Handleiding Shark SV800 (pagina 3 van 13) (Engels, Frans, Spaans)

668682

Verklein

Vergroot

Pagina terug

1/13

Pagina verder

OPERATING INSTRUCTIONS

4. Once the telescopic tube is inserted,

you can adjust the height of the handle

by moving the locking latch past 90

degrees to the open position. Holding

the handle, extend the tube to the

height that is right for you and then

close the latch to the locked position.

(Fig. 3)

Fig. 3Fig. 2

Charging the Battery

NOTE: The battery is packaged

separately from the charging base but it

is not charged. Before using the

vacuum, charge the battery for 24 hours.

NOTE: The charging base can be

mounted on a table top or a wall near an

electrical outlet.

1. When mounting on a wall, make sure

that the intended wall area for the

charging base to be drilled is free

from any hidden electrical wires,

water pipes and gas lines.

2. Select an appropriate place close to a

wall power outlet (120V., 60 Hz).

3. Do not place near direct sunlight,

near a heat source or outdoors.

4. Select an appropriate drill type for the

material to be drilled.

5. Carefully measure and mark the

location of all bracket holes and then

drill holes and screw the charging

base onto the wall. (Screws not

included.)

6. The charge adapter plug is keyed and

will fit into the charging base only one

way. Align the channel on the

adaptor plug with the tab on the

bottom of the charging base. (Fig. 1)

7. Plug the charging adapter into the

closest electrical wall outlet.

8. Place the charging base onto the wall.

Be careful not to pinch the charging

adaptor wire between the wall and the

charging base.

9. Insert the battery into the charging

base to charge. The charging light on

the charging base will light up.

NOTE: The battery must be charged for

24 hours prior to first use. Ensure that the

On/Off switch is in the “Off” position

before inserting the battery.

5. Hold the battery and insert the bottom

part first into the opening found at the

back of the unit. Then rotate in place

making sure that it clicks into place.

(Fig. 4)

Fig. 4

6. Turn the unit “On” to begin

vacuuming.

7. Place your foot lightly on the top of

the motorized brush and rotate the

handle back toward you to release the

unit from the locked upright position.

Fig. 1

Charger base

Charging

adapter

Battery

Charging light

Assembling the Stick Vac

1. Remove all the parts of the stick vac

from the box.

2. Hold the motorized brush and push it

in the base of the stick vac completely.

(Fig. 2)

3. Hold the telescopic tube and push it in

to the top of the handle of the stick

vac. (Fig. 3)

OPERATING INSTRUCTIONS

On/Off Switch

The On/Off switch has three different

positions. (Fig. 5)

1. Push on the "I" side to turn the

vacuum to “LOW” speed.

2. Push on the “II" side to turn the

vacuum to “HIGH” speed.

3. Push on the “O” (middle) to turn the

vacuum to the “Off” position.

Fig. 5

= ON (Low speed)

= OFF

= ON (High speed)

Converting Stick Vac to Hand Vac

1. Press the telescopic release button to

remove the telescopic tube. (Fig. 6)

2. Press the floor brush release button

and remove the motorized floor

brush. (Fig. 6)

Telescopic

tube release

Release

button

Lift

Pull

Fig. 6

3. Insert the crevice tool into the bottom

of the vacuum making sure that it

snaps into place. (Fig. 7) To remove

the crevice tool, press the motorized

brush/crevice tool release button.

Fig. 7

Emptying the Dust Cup

IMPORTANT: Always turn the vacuum

off before removing the dust cup.

1. To remove the dust cup, press the

dust cup release that is on the

bottom of the dust cup. (Fig. 8)

Fig. 8

Dust cup

release

2. Hold the dust cup

cover and twist it

to the left to remove

it from the dust

cup. (Fig. 9)

3. Hold it over a

garbage can and

empty the dust.

(Fig. 10)

IMPORTANT: Empty

the dust cup after every

use. Never use the

vacuum without the

dust cup and filter

in place.

4. To reattach the dust

cup cover, align the

indicators that are

the cover and the

dust cup and turn to

the right to lock in

place. Make sure

that the “▼”

symbol on the top

cover is aligned with

the “▲”symbol

on the dust cup

to lock into

place. (Fig. 11)

Fig. 9

Fig. 10

Fig. 11

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Shark SV800 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info