787900
7
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
EN
Memory function
1. If the unit is turned o via the POWER button, when turned back on
again it will resume from the function it was turned o in. Note that if
the timer was set or if the unit was in the lock mode, these settings are
not stored.
2. If the mains power is disconnected while the unit is operating, it will
not start automatically when the mains is reconnected. When the mains
power is applied again, you will need to press the POWER button to
restart operation. The unit will start up in the initial mode.
Water tank full auto-stop function
When the water tank is full, the unit will stop operation, the air outlet
louver will close and a buzzer will sound. To reset, remove the water tank,
empty and replace. When the empty water tank is put back into the unit, it
will restart. Note that the compressor will take about 3 minutes to operate.
Auto defrost
If the unit is used in a low temperature environment, the internal
evaporator may be covered by frost. In order to make sure the machine
operates normally, the machine has auto-defrost function. Should
the internal sensor detect a temperature of ≤-1°C the machine will
enter auto-defrost function. That means it will run continuously in the
dehumidication mode for 30 minutes, then the machine will start the
defrost cycle, the DEFROST light will illuminate, the compressor will stop
and that fan will operate at high speed.
When temperature of evaporator is ≥2°C and the unit has been in the
defrost mode for 10 minutes, the auto-defrost mode will turn o and the
compressor turns on. At this point the unit will start to dehumidify and the
DEFROST light will turn o.
While in the defrost mode and the temperature of the evaporator is ≥0°C
for two minutes, the defrost function is cancelled.
Compressor protection function
Should there be a problem with the unit causing the compressor to stop,
the compressor will turn o for 3 minutes. Normally the compressor will
restart after 3 minutes, if it does not unplug the unit for an hour and try
again. If it still does not start, call for service.
High/Low temperature protection
function
If the unit detects that the ambient temperature is outside of the normal
operating range of 5°C to 38°C, it will shut down. When the normal
operating range is reached, the compressor will start. Note that it will take
the compressor 3 minutes to start working once the normal temperature
range is met.
Low humidity protection function
If the unit detects low humidity of <30% the display will indicate LO and
it will stop any dehumidifying action and the fan will operate a the lowest
speed.
If the humidity is over 80%, the display will indicate HI and keep
dehumidifying.
High temperature fan speed switch
function
When the unit is dehumidifying in a high temperature environment and
the fan speed is set to low, it will switch automatically to the high speed.
This is to prevent excessive load on the compressor. When the ambient air
temperature reduces, the fan speed will return to the low setting.
Error codes
There are number of error codes which may appear in the display, these are
as below. When the error code is displayed, it will ash. If any of these error
codes are experienced, call for service.
C1 – Indicates that there is a fault with the evaporator temperature sensor.
In this condition, the unit will stop working.
C2 – Indicates that there is a fault with the ambient air temperature sensor.
In this condition, the unit will stop working.
C8 – The temperature of the evaporator checked every 8 minutes, if this is
within ≤3°C of the ambient air temperature for 5 consecutive checks, the
unit will shut down and the error code C8 is displayed.
Continuous drainage function
Should it be necessary to provide continuous drainage, this can be
achieved by tting a 15mm inner diameter pipe to the drainage hole on
the rear of the unit. When installed, water will drain through the pipe and
not into the water tank.
Ensure that the drainage pipe runs in a downwards direction, and it not
bent or damaged in any way so that the water runs freely out of the unit.
When tting the drainage pipe, make sure that it is pushed all the way into
the drainage hole so that it pushed over the drain outlet which is located
about 70mm inside the unit from the rear cover of the unit.
Refer to the 3 on page 1 for the location of the drainpipe connection port.
Maintenance
When cleaning your dehumidier:
Use a soft clean cloth.
Do not use the alcohol, gasoline, and other benzene chemical solvents.
To clean the lter, remove it, then use a vacuum cleaner to clear any dust
which may have built up. If necessary, use water to clean, then place it in
ventilated area until dry.
Unplug the unit from the mains supply before cleaning.
Other advice:
Before moving the unit, unplug the mains supply and pull out the water
in tank.
If not using the unit for a long time, unplug the unit from the mains sup-
ply, empty the water tank, wait for 2 days to make sure the unit inside
completely dry before packing.
Always store the unit in an upright position.
Do not tilt the unit horizontally or turn upside down.
If the unit requires repair, seek help of a professional person.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sharp UD-P20E-W bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sharp UD-P20E-W in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 2.36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info