19045
68
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
2
HT-X1
Important Instruction
SPECIAL NOTES
Note to CATV system installer:
This reminder is provided to call the CATV system installer's atten-
tion to Article 820-40 of the National Electrical Code that provides
guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s en-
closure that may be of sufficient magnitude
to constitute a risk of electric shock to per-
sons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main-
tenance (servicing) instructions in the lit-
erature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
0501
THIS PRODUCT IS A CLASS 1 LASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
AS THE LASER BEAM USED IN THIS PRODUCT IS HARMFUL TO
THE EYES, DO NOT ATTEMPT TO DISASSEMBLE THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
CAUTION:
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful in-
terference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to ra-
dio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
0402
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the subwoofer/amplifier unit.
Please retain this information.
Model number .......................................................
Serial number .......................................................
Date of purchase .......................................................
Place of purchase .......................................................
0501
8
HT-X1
General Information
Precautions
"
General
! Please ensure that the equipment is positioned in a well-venti-
lated area and that there is at least 4" (10 cm) of free space along
the sides and back. There must also be a minimum of 6" (15 cm)
of free space on the top of the unit.
! Do not place anything on top of the components.
! Do not expose the system to moisture, to temperatures higher
than 140°F (60°C) or to extremely low temperatures.
! If your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and
then turn on your system.
! This system should only be used within the range of 41°F - 95°F
(5°C - 35°C).
Warning:
The voltage used must be the same as that specified by this sys-
tem. Using this product with a higher voltage other than that speci-
fied is dangerous and may result in a fire or other types of accident,
causing damage. SHARP will not be held responsible for any dam-
age resulting from the use of this system with a voltage other than
that specified.
" Volume control
The sound level at a given volume setting depends on speaker effi-
ciency, location and various other factors. It is advisable to avoid
exposure to high volume levels, which occurs while turning the unit
on with the volume control setting up high, or while continually lis-
tening at high volumes.
! Use the system on a firm, level surface free
from vibration.
!
Keep the system away from direct sun-
light, strong magnetic fields, excessive
dust, humidity and electronic/electrical
equipment (home computers, facsimiles,
etc.) which generates electrical noise.
Subwoofer/amplifier unit
Main unit
4" (10 cm) 4" (10 cm)
4" (10 cm) 4" (10 cm)
4" (10 cm) 4" (10 cm)
4" (10 cm)
6" (15 cm)
6" (15 cm)
6" (15 cm)
4" (10 cm)
4" (10 cm)
! In case of an electrical storm, unplug the
subwoofer/amplifier unit for safety.
! Hold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
! Do not remove the outer cover, as this
may result in electric shock. Refer inter-
nal service to your local SHARP service
facility.
9
HT-X1
General Information
Description of discs
"
Types of playable discs
The unit can play back discs bearing any of the following marks:
Some DVD may not function as described in the manual. See
the disc jacket for restrictions.
! For unplayable discs, see page 11.
DVD
DVD-Video Disc DVD-R DVD-RW DVD+R DVD+RW
for NTSC system for NTSC
system
for NTSC
system
for NTSC
system
for NTSC
system
Recorded in the vid-
eo mode (*1) (*2)
Recorded in the vid-
eo mode (*1)
(*1) Some discs may not play properly due to the status of the
equipment used for recording, characteristics of the discs,
scratches, dirt, or dirty optical pickup lens.
(*2) DVD-RW discs recorded in VR mode (Video Recording format)
cannot be played back.
CD
Audio CD Audio CD-R Audio CD-RW
Or CDV (*1) CD-R/RW recorded in MP3/WMA/JPEG
format (*2)
(*1) Only the audio on the CDV can be played.
(*2) Some discs may not play properly due to the status of the
equipment used for recording, characteristics of the discs,
scratches, dirt, or dirty optical pickup lens.
4.7
Icons used in this operation manual
Some functions may not be available depending on discs. The fol-
lowing icons indicate the discs that can be used in the section.
... Indicates DVDs for NTSC system.
... Indicates audio CDs.
... Indicates CD-R/RW with MP3 recording.
... Indicates CD-R/RW with WMA recording.
... Indicates CD-R/RW with JPEG recording.
! Some operations may not be performed depending on discs
even if they are described in this manual.
! During operation, " " may be displayed on the screen. This
means that the operations described in this manual are prohibit-
ed by the disc.
10
HT-X1
General Information
Description of discs (continued)
"
DVD-Video
A popular type of DVD disc of the same size as a CD, mainly con-
taining video images.
Region number
Title and chapter
DVD-Video discs are divided into "titles" and "chapters". If the disc
has more than one movie on it, each movie is a separate "title".
"Chapters" are subdivisions of titles.
" DVD-R/DVD-RW/DVD+R/DVD+RW
! You can play DVD-R/DVD-RW/DVD+R/DVD+RW discs recorded
in the video mode.
! Before playing DVD-R/DVD-RW/DVD+R/DVD+RW discs with
this unit, finalize them with the equipment used for record-
ing.
"
Audio CD
Track
The audio CD is composed of "tracks". Tracks are equivalent to
songs on a CD.
" MP3/WMA/JPEG format on CD-R/CD-RW
An MP3 file is audio data compressed in the MPEG 1 audio layer 3
format. MP3 files have the extension ".mp3". (Files with the exten-
sion ".mp3" may not play, or noise may occur during playback if not
recorded in the MP3 format.)
WMA is an audio file format developed by Microsoft with the ".wma"
extension. This type of audio file is recorded through Microsoft Win-
dows operating system.
A JPEG file is still image data compressed in the JPEG (Joint Pho-
tographic Experts Group) format. JPEG files have the extension
".jpg".
Folder and file
MP3/WMA/JPEG discs consist of "folders" and "files".
DVD discs are programmed with region
numbers indicating countries in which
they can be played. This system can
play discs with region number "1" or
"ALL".
Region number
(playable area number)
1
ALL
Chapter 1
Title 1 Title 2
Chapter 2 Chapter 3 Chapter 1 Chapter 2
Track 1 Track 2 Track 3 Track 4
MP3
disc
WMA
disc
JPEG
disc
File 1
Folder 1
File 2 File 1
Folder 2
File 2
19
HT-X1
Preparation for Use
System connections
!
Make sure to disconnect the AC power cord from the wall outlet before you connect/disconnect cables to/from jacks inside the
back cover of the main unit or jacks of the subwoofer/amplifier unit.
! After connecting cables, attach the back cover and operate the main unit.
Subwoofer/
amplifier unit
Antenna connection
(see page 20)
Connecting
the AC
power cord
(see page 25)
TV connection
(see pages 22, 23)
Speaker connection (see page 21)
Surround speaker
(left)
Surround speaker
(right)
Front speaker
(left)
Center
speaker
Front speaker
(right)
White
Red
Green
Blue
Gray
White
GrayBlue
Green
Red
Main unit
Connecting the system
connection cable
(see page 20)
AM loop antenna
FM antenna
HT-X1 (U) TINSEA050SJZZ
20
HT-X1
Preparation for Use
System connections (continued)
" Connecting the system connection cable
Connect the main unit and subwoofer/amplifier unit as follows.
" Antenna connection
Note:
Placing the antenna on the system or near the AC power cord may
cause noise pickup. Place the antenna away from the system for
better reception.
Installing the AM loop antenna:
Outdoor FM or AM antenna:
Use an outdoor FM or AM antenna if you require better reception.
Consult your dealer.
When using an outdoor AM antenna, be sure to keep the wire of the
AM loop antenna connected.
Subwoofer/
amplifier unit
1
2
Main unit
1
2
Black
Blue
Blue Black
Antenna terminals
Supplied FM antenna:
Connect the FM antenna wire to the FM
75 OHMS jack and position the FM an-
tenna wire in the direction where the
strongest signal can be received.
Supplied AM loop antenna:
Connect the AM loop antenna wire to the
AM and GND terminals. Position the AM
loop antenna for optimum reception.
Place the AM loop antenna on a shelf,
etc., or attach it to a stand or a wall with
screws (not supplied).
< Assembling > < Attaching to the wall >
Wall Screws (not supplied)
FM
antenna
AM loop
antenna
AM loop
antenna
Outdoor AM antenna
49 feet (15 m)
25 feet
(7.5 m )
Outdoor
FM antenna
Ground wire
Ground rod
25
HT-X1
Preparation for Use
" Connecting the AC power cord
After checking all the connections have been made correctly, plug
the AC power cord to the AC power input jack of the subwoofer/
amplifier unit, and then to the AC outlet.
Notes:
! Never use a power cord other than the one supplied. Otherwise,
a malfunction or an accident may occur.
! Unplug the AC power cord from the wall outlet if the subwoofer/
amplifier unit will not be in use for a prolonged period of time.
" To turn the power on
Press the ON/STAND-BY button.
If the power does not turn on, check if the AC power cord and sys-
tem connection cable are plugged in properly.
To set the system to stand-by mode:
Press the ON/STAND-BY button again.
Note:
After the system enters the power stand-by mode, wait a few sec-
onds to turn on again.
Cooling fan:
A cooling fan is built into this subwoofer/amplifier unit for better heat
radiation. Do not cover the opening in this section with any obsta-
cles to avoid damage to the subwoofer/amplifier unit.
AC outlet
(AC 120 V, 60 Hz)
Subwoofer/
amplifier unit
Cooling fan
Subwoofer/
amplifier unit
Main unit
26
HT-X1
Preparation for Use
Remote control
" Battery installation
Precautions for battery use:
!
Replace all old batteries with new ones at the same time.
!
Do not mix old and new batteries.
!
Remove the batteries if the system will not be used for long peri-
ods of time. This will prevent potential damage due to battery
leakage.
Caution:
!
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
!
Installing the batteries incorrectly may cause the system to mal-
function.
Battery removal:
Remove the battery cover. Push each battery toward the battery
terminal and take them out.
Notes concerning use:
! Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
! Periodically clean the transmitter on the remote control and the
sensor on the main unit with a soft cloth.
! Exposing the sensor on the main unit to strong light may interfere
with operation. Change the lighting or the direction of the main
unit if this occurs.
! Keep the remote control away from moisture, heat, shock, and
vibrations.
" Test of the remote control
Check the remote control after checking all the connections (see
pages 19 - 25).
Point the remote control directly at the remote sensor on the main
unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now,
you can enjoy music.
! The main unit is equipped with 2 remote sensors. Use them
according to the installation method as shown below.
Use 2 "AAA" size batteries (UM-4, R03, HP-16 or similar).
Batteries are not included.
1 Remove the battery cover.
2 Insert the batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them toward the
battery terminals.
3 Replace the cover.
8"-20'
(0.2 m - 6 m)
Remote sensor
Main unit
27
HT-X1
Preparation for Use
General control
" Volume control
" Muting
" To change the display brightness (2 levels)
Hold the DISPLAY/(-DIMMER) button down for 3 seconds or more.
Each time you press, brightness changes.
Main unit operation:
When the VOLUME control is turned
clockwise, the volume will increase.
When it is turned counterclockwise,
the volume will decrease.
Remote control operation:
Press the VOL (+ or -) button to in-
crease or decrease the volume.
The volume is muted temporarily
when pressing the MUTE button.
! Press again to restore the vol-
ume.
!
The mute status is canceled
when you adjust the volume.
(*) After approx. 5 seconds of DVD playback, the display dims and
the original brightness returns when you stop playback. The
brightness remains unchanged during playback of other media.
0 1 10
......
39 40
Dimmed
(*)
Brightened
HT-X1 (U) TINSEA050SJZZ
28
HT-X1
DVD Operation
Playing a disc
Turn on the TV, and switch the input to the "VIDEO 1" or "VIDEO 2",
etc. accordingly.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the button to set the in-
put to "DVD".
3
Insert a disc into the disc insertion slot with the label side
toward you.
! The disc enters automatically.
Notes:
! Do not push in the disc. Damage may result.
! Load an 3" (8 cm) disc gently in the middle of the insertion
slot (do not use an adaptor.)
Some discs play automatically.
DVD
CD
No Disc
Audio Visual
Entertainment
Disc insertion slot
Label side
Disc insertion slot
Label side
29
HT-X1
DVD Operation
To stop playback:
DVD:
Press the button twice.
CD/MP3/WMA/JPEG:
Press the button.
To remove the disc:
4
If playback does not start, press the (DVD/CD ) button.
When the menu appears on the TV screen:
On DVD, select an item by using the cursor ( , , or ) button
and press the ENTER button.
To interrupt playback:
Press the STILL button on the remote con-
trol.
To resume playback from the same point, press
the DVD/CD button.
Chapter or track number
The sound mode in use appears during DVD playback.
Play indicator
Playing time
Caution when inserting disc:
! Do not touch the playback side.
! Do not insert two or more discs in the disc insertion slot.
! Discs with labels, stickers or glue attached
may cause damage to the main unit.
! Do not use discs of special shapes (heart, oc-
tagon, etc.) or 3" (8 cm) discs with an adaptor.
Malfunction may result.
! A disc with scratches or fingerprints may not play properly. Re-
fer to "Care of discs (page 65)" and clean the disc.
! Insert or remove the disc straight. Otherwise,
damage may result.
1. In the stop mode, press the button.
2. Remove the disc.
Disc
34
HT-X1
DVD Operation
Useful operation (continued)
" To change the audio language (audio output)
During playback, you can change the audio language (audio out-
put).
Notes:
!
The audio language on some DVDs may not be changed.
!
For audio language and audio system, refer to the manual of the
disc.
!
When you set the unit to the stand-by mode or replace the disc,
settings return to the default.
" To brighten an image
To restore the original brightness:
In step 1, select "OFF".
1
While a disc is playing, press
the SHIFT button and then the
AUDIO button.
Audio language information
2
Repeat step 1 to select the desired audio number.
When playing DVD, the language changes as follows:
When playing audio CD and MP3, the sound changes as fol-
lows:
Audio 1/3: AC-3 5.1 English
1: Original <English>
(Dolby Digital 5.1
ch
Surround)
2: English
(Dolby Digital 2 ch Surround)
Audio 1/3: AC-3 5.1 English
Audio 2/3: AC-3 2CH English
Mono Left
Mono Right
Stereo
1
During playback, press the
SHIFT button and then the GAM-
MA button to select "ON".
"ON" and "OFF" will be switched by each press of these but-
tons.
2
Within 10 seconds, press the
cursor ( or ) button to set the
level.
Level Setting Level Setting
OFF Normal image ON Brighter
ON Slightly brighter ON A lot brighter
OFF
G
ON
G
35
HT-X1
DVD Operation
" To improve the image quality
To restore the original image quality:
In step 1, select "OFF".
1
During playback, press the
SHIFT button and then the
S.PICTURE button to select
"ON".
"ON" and "OFF" will be switched by each press of these but-
tons.
2
Within 10 seconds, press the
cursor ( or ) button to set the
level.
Level Setting Level Setting
OFF Normal ON Clearer
ON Slightly clearer ON A lot clearer
OFF
S
ON
S
36
HT-X1
DVD Operation
Useful operation (continued)
" To select a title from the top menu of the disc
On a DVD with multiple titles, you can select a title from the top menu.
Note:
The procedure shown here provides only general steps. The actual
procedure for using the disc menu depends on the disc you are
using. See the disc jacket for details.
" To select a subtitle or audio language from the
disc menu
You can select the desired subtitle/audio language and sound sys-
tem (5.1 ch Dolby Digital or DTS sound) on your DVD if it has a disc
menu.
Note:
The procedure shown here provides only general steps. The actual
procedure for using the disc menu depends on the disc you are
using. See the disc jacket for details.
" Still picture/Frame advance
You can freeze the image and advance frame by frame.
Note:
Still picture and frame advance features are disabled on some
discs.
" Slow-motion play
You can slow down the playback speed.
Note:
On some discs, slow-motion play functions are disabled.
1
In the stop mode or during play-
back, press the SHIFT button
and then the TOP MENU/MENU
button.
Example
2
Press the cursor ( , , or ) button to change the setting
and press the ENTER button.
! The selected title is played.
!
You can also use the direct number buttons for some discs.
1
In the stop mode or during play-
back, press the TOP MENU/
MENU button.
Example
2
Press the cursor ( , , or ) button to change the setting
and press the ENTER button.
You can also use the direct number buttons for some discs.
21 Drama Action
43SF
Comedy
1. Highlights
2. Start Movie
1
While a disc is playing, press
the STILL button.
2
Each press of the STILL button advances the frame in
the still mode.
3
Press the (DVD/CD ) button to return to the normal
playback.
1
While a disc is playing, press
the STILL button.
2
Hold down the or button
for 2 seconds or more.
3
Press the (DVD/CD ) button to return to the normal
playback.
Pause
Pause
Slow Forward
Slow ForwardSlow Backward /
37
HT-X1
DVD Operation
" To change the angle
You can change the angle of view when playing a DVD video disc
that contains scenes recorded from multiple angles.
Notes:
! Some DVDs prohibit changing the angle.
! The angle number is not displayed if there is no other angle
recorded. " " is displayed instead.
! Refer to the manual of the disc as the operation may vary
depending on the disc.
" To zoom in on an image (zoom)
You can magnify images during playback.
To return to normal view:
Press the SHIFT button and then the ZOOM button. Repeat this to
select "Zoom off".
When you cancel the zoom function, you cannot shift the view.
Notes:
!
An image may become distorted when zoomed.
! Subtitles cannot be zoomed.
! The position of the current part is indicated in the lower left of the
screen.
1
When " " appears on the TV during playback, press the
SHIFT button and then the ANGLE button.
TV screen Unit display
2
Repeat step 1 to select the desired angle number.
1
1
While a disc is playing, press the SHIFT
button and then the ZOOM button.
2
Repeat step 1 to select the desired zoom setting.
3
To shift the view and display the desired part of a zoomed
image, press the cursor ( , , or ) button repeatedly.
Zoom x 1.5
Zoom x 1.5 Zoom x 2 Zoom x 3 Zoom off
40
HT-X1
DVD Operation
Useful operation (continued)
" To play the contents between the specified
points repeatedly (A-B repeat)
You can play the desired portion repeatedly by specifying it during
playback.
Notes:
!
A-B repeat play is disabled on some discs.
!
Some scenes in DVD may not allow A-B repeat play.
!
A-B repeat play for DVD is possible only within a title.
!
A-B repeat play for audio CD is possible only within a track.
!
When you press the button, the current A-B repeat play is can-
celed. (For DVD, press the button twice.)
" To change the display on the main unit
Notes:
! Title/chapter numbers or elapsed time may not appear depend-
ing on the disc.
! The playing time of the disc specified on the jacket, etc. may not
include silence between tracks, and may differ from that dis-
played on the main unit.
! Elapsed time on the display does not indicate the actual time.
1
While a disc is playing, press the SHIFT button and then
the A B REPEAT/ button.
TV screen Unit display
This registers the start point (A).
2
Press the SHIFT button and then the A B REPEAT/ but-
ton again to enter the end point (B).
A-B repeat plays from the start point (A) to the end point (B).
3
Press the SHIFT button and then the A B REPEAT/ but-
ton to return to the normal playback.
A-B Set A
A-B Repeat on
During playback, press the DISPLAY/(-DIMMER) button.
Each time you press the button, the display changes as follows:
DVD:
Title elapsed time
Title/Chapter number
Chapter elapsed time
CD:
Track elapsed time Total elapsed time
41
HT-X1
DVD Operation
" To change the display on TV screen
You can display or hide the operation indicators on the TV screen.
While the disc is playing, press the ON SCREEN button. (The
display is changed at each press of this button.)
When playing DVD, the display changes as follows:
When playing an audio CD, the display changes as follows:
Title playing time
Total number of chapters
Current chapter number
Total number of titles
Current title number
Disc type
Chapter playing time
Remaining playing time of
the current title
Remaining playing time of
the current chapter
Angle information
Repeat mode information
Audio language information
Subtitle information
1 / 8 2 / 10 00:38:58
1 / 8 2 / 10 -01:09:50
1 / 8 2 / 10 00:07:43
1 / 8 2 / 10 -00:02:38
DEF 1/9 DEF 1/3 1 / 3
1 / 19 -03:14
L
R
1 / 19 20:00
L
R
1 / 19 -40:37
L
R
1 / 19 01:02
L
R
Track playing time
Repeat mode information
Audio information
Remaining track playing time
Elapsed total playing time
Remaining total playing time
42
HT-X1
Audio CD Operation
Playing an audio CD
The following playback functions are the same as DVD operations.
Page
Playing a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 - 30
To locate the beginning of a chapter/track (skip) . . . . . . . . . . 31
Fast forward/Fast reverse (search) . . . . . . . . . . . . . . . . . . . . . 31
To change the audio language (audio output) . . . . . . . . . . . . 34
To play in the desired order (programmed playback) . . . . . . 38
To play repeatedly (repeat play) . . . . . . . . . . . . . . . . . . . . . . . . 39
To play the contents between the specified points repeatedly
(A-B repeat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
To change the display on the main unit . . . . . . . . . . . . . . . . . . 40
To change the display on TV screen . . . . . . . . . . . . . . . . . . . . 41
" To play in random order (random play)
The tracks on the disc can be played in random order automatically.
To cancel random play:
Press the button.
Notes:
!
On some discs, this function cannot be used.
!
You cannot set the random play while in the playback or pause
mode.
!
Random play is not allowed during programmed playback.
!
In random play, the unit will select and play tracks automatically.
(You cannot select the order of the tracks.)
!
Repeat play is not possible during random play.
In the stop mode, press the SHIFT button and then the RAN-
DOM/PROGRAM button.
All tracks play in random order.
TV screen Unit display
RandomPlay
CD:
MP3/WMA/JPEG:
Random
43
HT-X1
Audio CD Operation
" To start playback from the desired point (direct
play)
To select and play the desired track:
Note:
Direct play feature is disabled on some discs.
To play by specifying time (time search):
You can play tracks from the desired time point during playback.
Note:
Time search feature is disabled on some discs.
While in the stop or playback mode, press the direct number
buttons to select the track number.
TV screen Unit display
If the track number is 2 digits or more, press "+ 10" and enter the
number.
Example:
To select track 14, press "+10" and "4".
To select track 24, press "+10", "+10" and "4".
To select track 112, press "+10" eleven times and press "2".
Select: 14
1
While the disc is playing, press the DIRECT button.
Time
2
Specify the time with the direct number buttons.
! Enter minutes and seconds.
!
To specify 1 hour 13 minutes and 40 seconds, enter "7340".
!
If you enter the wrong number, start over from step 1.
3
Within 10 seconds, press the ENTER button.
1 / 19 MAX [04:56]
--:--
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
9906
Printed in China
TINSEA050SJZZ
05B N HK 1
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
9906
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original con-
tainer, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has
been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in
design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any
warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the
purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
(Be sure to have this information available when you need service for your Product.)
Warranty Period for this Product: One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from Warranty Coverage (if any): Non-functional accessories, supplies, and consumable items.
Where to Obtain Service: At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service: Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and
packaged securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
0311
HT-X1 Home Theater with DVD
68

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sharp HTX1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sharp HTX1 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info