13269

Sharp LC-15L1U-S Operation Manual Handleiding

66
Verklein
Vergroot
Pagina terug
1/69
Pagina verder
LC-15L1U
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
TELEVISOR DE CRISTAL
LÍQUIDO
LC-15L1U
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACIÓN
MANUAL DE OPERAÇÃO
ENGLISH
FRANÇAIS
ESPAÑOL
PORTUGUÊS
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
Printed on 100% post-consumer recycled paper.
Imprimé sur 100% de papier recyclé.
Impreso en 100% de papel reciclado de postconsumo.
Papel 100% Reciclado-Cuidado do Meio Ambiente.
Printed in Japan
Imprimé au Japon
Impreso en Japón
Impresso no Japão
TINS-B124WJZZ
04P02-###
ENGLISH
1
LC-15L1U
LIQUID CRYSTAL TELEVISION
OPERATION MANUAL
ENGLISH
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within a triangle is intended to
alert the user to the presence of important operating
and maintenance (servicing) instructions in the
literature accompanying the product.
IMPORTANT:
To aid reporting in case of loss or theft, please record the TV’s model
and serial numbers in the space provided. The numbers are located at
the rear of the TV.
U.S.A. ONLY
Model No.:
Serial No.:
2
IMPORTANT INFORMATION (Continued)
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user’s authority to operate this equipment.
“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical
Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.”
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
U.S.A. ONLY
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these
materials may be regulated due to environmental considerations. For disposal or recycling information, please contact
your local authorities or the Electronic Industries Alliance: www.eia.org
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the operation manual, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
The device’s label or the user manual contains this statement (or equivalent): “To prevent radio interference to the
licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding.
Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.”
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
ENGLISH
3
CONTENTS
Page
IMPORTANT INFORMATION................................... 1
DEAR SHARP CUSTOMER ..................................... 4
IMPORTANT SAFETY PRECAUTIONS .................. 4
REGARDING BATTERY CARE ............................... 7
CORRECT USE OF THE PRODUCT ....................... 9
SUPPLIED ACCESSORIES ................................... 10
PREPARATION....................................................... 11
MAIN UNIT PART NAMES ..................................... 14
WIRELESS CENTER PART NAMES ..................... 17
REMOTE CONTROL .............................................. 18
POWER ................................................................... 19
Turning the Main Power on and off .................. 19
Viewing with a Home AC Wall Outlet ............... 21
EZ SETUP (WITH AUTO CLOCK SETTING) ........ 22
EZ Setup during the First Power On ................ 22
SETTING THE CLOCK ........................................... 24
AUTO CLOCK Setting ....................................... 24
MANUAL CLOCK Setting.................................. 26
TV SIGNALS IN YOUR REGLON .......................... 27
BATTERY CHARGE AND TRANSMISSION
SETTING .............................................................. 28
Battery Charge .................................................. 28
Transmission Setting ......................................... 28
BASIC OPERATION ............................................... 31
Turning on Power .............................................. 31
Standby.............................................................. 31
Switching TV/VIDEO [AV1/AV2/AV3/AV4]
Modes ............................................................. 32
Sound Volume ................................................... 33
Changing Channels ........................................... 34
SELECTING MENU ITEMS .................................... 35
ADJUSTMENTS ...................................................... 36
Adjusting SLEEP TIMER Settings .................... 36
Adjusting BRIGHTNESS Settings ..................... 37
Adjusting PICTURE FLIP Settings.................... 38
Adjusting PRESET Settings .............................. 39
Adjusting LANGUAGE Settings ........................ 40
Adjusting VIDEO ADJUST Settings .................. 41
SETUP ............................................................... 43
Adjusting BLUE SCREEN Settings................... 45
Adjusting CLOSED CAPTION Settings ............ 46
Adjusting V-CHIP Settings ................................ 47
CONNECTION SYSTEM WITH VARIOUS WAYS
OF BEING USED ................................................. 54
Examples of Various Uses ................................ 54
Connecting System Chart of LC-15L1U ........... 55
Method of Connecting External Equipment ...... 56
Method of Using the Video Controller .............. 57
Watching Played back Image from External
Equipment....................................................... 58
Connecting a Home Video Game System, etc.
(AV-IN4) .......................................................... 59
How to Use Video 1 Output .............................. 60
Monitor Output for Picture and Sound Output
from AV-IN2/OUT Terminal ............................ 61
TROUBLESHOOTING ............................................ 62
SPECIFICATIONS................................................... 65
DIMENSIONAL DRAWINGS .................................. 66
CALLING FOR SERVICE ....................................... 67
LIMITED WARRANTY ............................................ 67
Page
4
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years
of trouble-free operation of your product, please read the Important Safety Precautions carefully before
using this product.
IMPORTANT SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if
improperly handled. This product has been engineered and manufactured with the highest priority on safety. However,
improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following
instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your
LCD color TV product, please read the following precautions carefully before using the product.
■ Read instructions—All operating instructions must be read and understood before the product is operated.
■ Keep this manual in a safe place—These safety and operating instructions must be kept in a safe place for future
reference.
■ Observe warnings—All warnings on the product and in the instructions must be observed closely.
■ Follow instructions—All operating instructions must be followed.
■ Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attachments
can result in accidents.
■ Power source—This product must operate on a power source specified on the specification label. If you are not
sure of the type of power supply used in your home, consult your dealer or local power company. For units
designed to operate on batteries or another power source, refer to the operating instructions.
■ Power cord protection—The power cords must be routed properly to prevent people from stepping on them or
objects from resting on them. Check the cords at the plugs and product.
■ If the AC adapter is misplaced or needs to be replaced, obtain the same type of adapter from a SHARP service
center or your dealer.
■ Overloading—Do not overload AC outlets or extension cords.
Overloading can cause fire or electric shock.
■ Entering of objects and liquids—Never insert an object into the product through vents or openings. High voltage
flows in the product, and inserting an object can cause electric shock and/or short internal parts. For the same
reason, do not spill water or liquid on the product.
■ Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high voltage and
other dangerous conditions. Request a qualified service person to perform servicing.
■ Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a quali-
fied service person to perform repairs.
a.When the power cord or plug is damaged.
b.When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d.When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of
controls not described in the instructions can cause damage, which often requires extensive adjustment work by
a qualified technician.
e.When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the
product needs servicing.
■ Replacement parts—In case the product needs replacement parts, make sure that the service person uses
replacement parts specified by the manufacturer, or those with the same characteristics and performance as the
original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.
■ Safety checks—Upon completion of service or repair work, request the service technician to perform safety checks
to ensure that the product is in proper operating condition.
■ Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product according
to the method recommended by the manufacturer.
■ Polarization—This AC adapter may be equipped with a polarized alternating current line plug (a plug having one
blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
ENGLISH
5
IMPORTANT SAFETY PRECAUTIONS (Continued)
■ The Liquid Crystal panel is a very high technology product with 921,600 thin film transistors, giving you fine picture
details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.
Please note that this does not affect the performance of your product.
■ Cleaning—Unplug the power cord from the AC outlet before cleaning the prod-
uct. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol
cleaners.
■ Water and moisture—Do not use the product near water, such as bathtub,
washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement.
■ Stand—Do not place the product on an unstable cart, stand, tripod or table.
Placing the product on an unstable base can cause the product to fall, resulting
in serious personal injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the
product. When mounting the product on a wall, be sure to follow the manufactur-
er’s instructions. Use only the mounting hardware recommended by the manu-
facturer.
■ When relocating the product placed on a cart, it must be moved with utmost
care. Sudden stops, excessive force and uneven floor surface can cause the
product to fall from the cart.
■ Ventilation—The vents and other openings in the cabinet are designed for
ventilation. Do not cover or block these vents and openings since insufficient
ventilation can cause overheating and/or shorten the life of the product. Do not
place the product on a bed, sofa, rug or other similar surface, since they can
block ventilation openings. This product is not designed for built-in installation; do
not place the product in an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer’s instructions are followed.
■ The Liquid Crystal panel used in this product is made of glass. Therefore, it can
break when the product is dropped or applied with impact. Be careful not to be
injured by broken glass pieces in case the Liquid Crystal panel breaks.
■ Heat sources—Keep the product away from heat sources such as radiators,
heaters, stoves and other heat-generating products (including amplifiers).
6
IMPORTANT SAFETY PRECAUTIONS (Continued)
■ If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to
provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical
Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.
■ Power Lines – An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits
as contact with them might be fatal.
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC—NATIONAL ELECTRICAL CODE
GROUND
CLAMP
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
■ Lighting – For added protection for this television equipment during a lightning
storm, or when it is left unattended and unused for long period of time, unplug it
from the wall outlet and disconnect the antenna. This will prevent damage to the
equipment due to lightning and power-line surges.
■ To prevent fire, never place any type of candle or naked flames on the top or
near the TV set.
■ To prevent fire or shock hazard, do not expose this products to dripping or
splashing. No objects filled with liquids, such as vases, should be placed on the
products.
ENGLISH
7
REGARDING BATTERY CARE
• Charge the battery only at temperatures within the range of
50°F to 86°F (10°C to 30°C) (temperatures that are comfort-
able for people). At lower temperatures it becomes more
difficult to charge the battery and the battery deteriorates. It is
not possible to sufficiently charge the battery at high tempera-
tures.
• The battery may become hot during charging or during use,
but this is not a sign of malfunctioning.
• It may take more time to fully charge a hot battery.
Precautions to be Taken during Charging
Regarding Operating Time and Use under Low Temperatures for the Battery
• The battery has a certain life expectancy. The battery is
consumed as time elapses even if the battery is not used. A
battery that has been used for about a year may give you less
operating time depending on the conditions under which it
was stored. If a battery that has been charged correctly
operates for a much shorter time than usual, it has reached
the end of its life and must be replaced with a new battery.
• When the battery is at a low temperature (lower than 50°F
(10°C)) in winter, the operating time may be very short. The
battery undergoes an internal chemical reaction in order to
generate electricity. When the temperature outside is lower,
the chemical reaction becomes less vigorous and operating
time becomes shorter.
How to Get the Most out of the Battery
• Turn off the power supply frequently when not in use in order to give the battery longer life.
• The battery is consumed as time elapses even if the battery is
not used. To prevent consumption;
(1) If the battery will not be used for a long time, use the
product to run down what is left of the battery charge and
set “Battery charge” to “off” in the menu screen. (Refer to
page 28.)
(2) Make sure to use the battery at least once every six
months.
Storage Precautions
Charge the battery before use.
Battery type lithium-ion battery
Nominal voltage 11.1 V
Battery capacity 5700 mAh
Operating temperature 50°F to 86°F (10°C to 30°C)
Maximum dimensions appx. Length 8
23
/64 inch (212 mm) × Width 1
5
/8 inch (41 mm) × Height 1
35
/64 inch (39 mm)
Weight appx. 1.1 lbs. (0.5 kg)
• The battery used in the product is a lithium-ion battery. Even if
the battery is charged and stored, the amount of charge in the
battery will drop.
• Make sure to charge the battery until the charge indicator of
the product goes off (fully charged). The operating time is
shortened when using a battery which has not been fully
charged. (For a detailed description of how to charge the
battery, refer to page 20.)
Battery Specification
8
REGARDING BATTERY CARE (Continued)
Prohibited use for which safety is not guaranteed.
• Do not try to disassemble or modify the battery. The battery
contains safety mechanisms and protection devices.
Damaging these safety devices may cause the battery to
generate heat or smoke, or to rupture or ignite.
• Do not connect the + and – terminals together with metal
such as wires. Do not carry or store the battery together
with metal objects such as necklaces and hairpins. Doing
so may cause the battery to be short-circuited so as to
cause an extremely large amount of electric current to flow,
which may cause the battery to generate heat or smoke,
rupture or ignite, or may cause metal objects such as wire,
necklaces, or hairpins to heat up.
• Do not expose batteries to fire or heat. Doing so may cause
insulating materials to melt, damage gas exhaust valves or
safety mechanisms, or ignite electrolytic solutions, which
may cause the battery to generate heat or smoke, rupture
or ignite.
• Do not leave the battery in or near fire, stoves, or other
high-temperature locations (of temperatures greater than
140°F (60°C)). If a resin separator is damaged by heat, the
battery may become internally short-circuited and this may
cause the battery to generate heat or smoke, rupture or
ignite.
• Do not expose the battery to water or salt water, or allow
the battery to get wet. If the protection device contained in
the battery is broken, this may cause the battery to gener-
ate heat or smoke, rupture or ignite.
• Do not charge the battery near a fire or in direct sunlight. If
the battery becomes hot, the protection device for prevent-
ing danger operates to disable the battery from being
charged. If the protection device contained in the battery
becomes broken, the battery is charged at an abnormal
electric current or voltage. An abnormal chemical reaction
occurs inside the battery which may cause the battery to
generate heat or smoke, rupture or ignite.
• Charge the battery in compliance with the specified charg-
ing conditions. If the battery is charged without compliance
to the charging conditions (at temperatures greater than the
specified temperature, at voltages and electric current
greater than the specified amount or with modified charg-
ers), the battery may be overcharged or charged at an
abnormal electric current and an abnormal chemical
reaction may occur inside the battery, which may cause the
battery to generate heat or smoke, rupture or ignite.
• Do not pierce the battery with nails, strike the battery with a
hammer, or step on the battery. Doing so may cause the
battery to generate heat or smoke, rupture or ignite.
• Do not subject the battery to strong impacts or throw it
away. If the protection device contained in the battery
becomes broken, the battery is charged at an abnormal
electric current or voltage. An abnormal chemical reaction
may then occur inside the battery, which may cause the
battery to generate heat or smoke, rupture or ignite.
• Do not use the battery if it has been considerably damaged
or deformed. This may cause the battery to generate heat
or smoke, rupture or ignite.
• Do not solder directly onto the battery. Doing so may cause
insulating materials to melt, or damage gas exhaust valves
or the safety mechanism, which may cause the battery to
generate heat or smoke, rupture or ignite.
• Use a battery case when carrying the battery.
• Keep the battery out of reach of children.
• In the event that the fluid inside the battery gets into one’s
eye, do not rub the eye because this may cause loss of
eyesight. Rinse the eye with clean water and consult a
doctor immediately. In the event that the fluid becomes
attached to skin or clothes, wash it off with clean water
immediately as this may cause injury.
ENGLISH
9
CORRECT USE OF THE PRODUCT
Precautions Regarding Radio Waves
■ Do not use the product at the following locations. There may be cases where noise occurs or transmission/reception is
not possible.
• Locations where magnetic fields, electrostatic or interference occurs due to devices such as Bluetooth, wireless LANs, or
microwave ovens etc. that utilize the same frequency band (2.4 GHz) as the product. (There may be cases where radio waves
cannot reach depending on the environment.)
• Keep the product away from a radio devices during use. (There may be cases of noise interference.)
■ Under the same frequency band as the product uses, in addition to Bluetooth, wireless LANs, and microwave ovens
etc. that utilize the same frequency band (2.4 GHz) as the product, operation can also take place at on-site radio
stations that require a license for mobile object identification used in factories and manufacturing lines etc. and
specified low power radio stations.
• Before using the product, make sure that there is no on-site radio stations for mobile object identification or specified low power
radio stations operating in the vicinity of the product.
• If there is any interference occurring to on-site radio stations for mobile object identification due to the product, stop using the
product immediately.
Regarding Range of Usage
■ The product is limited to domestic use.
(There is a possibility that transmission distance may become short depending on the communication environment.)
■ In the following cases, reception may become bad or impossible, which may cause sound and pictures to be inter-
rupted (pictures and sound are stopped), or blocks of noise to appear.
• Using the product in a reinforced concrete building such as a condominium building or a house of a metal structure.
• Using the product at locations near large-scale metallic furniture.
• Using the product in a crowd of people or close to buildings or obstacles, etc.
• Using the product at locations where magnetic fields, electrostatic and interference occur due to devices such as Bluetooth,
wireless LANs, or microwave ovens, etc. that utilize the same frequency band (2.4 GHz) as the product.
■ Regarding reflected radio waves
• Radio waves that reach a television receiver are radio waves (direct waves) directly transmitted from a transmitter and radio
waves (reflected waves) arriving from various directions as a result of being reflected by walls, furniture, or buildings etc. There
are good and bad positions in terms of wave conditions due to the influence of these reflected waves, which may cause poor
picture reception. In this case, try changing the location of the TV receiver slightly. There are cases where pictures and sound
are distorted or interrupted due to the reflected waves as a result of a person passing over or approaching between the transmit-
ter and the television receiver.
When a signal other than a regular signal is input
• When a signal other than a regular signal that is incompatible with this unit is input, the screen may freeze, but this is not a
malfunction.
• When a signal other than a regular signal is input from the Antenna, AV-IN1, AV-IN2, or AV-IN3 terminals, reception may be bad
depending on the performance of the Wireless Center, and the message “THIS SIGNAL IS NOT COMPATIBLE” will display.
• Signals compatible with the Wireless Center are as follows:
H: 15.625 kHz / V: 50.0 Hz, 59.52 Hz
H: 15.73426 kHz / V: 59.94 Hz
(Note: Reception may be available with AV-IN4.)
Precaution Regarding Electromagnetic Wave Disturbance
• If electric devices, such as a cellular phone, are used near this unit, electromagnetic wave disturbance may occur between
apparatus. In such cases, the picture quality may decrease and noise may appear.
10
SUPPLIED ACCESSORIES
Confirm that the following accessories are provided with the product.
Wireless remote control (×1), Remote control holder (×1),
“AAA” size (UM/SUM-4) dry batteries (×2)
Wireless Center (×1), Wireless Center stand (×1)
Battery (×1)
AC adapters (×2)
Cable clamps (×2), Table stand (×1)
*Product shape varies in some countries.
Screws (×3)
(See pages 11, 15, 18) (See page 19)
(See pages 13, 21)
(See page 17)
(See page 59)
(See pages 55, 57, 60)
Terminal cover
SIGNAL LEVEL
MAIN
POWER
POWER
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
TELEVISOR DE CRISTAL
LÍQUIDO
LC-15L1U
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACIÓN
MANUAL DE OPERAÇÃO
ENGLISHFRANÇAISESPAÑOLPORTUGUÊS
Manuals
Video controller (×1)
(See page 12)
Antenna cables (×2)
RRMCGA152WJSA
LHLDZA216WJZZ
UBAT1A011WJZZ
GDAI-A074WJSA
TINS-B124WJZZ
QCNWGA033WJPZ
QCNWG0003CEPA
Connecting System Chart of
LC-15L1U
TCAUZA072WJZZ
Registration Card
TCAUDEA028WJZZ
Caution Sheet
TCAUZA071WJZZ
LHLDW0109CESA
(See page 15) CDAI-A072WJ02
QACCDA023WJPA × 2 pcs
UADP-A042WJPZ
UADP-A041WJPZ
QCNWG0004CEZZ
ENGLISH
11
PREPARATION
Using the Remote Control
■ Use the remote control by pointing it toward the remote control sensor window
on the main unit. Objects between the remote control and sensor window may
prevent proper operation.
Cautions regarding use of the remote control
■ Do not expose the remote control to shock.
In addition, do not expose the remote control to liquid, and do not place it in an
area with high humidity.
■ Do not install or place the remote control under direct sunlight. The heat may
cause deformation of the unit.
■ The remote control may not work properly if the remote control sensor window
of the main unit is under direct sunlight or strong lighting. In such cases,
change the angle of the lighting or LCD TV set, or operate the remote control
closer to the remote control sensor window.
Batteries for the Remote Control
Before using the LCD TV set for the first time, install two (“AAA” size, UM/SUM-4) batteries (supplied). When the batter-
ies become depleted and the remote control fails to operate, replace the batteries with new (“AAA” size, UM/SUM-4)
batteries.
1
Open the battery cover.
■ Slide the cover while pressing the
(b) part.
2
Insert two (“AAA” size, UM/SUM-
4) batteries.
+
–
+
–
■ Position the positive and negative
ends of the batteries as indicated in
the compartment.
Caution!
Cautions regarding batteries
Improper use of batteries can result in chemical leakage and/or explosion. Be sure to follow the instructions below.
• Place batteries with their terminals corresponding to the (+) and (–) as indicated in the compartment.
• Different types of batteries have different characteristics. Do not mix batteries of different types.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new battery and/or cause the old
battery to leak chemicals.
• Remove batteries when they become weak.
Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe with a cloth.
• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.
• If the remote control will not be used for an extended period of time, remove the batteries from the remote control.
SLEEP indicator
CHARGE indicator
POWER indicator
Remote sensor window
CHARGE SLEEPPOWER
3
Close the battery cover.
■ Engage the claw on the cover into
the battery housing and slide shut.
12
F-type connector
75-ohm coaxial cable
Antenna Connection
PREPARATION (Continued)
OUTDOOR ANTENNA CONNECTION
• Use one of the following two diagrams if you connect an outdoor antenna.
A: Using a VHF/UHF combination outdoor antenna
B: Using separate VHF and/or UHF outdoor antennas
• Connect the outdoor antenna cable lead-in to ANT. (Antenna terminal) on the rear of the Wireless Center.
F-type connector
75-ohm coaxial cable (round)
300-ohm twin-lead cable (flat)
1. A 75-ohm system is generally a round cable with F-type connector that can easily be
attached to a terminal without tools (not supplied).
2. A 300-ohm system is a flat “twin-lead” cable that can be attached to a 75-ohm terminal
through a 300-75-ohm adapter (not supplied).
ANTENNAS
• The antenna requirements for good color television reception are more important than those for black & white television reception.
For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connections that are provided with the various antenna systems.
NOTICE
F-type connector should be finger-tightened only.
When conecting the RF cable to the TV set, do not tighten F-type
connector with tools.
If tools are used, it may cause damage to your TV set.
(The breaking of internal circuit, etc.)
Wireless Center
IN
OUT
AV-IN1AV-IN1AV-IN3
IR
OUT
POWER
INPUT
DC12V
FACTORY
SERVICE
S-VIDEO
MONITOR
OUT
MONITOR
OUT
VIDEO
AUDIO
L
AUDIO
R
AV-IN2
/OUT
ANT.
TV/VCR/DVD, etc.
TV
VCR
DVD
75-ohm
coaxial cable
Antenna cable
300-ohm
twin-lead
VHF/UHF
antenna
VHF/UHF
antenna
300/75-ohm
adapter
(not supplied)
300-ohm
twin-lead
300-ohm
twin-lead
75-ohm
coaxial cable
OUTIN
VHF
antenna
UHF
antenna
Combiner
(not supplied)
or
or
B: Separate VHF and/or UHF antennas
A: Combination VHF/UHF antenna
ENGLISH
13
Antenna Connection (Continued)
PREPARATION (Continued)
Cable TV converter/
descrambler
(not supplied)
Two-set
signal
splitter
(not
supplied)
Cable TV line
RF switch (not supplied)
OUT
IN
• A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75-ohm coaxial cable to the
set, screw the 75-ohm cable to the ANT. terminal.
• Some cable TV companies offer “premium pay channels”. Since the signals of these premium pay channels are scram-
bled, a cable TV converter/descrambler is generally provided to the subscriber by the cable TV company. This converter/
descrambler is necessary for normal viewing of the scrambled channels. (Set your TV to channel 3 or 4, typically one of
these channels is used. If this is unknown, consult your cable TV company.) For more specific instructions on installing
cable TV, consult your cable TV company. One possible method of utilizing the converter/descrambler provided by your
cable TV company is explained below.
Please note: An RF switch provided with two inputs (A and B) is required (not supplied).
“A” position on the RF switch (not supplied): You can view all unscrambled channels by using the TV’s channel keys.
“B” position on the RF switch (not supplied): You can view the scrambled channels via the converter/descrambler by using
the converter’s channel keys.
CABLE TV (CATV) CONNECTION
Note:
• Consult your SHARP Dealer or Service Center for the type of splitter, RF switch or combiner that might be required.
Power Connection
Connect to the DC input terminal of each product.
Note:
• Always turn the MAIN POWER button of the LCD TV set and the power button of the Wireless Center to OFF when connecting the AC
adapters.
• If there is a Sharp product close to the video controller, the product may malfunction during transmission of the video controller.
• Unplug the AC adapters from the LCD TV set, Wireless Center unit and AC wall outlet when the LCD TV set is not to be used for a
long period of time.
AC wall
outlet
AC adapter
AC cord
TV main unit
AC wall
outlet
AC adapter
AC cord
IR
OUT
POWER
INPUT
DC12V
FACTORY
SETTING
Wireless
Center
14
MAIN UNIT PART NAMES
Numbers in indicate the main pages where the corresponding item is described in this manual.
CHARGE indicator
POWER indicator
Remote sensor windowTable stand (Detachable)
Left speaker
Right speaker
15
SLEEP indicator
36
20
22
11
Main unit (Top view: Control section)
Main unit (Front view)
CHVOL MENU TV/VIDEO MAIN POWER
-
+
VOL (–)/(+)
CH ( )/( )
MAIN POWER
TV/VIDEO
MENU
33
34
35
32
31
ENGLISH
15
MAIN UNIT PART NAMES (Continued)
Main unit (Rear view)
AUDIO
AV- IN4
VIDEO
S-VIDEO
HEAD
PHONE
FACTORY
SERVICE
L
R
CHCH
ENTER
P
O
WE
R
DISPLAY
SLEEP PIC. FLIP
MUTE
VOL
BRIGHT TV/VIDEO MENU
FLASH
BACK
MTS
POWER INPUT DC 15 V
HEADPHONE jack
S-VIDEO
VIDEO
AV-IN4
AUDIO(R)
AUDIO(L)
Remote control holder
The remote control can be placed in the
remote control holder when moving the TV.
1 Attach the remote control holder to the
handle with the arrow ( ) in the center of
the holder facing upward.
2 Place the remote control in the remote
control holder.
Table stand
release button
Handle
1
2
CHCH
ENTER
POWER
DISPLAY
SLEEP PIC. FLIP
MUTE
VOL
BRIGHT TV/VIDEO MENU
FLASH
BACK
MTS
Removing and Attaching the Table Stand
1
Lift the main unit straight up by holding the handle while depressing the table
stand release button.
2
Unfold the stand.
• Securely unfold the stand until you hear a clicking sound. Only use the
stand after first unfolding until a clicking sound is heard to ensure that it is
stable.
3
Fold up the stand.
• Return the stand to its original unfolded position.
4
Insert the main unit straight into the table stand.
• The main unit cannot be inserted if inclined on an angle. Inserting the main
unit with force can cause damage or a malfunction.
Stand
Handle
Table stand
release button
Table stand
16
MAIN UNIT PART NAMES (Continued)
Removing the Back Cover
■ Before connecting cables and cords to the rear terminals, remove the back covers. Push
in the tabs and pull out the back covers carefully.
■ To mount the cover, insert the 2 hooks on the bottom of the cover into the cabinet and
press on the upper part of the back cover until the tab locks in place with a click.
Listening with Headphones
■ Plug the headphone mini-plug into the HEADPHONE jack located on the rear of the TV set.
Note:
• Headphones are not included in the supplied accessories.
• No sound is heard from the main unit speakers when a headphone mini-plug is connected into the HEADPHONE jack.
▼ On-screen display
Adjust the sound volume
using VOL (e)/(f) on the
remote control.
Headphones
AUDIO
AV-IN4
VIDEO
S-VIDEO
L
R
HEAD
PHONE
Rear terminal
20
VOLUME
ENGLISH
17
WIRELESS CENTER PART NAMES
SIGNAL LEVEL
MAIN
POWER
POWER
IN
OUT
AV-IN1AV-IN1AV-IN3
IR
OUT
POWER
INPUT
DC12V
FACTORY
SERVICE
S-VIDEO
MONITOR
OUT
MONITOR
OUT
VIDEO
AUDIO
L
AUDIO
R
AV-IN2
/OUT
ANT.
Transmission
SIGNAL LEVEL
indicator
(Reception gain)
· Green:
Communication
in progress
· Red:
Difficulty
in transmission
· Not lit:
Not communicating
POWER indicator
· Green:
Operation in
progress
(when power is on)
· Red: Standby
MAIN
POWER
button
Front
Antenna
input
terminal
Antenna
output
terminal
Rear
VIDEO
AUDIO (L)
AUDIO (R)
AV-IN1 (S-VIDEO)
MONITOR
OUT
MONITOR OUT
(S-VIDEO)
Factory
adjustment
terminal
POWER INPUT
DC 12V
Video control
terminal
VIDEO
AUDIO (L)
AUDIO (R)
AV-IN1
VIDEO
AUDIO (L)
AUDIO (R)
AV-IN3
VIDEO
AUDIO (L)
AUDIO (R)
AV-IN2
/OUT
Wireless Center
TV main unit
Wireless Center
stand
Rubber foot
Rubber foot
POWER Indicator
When the TV is turned off with the remote control, the
Wireless Center is switched to standby (POWER indicator
is lit red). (There may be a time lag of about 5 to 6
seconds.)
Placing the Wireless Center Where You Want It
We recommend placing the Wireless Center in an area
where there are no obstructions to impede radio wave
transmission/reception.
(Do not place the Wireless Center in a box.)
Note:
• The distance for which transmission is possible between the
main unit and Wireless Center is about 15 metres. However,
this distance may vary depending on the location or
conditions under which the Wireless Center is used.
• If the main unit gets close to the Wireless Center, there may
be cases where noise appears on the screen. In this case,
keep the main unit away from the Wireless Center until the
noise decreases, or try to change the transmission channel
setting (page 28).
Setting up the Wireless Center
• The Wireless Center can be placed horizontally or upright.
• When placing horizontally:
The side on which the rubber feet are attached is the
bottom.
• When placing upright:
Fasten the stand to the bottom of the Wireless Center with
the screws provided.
* Failure to securely fasten the stand may cause the
Wireless Center to tip over during use.
18
REMOTE CONTROL
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
1 POWER (p. 22)
Switch the Liquid Crystal Television power on or off.
2 DISPLAY
Display the channel and time information.
3 SLEEP (p. 36)
Set the sleep timer.
4 ENTER
Execute a command.
5 BRIGHT (p. 37)
Adjust the brightness of the screen.
6 MUTE (p. 33)
Mute the sound.
7 VOL (+)/(–) (p. 33)
Set the volume.
8 CH ( )/( ) (p. 34)
Select channel.
9 MTS (p. 33)
Select audio settings.
10 PIC. FLIP (p. 38)
Set the orientation of the picture.
11 a/b/c/d (Cursor control) (p. 22)
Select a desired item on the screen.
12 TV/VIDEO (p. 32)
Select a Liquid Crystal Television input source.
13 MENU (p. 35)
Display the menu screen.
14 FLASHBACK (p. 34)
Return to the previous channel.
15 Channel Select (p. 34)
Set the channel.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ENGLISH
19
POWER
Turning the Main Power on and off
See page 15 for how to remove the table stand.
■ Installing the Battery
1
Open the cover of the battery
case.
2
Remove the terminal cover of the
battery.
3
Pack toward the left side first and
then push the battery inside the
compartment.
4
Shift the battery to the right.
• The lever will return to its
original position.
• Move the battery to the right
until the lever returns
completely.
5
Close the cover of the battery
case.
• Align the tabs of the cover with
the corresponding grooves in
the TV and snap into position.
■ When Removing
With the lever pulled forward, lift up on
the battery while pushing to the left.
• Always make sure to attach the
terminal cover to the removed
battery.
Place on a soft cloth.
Cover of the
battery case
Terminal cover
Battery
Lever
Lever
20
■ Charging the Battery
Charge the battery when using for the first time (“BATTERY CHARGE” is set to “ON” (page 28)). Plug the AC adapter into a
wall outlet and the corresponding connector on the TV. The CHARGE indicator lights and charging begins. When charging is
completed, the CHARGE indicator turns off.
Charging while Viewing:
The battery will be charged, while you are viewing if “BATTERY CHARGE” is set to “ON” (page 28). In this case, charging
takes about 12 hours. To preserve battery performance it is recommended that “BATTERY CHARGE” be set to “OFF” if
battery power is not in constant use.
Note:
• Charging time may be longer depending on ambient temperature, battery condition and other factors. Check to make sure the CHARGE
indicator is not lit before using.
General Reference for Battery Viewing Time
The viewing time differs according to the BRIGHTNESS setting
(page 37).
Note:
• Operating time may be shorter depending on certain conditions such
as use in cold climates.
When You Want to Check the Amount of Remaining
Battery Power
Press the DISPLAY button on the remote control.
• Although the remaining battery power indicator will flash red
for the first 10 seconds, it will remain lit constantly after that
time.
• The amount of remaining charge is only displayed when
operating on battery power.
• The remaining battery power indicator changes according to
battery status, temperature and conditions of use. This
indicator should be used as a reference for the amount of
battery power remaining.
When Battery is not Charging Properly
• If the CHARGE indicator begins to flash extremely rapidly during charging, this means that charging is not proceeding
normally.
• When the CHARGE indicator flashes at an interval of about a second during charging, the TV main unit is not in an
appropriate temperature range for charging. The temperature range for charging should be approximately between 50°F
(10°C) and 86°F (30°C).
• If the CHARGE indicator begins to flash extremely rapidly (at about 3 flashes a second) during charging, this means that
charging is not proceeding normally because the battery may malfunction. Replace the battery with the new one.
POWER (Continued)
Viewing Time
about 1.5 hours
about 2 hours
about 3 hours
Remaining
battery
power
indicator
The remaining battery power indicator
changes as shown below when the battery
level becomes low.
(Green) (Green) (Red)
The remaining battery power indicator is
displayed constantly regardless of whether
the on-screen display is on or off when the
battery level is low.
BRIGHTNESS Setting
BRIGHT
NORMAL
DARK
AC adapter
TV main unit
CHARGE
indicator
AC wall outlet
AC cord
ENGLISH
21
Viewing with a Home AC Wall Outlet
Plug the AC adapter of the Wireless Center and AC adapter of the TV main unit into an AC wall outlet.
• Check to make sure that the proper voltages indicated on the products are being used when plugging the AC adapters into
their respective DC terminals.
• If there is a Sharp product close to the video controller, the product may malfunction during transmission of the video
controller.
■ Using the AC Adapter
• Although the AC adapters may become warm during use, this is not a malfunction.
• Do not wrap or cover the AC adapters with a blanket or similar covering. This can cause a malfunction or accident.
• Do not attempt to disassemble or modify the AC adapters. The insides of the AC adapter contain high-voltage components
that can result in the risk of electrical shock.
POWER (Continued)
AC wall
outlet
AC adapter
AC cord
TV main unit
AC wall
outlet
AC adapter
AC cord
IR
OUT
POWER
INPUT
DC12V
FACTORY
SETTING
Wireless
Center
22
EZ SETUP (WITH AUTO CLOCK SETTING)
EZ SETUP during the First Power On
■ When you turn on the TV and the Wireless Center for the first time, it will
automatically memorize the broadcasting channels and clock.
Please perform the following instructions before you press MAIN POWER.
(1) Insert the batteries into the remote control. (See page 11.)
(2) Connect the antenna cable to the Wireless Center. (See page 12.)
(3) Connect the AC adapter to the POWER INPUT terminal of the product and
plug in the AC cord to the wall outlet. (See page 13.)
1
Press MAIN POWER of the TV main
unit.
• The “LANGUAGE” screen with a list of
the languages for the on-screen
display appears.
• The POWER indicator of the TV main
unit turns green.
2
Press MAIN POWER of the Wireless
Center unit.
• The POWER indicator of the Wireless
Center turns green.
3
Press a/b to select “ENGLISH”,
“ESPAÑOL (SPANISH)” or “FRANCAIS
(FRENCH)”, and press ENTER.
4
Press a/b to select “ON” or “OFF”.
When you select “ON”, the TV set will
automatically memorize the broadcasting
channels.
5
Press ENTER to access AUTO CLOCK
mode.
6
Press a/b to select “ON” or “OFF”.
When you select “ON”, the TV set will
automatically search the time signals
(EDS signals), provided by some TV
stations, to adjust the clock. The AUTO
CLOCK setting may take from several
minutes to an hour depending on the
number of channels to receive and
signal status. If you know the channel of
the EDS signal carrier (PBS or other) in
your area, select “OFF” and follow the
procedure in AUTO CLOCK Setting.
(See pages 24, 25.)
7
Press ENTER to access EZ SETUP
mode.
Note:
• If you select “OFF” in “EZ SETUP CH-SETTING”,
EZ SETUP will be canceled.
Control section of main unit
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
ENTER
SELECT LANGUAGE
ENGL I SH
ESPAÑOL
FRANCA I S
SELECT : ENTER: EXIT:
ENTER
MENU
EZ SETUP
ON
AUTO CLOCK
OFF
SELECT : ENTER: EXIT:
ENTER
MENU
EZ SETUP
CH-SETT I NG
ON
OFF
SELECT : ENTER: EXIT:
ENTER
MENU
POWER indicator
1
2
MAIN POWER
POWER indicator
a/b
ENGLISH
23
EZ SETUP (WITH AUTO CLOCK SETTING) (Continued)
START EZ SETUP?
CONNECT ANTENNA OR CABL E.
YES
NO
EXIT:
MENU
SELECT : ENTER:
ENTER
PLEASE
W
AIT
AUTO PROGRA
MM
ING
STOP:
2
STEREO
<
ON A I R
SAP
M
ONO
PLEASE
W
AIT
NO
W
SEARCH ING T IME
STOP:
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
ENTER/
a/b/c/d
EZ SETUP during the First Power On (Continued)
8
Press a/b to select “YES”, and press
ENTER.
If you want to stop the EZ SETUP
process once it has started, press c
and it will be canceled. If you want to
SET UP again, please refer to pages 43
and 44 on “SET UP”.
To cancel EZ SETUP
Press c.
The tuner will automatically search for
the broadcasting and cable TV channels.
(The CH No. will automatically increase
when it appears.)
The TV set will automatically search for
EDS signals.
If EDS signals are received, the channel
number and time will be displayed, and
then the screen shown in step 8
appears.
9
Once EZ SETUP is completed, the
lowest channel number memorized will
be displayed.
Note:
• Do not let the EZ SETUP screen remain unat-
tended for a long time.
• If EZ SETUP does not memorize all the channels
in your region, please refer to pages 43 and 44
for more information on manually memorizing the
channels using CHANNEL SETTING.
• It may be difficult to preset when the broadcasting
signals are weak, the channel cycle frequency is
incorrect or the frequency jamming is occurring
around the area. Please refer to pages 43 and 44
for more information on manually memorizing
channels using CHANNEL SETTING.
• If there are no channels with EDS signals or the
antenna signal is weak, the AUTO CLOCK
Setting may not operate. In this case, a “EDS CH
IS NOT AVAILABLE” message will display and
the mode will change to MANUAL CLOCK
Setting. Refer to page 26 to set the clock
manually.
24
AUTO CLOCK Setting
There are two methods of setting the clock: AUTO CLOCK and MANUAL CLOCK.
AUTO CLOCK uses EDS signals, which are provided by some TV stations, to
automatically adjust the clock. MANUAL CLOCK set the clock manually in areas
where no channel carries EDS signals.
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
“SET UP”, and press ENTER.
3
Press a/b to move the cursor to
“CLOCK”, and press ENTER.
4
Press a/b to move the cursor to
“AUTO CLOCK”, and press ENTER.
Note:
• The CLOCK can be stopped completely by
setting “CLOCK” to “OFF”.
SETTING THE CLOCK
CLOCK
AUTO CLOCK
M
ANUAL CLOCK
OFF
SELECT : ENTER: EXIT:
RETURN
ENTER
MENU
M
ENU
SLEEP T I
M
ER
V I DEO ADJUST
PRESET
CLOSED CAPT ION
V–CHIP BLOCK
SET UP
SELECT : ENTER: EXIT:
ENTER
MENU
BLUE SCREEN
[OFF]
LANGUAGE
SELECT : EXIT:
ENTER
RETURN
SET UP
CH–SETT ING
ENTER:
MENU
CLOCK
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
ENTER
MENU
Time reset for power outage or AC adapter disconnected
If the TV has a power outage or the AC adapter cord is disconnected, the time display will have to be reset. In that
case, refer to “AUTO CLOCK Setting” and “MANUAL CLOCK Setting” on pages 24 to 26.
a/b
ENGLISH
25
SETTING THE CLOCK (Continued)
ENTER/
a/b/c/d
MENU
AUTO CLOCK
EDS CH SET [AUTO ]
EXIT:
RETURN
EDS CH [ –––]
START
ENTER:
ENTER
ADJUST :
MENU
PLEASE
W
AIT
NO
W
SEARCH ING T IME
STOP:
2
STEREO
<
ON A I R
SAP
M
ONO
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
AUTO CLOCK Setting (Continued)
5
Press a/b to move the cursor to “EDS
CH SET”, and press ENTER.
6
Press c/d to select “AUTO” or
“MANUAL”.
7
Press a/b to move the cursor to
START, and press ENTER.
To cancel AUTO CLOCK
Press c.
| If you do not know the channel that carries
EDS signals in your area, select “EDS CH
SET” to “AUTO” and select START. If you
know the channel of the EDS signal carrier
in your area, select “EDS CH SET” to
“MANUAL”. Set the EDS CH and select
“START”.
| When set to “AUTO CLOCK”, the time is
acquired automatically when MAIN
POWER is turned OFF. (This function will
not work when EDS CH is not set.)
Note:
• CLOCK: The AUTO CLOCK setting may take
from several minutes to an hour depending on the
number of channels to receive and signal status.
• If there are no channels with EDS signals or the
antenna signal is weak, the AUTO CLOCK
Setting may not operate. In this case, an “EDS
CH IS NOT AVAILABLE” message will display,
and the MANUAL CLOCK Setting screen
appears. Refer to “MANUAL CLOCK Setting” on
page 26 to set the clock manually.
• If you know the Channel of the EDS signal carrier
in your area, set “EDS CH SET” to “MANUAL”
and select “START”. In case, the message “EDS
CH (XXX) EDS DATA IS NOT AVAILABLE”
displays, set “EDS CH SET” to “AUTO” when the
AUTO CLOCK Setting screen appears.
• If broadcasting channels are not memorized, EDS
signals cannot be received even when the “EDS
CH SET” is set to “AUTO”. In this case, try EZ
SETUP again. (See page 43.)
26
MANUAL CLOCK Setting
If there are no channels with EDS signals, set the clock manually using MANUAL
CLOCK.
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
“SET UP”, and press ENTER.
3
Press a/b to move the cursor to
“CLOCK”, and press ENTER.
4
Press a/b to move the cursor to
“MANUAL CLOCK”, and press ENTER.
5
Press a/b to move the cursor to
“TIME”, and press ENTER.
6
Press c/d to set the time, and press
ENTER.
12:00AM 11:59AM
11:59PM 12:00PM
Note:
• Make sure to press ENTER after adjusting
the time. Otherwise, the time will not be
set.
7
Press MENU to return to the main
screen.
SETTING THE CLOCK (Continued)
ENTER/
a/b/c/d
MENU
Daylight Saving-Time (DST) Adjustment
The Daylight Saving-Time changes as shown below. Set the “DST” to “ON” to forward the clock by 1 hour. To rewind
the clock by 1 hour, set the “DST” to “OFF”.
(Spring)
On the first Sunday in April D.S.T. starts.
(Autumn)
On the last Sunday in October D.S.T. finishes.
Advances 1 hour.
Rewinds 1 hour.
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
M
ENU
SLEEP T I
M
ER
PRESET
CLOSED CAPT ION
V–CHIP BLOCK
SET UP
SELECT : EXIT:
V I DEO ADJUST
ENTER:
ENTER
MENU
CLOCK
AUTO CLOCK
M
ANUAL CLOCK
OFF
SELECT : ENTER: EXIT:
RETURN
ENTER
MENU
M
ANUAL CLOCK
T IME [ 12: 0 0AM]
EXIT:
RETURN
DST [OFF ]
ENTER:
ENTER
ADJUST :
MENU
BLUE SCREEN
[OFF]
LANGUAGE
SELECT : EXIT:
ENTER
RETURN
SET UP
CH–SETT ING
ENTER:
MENU
CLOCK
1:00AM 2:00AM
3:00AM 4:00AM
1:00AM 2:00AM
1:00AM 2:00AM
ENGLISH
27
TV SIGNALS IN YOUR REGION
This product is factory set to comply with the TV broadcasting system in the United States.
The VIDEO INPUT mode is compatible with color systems worldwide and is automatically set.
Country
TV broadcasting
Factory setting of color system User setting
system
TV Video TV
U.S.A.
Color: NTSC NTSC (N358) World Multi
TV ch: US ch US ch Auto System
Not required or N/A
Canada
Color: NTSC NTSC (N358) World Multi
TV ch: US ch US ch Auto System
Not required or N/A
The World Multi Auto System is compatible with all color
systems indicated below.
1 N358
2 N443
3 PAL
4 PAL-M
5 PAL-N
6 SECAM
7 PAL-60
28
BATTERY CHARGE and TRANSMISSION SETTING
Battery Charge
The “BATTERY CHARGE” is set to “ON” when shipped from the factory. The
battery will deteriorate if it continues to be charged after having been fully charged.
It is recommended to set the “BATTERY CHARGE” to “OFF” when the battery
is not used frequently.
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
“PRESET”, and press ENTER.
3
Press a/b to move the cursor to
“BATTERY CHARGE”, and press
ENTER.
4
Press c/d to change the setting, and
press ENTER.
5
Press MENU to return to the main
screen.
Transmission Setting
When shipped from the factory, the “CHANNEL” of the “TRANSMISSION
SETTING” is set to “AUTO”, and the “DISTANCE” is set to “NEAR”. However,
when reception is poor due to the presence of an interference source in close
proximity, change the settings for “CHANNEL” or “DISTANCE” to ensure normal
reception.
ENTER/
a/b/c/d
MENU
[1] Preparing for “TRANSMISSION SETTING”
1
Connect the antenna to the Wireless
Center.
2
Install the Wireless Center and TV
receiver next to each other.
3
Turn on the power for both the Wireless
Center and TV receiver.
4
Press MENU to display the MENU
screen.
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
M
ENU
SLEEP T I
M
ER
V I DEO ADJUST
PRESET
CLOSED CAPT ION
V–CHIP BLOCK
SET UP
SELECT : ENTER: EXIT:
ENTER
MENU
AC cord
AC wall
outlet
AC adapter
Wireless
Center
Transmission
TV main unit
NOW ACCESSING.
BRIGHTNESS [ BRIGHT ]
M
TS
AUTO PO
W
ER OFF
RETURN
[STEREO]
[OFF ]
PICTURE FLIP
AV2 IN/OUT
BATTERY
CHARGE
[NOR
M
AL ]
[IN ]
PRESET
TRANSMISSION SETTING
SELECT : ENTER: EXIT:
ENTER
MENU
ENGLISH
29
Transmission Setting (Continued)
5
Press a/b to move the cursor to
“PRESET”, and press ENTER.
6
Press a/b to move the cursor to
“TRANSMISSION SETTING”, and press
ENTER.
[2] Setting Channel
Four settings can be selected for the communication channel consisting of
Auto, A, B and C. When set to “AUTO”, available channels that can be
transmitted are set automatically. It is recommended to normally set the
communication channel to “AUTO”.
AUTO A B C
1
Press a/b to select “CHANNEL”, and
then press ENTER.
2
Press c/d to select “AUTO”, and then
press ENTER.
• The available settings change in the
order shown below each time
c/d is pressed.
AUTO A B C
•“ADJUSTING CHANNEL SETTING.” is
displayed on the screen and the
communication channel is set
automatically.
M
ENU
SLEEP T I
M
ER
V I DEO ADJUST
PRESET
CLOSED CAPT ION
V–CHIP BLOCK
SET UP
SELECT : ENTER: EXIT:
ENTER
MENU
BRIGHTNESS [ BRIGHT ]
M
TS
AUTO PO
W
ER OFF
RETURN
[STEREO]
[OFF ]
PICTURE FLIP
AV2 IN/OUT
BATTERY
CHARGE
[NOR
M
AL ]
[IN ]
PRESET
TRANSMISSION SETTING
SELECT : ENTER: EXIT:
ENTER
MENU
STATUS:A
[ A]
DISTANCE
RETURN
[ FAR]
STATUS:NEAR
TRANSMISSION SETTING
CHANNEL
SELECT :
ENTER: EXIT:
ENTER
MENU
Displayed in yellow
BATTERY CHARGE and TRANSMISSION SETTING (Continued)
ADJUSTING CHANNEL SETTING.
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
ENTER/
a/b/c/d
MENU
[ AUTO ]
DISTANCE
RETURN
[ FAR]
STATUS:NEAR
TRANSMISSION SETTING
CHANNEL
SELECT :
ENTER: EXIT:
ENTER
MENU
30
Transmission Setting (Continued)
[3] Setting Distance
Select the Distance mode that gives the best reception and picture quality.
FAR
MID
NEAR
Setting
Picture
Quality
Data Error
Correction
NEAR
Best
Weak
Worst
Strong
MID
FAR
BATTERY CHARGE and TRANSMISSION SETTING (Continued)
STATUS: A
DISTANCE
RETURN
[ FAR ]
STATUS: NEAR
TRANSMISSION SETTING
CHANNEL
[ AUTO ]
SELECT :
ENTER: EXIT:
ENTER
MENU
Displayed in yellow
ADJUST I NG D I STANCE SETT I NG.
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
STATUS: A
DISTANCE
RETURN
[ NEAR]
TRANSMISSION SETTING
CHANNEL
[ AUTO ]
SELECT :
ENTER: EXIT:
ENTER
MENU
ENTER/
a/b/c/d
MENU
1
Press a/b to select “DISTANCE”, and
then press ENTER.
2
Press c/d to select the desired
distance, and then press ENTER.
• “ADJUSTING DISTANCE SETTING.” is
displayed on the screen and the
communication distance is set
automatically.
3
Press MENU to return to the main
screen.
Note:
• Automatic channel selection is only made
when the main unit is first switched on or
when the function is selected from the
menu.
• If reception has become poor after
changing the locations of the Wireless
Center and TV receiver, the problem may
be corrected by resetting the communica-
tion channel and communication distance.
NEAR: Enables finer picture quality.
MID: Enables normal picture quality and middle distance transmission.
FAR: Enables longer distance transmission. (Picture quality becomes
relatively poor.)
ENGLISH
31
BASIC OPERATION
Turning on POWER
1
Press MAIN POWER of the TV main
unit.
• “NOW ACCESSING.” is displayed on
the screen.
• The POWER indicator of the TV main
unit turns green.
Note:
• The On-screen indicator disappears after a
few seconds.
2
Press the MAIN POWER button of the
Wireless Center.
• The POWER indicator of the Wireless
Center turns green.
Standby
To turn off the LCD TV
Press POWER on the remote control.
• The POWER indicator turns red.
To turn the LCD TV back on
Press POWER again.
• The POWER indicator turns green.
Control section of main unit
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
POWER
▼ On-screen display
2
STEREO
SAP
M
ONO
POWER indicator
1
2
MAIN POWER
POWER indicator
32
BASIC OPERATION (Continued)
Switching TV/VIDEO [AV1/AV2//AV3/AV4] Modes
1
Turn on the power of the connected
video equipment.
2
Press TV/VIDEO and select the
applicable input source. The screen
displays AV1, AV2, AV3, AV4 or TV
mode each time TV/VIDEO is pressed.
Note:
• The AV input mode indication remains for
3 seconds.
• AV1: Video equipment connected to the AV-IN1
input terminals.
The S-video input terminal is additionally
provided for the AV-IN1 input. If both the S-
video terminal and normal video terminals
are connected with cables, the S-video
input terminal takes priority.
• AV2: AV2 mode is used to adjust the preset
settings and IN or OUT can be selected.
AV2 indication is not displayed when OUT
is selected. (For details on setting AV2 IN/
OUT, see page 39.)
• AV3: Video equipment connected to the AV-IN3
input terminals.
• AV4: The AV4 input terminal is in the TV main
unit. This terminal is for directly connecting
to an external device such as a game
device.
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
TV/VIDEO
AV2
AV3
12
AV1
AV4
STEREO
<
ON A IR
SAP
M
ONO
AV1 mode
AV2 mode
TV mode
AV3 mode
AV4 mode
ENGLISH
33
Sound Volume
1
Press VOL (+) to increase the sound
volume. The bar indicator shifts right.
2
Press VOL (–) to decrease the sound
volume. The bar indicator shifts left.
To mute the sound
1
Press MUTE to temporarily turn off the
sound.
The MUTE mark “
” is displayed FOR
4 SECONDS.
2
Press MUTE or VOL (+)/(–) to turn the
sound back to the previous level.
The mute function is automatically
turned off when any of the following
buttons are pressed: POWER, VOL (+)/
(–) or MTS.
To select MTS (Multichannel TV Sound)
1
Press MTS to display the MTS screen.
2
Press MTS to select the MTS settings.
STEREO: stereo audio
SAP: secondary audio program
MONO: monophonic audio
Note:
•“<ON AIR” appears when a STEREO or
SAP broadcast is being aired.
BASIC OPERATION (Continued)
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
MUTE
VOL
(+)/(–)
MTS
POWER
50
VOLUME
10
VOLUME
30
VOLUME
2
STEREO
<
ON A I R
SAP
M
ONO
34
Changing Channels
Changing channels by using Channel Select on the remote control
• This LCD TV set allows you to select up to 125 channels (1 to 125). To
select a channel, enter a 2- or 3-digit number.
To select a 1- or 2-digit channel
number (e.g., Channel 5):
Complete the following procedure within 4
seconds.
1
Press the button.
2
Press the
5
button.
Note:
• When selecting a 1-digit channel number,
do not fail to press the button first.
To select a 3-digit channel number
(e.g., Channel 115):
Complete the following procedure within 4
seconds.
1
Press the button.
2
Press the button.
3
Press the
5
button.
Note:
• The 3-digit channel number can be
selected only when the receiving mode is
set to “CABLE” in “CH-SETTING”. (For
details on setting the receiving mode, see
page 43.)
• Press FLASHBACK to show the previous
channel.
• Tuning operation may take a few seconds to
complete when using the remote control,
because of the wireless transmission speed.
This does not indicate a malfunction.
BASIC OPERATION (Continued)
Channel
Select
CH
(
)/( )
FLASH-
BACK
Changing channels with CH ( )/( ) on the remote control
Air Press CH ( ) and the channels change in the order shown below:
2 → 3 → . . . → 68 → 69 → 2 → 3 → . . .
Press CH (
) and the channels change in the order shown below:
3 → 2 → 69 → 68 → . . . → 3 → 2 → . . .
Cable Press CH (
) and the channels change in the order shown below:
1 → 2 → 3 → . . . → 125 →1 → 2 → 3 → . . .
Press CH
( ) and the channels change in the order shown below:
3 → 2 → 1 → 125 → . . . → 3 → 2 → 1 → . . .
CHVOL
POWER
ENTER
DISPLAY
MUTE
SLEEP PIC. FLIP
BRIGHT TV/VIDEO MENU
FLASH-
BACK
0–
5
1 ––
11–
115
ENGLISH
65
SPECIFICATIONS
Items
LCD panel 15" Advanced Super View & BLACK TFT LCD
Number of dots 921,600 dots VGA
Video color systems N358
Destination USA/Canada
TV Standard (CCIR) M/NTSC
TV function TV Tuning System PLL 181 ch.
STEREO MTS+SAP
CATV 125 ch.
Y/C FILTER 3-LINE COMB FILTER
Brightness 430 cd/m
2
Lamp life (Fluorescent lamp) 60,000 hours
Viewing angles H: 170° V: 170°
Audio amplifier 2.1 W × 2
Speakers 1
37
/
64
inch (4 cm), 2 pcs
AV-IN1 AV-IN1, S-VIDEO-IN
AV-IN2 AV-IN2/AV-OUT
Terminals
AV-IN3 AV-IN3
AV-IN4 (TV main unit) AV-IN4 (TV main unit)
Antenna F-Type
Headphone Mini-jack for stereo (ø3.5 mm)
OSD language English/French/Spanish
Power supply TV main unit: DC 15V, Wireless center: DC 12V
TV main unit
with stand : 13.89 lbs. (6.3 kg)
Weight without stand : 11.02 lbs. (5.0 kg)
Wireless Center 2.43 lbs. (1.1 kg)
Accessories Wireless remote control (×1), Remote control holder (×1), Batteries (×2), Battery (×1),
AC adapters (×2), Wireless center (×1), Wireless center stand (×1),
Cable clamps (×2), Table stand (×1), Video controller (×1), Operation manual (×1),
Antenna cables (×2), Connecting System Chart of LC-15L1U (×1), Registration Card (×1),
Caution Sheet (×1)
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improve-
ment without prior notice. The performance specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
Model
LC-15L1U
… 66 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sharp LC-15L1U-S Operation Manual bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sharp LC-15L1U-S Operation Manual in de taal/talen: Engels als bijlage per email.

De handleiding is 2,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info