735538
7
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
Display modes
In DISPLAY MODE the DEFAULT operation is that the sensor alternates between carbon dioxide and
carbon monoxide readings presentation. The push button MENU(+) is used to select the indicated
value on the display to be the error code or the set points of temperature and CO
2
After power up the
display will always return to the Default display mode. If a permanent change of default values is
requested the PC software is to be used.
Function
Line
Display
Time
limit
Function description
0
CO / CO
2
no
DEFAULT - Normal operation
1
Exxx
yes
Error code. If no error has been detected the code E0 is shown. The
error code is reset with Entr(+-).
2
Present CO
and CO
2
.
set points
no
Toggle between display of temperature and CO
2
set point with
MENU(+).
Table III. On the display without entering the maintenance menu
Maintenance level
A number of execution options are available from the MAINTENANCE MENU (see Table IV). This level
is accessed only from the display mode in the set points of CO and CO
2
selection. A two buttons push
and an access code restrict access, intended for competent trained service personnel only. The Entr(+-
)command is done by PUSHING MENU AND ESC AT THE SAME TIME (hold down for about 14
seconds). The access code has eight binary digits; one press at MENU(+) equals 1 and one press at
ESC(-) equals 0. The code value can be changed for your personal choice from the software UIP 4.3.
Always use the ESC button to return to the DEFAULT mode. Several pushes of the ESC button may
be needed to return to the DEFAULT mode. The Entr(+-) push (MENU & ESC) eventually leads to
execution of functions, which causes temporary or permanently change of any parameter, that affects
the system outputs!
Function
Line
Display
Time
limit
Function description
3
ECxx
yes
Access code to the service menu The default value of the code is
255 (=11111111, that is eight presses on MENU(+)). Press down
MENU(+) and let it scroll until it stops. The last two digits of the code
are shown. Then ENTER to accept the selected code.
4a
SPCO
yes
For setting the set point of the CO concentration.
4b
The present
CO set point
yes
For increase / decrease of the CO set point. The set point is
increased by stepping with MENU(+) button. Decreasing is done by
stepping with the ESC(-) button.
5a
SPc
yes
For setting the set point of the CO
2
concentration
5b
The present
CO
2
set point
yes
For increase / decrease of the CO
2
-concentration set point The
set point is increased by stepping with MENU(+) button. Decreasing
is done by stepping with the ESC(-) button.
6a
AOUt
yes
First step of adjusting the analogue outputs MAX and MIN values
6b
An xx
no
Select analogue output by stepping with MENU(+) button
6c1
SetL
no
Leads to adjustment of the MIN value.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Senseair aSENSE M III bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Senseair aSENSE M III in de taal/talen: Engels als bijlage per email.

De handleiding is 1,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Senseair aSENSE M III

Senseair aSENSE M III Installatiehandleiding - English - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info