603061
14
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
14
the utmost care that they are properly aligned during re-
assembly.
Open the freezer door (18).
Remove the xing screws (1 and 3) from the top cover (two
screws at the front and two at the rear), and take off the
cover (4).
Unscrew the upper hinge bracket (5) and remove it.
Caution: the door must be supported while this is done.
Take off the freezer door (18).
Unscrew the hinge pin (7) together with the nut (6) and
washers (8), and t the entire assembly to the opposite side
of the hinge bracket.
Undo the xing screws (11) on the centre hinge bracket (10).
Caution: Support the door.
Take off the centre hinge bracket (10) together with the
hinge pin washers and the plastic plate (9).
Take off the refrigerator door (13).
Tilt the whole unit towards the rear.
Unscrew the lower hinge bracket (14) and take it off.
Unscrew the hinge pin (15) from the bracket, and re-insert it
from the other side.
Remove both screws on the left of the underside and
replace them on the right.
Fit the lower hinge bracket (14) on the left of the underside.
Put the washers on the hinge pin.
Remove the cap (19) from the freezer door and the cap (16)
from the refrigerator door and replace them on the opposite
side of the doors.
Take off the caps (17) from the partition between the
refrigerator and freezer compartments and remove the
screws.
Replace both screws on the opposite side and then the
caps.
Fit the refrigerator door (13) onto the pin (15) of the lower
hinge bracket.
Fit the pin of the centre hinge bracket (10), together with the
washers, to the refrigerator door (13).
Fit the centre hinge bracket (10) together with the plastic
plate (9).
Remove both screws from the upper left and replace them
on the right.
Place the freezer door (18) onto the pin of the centre hinge
bracket.
Fit the pin of the upper hinge bracket (5) to the freezer door
(18), and then t and secure the upper hinge bracket (5).
Note: If necessary, the alignment of the doors can be adjusted
by slightly loosening the hinge bracket screws, but remember
to tighten them afterwards
.
Replace the top cover (4) and use the screws (1 and 3) to
secure it (two screws at the front and two at the rear).
If the unit has been tilted to more than 30°, wait for about 4
hours before re-connecting it to the mains.
Temperature control
The unit is re-activated by connecting it to the mains. It is only
switched off completely when the plug is removed from the wall
socket.
The temperature in the refrigerator cabinet can be adjusted by
setting the temperature control. Turning the control clockwise
will decrease the temperature, while turning it anti-clockwise
will increase it.
The medium settings are usually most suitable for home use.
We recommend using a thermometer to check the actual
temperature inside the cabinet and make adjustments as
necessary.
Following a power interruption, or if the unit has been switched
off on purpose, it may take 3 to 5 minutes before it switches
on again.
In position ‘0’, the cooling function is switched off, though
the appliance is still connected to the mains.
1. Temperature control
2. Control panel cover
3. Bulb
4. Lamp cover
5. Locking mechanism
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Severin KS9785 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Severin KS9785 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info