Handleiding Sharp EL531V (pagina 1 van 1) (Engels)

17332

Verklein

Vergroot

Pagina terug

1/1

Pagina verder

EL-509V(H)/531V(H) (K0424T)_ENGLISH_1

INTRODUCTION

About operation examples, please refer to the attached sheet.

Refer to the number on the right of each title for use.

After reading this manual, store it in a convenient location for

future reference.

Note: Some of the models described in this manual may not

be available in some countries.

Operational Notes

To ensure trouble-free operation, please observe the follow-

ing points:

1. Do not carry the calculator in the back pocket of slacks or

trousers.

2. Do not subject the calculator to extreme temperatures.

3. Do not drop it or apply excessive force.

4. Clean only with a soft, dry cloth.

5. Do not use or store the calculator where fluids can splash

onto it.

♦ Press the RESET switch only in the following cases:

• When using for the first time

• After replacing the batteries

• To clear all memory contents

• When an abnormal condition occurs and all keys are

inoperative.

If service should be required on this calculator, use only a

SHARP servicing dealer, SHARP approved service facility, or

SHARP repair service where available.

Hard Case

EL-509V EL-509VH

EL-531V EL-531VH

SCIENTIFIC

CALCULATOR

OPERATION MANUAL

MODEL

DEG (°)

RAD (g) RAD

↔

DISPLAY

Symbol

Mantissa

Exponent

(During actual use not all symbols are displayed at the same

time.)

If the value of mantissa does not fit within the range

±0.000000001 – ±9999999999, the display changes to scien-

tific notation. The display mode can be changed according to

the purpose of the calculation.

: Appears when the entire equation cannot be dis-

played. Press </> to see the remaining (hid-

den) section.

2ndF : Appears when @ is pressed, indicating that the

functions shown in orange are enabled.

HYP : Indicates that h has been pressed and the hy-

perbolic functions are enabled. If @ H are

pressed, the symbols “2ndF HYP” appear, indicat-

ing that inverse hyperbolic functions are enabled.

ALPHA: Indicates that @ K or O (R) has been

pressed, and entry (recall) of memory contents and

recall of statistics can be performed.

FIX/SCI/ENG: Indicates the notation used to display a value

and changes each time @ f are pressed.

DEG/RAD/GRAD: Indicates angular units and changes each

time G is pressed.

STAT

: Appears when statistics mode is selected.

M:Indicates that a numerical value is stored in the

independent memory.

Equation

Display

BEFORE USING THE CALCULATOR

Key Notation Used in this Manual

In this manual, key operations are described as follows:

x To specify e

: @e

ln To specify ln : I

To specify x : @KX

Functions that are printed in orange above the key require

@ to be pressed first before the key. When you specify the

memory, press @K first. Numbers are not shown as

keys, but as ordinary numbers.

Power On and Off

Press ª to turn the calculator on, and @F to turn it off.

Clearing Methods

There are three clearing methods as follows:

Clearing Entry M*

A-D, X,Y*

operation (Display) STAT, ANS

ª ××

@c ×

RESET

: Clear × : Retain

Independent memory M.

Temporary memories A-D, X and Y, statistical data, and

last answer memory.

Editing the Equation

• Press < or > to move the cursor. You can also

return to the equation after getting an answer by pressing

> (<). See below for Multi-line playback function.

• If you need to delete a number, move the cursor to the

number you wish to delete then press d.

The number under the cursor will be deleted.

• If you need to insert a number, move the cursor to the place

immediately after where you wish to insert the number then

enter the number.

Multi-line Playback function (1)

This calculator is equipped with a function to recall previous

equations. Equations also include calculation ending instruc-

tions such as “=” and a maximum of 142 characters can be

stored in memory. When the memory is full, stored equations

are deleted in the order of the oldest first. Pressing [ will

display the previous equation and the answer. Further press-

ing [ will display preceding equations (after returning to

the previous equation, press ] to view equations in or-

der). In addition, @[ can be used to jump to the oldest

equation.

Press G

(Radians)

SCIENTIFIC CALCULATIONS

• Press @ m 0 to select the normal mode.

• In each example, press ª to clear the display. And if the

FIX, SCI, or ENG indicator is displayed, clear the indicator

by pressing @ f.

Arithmetic Operations (2)

• The closing parenthesis ) just before = or ;

may be omitted.

Constant Calculations (3)

• In the constant calculations, the addend becomes a con-

stant. Subtraction and division are performed in the same

manner. For multiplication, the multiplicand becomes a con-

stant.

• When performing calculations using constants, constants

will be displayed as K.

Functions (4)

• Refer to the operation examples of each function.

• Before starting calculations, specify the angular unit.

• The results of inverse trigonometric functions are displayed

within the following range:

Coordinate Conversions (10)

• Before performing a calculation, select the angular unit.

Rectangular coord. Polar coord.

• The calculation result is automatically stored in memories X

and Y.

Value of r or x: X memory

Value of θ or y: Y memory

Modify Function (11)

In this calculator, all calculation results are internally obtained

in scientific notation with up to 12 digits for the mantissa.

However, since calculation results are displayed in the form

designated by the display notation and the number of decimal

places indicated, the internal calculation result may differ from

that shown in the display. By using the modify function, the

internal value is converted to match that of the display, so that

the displayed value can be used without change in subse-

quent operations.

STATISTICAL CALCULATIONS

Press @ m 1 to select single-variable statistics

mode and @ m 2 to select two- variable statistics

mode. The following statistics can be obtained for each statis-

tical calculation (refer to the table below):

Single-variable statistical calculation (12)

Statistics of

Linear regression calculation (13)

Statistics of and and, in addition, estimate of y for a

given x (estimate y’) and estimate of x for a given y (esti-

mate x’)

x Mean of samples (x data)

sx Sample standard deviation (x data)

x Population standard deviation (x data)

n Number of samples

x Sum of samples (x data)

Sum of squares of samples (x data)

y Means of samples (y data)

sy Sample standard deviation (y data)

y Population standard deviation (y data)

y Sum of samples (y data)

Sum of squares of samples (y data)

xy Sum of products of samples (x, y)

r Correlation coefficient

a Coefficient of regression equation (y=a+bx)

b Coefficient of regression equation (y=a+bx)

Entered data are kept in memory until @ c or @

m 1 (2) are pressed. Before entering new data,

clear the memory contents.

[Data Entry]

Single-variable data

Data

frequency

k (To enter multiples of the

same data)

Two-variable data

Data

x &

Data

y k

Data

x &

Data

y &

frequency

k (To enter

multiples of the same data x and y.)

[Data Correction]

Correction prior to pressing k:

Delete incorrect data with ª.

Correction after pressing k:

Press > to confirm the latest entry and press @

J to delete it.

Statistical Calculation Formulas (14)

Refer also to the operation examples sheet.

In the statistical calculation formulas, an error will occur when:

• the absolute value of the intermediate result or calculation

result is equal to or greater than 1 × 10

100

• the denominator is zero.

• an attempt is made to take the square root of a negative

number.

ERROR AND CALCULATION RANGES

Errors

An error will occur if an operation exceeds the calculation

ranges, or if a mathematically illegal operation is attempted.

When an error occurs, pressing < (or >) automatically

moves the cursor back to the place in the equation where the

error occurred. Edit the equation or press ª to clear the

equation.

Error Codes and Error Types

Syntax error (Error 1):

• An attempt was made to perform an invalid operation.

Ex. 2 @{

Calculation error (Error 2):

• The absolute value of an intermediate or final calculation result

equals or exceeds 10

100

• An attempt was made to divide by 0.

• The calculation ranges were exceeded while performing calcu-

lations.

Depth error (Error 3):

• The available number of buffers was exceeded. (There are 8

buffers* for numeric values and 16 buffers for calculation in-

structions). *4 buffers in STAT mode.

Equation too long (Error 4):

• The equation exceeded its maximum input buffer (142 charac-

ters). An equation must be shorter than 142 characters.

Calculation Ranges (15)

Refer also to the operation examples sheet.

• Within the ranges specified, this calculator is accurate to ±1

in the least significant digit of the mantissa. When perform-

ing continuous calculations (including chain calculations),

errors accumulate leading to reduced accuracy.

Time, Decimal and Sexagesimal Calculations (9)

Conversion between decimal and sexagesimal numbers can

be performed. In addition, the four basic arithmetic operations

and memory calculations can be carried out using the

sexagesimal system.

Random Numbers

A pseudo-random number with three significant digits can be

generated by pressing @ ` =. To generate the

next random number, press =. You can perform this func-

tion in the normal and statistics modes.

• Random numbers use memory Y. Each random number is

generated on the basis of the value stored in memory Y

(pseudo-random number series).

Angular Unit Conversions (5)

Each time @ g are pressed, the angular unit changes

in sequence.

Memory Calculations (6)

This calculator has 6 temporary memories (A-D, X and Y),

one independent memory (M) and one last answer memory.

Independent memory and temporary memories are only avail-

able in the normal mode.

[Temporary memories (A-D, X and Y)]

A stored value can be recalled as a value or variable for the

use in equations.

• In case you store an infinite decimal in the memory, recall it

as a variable to obtain accurate answers.

Ex.) 1 / 3 O Y (0.3333...is stored to Y)

3 * R Y =

0.999999999

3 * @ K Y =

[Independent memory (M)]

In addition to all the features of temporary memories, a value

can be added to or subtracted from an existing memory value.

[Last answer memory (ANS)]

The calculation result obtained by pressing = or any other

calculation ending instruction is automatically stored in the

last answer memory.

Note:

Calculation results from the functions indicated below are

automatically stored in memories X or Y. For this reason,

when using these functions, be careful with the use of memo-

ries X and Y.

• Random numbers .................. Y memory

• →rθ, →xy ............................... X memory, Y memory

Temporary memories and last answer memory are cleared

even when the same mode is reselected.

θ = sin

–1

θ = tan

–1

x θ = cos

–1

DEG –90 ≤ θ ≤ 90 0 ≤ θ ≤ 180

RAD –

—

≤ θ ≤

—

0 ≤ θ ≤ π

GRAD –100 ≤ θ ≤ 100 0 ≤ θ ≤ 200

PRINTED IN CHINA / IMPRIMÉ EN CHINE

00KUP (TINSK0424THZZ)

• The multi-line memory is cleared by the following opera-

tions: @c, @F (including the Automatic

Power Off feature), mode change, RESET, @`,

@?, constant calculation, angle conversion/change,

coordinate conversion, numerical value storage to the tem-

porary memories and independent memory, and input/dele-

tion of statistical data.

Priority Levels in Calculation

This calculator performs operations according to the following

priority:

Functions preceded by their argument (x

-1

, x

, n!, etc.)

¿ Implied multiplication of a memory value (2Y, etc.)

Functions followed by their argument (sin, cos, etc.)

Implied multiplication of a function (2sin30, etc.)

nCr, nPr

×, ÷ +, – =, M+, M–, ⇒M, |DEG, |RAD, |GRAD,

DATA, CD, →rθ, →xy and other calculation ending instruction

• If parentheses are used, parenthesized calculations have

precedence over any other calculations.

INITIAL SETUP

Mode Selection

Normal mode (NORMAL): @m0

Used to perform arithmetic operations and function calcula-

tions.

Single-variable statistics mode (STAT x): @m1

Used to perform 1-variable statistical calculations.

Two-variable statistic mode (STAT xy): @m2

Used to perform 2-variable statistical calculations.

When executing mode selection, temporary memories, statis-

tical data and last answer memory will be cleared even when

reselecting the same mode.

Selecting the Display Notation and Decimal Places

The calculator has four display notation systems for display-

ing calculation results. When FIX, SCI, or ENG symbol is

displayed, the number of decimal places can be set to any

value between 0 and 9. Displayed values will be reduced to

the corresponding number of digits.

100000÷3=

[Floating point] ª100000/3= 33333.33333

→[Fixed decimal point] @f 33333.33333

[TAB set to 2] @i 2 33333.33

→[SCIentific notation] @f 3.33×10

→[ENGineering notation] @f 33.33×10

→[Floating point] @f 33333.33333

• If the value for floating point system does not fit in the

following range, the calculator will display the result using

scientific notation system:

0.000000001 ≤ | x | ≤ 9999999999

Determination of the Angular Unit

In this calculator, the following three angular units can be

specified.

Chain Calculations (7)

This calculator allows the previous calculation result to be

used in the following calculation.

For example, you can calculate by ⁄= and s=.

The previous calculation result will not be recalled after enter-

ing multiple instructions.

Fraction Calculations (8)

This calculator performs arithmetic operations and memory

calculations using a fraction, and conversion between a deci-

mal number and a fraction.

• In all cases, a total of up to 10 digits including integer,

numerator, denominator and the symbol (l) can be entered.

• If the number of digits to be displayed is greater than 10, the

number is converted to and displayed as a decimal number.

• A decimal number, variable, or exponent cannot be used in

a fraction.

BATTERY REPLACEMENT

Notes on Battery Replacement

Improper handling of batteries can cause electrolyte leakage

or explosion. Be sure to observe the following handling rules:

• Replace both batteries at the same time.

• Do not mix new and old batteries.

• Make sure the new batteries are the correct type.

• When installing, orient each battery properly as indicated in

the calculator.

• Batteries are factory-installed before shipment, and may be

exhausted before they reach the service life stated in the

specifications.

When to Replace the Batteries

If the display has poor contrast, the batteries require replace-

ment.

Caution

• Keep batteries out of the reach of children.

• Exhausted batteries left in the calculator may leak and

damage the calculator.

• Explosion risk may be caused by incorrect handling.

• Batteries must be replaced only with others of the same

type.

• Do not throw batteries into a fire as they may explode.

Replacement Procedure

1. Turn the power off by pressing @ F.

2. Remove two screws. (Fig. 1)

3. Slide the battery cover slightly and lift it to remove.

4. [EL-509V/EL-531V] Remove the used batteries by prying

them with a ball-point pen or other similar pointed device.

(Fig. 2)

[EL-509VH/EL-531VH] Remove used batteries.

5. Install two new batteries.

[EL-509V/EL-531V] Make sure the “+” side facing up.

[EL-509VH/EL-531VH] First insert the “ – ” side to the

spring. (Fig. 3)

6. Replace the back cover and screws.

7. Press the RESET switch (on the back).

• Make sure that the display appears as shown below. If the

display does not appear as shown, remove the batteries

reinstall them and check the display once again.

(Fig. 1) (Fig. 2) (Fig. 3)

Automatic Power Off Function

This calculator will turn itself off to save battery power if no

key is pressed for approximately 10 minutes.

SPECIFICATIONS

Calculations: Scientific calculations, statistical cal-

culations, etc.

Internal calculations: Mantissas of up to 12 digits

Pending operations: 16 calculations 8 numeric values

(4 numeric values in STAT mode)

Power source: 3V ¶ (DC):

[EL-509V/EL-531V]

Alkaline batteries (LR44) × 2

[EL-509VH/EL-531VH]

Heavy duty manganese batteries

(size AA or R6) × 2

Power consumption: 0.0006 W

Operating time: [EL-509V/EL-531V]

Approx. 2500 hours

[EL-509VH/EL-531VH]

Approx. 15000 hours

when continuously displaying 55555.

at 25°C (77°F).

Varies according to use and other

factors.

Operating temperature: 0°C – 40°C (32°F – 104°F)

External dimensions: [EL-509V/EL-531V]

78.6 mm (W) × 152 mm (D) × 10.5

mm (H)

3-3/32” (W) × 5-31/32” (D) × 13/32”

(H)

[EL-509VH/EL-531VH]

78.6 mm (W) × 166 mm (D) × 19.5

mm (H)

3-3/32” (W) × 6-17/32” (D) × 25/32” (H)

Weight: [EL-509V/EL-531V]

Approx. 75 g (0.166 lb)

(Including batteries)

[EL-509VH/EL-531VH]

Approx. 115 g (0.254 lb)

(Including batteries)

Accessories: Batteries × 2 (installed), operation

manual, operation examples sheet,

quick reference card and hard case

• Calculation ranges

±10

-99

~ ±9.999999999×10

and 0.

If the absolute value of an entry or a final or intermediate

result of a calculation is less than 10

–99

, the value is consid-

ered to be 0 in calculations and in the display.

FOR MORE INFORMATION ABOUT THIS

CALCULATOR

Visit our Web site.

http://sharp-world.com/calculator/

1234567890.,

P (x,y )

P (r,

)

ENGLISH

1234567890.,

Sharp EL531V Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info