other fax machine has ECM as well.
If desired, you can turn ECM off. This will increase slightly the amount of
memory available for memory transmission and reception.
1 Press once and once.
2 Press once and 6 times.
3 Press once.
4 Press to select YES, or to
select NO.
5 Press to return to the date and
time display.
FUNCTION
1
2
STOP
OPTION SETTING
ECM MODE
1=YES, 2=NO
The display briefly shows
your selection, then:
DAY LIGHT SAVE
♦ You can press to clear the message and stop automatic redialing.
♦ Under certain conditions (for example if a person answers the call on a
telephone), automatic redialing may stop before three redialing attempts
are made.
STOP
all.bookPage80Friday,May31,20029:49AM
Sending a Fax From Memory
81
4. Sending
Faxes
Sending a Fax From Memory
You can scan a document into the fax’s memory and send the document from
memory. This increases transmission speed and allows you to send a fax to
multiple destinations in a single operation. After transmission, the document is
automatically cleared from memory.
Note: If a power failure occurs while sending a fax from memory, you will need
to repeat the operation.
Broadcasting (sending a fax to multiple destinations)
This function allows you to send the same fax to as many as 20 different
destinations in just one operation.
♦ When sending to multiple destinations, only auto-dial numbers can be used
to dial the numbers of the receiving machines.
1 Load the document(s).
• If desired, press to set the
resolution and/or contrast.
2 Press .
3 Press (or ) until the name of the destination appears in the
display (if no name was stored, the number will appear).
4 Press to select the destination.
5 Repeat Steps 3 and 4 for each of the other destinations to which you
wish to send the fax (maximum of 20).
• To check your selected destinations, press to scroll through them. To
delete a destination, scroll to the destination and then press .
RESOLUTION/
RECEPTION MODE
START/MEMORY
STOP
all.bookPage81Friday,May31,20029:49AM
Sending a Fax From Memory
82
Memory transmission
You can also send a fax through memory when sending to a single
destination. This is convenient when sending to destinations where the line is
often busy, as it saves you from waiting to pick up the original document and
frees the feeder for other operations.
6 When you are ready to begin transmission, press .
• A Transaction Report is automatically printed out after Broadcasting is
completed. Check the "Note" column of the report to see if any of the
destinations are marked "Busy" or have a communication error code. If so,
send the document to those destinations again.
START/MEMORY
To send a fax through memory, load the document, press , and then
dial using one of the following methods:
♦ Press the number keys to enter the fax number and then press .
♦ Press repeatedly to select an auto-dial number and press .
♦ Press once to select the last number dialed and press .
START/MEMORY
START/MEMORY
START/MEMORY
START/MEMORY
If the memory becomes full...
If the memory becomes full while the document is being scanned, MEMORY
IS FULL and SEE MANUAL will alternately appear in the display.
♦ Press if you want to transmit the pages which have been stored up
to that point in memory. The remaining pages will be ejected from the
feeder. After transmission, the memory will be cleared and you can transmit
the remaining pages. You will also need to transmit the page which was
being scanned when the memory filled up.
♦ Press if you want to cancel the entire transmission.
START/MEMORY
STOP
all.bookPage82Friday,May31,20029:49AM
83
5. Receiving
Faxes
When the reception mode is set to FAX, the fax machine will automatically
answer all calls on four rings and receive incoming faxes.
♦ If you pick up the handset before the machine answers, you can talk to the
other party and/or receive a fax as explained in Using TEL Mode on page
84.
4 rings Fax reception
5. Receiving Faxes
Using FAX Mode
RESOLUTION/
RECEPTION MODE
Changing the number of rings
If desired, you can change the number of rings on which the fax machine
answers incoming calls in FAX mode. Any number from 2 to 5 can be
selected.
1 Press once and once.
FUNCTION
Display:
FAX
TEL
TAD
OPTION SETTING
To select FAX mode, press
until the arrow in
the display points to FAX.
RESOLUTION/
RECEPTION MODE
all.bookPage83Friday,May31,20029:49AM
Using TEL Mode
84
2 Press once.
3 Press once.
4 Enter the desired number of rings (any
number from 2 to 5).
Example: 3 rings
5 Press to return to the date and time display.
Note: If you are using Distinctive Ring, the fax machine will answer calls after two
rings regardless of the above setting.
3
STOP
Using TEL Mode
The display briefly shows
your selection, then:
To select TEL mode, press
until the arrow in
the display points to TEL.
RESOLUTION/
RECEPTION MODE
When the reception mode is set to TEL, you must answer all calls by picking
up the fax machine’s handset or an extension phone connected to the same
line.
RESOLUTION/
RECEPTION MODE
FAX
TAD
TEL
NUMBER OF RING
TRANSACTION
ENTER (2-5) (4)
all.bookPage84Friday,May31,20029:49AM
Using TEL Mode
85
5. Receiving
Faxes
1 When the fax machine rings, pick up
the handset.
2 If you hear a fax tone, wait until the
display shows RECEIVING and then
replace the handset.
3 If the other party first speaks with you
and then wants to send a fax, press
after speaking. (Press before
the sender presses their Start key.)
• When RECEIVING appears in the
display, hang up.
START/MEMORY
Answering on an extension phone connected to the same
line
Answering with the fax’s handset
Note: If you have set the Fax Signal Receive
setting to NO, press to begin reception.
START/MEMORY
Beep
START/MEMORY
1 Answer the extension phone when it
rings.
RECEIVING
RECEIVING
all.bookPage85Friday,May31,20029:49AM
Optional Reception Settings
86
2 If you hear a soft fax tone, wait until your fax responds (you will hear
pronounced, high-pitched tones), then hang up.
3 If the fax doesn't respond, or if the other party first talks to you and then
wants to send a fax, set the phone down (do not hang up), walk over to
the fax, lift the fax’s handset, and press .
• The above step is necessary if you have set the Fax Signal Receive setting
to NO.
START/MEMORY
Pronounced, high-pitched
tones
Beep
Optional Reception Settings
Fax Signal Receive
Your fax will automatically begin reception if you hear a soft fax tone after
answering a call on your fax or an extension phone. If you use a computer fax
modem to send documents on the same line, you must turn this function off in
order to prevent your fax from mistakenly attempting to receive documents
from the computer fax modem. Follow the steps below to change the setting.
1 Press once and once.
2 Press once and 4 times.
3 Press once.
FUNCTION
Display:
OPTION SETTING
FAX SIGNAL RX
1=YES, 2=NO
all.bookPage86Friday,May31,20029:49AM
Optional Reception Settings
87
5. Receiving
Faxes
4 Press to turn on the function, or
to turn it off.
5 Press to return to the date and time display.
1
2
STOP
Reception Ratio
The fax has been set at the factory to automatically reduce the size of
received documents to fit the size of the printing paper. This ensures that data
on the edges of the document are not cut off. If desired, you can turn this
function off and have received documents printed at full size.
♦ If a document is too long to fit on the printing paper, the remainder will be
printed on a second page. In this case, the cut-off point may occur in the
middle of a line.
♦ Automatic reduction may not be possible if the received document is too
large, contains too many fine graphics or images, or is sent at high
resolution. In this case, the remainder of the document will be printed on a
second page.
1 Press once and once.
2 Press once and 4 times.
3 Press once.
4 Press to select AUTO, or to
select 100%.
FUNCTION
1
2
The display briefly shows
your selection, then:
Display:
CALLER-ID
OPTION SETTING
RECEIVE RATIO
The display briefly shows
your selection, then:
PRINT CONTRAST
1=AUTO, 2=100%
all.bookPage87Friday,May31,20029:49AM
Substitute Reception to Memory
88
Substitute Reception to Memory
In situations where printing is not possible, such as when your fax runs out of
paper, the imaging film needs replacement, or the paper jams, incoming faxes
will be received to memory.
When you have received a document in memory, FAX RX IN MEMORY will
appear in the display, alternating with ADD PAPER & PRESS START KEY or
CHECK FILM / CHECK COVER / CHECK PAPER JAM. When you add paper
(and press ), replace the imaging film, or clear the jam, the stored
documents will automatically print out.
♦ If you received documents in memory because the fax ran out of paper, be
sure to add paper which is the same size as the paper previously used. If
not, the document print-out size may not match the size of the printing
paper.
START/MEMORY
5 Press to return to the date and time display.
STOP
all.bookPage88Friday,May31,20029:49AM
89
6. Making
Copies
6. Making Copies
Your fax machine can also be used to make copies. Single and multiple copies
(up to 99 per original) can be made, enabling your fax to double as a
convenience office copier.
1 Load the document(s) face down.
(Maximum of 10 pages.)
• If desired, press to set the
resolution and/or contrast.
(The default resolution setting for
copying is FINE.)
2 If desired, select an enlarge/reduce setting, and/or select the number of
copies per original:
• ENLARGE/REDUCE: Press or until the desired setting appears
in the display. Settings are 100%, 125%, 135%, 50%, 73%, 88%, 94%, and
AUTO (auto size adjustment to match the size of the paper). The default
setting is 100%.
Example: Press twice
• Number of copies per original: Press the number keys to enter a number
from 1 to 99. The default setting is 1.
Example: Press for five copies
3 When you are ready to begin copying, press .
RESOLUTION/
RECEPTION MODE
5
COPY/HELP
READY TO SEND
RATIO: 125%
5
If MEMORY IS FULL appears...
If the memory becomes full while a document is being scanned, MEMORY IS
FULL and SEE MANUAL will alternately appear in the display and the
document will automatically feed out. This may happen if the resolution is set
to SUPER FINE, or if you selected an enlarge/reduce setting, or if you are
making more than one copy per original. To avoid using memory, use
STANDARD or FINE for the resolution, 100% for the enlarge/reduce setting,
and make only one copy per original.
all.bookPage89Friday,May31,20029:49AM
Making Copies
90
1 Press once and once.
2 Press once and once.
3 Press once.
4 Press to set copy cut-off to YES
(the remaining part of the document
will not be printed), or to set copy
cut-off to NO (the remaining part will
be printed on a second page).
5 Press to return to the date and time display.
FUNCTION
1
2
STOP
Display:
The display briefly shows
your selection, then:
OPTION SETTING
COPY CUT-OFF
NUMBER OF RING
1=YES, 2=NO
Copy Cut-off
When making a copy of a document that is longer than the printing paper, use
the copy cut-off setting to select whether the remaining part of the document
will be cut off or printed on a second page. The initial setting is YES (cut off
the remainder). To change the setting, follow the steps below.
all.bookPage90Friday,May31,20029:49AM
91
7. Special
Functions
7. Special Functions
Caller ID (Requires Subscription to Service)
If you subscribe to a caller identification service from your telephone
company, you can have the fax machine and the cordless handset display the
name and number of the caller when you receive a call.
Important:
♦ To use this function, you must subscribe to a caller identification service
from your telephone company. Note that your fax may not be compatible
with some caller identification services.
♦ Area Code mode: This step is needed if your telephone exchange cannot
dial a local phone number (within your calling area code) when the area
code is dialed with the phone number (see Step 5).
1 Press once and once on
the fax machine.
2 Press once and 5 times.
3 Press once.
4 Press (YES) to turn on Caller ID.
(To turn off Caller ID, press and go
to Step 8.)
5 Press to select SET.
(To clear a previously set area code,
press and go to Step 8.)
Note: Entering your area code in this step causes it to be automatically removed
from local numbers in the Caller ID list (page 93). This is only required if you need
to eliminate dialing of the area code when dialing a local number from the list.
Example (using the area code “123”): If Step 5 is skipped, the Caller ID display will
show 123-444-1234, and the number that will dial from the Caller ID list is 123-
444-1234. If the area code 123 is entered in Step 5, the Caller ID display will show
444-1234, and the number that will dial from the Caller ID list is 444-1234.
FUNCTION
1
2
1
2
Display:
OPTION SETTING
CALLER-ID
AREA CODE # MODE
ENTER AREA CODE
1=YES, 2=NO
1=SET, 2=CLEAR
all.bookPage91Friday,May31,20029:49AM
Caller ID (Requires Subscription to Service)
92
6 Enter the three digits of your area code.
7 Press to store your area code.
8 Press to return to the date and time display.
START/MEMORY
STOP
How Caller ID operates
When you receive a call, the name and phone number of the caller will appear
in the fax machine display and cordless handset display, beginning just before
the second ring. The information will continue to be displayed until the line is
disconnected.
Note: Some caller ID services may not provide the name of the caller. In this case,
only the phone number will appear.
Display messages
One of the following messages will appear while the fax rings if caller
information is not available.
NO SERVICE No caller information was received from your telephone
company. Make sure that the telephone company has
activated your service.
CALLER-ID ERROR Noise on the telephone line prevented reception of
caller information.
OUT OF AREA The call was made from an area which does not have a
caller identification service, or the caller’s service is not
compatible with that of your local phone company.
PRIVATE CALL Caller information was not provided by the telephone
company at the caller’s request.
Display example (fax machine display)
Caller’s name Caller’s number
JOHN DOE 525-8693
ECM MODE
all.bookPage92Friday,May31,20029:49AM
Caller ID (Requires Subscription to Service)
93
7. Special
Functions
Viewing the Caller ID list
If you subscribe to a Caller ID service and have turned on the Caller ID
function, your fax machine will keep information on the most recent 30 calls
and faxes you have received. You can view this information, which consists of
the name and number of each caller, in the Caller ID List.
♦ After you have received 30 calls, each new call will delete the oldest call.
♦ All calls will be erased if you unplug the fax or a power failure occurs.
Follow the steps below to view the Caller ID List in the fax machine display. If
desired, you can immediately dial a number when it appears.
1 Press twice.
2 Press or to scroll through the list.
3 If you wish to dial one of the numbers in the list, scroll through the list
until the number appears in the display.
• Fax: If you wish to send a fax, load the
document and then press .
Dialing and transmission begin.
• Voice call: If you wish to make a voice
call, pick up the handset (or press
). Dialing begins automatically. (If
you pressed , pick up the
handset when the other party answers.)
4 Press when you have finished viewing the list.
START/MEMORY
SPEAKER
SPEAKER
STOP
START/MEMORY
Fax:
Voice
call:
<REVIEW CALLS>
all.bookPage93Friday,May31,20029:49AM
Caller ID (Requires Subscription to Service)
94
To delete calls from the Caller ID list
If you want to delete a single call from the caller list, press while the call
appears in the display. If you want to delete all calls from the list, hold
down for at least 3 seconds while you are viewing any number in the list.
0
0
Viewing the Caller ID list from the cordless handset
You can also view the Caller ID list in the cordless handset display, and
automatically dial a number from the list. (Note that the cordless handset and
the fax machine share the same list.)
1 Press .
2 Press or to scroll through the numbers in the list.
3 While viewing the list, you can do the following:
• Dial a number: Scroll to the desired number and then press . (Note:
You can only make a phone call from the cordless handset; you cannot
start a fax transmission.)
• Erase a call: Scroll to the call you wish to erase, press , and then
press .
4 Press when you have finished viewing the list.
REVIEW
TALK
ERASE
HOLD
START
OFF
OFF
REVIEW CALLS
▲▼: REVIEW
Cordless handset display:
all.bookPage94Friday,May31,20029:49AM
Caller ID (Requires Subscription to Service)
95
7. Special
Functions
1 Press once and 3 times.
2 Press once and twice.
3 Press once.
FUNCTION
Priority Call
If you have turned on Caller ID, you can set the machine to make a special
ringing sound when you receive a call from a designated phone number. This
lets you know immediately who is calling without having to look at the display.
To use this function, enter the desired phone number by following the steps
below (only one phone number can be entered).
Display:
ENTRY MODE
PRIORITY #
1=SET, 2=CLEAR
Erasing all calls using the cordless handset
Follow these steps to erase all calls from the Caller ID list using the cordless
handset.
1 Press .
2 Press .
3 Press .
• To cancel, press .
REVIEW
ERASE
HOLD
START
OFF
OFF
REVIEW CALLS
▲▼: REVIEW
Cordless handset display:
ERASE ALL?
PRESS START KEY
all.bookPage95Friday,May31,20029:49AM
Caller ID (Requires Subscription to Service)
96
Blocking voice calls
If you have turned on Caller ID, you can use the Anti Junk Fax function
described in Blocking Reception of Unwanted Faxes in this chapter to block
voice calls as well as faxes from your specified Anti Junk Number.
In this case, when a voice call or a fax transmission comes in from the number
you have specified as a "Junk Number", your fax will break the connection as
soon as it receives the calling phone number from the caller ID service (before
the second ring).
To use this function, enter the number that you wish to block as explained in
Blocking Reception of Unwanted Faxes (see page 98). Only one number can
be blocked.
Note: This function cannot be used if you are using the Distinctive Ring function.
4 Press to store a number.
(To clear a previously stored number, press and go to Step 6.)
5 Enter the number by pressing the number keys (max. 20 digits).
6 Press to store (or clear) the number.
7 Press to return to the date and time display.
1
2
START/MEMORY
STOP
HS NAME SET
all.bookPage96Friday,May31,20029:49AM
Distinctive Ring (Requires Subscription to Service)
97
7. Special
Functions
Distinctive Ring (Requires Subscription to
Service)
Important:
♦ To use distinctive ring, you must subscribe to a distinctive ring
service from your local phone company.
♦ Your fax machine may not be compatible with some distinctive ring
services.
Distinctive ring is a service offered by some local telephone companies
whereby they assign an additional second number to your regular single line.
The second number rings differently from your normal number.
If you subscribe to a distinctive ring service, you can set the fax machine to
automatically answer when your second number is called. This allows you to
use the second number as an exclusive fax number. To have your fax
automatically answer when your second number is called, follow the steps
below:
1 Press once and once.
2 Press once and 3 times.
3 Press once.
4 Press a number from 1 to 3 to select the ring pattern below that matches
your second number’s ring pattern. Or, press 4 to have your fax
automatically answer your normal telephone number. Press 5 to turn off
the distinctive ring function.
RING PATTERN 1 Two short rings
RING PATTERN 2 One short, one long, and one short ring
RING PATTERN 3 Two short rings and one long ring
STANDARD RING Your standard (normal) ring pattern
OFF SETTING Turn distinctive ring off
FUNCTION
Display:
1
2
3
4
5
OPTION SETTING
DISTINCTIVE
all.bookPage97Friday,May31,20029:49AM
Blocking Reception of Unwanted Faxes
98
5 Press to return to the date and time display.
6 Set the reception mode to FAX.
♦ When using distinctive ring, you must set the reception mode of your fax
machine to FAX. When your designated fax number is dialed, your fax will
automatically answer and begin reception after two rings. Note that other
devices on the same line will also ring until your fax answers. If one of your
other numbers is dialed, the fax will ring; however, it will not answer.
STOP
1 Press once and 3 times.
2 Press once and twice.
3 Press once.
4 Press to store an Anti Junk number, or to clear a previously
stored number (if you are clearing a number, go to Step 6).
5 Enter the fax number by pressing the number keys (max. 20 digits).
6 Press and then press to return to the date and time
display.
FUNCTION
1
2
START/MEMORY
STOP
Blocking Reception of Unwanted Faxes
The Anti Junk Fax function allows you to block reception of faxes from a party
that you specify. This saves paper by not printing out unwanted "junk" faxes.
To use this function, follow the steps below to enter the fax number from which
you do not wish to receive faxes. One fax number can be entered.
The display briefly shows
your selection, then:
RESOLUTION/
RECEPTION MODE
Display:
FAX
TEL
TAD
FAX SIGNAL RX
ENTRY MODE
ANTI JUNK #
1=SET, 2=CLEAR
all.bookPage98Friday,May31,20029:49AM
99
8. Printing
Lists
8. Printing Lists
You can print lists showing settings and information entered in the fax
machine. The lists are described below. To print a list, follow these steps.
1 Press once and twice.
2 Press once.
3 Press or until the desired list appears in the display.
4 Press once.
5 Press to print the list.
FUNCTION
START/MEMORY
Display:
LISTING MODE
TEL # LIST
PRESS START KEY
all.bookPage99Friday,May31,20029:49AM
Printing Lists
100
Message List
This list shows information about the messages currently recorded in the
answering machine, including the date and time each messages was
recorded, the length, and the type.
Caller-ID List
This list shows information about your 30 most recent calls. (This list is only
available if you are using the Caller ID function.)
Telephone Number List
This list shows the fax and phone numbers that have been stored in the
Common book for automatic dialing.
Setup List
This list shows your current selections for the FUNCTION key settings. The
list also shows your name and fax/telephone number as entered in the
machine, and a sample of the header printed at the top of every page you
transmit (HEADER PRINT).
all.bookPage100Friday,May31,20029:49AM
Printing Lists
101
8. Printing
Lists
Transaction Report
This report is printed out automatically after an operation is completed to
allow you to check the result. Your fax machine is set at the factory to print out
the report only when an error occurs.
♦ The Transaction report cannot be printed on demand.
Headings in Transaction Report
SENDER/
RECEIVER
The name or fax number of the other machine involved in the
transaction. If that machine does not have an ID function, the
communication mode will appear (for example, "G3").
START The time at which transmission/reception started.
TX/RX TIME Total time taken for transmission/reception.
PAGES Number of pages transmitted/received.
NOTE (One of the following notes will appear under NOTE in the
report to indicate whether the transaction was successful,
and if not, the reason for the failure.)
OK - Transmission/reception was successful.
P.FAI L - A power failure prevented the transaction.
JAM - The printing paper or document jammed, preventing
the transaction.
BUSY - The fax was not sent because the line was busy.
COM.E-X - (Where “X” is a number.) A telephone line error
prevented the transaction. See Line error on page 108.
CANCEL - The transaction was cancelled because the
STOP key was pressed, no document was in the feeder, or
the other machine requested transmission using a function
which your fax machine does not have. If you were
attempting to fax, make sure a document is in the feeder. If
you were receiving, contact the faxing party to see how they
are trying to send to you.
all.bookPage101Friday,May31,20029:49AM
Printing Lists
102
Transaction Report print condition
You can change the condition under which a Transaction Report is printed out.
Follow the steps below.
1 Press once and once.
2 Press once and once.
3 Press once.
4 Press a number from to to select the condition for printing.
5 Press to return to the date and time display.
ALWAYS PRINT A report will be printed after each
transmission, reception, or error.
ERROR/MEMORY A report will be printed after an error or a
memory operation.
SEND ONLY A report will be printed after each
transmission.
ERROR ONLY A report will be printed only when an error
occurs.
NEVER PRINT A report will never be printed.
FUNCTION
1 5
STOP
Display:
The display briefly shows
your selection, then:
1
2
3
4
5
OPTION SETTING
TRANSACTION
DIAL MODE
1:ALWAYS PRINT
(Selections appear alternately)
all.bookPage102Friday,May31,20029:49AM
103
9. Maintenance
9. Maintenance
Print head
Clean the print head frequently to ensure optimum printing performance.
Note: Remove the paper from the paper tray before cleaning the print head.
1 Unplug the power cord, and open the
operation panel (press
➊).
2 Take the imaging film out of the print
compartment and place it on a sheet of
paper.
3 Wipe the print head with isopropyl
alcohol or denatured alcohol.
Caution!
• Do not use benzene or thinner. Avoid
touching the print head with hard
objects.
• The print head may be hot if your fax
machine has just received a large
number of documents. If this is the
case, allow the print head to cool prior
to cleaning.
1
2
Print head
all.bookPage103Friday,May31,20029:49AM
Maintenance
104
4 Place the imaging film back in the print
compartment.
5 Rotate the front gear until the film is taut, and then close the operation
panel (press down on both sides to make sure it clicks into place).
Scanning glass and rollers
Clean the scanning glass and rollers frequently to ensure the quality of
transmitted images and copies.
Note: Remove the paper from the paper tray before cleaning the scanning
glass and rollers.
1 Open the operation panel (press ➊).
1
2
all.bookPage104Friday,May31,20029:49AM
Maintenance
105
9. Maintenance
2 Flip up the green levers on each side of
the white roller.
3 Wipe the scanning glass (under the
white roller) and rollers with a cotton
swab.
• Make sure that all dirt and stains (such
as correcting fluid) are removed. Dirt
and stains will cause vertical lines on
transmitted images and copies.
If the scanning glass is difficult to clean
If you find it difficult to remove dirt from the scanning glass, you can try moistening
the swab with isopropyl alcohol or denatured alcohol. Take care that no alcohol
gets on the rollers.
4 Flip down the green levers on each side of the white roller. Rotate the
front gear until the film is taut, and then close the operation panel (press
down on both sides to make sure it clicks into place).
The housing
Wipe the external parts and surface of the machine with a dry cloth.
Caution!
Do not use benzene or thinner. These solvents may damage or discolor the
machine.
all.bookPage105Friday,May31,20029:49AM
Maintenance
106
Replacing the Cordless Handset Battery
Like any other battery, the rechargeable battery will eventually wear out. The
battery can normally be used for about two years, although this will vary
depending on the conditions of use.
If LOW BATTERY continues to appear in the cordless handset display after
the battery has been charged for 10 hours, replace it with the following
battery:
Replacement battery: Use only a Sharp UX-BA01 battery
(3.6 V Ni-MH battery, capacity: 850 mAh)
Caution:
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions.
1 Remove the battery cover by pressing
on the indentation as shown.
2 Unplug the battery connector and
remove the old battery.
3 Connect the battery connector ➊ of the new battery, and then place the
battery in the cordless handset, placing the wires as shown.
Black
Red
Black
Red
all.bookPage106Friday,May31,20029:49AM
Maintenance
107
9. Maintenance
4 Place the battery cover on the cordless
handset, making sure it snaps firmly
into place.
5 Place the cordless handset in the
charger with the dial pad facing
forward.
• Let the new battery charge for at least
10 hours.
Battery disposal
The battery pack contains a Nickel Metal Hydride battery. The battery must be
disposed of properly. Contact local agencies for information on recycling and
disposal plans in your area.
Wiping the charger contacts
To ensure that the battery charges properly, wipe the charger contacts once a
month with a cotton swab.
Charger contacts
all.bookPage107Friday,May31,20029:49AM
108
10. Troubleshooting
Problems and Solutions
If you have any problems with your fax, first refer to the following
troubleshooting guide. If you cannot solve the problem, call Sharp's Customer
Assistance Center at 1-877-794-8675.
Line error
Problem Solution
LINE ERROR appears in
the display.
Try the transaction again. If the error persists, check
the following:
• Check the connection. The cord from the TEL.
LINE jack to the wall jack should be no longer than
six feet.
• Make sure there are no modem devices sharing the
same telephone line.
• Check with the other party to make sure their fax
machine is functioning properly.
• Have your telephone line checked for line noise.
• Try connecting the fax machine to a different
telephone line.
• If the problem still occurs, your fax machine may
need service.
all.bookPage108Friday,May31,20029:49AM
Problems and Solutions
109
10. Trouble-
shooting
Dialing and transmission problems
Problem Solution
No dial tone when you
pick up the handset or
press the SPEAKER key.
• Make sure the handset cord is connected to the
correct jack. See Connecting the handset on page
14.
Dialing is not possible. • Make sure the power cord is properly plugged into
a power outlet.
• Make sure that the telephone line is properly
connected to both the TEL. LINE jack and the wall
jack (see page 15).
• Make sure that the fax machine is set to the correct
dialing mode for your telephone line. See Dial
mode on page 15.
The power is on, but no
transmission takes place.
• Make sure that the receiving machine has paper.
• If the receiving machine is in manual mode with no
attendant, reception will not be possible.
• Check the display for error messages.
• Pick up the handset and check for a dial tone.
Nothing is printed at the
receiving end.
• Make sure that the document for transmission is
placed face down in the feeder.
A distorted image is
received at the other end.
• Noise on the telephone line may cause distortion.
Try sending the document again.
• Make a copy of the document on your fax machine.
If the copy is also distorted, your fax machine may
need service.
all.bookPage109Friday,May31,20029:49AM
Problems and Solutions
110
Reception and copying problems
Problem Solution
The fax machine doesn't
receive documents
automatically.
• Make sure that the reception mode is set to FAX. If
you subscribe to a distinctive ring service, make
sure that the Distinctive Ring function is set to the
correct ring pattern. If you do not subscribe to a
distinctive ring service, make sure that Distinctive
Ring is set to OFF SETTING. (See Distinctive Ring
on page 97.)
The printing paper comes
out blank when you try to
receive a document.
• Make sure that the document is loaded properly in
the feeder of the transmitting machine. Make a
copy or print a report to confirm the printing ability
of your machine.
General print quality is
poor.
• It is important to select a paper that is appropriate
for the thermal transfer printer in your fax. We
recommend using laser quality paper that has a
very smooth finish. Copier paper will work, but it
sometimes tends to yield a lighter print quality.
The received document is
faint.
• Ask the other party to send higher contrast
documents. If the contrast is still too low, your fax
machine may need service. Make a copy or print a
report to check your machine’s printing ability.
Received images are
distorted.
• Noise on the telephone line may cause distortion.
Have the other party try sending the document
again.
• The print head may be dirty. See Print head on
page 103.
• Make a copy or print a report on your fax machine.
If the copy or report is also distorted, your fax
machine may need service.
A received document or
copy prints out in strips.
• Make sure the operation panel is completely closed
(press down on both sides of the panel).
all.bookPage110Friday,May31,20029:49AM
Problems and Solutions
111
10. Trouble-
shooting
The quality of copies is
poor and/or dark vertical
lines appear.
• Any dirt or material on the scanning glass will
cause spots to appear on copies and transmitted
faxes. Clean the scanning glass as explained on
page 104.
Reception/copying is
interrupted.
• If reception or copying takes place continuously for
a long time, the print head may overheat. Turn off
the power and let it cool down. If overheating
frequently occurs, try changing the print contrast
setting to LIGHT (see page 25).
Dark vertical lines appear
on copies and received
faxes.
• Try changing the print contrast setting to LIGHT
(see page 25).
General problems
Problem Solution
Auto-dial numbers cannot
be stored in the fax.
• Make sure the fax is plugged in and the imaging
film has been loaded. (Auto-dial numbers cannot
be stored if the imaging film has not been loaded.)
See Loading the Imaging Film in Chapter 1.
Nothing appears in the
display.
• Make sure the power cord is properly plugged into
a power outlet.
• Connect another electrical appliance to the outlet to
see if it has power.
The machine does not
respond when you press
any of its keys.
• If a beep sound is not made when you press the
keys, unplug the power cord and then plug it in
again several seconds later.
Automatic document
feeding does not work for
transmission or copying.
• Check the size and weight of the document (see
Transmittable Documents on page 69).
all.bookPage111Friday,May31,20029:49AM
Problems and Solutions
112
Cordless handset problems
Problem Solution
The cordless handset
does not operate and
nothing appears in the
display.
• Make sure the battery is properly connected inside
the cordless handset (see page 18).
• The battery may be low. Place the cordless
handset in the charger and let it charge.
Calls cannot be made or
received on the cordless
handset.
• Make sure the fax machine is plugged into a power
outlet and has power.
• Make sure the telephone line is properly connected
to both the TEL. LINE jack on the fax machine and
the wall jack (see page 15). (If the telephone line is
connected correctly, you should hear a dial tone
when you pick up the fax machine handset.)
• The battery may be low. Place the cordless
handset in the charger and let it charge.
• Calls cannot be made or received while the fax
machine is being used (while FAX BUSY appears
in the cordless handset display). Wait until the fax
machine is no longer being used.
• Calls cannot be made or received during a power
failure.
• You may be outside of the talking range. Move
closer to the fax machine.
all.bookPage112Friday,May31,20029:49AM
Problems and Solutions
113
10. Trouble-
shooting
The battery does not
charge.
• Make sure the cordless handset is placed in the
charger with the dial pad facing forward.
• Make sure the AC adapter is connected correctly to
the charger and the power outlet (see page 17).
• Wipe the charger contacts with a cotton swab.
• Make sure the battery is properly connected inside
the cordless handset (see page 18).
• The battery may need replacement (see page 106).
You hear noise or
interference during a call.
• Make sure the base antenna is fully upright on the
fax machine (see page 17).
• Other electrical appliances may cause interference.
Move away from any electrical appliances.
• Move closer to the fax machine. Note that large
metal objects, metal structures, and thick walls
between the fax machine and cordless handset will
reduce the talking range. If needed, try moving the
fax machine to a different location.
You hear beeps during a
call.
• You will hear beeps during a call and LOW
BATTERY will appear in the display if the battery is
low. Place the cordless handset in the charger and
let it recharge. If you hear beeps during a call and
need to continue the call, press the INTERCOM
key to transfer the call to the fax machine.
• You will hear beeps during a call and OUT OF
RANGE will appear in the display if you are outside
of the talking range. Move closer to the fax
machine.
When you press the
INTERCOM key, the name
of one of the other
cordless handsets does
not appear in the list (only
the number appears),
even though a name has
been programmed for that
cordless handset.
• The name was not transmitted to your cordless
handset when it was entered (probably because
your cordless handset was in use). To retransmit
the name, repeat the name entry procedure on
page 20. The name will automatically appear in the
display in Step 6, so simply press to
transmit the name then exit the procedure with Step
8.
START/MEMORY
all.bookPage113Friday,May31,20029:49AM
Messages and Signals
114
Messages and Signals
Display messages (fax machine)
Note: If you have turned on the Caller ID function, see page 92 for display
messages related to Caller ID.
ADD PAPER & /
PRESS START KEY
(alternating messages)
Check the printing paper. If the tray is empty, add
paper and then press the START/MEMORY key. If
there is paper in the tray, make sure it is inserted
correctly (take out the stack, align the edges evenly,
and then reinsert it in the tray) and then press the
START/MEMORY key.
BUSY The system is busy, or the cordless handset that you
attempted to page is busy and cannot respond.
CALL TRANSFER A call is being transferred.
CHECK FILM/
CHECK COVER/
CHECK PAPER JAM
(alternating messages)
These alternating messages appear when there is a
problem in the print compartment that prevents
printing. Check to see if the imaging film is not loaded
properly or if it has been used up and needs
replacement. Make sure the operation panel is
completely closed (press down on both sides). If a
paper jam has occurred, clear the jam as explained in
the following section, Clearing Paper Jams.
CHECK PAPER SIZE The paper size setting is incorrect. Change the paper
size setting as explained on page 25.
CORDLESS IN USE The cordless handset is in use. Wait until this
message no longer appears to send a fax or make a
phone call.
DOCUMENT JAMMED The original document is jammed. See the following
section, Clearing Paper Jams. Document jams will
occur if you load more than 10 pages at once or load
documents that are too thick (see page 69). The
document may also jam if the receiving machine
doesn’t respond properly when you attempt to send a
fax.
all.bookPage114Friday,May31,20029:49AM
Messages and Signals
115
10. Trouble-
shooting
FAX RX IN MEMORY A fax has been received in memory because the
imaging film needs replacement, you have run out of
printing paper, or the paper is jammed. The fax will
print out automatically when the problem is fixed.
FUNCTION MODE The FUNCTION key has been pressed.
INTERCOM A cordless handset is paging the fax machine (lift the
handset to talk), or the fax machine is paging a
cordless handset. The name and number of the
cordless handset appear alternately with
INTERCOM.
LINE ERROR Transmission or reception was not successful. Press
the STOP key to clear the message and then try
again. If the error persists, see Line Error on page
108.
MEMORY IS FULL/
SEE MANUAL
(alternating messages)
The memory is full. You may have too many
messages recorded in the answering system. To
erase messages, see page 53.
This message may also occur during fax reception if
too much data is received before the pages can be
printed out. If faxes have been received to memory
because printing is not possible (an additional
message will indicate the problem), resolve the
problem so that printing can continue (see Substitute
Reception to Memory on page 88).
If you are attempting to transmit from memory, see If
the memory becomes full on page 82.
If you are copying, see If MEMORY IS FULL appears
on page 89.
MEMORY PRINTING The fax is preparing to or printing out a document
from memory.
NO DATA This appears if you attempt to search for an auto-dial
number when none have been stored.
OFF HOOK This appears if you forgot to replace the handset after
using it to dial and send a fax. Replace the handset or
press the STOP key to clear the message.
ON HOOK DIAL The SPEAKER key has been pressed and the fax
machine is waiting for you to dial.
all.bookPage115Friday,May31,20029:49AM
Messages and Signals
116
OVER HEAT The print head has overheated. Operation can be
continued after it cools. If overheating frequently
occurs, try changing the print contrast setting to
LIGHT (see page 25).
PRINT HEAD FAIL/
YOU NEED SERVICE
(alternating messages)
The print head has failed and requires service.
READY TO SEND A document has been loaded and the fax machine is
waiting for you to begin faxing or copying.
RECALLING This appears if you attempt to send a fax by
automatic dialing and the line is busy or the receiving
fax machine does not answer. Your fax machine will
automatically reattempt the call. (See Automatic
redialing on page 79.)
REPLACE HANDSET This appears if an outside call comes in while you are
paging or talking to the cordless handset using the
Intercom feature. Replace the fax machine handset to
stop the Intercom call, and then pick it up again to
answer the outside call. This also appears after you
transfer a call to the cordless handset.
T.A.D. TRANSFER The answering system's transfer function has been
turned on (see page 59).
TOTAL MSGS:XX This indicates that you have received messages in
the answering system. “XX” is the number of
messages.
TOTAL PAGE(S) 01 Number of pages transmitted, received, or copied.
all.bookPage116Friday,May31,20029:49AM
Messages and Signals
117
10. Trouble-
shooting
Display messages (cordless handset)
BUSY The system is busy, or the fax machine or other
cordless handset that you attempted to page is busy
and cannot respond.
CALL TRANSFER A call is being transferred.
CHARGING The cordless handset is in the charger and the
battery is charging.
FAX BUSY The fax machine is in use. Wait until the fax machine
is no longer being used to use the cordless handset.
HOLD A call has been placed on hold by pressing the HOLD
key. To resume the call, press the HOLD key again.
IN CHARGER The cordless handset is in the charger and is fully
charged (the cordless handset can be left in the
charger without damaging the battery).
INTERCOM Your cordless handset is being paged (press the
TALK key to talk), or your cordless handset is paging
the fax machine or another cordless handset. The
number and name of the other handset appear
alternately with INTERCOM.
LOW BATTERY The cordless handset battery is low. Place the
cordless handset in the charger and let it recharge. If
this message continues to appear after recharging,
the battery may need replacement (see page 106). If
this message appears during a phone call (you will
also hear beeps) and you wish to continue the call,
press the INTERCOM key to transfer the call to the
fax machine.
NEW MESSAGES New messages have been received in your personal
box (the box corresponding to your cordless handset)
in the answering system. You can either listen to the
messages using the cordless handset (see page 54),
or using the fax machine (see page 52).
all.bookPage117Friday,May31,20029:49AM
Messages and Signals
118
OUT OF RANGE The cordless handset is outside of the talking range
of the fax machine. When talking on the cordless
handset, the handset will beep and you may hear
interference. Move closer to the fax machine.
PLEASE REGISTER This appears in the display of an accessory cordless
handset the first time it is charged. The handset must
be registered in order to use it (see the manual for the
accessory cordless handset).
REMOTE MODE The REMOTE/FLASH key has been pressed.
TALK The TALK key has been pressed to make a phone
call.
Audible signals
Continuous tone 3 seconds Indicates the end of transmission,
reception, or copying.
Intermittent tone
(3 beeps)
5 seconds
(1 second on, 1
second off)
Indicates incomplete transmission,
reception, or copying.
Rapid intermittent
tone
35 seconds
(0.7 seconds on,
0.3 seconds off)
Indicates that the handset is off hook.
all.bookPage118Friday,May31,20029:49AM
Clearing Paper Jams
119
10. Trouble-
shooting
Clearing Paper Jams
Clearing a jammed document
If the original document doesn’t feed properly during transmission or copying,
or DOCUMENT JAMMED appears in the display, first try pressing . If
the document doesn't feed out, remove it as explained below.
Important:
Do not try to remove a jammed document without releasing it as explained
below. This may damage the feeder mechanism.
START/MEMORY
1 Press ➊ and slowly open the operation
panel until it is half open.
2 Flip up the green levers on each side of
the white roller.
3 Gently remove the document.
• Be careful not to tear the document.
1
2
all.bookPage119Friday,May31,20029:49AM
Clearing Paper Jams
120
1 Open the operation panel (press ➊).
2 Gently pull the jammed paper out of
the machine, making sure no torn
pieces of paper remain in the print
compartment or rollers.
3 Rotate the front gear until the film is taut, and then close the operation
panel (press down on both sides to make sure it clicks into place).
Clearing jammed printing paper
4 Flip down the green levers on each side of the white roller. Rotate the
front gear until the film is taut, and then close the operation panel (press
down on both sides to make sure it clicks into place).
1
2
all.bookPage120Friday,May31,20029:49AM
Ordering Parts
121
Ordering Parts
To order parts, contact the parts distribution center located nearest
you. When ordering a part, use the part order number shown below.
Operation manual TINSE4273XHTZ
Setup Guide TCADZ3323XHZA
Handset cord QCNWG209BXHGY
Telephone line cord QCNWG208BXHZZ
Handset DUNTK468BXHGY
Paper tray CPLTP3183XHR7
Paper tray extension LPLTP3184XHZZ
Gears CGERH2566XH01
NGERH2568XHZZ
AC adapter RADPA2027XHZZ
Cordless handset charger RUNTZ2100XHE2
Part distribution centers
Tritronics, Inc.
1306 Continental Drive
Abingdon, MD 21009
Tel: 1-800-638-3328
Fax: 1-800-888-FAXD
Tritronics, Inc.
1015 NW 52nd Street
Ft. Lauderdale, FL 33309
Tel:1-800-365-8030
Fax: 1-800-999-FAXD
Fox International, Ltd.
23600 Aurora Road
Bedford Heights, OH 44146
Tel: 1-800-321-6993
Fax: 1-800-445-7991
Andrews Electronics
25158 Avenue Stanford
Santa Clarita, CA 91355
Tel: 1-800-274-4666
Fax: 1-805-295-5126
Sharp Accessories and
Supply Center
2130 Townline Road
Peoria, IL 61615
Tel: 1-800-642-2122
all.bookPage121Friday,May31,20029:49AM
FCC Regulatory Information
122
FCC Regulatory Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted
by the ACTA. On the rear of this equipment is a label that contains, among other
information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this
number must be provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details. This equipment connects to the
telephone network through a standard USOC RJ-11C network interface jack.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is part of
the product identifier that has the format US:AAAEQ##TXXXX. The digits represented
by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier
products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if
advance notice isn't practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens the
telephone company will provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, or for repair or warranty information,
please contact Sharp’s Customer Assistance Center. The number is 1-877-794-8675. If
the equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
This equipment may not be used on coin service provided by the telephone company.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this equipment ID does not disable your alarm equipment. If
you have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
This equipment is hearing-aid compatible.
When programming and/or making test calls to emergency numbers:
♦ Remain on the line and briefly explain to the dispatcher the reason for the call.
♦ Perform such activities in the off-peak hours, such as early morning or late evening.
all.bookPage122Friday,May31,20029:49AM
123
SHARP
Date Revised: .
Date Issued :July. 3. 2001
MATERIAL SAFETY DATA SHEET (1/2)
MSDS No. B-1026
Section 1. Product and Company Identification
Product Name : IMAGING FILM UX-5CR
Supplier Identification : Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Manufacturer : DAINIPPON PRINTING CO. LTD.
591-2, Kamihirose, Higashikubo, Sayamashi, Saitama, 350-1321 JAPAN
Emergency telephone number : +81-42-952-9666
Local suppliers are listed below. Please contact the nearest supplier for additional information.
Section 2. Ingredients
Ingredients CAS No. Proportion OSHA PEL ACGIH TLV Other
Polyethylene terephthalate film
25038-59-9 47 ~ 52% - - None
Coating layer substances
Carbon Black 1333-86-4 7 ~ 10% 3.5 mg/m
3
3.5 mg/m
3
None
Ester wax 8015-86-9 2 ~ 7% - - None
Parraffin Wax 8002-74-2 10 ~ 14% - 2.0 mg/m
3
None
Microcrystalline wax 63231-60-7 16 ~ 22% - - None
Ethylene Vinyl Acetate Copolymer
24937-78-8 1 ~ 5% - - None
Others 1 ~ 6% - - None
Section 3. Hazardous Identification
Route(s) of Entry: Inhalation? Skin? Ingestion?
NO NO Possible but very unusual
Signs and Symptoms of Exposure: None
Medical Conditions Aggravated by Exposure: None
POTENTIAL HEALTH EFFECTS:
Inhalation: None
Skin Contact: None
Eye Contact: None
Ingestion: None
Section 4. First-Aid Measures
Inhalation: No applicable
Skin Contact: In case of contact, usually special care in not necessary. If it dirties skin, clear with water and soap.
Eye Contact: In case of contact, immediately flush eyes with plenty of water. If necessary, then care for medical attention.
Ingestion: Immediately make vomit it and rinse mouth with water. If necessary, then care for medical attention.
Section 5. Fire-Fighting Measures
Flash Point: about 250
°
Cforink
Autoignition: None
Flammability Limits: Not applicable
Extinguishing Media: CO2, Water, Dry chemicals, Foam
Firefighting: None
Fire and Explosion Hazard: None
Hazardous Combustion Products: None
(Country) (Name and Telephone Number)
U.S.A. Sharp Electronics Corporation
Telephone number for information: 1-800-237-4277
Canada Sharp Electronics of Canada Ltd.
Telephone number for information : 905-890-2100
Emergency telephone number : 1-800-255-3924
all.bookPage123Friday,May31,20029:49AM
124
SHARP
Date Revised: .
Date Issued :July. 3. 2001
MATERIAL SAFETY DATA SHEET (2/2)
MSDS No. B-1026
Section 6. Accidental Release Measures
Rumpling the product may cause the wax layer to peel off. Sweep up or vacuum. When sweeping, avoid
raising film or dust. If a vacuum is used , motor should be rated as dust tight. Wash any residue off skin with
soap and water. Garments may be wasted or dry cleaned after removal of loose film or dust.
Section 7. Handling and Storage
No special precautions for safety reason.
Store in cool, dry place ,avoid direct sunlight.
Section 8. Exposure Control/Personal Protection
Ventilation: None
Eye Protection: None
Protective Clothing: None
Gloves: None
Section 9. Physical and Chemical Properties
Description: Not applicable
Melting Point: 71
°
C Freezing Point: None
Pressurized: None Boiling Point: None
pH: None Specific Gravity (H20 = 1): about 1.2
Evaporation Rate: Negligible Water Solubility: Not applicable
Volatility: None
Section 10. Stability and Reactivity
Stability: Stable
Conditions to Avoid: None
Incompatibility(Materials to Avoid): None
Hazardous Decomposition or Byproducts: CO, CO2, NOX and H2O
Hazardous Polymerization: Will not occur
Section 11. Toxicological Information
Acute Toxicity: None
Chronic Toxicity: None
Section 12. Ecological Information
No environmental effect at normal use.
Section 13. Disposal Consideration
Dispose by the same method of ordinary plastic products in accordance with all applicable regulations. Any
disposal practice must be in compliance with local, state and federal laws and regulations. If necessary,
contact government office and ensure conformity with disposal regulations.
Section 14. Transport Information
No specific precautionary transport measure for safety reasons.
As to storage conditions, see section 7.
Section 15. Regulatory Information
None
Section 16. Other Information
The information herein is given in good faith, but no warranty, if used any process.
Final determination of suitability of any material is the sole responsibility of the user.
Although certain information are described herein, we cannot guarantee, that these are the only hazard, which exist.
Information on this data sheet represents our current data and best opinion as to the proper use in handling of
this product under normal conditions.
Restrictions: This information relates only to the specific material designated as supplied by the manufacturer. This
information is supplied to us by the manufacturer and Sharp offers no warranties as to its accuracy and
accepts no responsibilities for any typographical errors which may appear on these sheets. It is the
responsibility of the user to determine the suitability of this product for each particular use.
all.bookPage124Friday,May31,20029:49AM
125
Quick Reference Guide
Sending Faxes
Place your document
(up to 10 pages) face
down in the document
feeder.
Normal Dialing
1.Lift the handset or press .
2. Dial the fax number.
3. Wait for the reception tone (if a person
answers, ask them to press their Start
key).
4. Press .
Automatic Dialing
1. Press or until the desired
destination appears in the display.
2. Press .
Direct Keypad Dialing
1. Dial the fax number.
2. Press .
Recording an OGM
1. Press , press until desired
OGM is displayed, and then
once.
2. Lift the handset, press , and
speak into the handset.
3. When finished, press .
SPEAKER
START/MEMORY
START/MEMORY
START/MEMORY
REC/
MEMO
START/MEMORY
STOP
Receiving Faxes
Press until the arrow in the
display points to the desired reception
mode.
FAX mode: The fax machine automatically
answers and receives faxes.
TEL mode: Answer all calls (even faxes)
by picking up the handset. To begin fax
reception, press .
TAD mode: Select this mode when you go
out to receive both voice messages and
faxes.
Storing Auto Dial Numbers
1. Press once and twice.
2. Enter the full fax/phone number.
3. Press .
4. Enter a name by pressing number keys.
(To enter two letters in succession that
require the same key, press after
entering the first letter.)
5. Press and then .
RESOLUTION/
RECEPTION MODE
START/MEMOR
Y
FUNCTION
START/MEMORY
START/MEMORY
STOP
FAX
TEL
JAN-02 10:30
FAX
TEL
JAN-02 10:30
FAX
TEL
JAN-02 10:30
TAD
TAD
TAD
RESOLUTION/
RECEPTION MODE
A =
B =
C =
D =
E =
F =
G =
H =
I =
J =
K =
L =
M =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
X =
Y =
Z =
SPACE =
all.bookPage125Friday,May31,20029:49AM
126
Using the Cordless Phone
Making a phone call
1. Pick up the cordless handset and press
.
2. When you hear the dial tone, dial the
number.
3.When you are ready to end the call,
press .
Making a phone call using automatic
dialing
1. Press once.
2.Press or to select the book.
3. Press or until the number you
wish to dial appears in the display.
4. Press .
Receiving a phone call
1.When the cordless handset rings, pick it
up and press any key to answer.
2. When you are ready to end the call,
press .
Receiving a fax using the cordless
handset
If you hear a fax tone after answering a
call on the cordless handset, or if the
other party speaks to you and then
wants to send a fax, press
.
TALK
OFF
OFF
SEARCH
TALK
OFF
OFF
START
Storing auto dial numbers
1. Press , or to select
the book, and then .
2. Enter the full fax/phone number.
To clear a mistake, press .
To insert a pause, press .
3. Press .
4. Enter a name by pressing number keys.
(To enter two letters in succession that
require the same key, press after
entering the first letter.)
5. Press and then .
Listening to messages
1. Press .
(For the general box, press .)
2. Press to listen to all your
messages, or to listen to only your
new messages.
3. While listening, you can press
, , ,
or .
4 When finished, press
SEARCH
FUNCTION
/PAUSE
ERASE
HOLD
FUNCTION
/PAUSE
START
START
OFF
OFF
REMOTE
/FLASH
0
PQRS
7
PLAY
TUV
8
PLAY NEW
REPEAT
0
SKIP
DELETE
STOP
WXYZ
9
OFF
OFF
A =
B =
C =
D =
E =
F =
G =
H =
I =
J =
K =
L =
M =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
X =
Y =
Z =
SPACE =
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
TUV
8
TUV
8
TUV
8
TUV
8
TUV
8
TUV
8
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
MNO
6
MNO
6
MNO
6
MNO
6
MNO
6
JKL
5
JKL
5
JKL
5
MNO
6
JKL
5
JKL
5
JKL
5
GHI
4
GHI
4
GHI
4
GHI
4
GHI
4
GHI
4
DEF
3
DEF
3
DEF
3
DEF
3
DEF
3
DEF
3
ABC
2
ABC
2
ABC
2
ABC
2
ABC
2
ABC
2
1
all.bookPage126Friday,May31,20029:49AM
127
Guía de referencia rápida
Transmisión de mensajes telefax
Coloque el original
(hasta 10 páginas) cara
abajo en el alimentador
de documentos.
Marcación normal
1.
Levante el auricular u oprima: .
2.
Marque el número de telefax.
3.
Espere hasta escuchar el tono de
recepción (si contestara una persona,
pídale oprimir su tecla Start).
4. Oprima: .
Marcación automática
1.Oprima la tecla de flecha o
hasta que en el visor aparazca el destino
deseado.
2.
Oprima: .
Marcación directa por teclado
1.
Marque el número de fax.
2.Oprima: .
Grabacion de un mensaje de
bienvenida
1. Oprima la tecla , oprima hasta
que en el visor aparezca el mensaje de
bienvenida deseado y, a continuación,
oprima una vez.
2. Levante el auricular,
oprima la tecla
y hable en el microtel
éfono.
3.
Oprima la tecla cuando haya
finalizado.
SPEAKER
START/MEMORY
START/MEMORY
START/MEMORY
REC/
MEMO
START/MEMORY
STOP
Recepción de mensajes telefax
Oprima hasta que la flecha que
hay en el display señale hacia el número de
recepción deseado
Modo FAX
: El aparato telefax contesta y
transmite automáticamente mensajes telefax.
Modo TEL: Responda a todas las llamadas
(incluso mensajes de fax), levantando el
auricular. Para iniciar la recepción de fax,
oprima
.
Modo TAD:
Seleccione este modo cuando
salga para recibir tanto mensajes hablados
como telefax.
Memorizar números marc.
automática
1. Oprima una vez y dos veces.
2. Introduzca el número de telefax/teléfono
completo.
3. Oprima: .
4.
Ingrese el nombre oprimiendo las teclas
numéricas. (Para ingresar sucesivamente
dos letras que requieren la misma tecla,
oprima
después de ingresar la
primera letra).
5. Oprima y luego .
RESOLUTION/
RECEPTION MODE
START/MEMORY
FUNCTION
START/MEMORY
START/MEMORY
STOP
FAX
TEL
JAN-02 10:30
FAX
TEL
JAN-02 10:30
FAX
TEL
JAN-02 10:30
TAD
TAD
TAD
RESOLUTION/
RECEPTION MODE
A =
B =
C =
D =
E =
F =
G =
H =
I =
J =
K =
L =
M =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
X =
Y =
Z =
SPACE =
all.bookPage127Friday,May31,20029:49AM
128
Uso del teléfono inalámbrico
Hacer una llamada
1. Descuelgue el teléfono inalámbrico y
oprima .
2.Marque los números cuando escuche el
tono de línea.
3. Oprima cuando esté listo para
finalizar la llamada.
Hacer una llamada usando la función de
marcación automática
1. Oprima una vez .
2. Oprima o para seleccionar el
list
ín.
3. Oprima o hasta que en el
display aparezca el número que desea
llamar.
4. Oprima .
Recibir una llamada
1. Cuando suene el timbre del teléfono
inalámbrico, descuélguelo y oprima una
tecla cualquiera para contestar.
2. Oprima cuando esté listo para
finalizar la llamada.
Recibir un mensaje telefax usando el
teléfono inalámbrico
Si después de atender una llamada con el
teléfono inalámbrico escucha el tono de
telefax o si el interlocutor desea remitirle
un mensaje telefax, oprima .
TALK
OFF
OFF
SEARCH
TALK
OFF
OFF
START
Memorizar números para marcación
automática
1. Oprima la tecla , o
para seleccionar el list
ín y, a continuación,
.
2. Introduzca el número de teléfono/telefax
completo.
Para borrar un error, oprima .
Para introducir una pausa, oprima .
3.Oprima .
4. Introduzca un nombre mediante
pulsación de las teclas numéricas.
(Para introducir dos letras consecutivas
que requieran el mismo código, oprima
después de introducir la primera
letra.
5. Oprima y, a continuación, .
Escuchar los mensajes
1. Oprima .
(Para el buzón general, oprima ).
2. Oprima para escuchar todos sus
mensajes o para escuchar sólo los
mensajes nuevos.
3. Mientras hace la escucha puede pulsar
, , ,
o .
4. Pulse cuando haya terminado.
SEARCH
FUNCTION
/PAUSE
ERASE
HOLD
FUNCTION
/PAUSE
START
START
OFF
OFF
REMOTE
/FLASH
0
PQRS
7
PLAY
TUV
8
PLAY NEW
REPEAT
0
SKIP
DELETE
STOP
WXYZ
9
OFF
OFF
A =
B =
C =
D =
E =
F =
G =
H =
I =
J =
K =
L =
M =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
X =
Y =
Z =
SPACE =
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
WXYZ
9
TUV
8
TUV
8
TUV
8
TUV
8
TUV
8
TUV
8
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
PQRS
7
MNO
6
MNO
6
MNO
6
MNO
6
MNO
6
JKL
5
JKL
5
JKL
5
MNO
6
JKL
5
JKL
5
JKL
5
GHI
4
GHI
4
GHI
4
GHI
4
GHI
4
GHI
4
DEF
3
DEF
3
DEF
3
DEF
3
DEF
3
DEF
3
ABC
2
ABC
2
ABC
2
ABC
2
ABC
2
ABC
2
1
all.bookPage128Friday,May31,20029:49AM
129
A
Answering system, activating, 50
Anti Junk Fax, 98
Audible signals, 118
Auto-dial numbers
Storing, 36, 74
Using, 38, 77
B
Battery
Disposing of, 107
Installing, 18
Replacing, 106
C
Caller ID, 91-96
Caller ID List, 100
Contrast, 72
Copies, 89
Copy cut-off setting, 90
Cordless handset
Auto-dial numbers, storing, 36
Auto-dial numbers, using, 38
Faxes, receiving, 36
Hold, 35
Listening to messages, 54
Making a call, 34
Name, 20
Receiver volume, 33
Receiving a call, 35
Reception mode, changing, 46
Redialing, 41
Ringer volume, 33
Talking range, 19
CPC Detection, 58
D
Date, setting, 28-29
Daylight Saving Time, 29
Dial mode, 15
Dialing
Automatic, 38, 77
Direct Keypad, 78
Normal, 34, 73
Direct Keypad Dialing, 78
Display messages, 92, 114-117
Distinctive ring, 97
Document feeder, 70
Document guides, 70
Document restrictions, 70
Document sizes, 69
Document, maximum scanning size, 69
E
ECM (Error Correction Mode), 80
Extension telephone, using, 85
F
FAX reception mode, 30, 83
Fax reception on TAD failure, 56
Fax Signal Receive, 86
H
Halftone setting, 71
Handset, 14
Handset receiver volume (fax machine),
31
Headset jack, 21
Housing, cleaning, 105
I
Imaging film, replacing, 22
Intercom, 41
J
Jams, clearing, 119-120
L
Letters, entering, 20, 27, 37, 75
Index
all.bookPage129Friday,May31,20029:49AM
Index
130
Line error, 108
Loading paper, 24
Loading the document, 70
M
Memory transmission, 82
Memory, substitute reception to, 88
Message List, 100
Messages
Erasing, 53, 54
Listening to, 52
Listening to on cordless handset, 54
Listening to remotely, 64
Setting allowed time, 56
N
Normal dialing, 34, 73
Number of rings in FAX reception mode,
83
Number of rings in TAD mode, 51
O
OGM only mode, 57
Ordering parts, 121
Outgoing message, 48
P
Paper jams, clearing, 119-120
Paper size setting, 25
Paper tray extension, 16
Paper, loading, 24
Personal box, setting passcode, 49
Power cord, 14
Print contrast setting, 25
Print head, cleaning, 103-104
Priority Call, 95
R
Reception mode
FAX mode, 30, 83
TAD mode, 30, 50
TEL mode, 30, 84
Reception Ratio setting, 87
Redialing, 41, 79
Remote code number, 62
Remote operations, 62
Resolution, 71
Ringer volume
Cordless handset, 33
Fax machine, 32
S
Scanning glass, cleaning, 104
Sender’s name and number, entering,
26-27
Setup List, 100
Speaker volume, 31
T
TAD reception mode, 30, 50
TEL reception mode, 30, 84
TEL. LINE jack, 15
Telephone line cord, 15
Telephone Number List, 100
Time, setting, 28-29
Toll Saver function, 51, 63
Transaction Report, 101
Setting print condition, 102
Transfer Function, 59
Transferring calls, 44
all.bookPage130Friday,May31,20029:49AM
1. Call your fax from a touch-tone telephone, and
press # when the outgoing message begins.
2. If you want to listen to a personal box, enter its
number.
3. Enter your passcode or remote code:
4. Press # .
5. After listening to your messages, you can either
hang up to save them, or enter one of the
commands on the reverse side.
REMOTE OPERATION CARD
The card below is provided as a quick guide to remote operation. Cut it out
and carry it with you when you go out.
Remote Operation Guide
all.bookPage131Friday,May31,20029:49AM
REMOTE COMMANDS
• FAX RECEPTION MODES
TAD mode......................... 81#
FAX mode......................... 82#
TEL mode......................... 83#
• TRANSFER FUNCTION
Turn on ............................. 91#
(Box#)
#
Turn off ............................. 92#
New transfer number........ 90#
(Tel. #)
#
Record transfer OGM....... 93#
To quickly disconnect........ **
• OGM ONLY MODE
Turn on ............................. 11#
Turn off ............................. 12#
• PLAYBACK
Play messages ................. 7#
Move backward/repeat...... 2#
Skip forward...................... 5#
Stop .................................. 0#
Play new messages only .. 6#
(first stop playback)
• ERASING MESSAGES
Erase single message ...... 3#
Erase all messages .......... 33#
• RECORDING A MEMO
Start .................................. * #
End ................................... 0#
• RECORDING A NEW OGM
Start .................................. 4 *
all.bookPage132Friday,May31,20029:49AM
all.bookPage133Friday,May31,20029:49AM
END USER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharp
brand product (the "Product"), when shipped in its original container, will be free from defective
workmanship and materials, and agrees that it will, at its option, either repair the defect or replace
the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded
item(s) set forth below nor to any product the exterior of which has been damaged or defaced,
which has been subjected to misuse, abnormal service or handling, or which has been altered or
modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set
forth below and provided proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and
exclusive of, all other warranties, express or implied. Specifically, ALL OTHER WARRANTIES
OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE,
AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under
applicable state law, implied warranties may not validly be disclaimed or excluded, the duration of
such implied warranties is limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties
other than those described above, or to extend the duration of any warranties beyond the time
period described above on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and
shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the
manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall
constitute full satisfaction of all claims, whether based on contact, negligence, strict liability or
otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects
in the Product which were caused by repairs or attempted repairs performed by anyone other than
an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or
consequential economic or property damage. Some states do not allow limits on warranties or on
remedies for breach in certain transactions; in such state the limits herein may not apply.
Your Product: Personal Facsimile UX-CC500
Warranty Period for this Product:
Ninety (90) days parts and labor from date of purchase.
Additional items excluded
Any consumable items such as paper or Imaging Film supplied with
from warranty coverage:
the Product.
What to do to obtain service:
Call Sharp at 1-877-794-8675 to obtain a Return Authorization Number and
shipping instructions. A technician will troubleshoot your problem with you
on the phone and if it is determined that your Product needs service, you
will have your choice of having your unit repaired or replaced to any U.S.
location. Be sure to have Proof of Purchase available.
For product information or customer assistance, please visit http://www.sharpusa.com on the
World Wide Web or call 1-877-794-8675.
SHARP ELECTRONICS CORPORATION
Sharp Plaza,
Mahwah, New Jersey 07430-2135
all.bookPage135Friday,May31,20029:49AM
IMPORTANT SERVICE INFORMATION
If a Problem Occurs
Most operational questions can be answered by referring to this "Setup Guide and Operation Manual"
Also, for your convenience, you will find answers to most frequently asked
questions on our website at www.sharpusa.com/, or by sending e-mail to faxsupport@sharpsec.com.
Should you require further assistance, call 1-877-794-8675; a Customer Relations Specialist will
assist you. Before your call, please be ready to provide the model number of your product, serial
number, date of purchase, description of the problem, and a valid credit card number (should it be
required).
How Exchange is Obtained
A replacement unit in exchange for your fax is provided by Sharp to any U.S. location. You will be
required to provide consent for acceptance of an exchange unit and provide credit card authorization.
At that time, Sharp will ship to you, at no cost, an exchange for your defective product. The exchange
unit we ship to you will be new or remanufactured. Upon your receipt of the exchange unit, packaging
and shipping instructions will be enclosed for you to return the defective unit. Upon Sharp's receipt of
the defective unit, your credit card hold will be released.
How Warranty Repair Service is Obtained
If you prefer that we repair your unit instead of replacing it, our Customer Relations Specialists at 1-
877-794-8675 will explain how to obtain warranty repair service. Please be sure to retain the
original packaging materials in order to facilitate shipment. Upon repair of your unit, Sharp will
promptly return it at no cost to you at any U.S. location.
What You Must Do
Your Product is designed to perform with a minimum amount of user maintenance. However, you are
responsible for the required user maintenance described in the "Operation Manual". This requires user
maintenance including replacement of the imaging film and battery, cleaning of the unit and removal
of dust and foreign matter, clearing of paper misfeeds, and proper routine and preventive maintenance.
Service After Expiration of Warranty Coverage
Should you require service repair after warranty coverage has expired, contact Sharp at 1-877-794-
8675 for information.
To Purchase Consumables From Sharp
Visit www.sharpplace.com/ or call Sharp at 1-877-794-8675 to order replacement Sharp Thermal
Ribbons & Accesories. Before your call, please be ready to provide the model number of your
product, and a valid credit card number. Consumables may also be obtained through your reseller.
all.bookPage136Friday,May31,20029:49AM
all.bookPage137Friday,May31,20029:49AM
PRINTED IN THAILAND
(TINSE4273XHTZ)
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
http://www.sharpusa.com
SHARP CORPORATION
FOR YOUR RECORDS
Please record the model number and serial number below, for easy
reference, in case of loss or theft. These numbers are located on the
rear side of the unit.Space is also provided for other relevant
information.
Model Number UX-CC500
Serial Number
Date of Purchase
Place of Purchase
all.bookPage138Friday,May31,20029:49AM
1 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sharp UXCC500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sharp UXCC500 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info