Handleiding Sencor SWK 7705 (pagina 7 van 8) (Engels)

759142

Verklein

Vergroot

Pagina terug

1/8

Pagina verder

- 7 - 09/2020

EN Variable temperature

electric kettle

User'smanual

■ Prior to using this appliance, please read the user'smanual thoroughly, even in cases,

when one has already familiarised themselves with previous use of similar types of

appliances. Only use the appliance in the manner described in this user’smanual.

Keep this user'smanual in asafe place where it can be easily retrieved for future use.

In the event that you hand this appliance over to somebody else, make sure to also

include this user'smanual.

■ Carefully unpack the appliance and take care not to throw away any part of

the packaging before you find all its parts. We recommend saving the original

cardboard box, packaging material, purchase receipt and responsibility statement

of the vendor or warranty card for at least the duration of the legal liability

for unsatisfactory performance or quality. In the event of transportation, we

recommend that you pack the appliance in the original box from the manufacturer.

DESCRIPTION

A1 Lid

A2 Spout with filtration strainer (inside)

A3 Base stand

A4 Open lid button

A5 Control panel

A6 Handle

A7 Central connector

A8 Power cord

A9 Power cord groove

B1 Temperature setting LED indicators

B2 Set temperature button - 60, 70, 80

or 90°C

B3 On/Off button

BEFORE FIRST USE

■ Remove all wrapping material from the electric kettle and its base stand.

■ Fill the kettle with clean water up to its maximum water mark (MAX). Boil the water

and empty the contents of the kettle. Repeat this process 2 to 3 times. To boil water,

proceed according to the instructions in chapter Operation.

OPERATION

Attention:

The electric kettle is intended only for heating water. Never heat

any other liquids or substance in it.

■ Set the required power cord length and push it into the groove in the base stand.

Place the base stand on astable, even and clean surface.

■ Fill the kettle with the required amount of water. You may fill it through the spout

or through the opening after lifting the lid. To open the lid, press button A4. The

water level must reach at least the minimum mark (MIN) but must not exceed the

maximum mark (MAX). After filling the kettle, properly close the lid.

Attention:

Never fill the kettle when it is placed on the base stand.

Turning on and stand-by mode

■ Place the kettle on the base stand and insert the power cord plug into apower

socket. The kettle will beep and all the LED indicators will light up for a few

moments, and the backlight of button B3 will start flashing. In this way the kettle

enters the stand-by mode, meaning that it is ready for operation.

Heat Water to 100°C

■ When button B3 is pressed in the stand-by mode, the kettle will beep, start heating

the water and button B3 will remain permanently lit.

Attention:

Never start the kettle empty without water. The incorrect use of

the kettle may negatively affect its working order and lifetime.

■ When the temperature of the water reaches 100 °C, the kettle will beep and

automatically switch to the stand-by mode.

Note:

The operation of the kettle can be stopped at any time by pressing

button B3.

■ Pour the boiled water into aprepared container, cup or mug. When carrying it, hold

the kettle upright, particularly when it is filled all the way up to the maximum mark.

■ If you wish to fill the kettle again and start heating immediately after pouring in

the water, wait approximately 30–60 seconds. When opening the lid, be especially

careful to avoid scalding yourself with boiling water or steam.

Heating water to aset temperature then maintaining temperature

■ Press button B3 and then repeatedly press button B2 to select atemperature of 60,

70, 80 or 90°C. The LED indicator of the selected temperature will start flashing and

water will start being heated.

■ The maintain temperature function will also be activated when the selected

temperature is reached. This function automatically switches the heating element

on and off to maintain the selected temperature. The maintain set temperature time

is preset to 2 hours. After this time has elapsed, the kettle will turn off automatically.

If you wish to end this function earlier, press button B3 or lift the kettle off the base

stand.

Note:

This kettle is not calibrated for scientific or laboratory purposes. The

actual water temperature may differ by ±5°C from the selected water

temperature.

Note:

When using the maintaining temperature mode, consider whether this

function is really necessary. You will contribute to lowering the impact

of electrical appliances on the environment.

Turning off

■ To turn off the kettle after use, press button B3. The button will turn off and the

kettle will turn off.

■ When not using the kettle, empty it out and place it away from the base stand.

■ When not using the kettle for an extended period of time, we recommend

disconnecting the power cord from the power socket.

■ Protection against boiling without water

■ If you accidentally turn on the kettle without water it, after reaching a certain

temperature, the kettle will beep and the thermostat will automatically disconnect

the electric circuit. The kettle can be used again after several minutes, once the

heating bottom has cooled down.

Attention:

Even though the kettle is equipped with protection against boiling

without water, do not turn it on when empty. The incorrect use of

the kettle may negatively affect its working order and lifetime.

CLEANING AND MAINTENANCE

Attention:

Prior to any cleaning or maintenance, always disconnect the base

stand from the power socket and allow the kettle to cool down.

Do not wash the kettle, its base stand or power cord under

running water and do not submerge them in water or another

liquid.

■ To clean the external parts of the kettle, use adry cloth or acloth dipped in aweak

solution of neutral kitchen detergent. Never use solvents, cleaning products with an

abrasive effect, etc. After washing, wipe the surface with aclean, lightly dampened

cloth and then wipe dry.

■ Wipe the internal parts of the kettle using asoft sponge or clean cloth dipped in

clean warm water. Do not use detergents or any other chemical agents on the

internal parts. After cleaning the kettle, rinse it out several times with clean water.

■ To clean the base stand, use only adry cloth.

Cleaning the filtration strainer

■ The removable filtration strainer serves to capture limescale, preventing it from

getting into the cup together with the water. Regularly clean the filter under running

water using afine nylon brush or submerge it for several hours into avinegar - water

solution (recommended dilution ratio 1:2). After applying the solution, rinse the

filter under clean running water.

Removing limescale deposits

■ During normal use, substances contained in water accumulate on the appliance to

form so-called limescale deposits. These may negatively affect the lifetime of the

kettle and ruin the taste and appearance of your beverage, so it is important to

regularly remove them based on how frequently the kettle is used.

■ When using the kettle at afrequency of 3 to 5 times per day, we recommend to

remove water scale deposits:

– once per month in areas with hard and very hard water;

– once every two to three months in areas with soft and medium hard water.

■ Limescale deposits can be cleaned away using standard available limescale removal

products (according to the manufacturer'sinstructions) or use:

– 8% white vinegar, generally available in stores. Fill the kettle with 1 litre of water

and¼ litre of vinegar. Bring the solution to aboil and leave it to act in the kettle

for 2 hours. Then empty the kettle and before further use, boil clean water in it

four to five times.

– citric acid. Boil 1 l of water in the kettle, into the boiled water, add 30 g of citric

acid and allow the solution to act for about 30 minutes. Then empty the kettle and

before further use, boil clean water in it four to five times.

TECHNICAL SPECIFICATIONS

Rated voltage range ............................................................................................................ 220−230 V

Rated frequency........................................................................................................................50/60 Hz

Rated power input ...................................................................................................... 1,850 - 2,150 W

Volume .................................................................................................................................................. 1.7l

Weight ...................................................................................................................................................1 kg

Changes to text and technical parameters are reserved.

Sencor SWK 7705 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info