759128
5
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
12/2018
- 5 -
Copyright © 2018, Fast ČR, a.s.
EN
Variable Temperature
Electric Kettle
User'smanual
■ Prior to using this appliance, please read the users manual thoroughly, even
in cases, when one has already familiarised themselves with previous use of
similar types of appliances. Only use the appliance in the manner described in
this user’smanual. Keep this usersmanual in asafe place where it can be easily
retrieved for future reference.
■ We recommend saving the original cardboard box, packaging material,
purchase receipt and responsibility statement of the vendor or warranty card
for at least the duration of the legal liability for unsatisfactory performance
or quality. In the event of transportation, we recommend that you pack the
appliance in the original box from the manufacturer.
DESCRIPTION OF THE KETTLE
A1 Open lid button
A2 Lid
A3 Spout
A4 Filtration strainer
(cannot be removed)
A5 Water level mark
A6 Base with acentral connector
A7 Control panel
A8 Handle
A9 LED light for the inside of the
kettle
DESCRIPTION OF THE CONTROL PANEL
B1 Temperature setting LED indicators
B2 On/O button
B3 Set temperature button – 50, 70, 80 or 90 °C.
BEFORE FIRST USE OF THE KETTLE
1. Remove all wrapping material from the kettle and its base A6.
2. Fill the kettle with clean water up to the maximum water mark. Boil the water
and empty the contents of the kettle. Repeat this process 2 to 3 times.
Note:
To boil water in the fast boil kettle proceed according to the instructions
in chapter Using the kettle.
3. Now the kettle is ready for operation.
USING THE KETTLE
1. Set the desired length of the power cord. Push the power cord into the groove
in the base A6. Place the base A6 on astable, even and clean surface.
2. Press button A1 to open the lid A2, then ll the kettle with the required amount
of water. The water level must reach at least the minimum mark (0.5l) and must
not exceed the maximum mark (2l). After lling it, close the lid A2 and make
sure that it is secured in the closed position.
Attention:
Do not ll the kettle when it is placed on the base A6.
When lling the kettle, there is arisk of water splashing out.
3. Place the kettle on the base A6 and insert the power cord plug into apower
socket. When the power cord is connected to apower socket, ashort beep will
be made and all the LED indicators B1 and the LED light A9 will light up for an
instant and another beep will be made. The kettle will then switch to stand-by
mode and is ready for use. The default temperature setting is 100 °C.
4. Possible uses of the kettle:
4.1 Boil water
■ To start the water boiling process, press button B2. Abeep conrms that the
button was pressed. The kettle will start heating water to 100 °C. The LED light
A9 is lit red. When the water starts to boil, the kettle will turn o automatically.
Two beeps are made and the LED light A9 will turn o.
Note:
The water boiling process can be stopped at any time by again pressing
button B2.
4.2 Heating water to aselected temperature
■ Use button B3 to set the heating temperature 50, 70, 80 or 90 °C. The
temperature setting changes each time button B3 is pressed. Each press of the
button is accompanied by ashort beep. The temperature setting is signalled by
the respective LED indicator B1 being lit. To start the process of heating water
to the set temperature, press button B2. LED light A9 will be lit:
green when temperature is set to 50 °C;
blue when temperature is set to 70 °C;
violet when temperature is set to 80 °C;
orange when temperature is set to 90 °C;
■ When the water is heated to the set temperature, the kettle will turn o
automatically. Two beeps are made and the LED light A9 will turn o. LED
indicator B1 remains lit for approximately one minute after it is turned o. Then
it turns o and the kettle switches to the stand-by mode.
Note:
If you set atemperature using button B3 and then do not press button B2
to start the water heating process, after 15 seconds the kettle will switch
to the stand-by mode and the respective LED indicator B1 will turn o.
The temperature setting can be changed while the appliance is running.
The process of heating water to aset temperature can be stopped at any
time by again pressing button B2.
If you set atemperature that is lower than the current temperature of the
water inside the kettle, abeep will be made after button B2 is pressed and
the kettle will turn o automatically.
4.3 Keep warm mode
■ This mode is usually used when you wish to heat water to a required
temperature and then maintain it at this temperature, or when you wish to boil
water and then keep it warm.
■ Use button B3 to select the required temperature 50, 70, 80, or 90 °C. The
respective LED indicator B1 will be lit. Press button B2 and hold it down for
approx. 3 seconds. The respective LED indicator B1 will start ashing, the
coloured LED light A9 will be lit as described in point 4.2 and the process of
heating water to the set temperature will start. When the set temperature is
reached, two beeps are made and the kettle automatically switches to the keep
warm mode. In this mode, the heating element automatically switches on and
o to maintain the set temperature. The keep warm mode ends automatically
after 30 minutes. Two short beeps are made, the LED light A9 and the respective
LED indicator B1 will turn o, and the kettle will switch to the stand-by mode.
■ Using the above described method, it is possible to set the keep warm mode
after previously boiling or heating water according to described points 4.1 and
4.2. If, for this mode, you set atemperature that is lower than the current water
temperature inside the kettle, two beeps will be made when the kettle is started.
This signals that the set temperature has already been reached. Water will cool
down to the set temperature and will then be maintained at this temperature.
The keep warm mode ends automatically after 30 minutes.
■ To quickly switch the kettle from the stand-by mode to the keep warm mode,
press and hold down button B2 for 3 seconds. Water will be maintained at
atemperature of 50 °C.
Note:
If you set atemperature using button B3 and then do not press button B2
to start the maintain set temperature mode, after 15 seconds the kettle
will switch to the stand-by mode and the respective LED indicator B1 will
turn o.
It is not possible to change the set temperature in the keep warm mode.
The keep warm mode can be stopped at any time by pressing button B2.
Attention:
If the kettle is not located on the base A6, the buttons on the control
panel A7 will not react to being pressed.
Lifting the kettle o the base will cancel all previous settings. When the
kettle is placed back on to the base A6, ashort beep will be made and all
the LED indicators B1 and the LED light A9 will light up for an instant and
another beep will be made. The kettle will then again switch to stand-by
mode and is again ready for use.
This kettle is not calibrated for scientic or laboratory purposes. The actual
water temperature may dier by ±5 °C from the set water temperature.
Attention:
Do not turn on the kettle when it is empty. Incorrect use may negatively
aect its lifetime. If you accidentally turn on the kettle without water
inside, after ashort time asound will be made, the LED light A9 will turn
o and the kettle will turn o. Wait until the heating element cools down.
This is indicated by asound and all the LED indicators B1 and the LED
light A9 turning on for an instant. Then the kettle will switch to stand-by
mode and is again ready for use.
5. Pour the boiled or heated water into aprepared container, cup or mug. Make
sure that the kettle remains in avertical position when it is carried, particularly if
it is lled all the way up to the maximum mark.
6. If you wish to open the kettle to rell it, be especially careful when opening the
lid A2 to avoid scalding by the escaping steam.
7. After you nish using it, disconnect the power cord from the power socket.
Empty the kettle and allow it to cool down.
CLEANING AND MAINTENANCE
1. Removing limescale deposits
■ Limescale deposits inside the kettle may negatively aect its lifetime, so it is
important to regularly remove it based on how frequently the kettle is used.
During standard use (3 to 5 times per day), we recommend water scale deposits
be removed:
once per month in areas with hard and very hard water;
once every two to three months in areas with soft and medium hard water.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SWK 2194 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SWK 2194 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sencor SWK 2194

Sencor SWK 2194 Gebruiksaanwijzing - Nederlands - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info