Handleiding Sencor STM 6377 (pagina 9 van 10) (Engels)

758575

Verklein

Vergroot

Pagina terug

1/10

Pagina verder

- 9 - 04/2021

Attention:

Do not use ngers or other items to push the ground meat in.

Always use the pusher B1 designed for this purpose.

3. To turn o the appliance, set the speed control knob A12 to the OFF position.

4. Clean out the individual parts of the attachment after each use according to the instructions

in chapter Cleaning and maintenance.

ASSEMBLING AND DISASSEMBLING THE COOKIE MAKER ATTACHMENT

1. Proceed in the same way as when assembling the meat grinder, only with the dierence that

instead of the grinding blade B6 and the grinding plate B8, B9 or B10 only parts B11,B15

and B16 are used.

2. Place the separator B11 on to the screw shaft so that the notch in the grinding chamber B4

ts into the groove in the separator B11. Insert the cookie maker holder B16 into the screw

ring B7. Screw the screw ring B7 clockwise on to the grinding chamber B4. Complete the

assembly by inserting the cookie maker B15 into the holder B16 and attaching the hopper

B2 to the feed tube B3.

3. Attach the attachment to the food processor in the same way as described in point 4 in

chapter Assembling and disassembling the meat grinder.

4. When disassembling, rst remove the hopper B2. Then press the button A1 and remove the

attachment by turning it clockwise. After removing the attachment, put the cover A2 back

in its place.

5. When disassembling the attachment into its individual parts, proceed in the reverse

sequence.

USING THE COOKIE MAKER ATTACHMENT

1. Place the prepared dough on to the hopper B2. Slide the cookie maker B15 to the left or

right to set the desired cookie shape.

2. Insert the power plug into apower socket. Set the required speed using the speed control

knob A12. When starting it for the rst time, we recommend that you set speed 3 and then

increase or decrease it as required.

3. Use the pusher B1 to push the dough through the feed tube B3. The food processor will

push the dough out in the required shape that you set using the cookie maker B15.

We recommend that you place atray or your palm underneath the pushed out dough. Then

cut the formed dough into smaller pieces.

Attention:

Do not use ngers or other items to push the dough in. Always

use the pusher B1.

4. When you have nished using the food processor, turn it o by setting the speed control

knob A12 to the OFF position.

5. Clean out the attachment after each use according to the instructions in chapter Cleaning

and maintenance.

BLENDING

ASSEMBLING AND DISASSEMBLING THE BLENDER

1. On to the blending jar C4, place the outer lid C2 so that its edges copy the neck of the jar,

and push it down thoroughly along its entire perimeter. Into the hole in the lid C2, place the

inner cap C1 and push it down all the way.

2. Make sure that the food processor is turned o and disconnected from the power socket.

The multi-function head A7 must be tilted down in the horizontal position and the whisk,

beater or kneading attachments must be removed. Release and remove the top attachment

hub cover A6. Place the assembled blending jar on to the top hub and pulling it gently

turn it in the direction of the symbol all the way. The safety mechanism will prevent the

blender from starting unless it is correctly secured to the multi-function head A7.

3. To disassemble proceed in the reverse sequence.

USING THE BLENDER

1. The blender is intended for preparing meals and drinks such as milkshakes, creamy soups,

sauces, spreads, fresh baby foods, etc. It is not intended for juicing fruit and vegetables,

preparing potato purée, yeast dough or for whipping egg whites.

2. Assemble the blender according to the instructions in chapter Assembling and

disassembling the blender, and put the ingredients (larger pieces need to be cut up in

advance) into the blending jar C4.

Note:

The maximum capacity of the blending jar C4 is 1.5 litres. Never ll it past

the maximum mark. When processing hot liquids or liquids that expand in

volume during the blending process, it is recommended to ll the blending

jar to no more than ⅔ of its maximum capacity.

3. Make sure that the food processor is correctly assembled and that the speed control knob

A12 is set to the OFF position. Connect the power cord to apower socket. Set the required

speed using the speed control knob A12. We recommend to rst set aslower speed to

allow the ingredients to mix together. Then the speed may be increased. The pulse level

is appropriate when you wish to blend food only very quickly. To start the pulse level, turn

the speed control knob A12 to the PULSE position and hold it in this position for amoment.

As soon as you release the speed control knob A12, it will automatically return to the OFF

position.

Attention:

Hot liquids up to a temperature of 55 °C may be processed in

the blending jar. The maximum operating time of the blender is

2 minutes. Do not leave the appliance in continuous operation

for longer than indicated above. Then allow it to cool down for

30 minutes.

4. While blending, you may add food or liquids to the blending jar C4 through the hole in the

lid C2 after removing the inner cap C1. Never open the outer lid C2 during operation. When

processing hot liquids, the inner cap C1 must remain closed.

5. In the event that food is sticking to the blade assembly C6 or the walls of the blending jar

C4, turn the appliance o by turning the speed control knob A12 to the OFF position and

disconnect it from the power socket. Make sure that the blade assembly C6 has stopped

rotating. Carefully remove the assembled blending jar from the multi-function head A7 by

turning it in the direction of the symbol . Take o the lid and using a plastic spatula,

clean the blade assembly C6 and the inside of the blending jar C4. Put the lid back on and

reattach the blender assembly to the multi-function head A7. Plug the power cord into

apower socket and continue blending.

6. After you have nished using the appliance, set the speed control knob A12 to the OFF

position and disconnect the power cord from the power socket. Check that the blade

assembly C6 has stopped rotating and carefully take the blending jar assembly o the multi-

function head A7. Put the cover A6 back in its place and use asoft plastic spatula to remove

food from the blending jar C4.

7. Disassemble the assembled bowl and clean the individual parts after each use according to

the instructions in chapter Cleaning and maintenance.

ADVICE AND TIPS FOR BLENDING

■ First cut food with a rm consistency such as fruit and vegetables into smaller pieces

measuring 3 cm and only then blend it.

■ First, blend a smaller amount of ingredients and then gradually add more ingredients

through the hole in the lid C2 while blending. In this way, you will achieve better results

than by adding all ingredients into the blending jar C4 at once.

■ If you need to blend food of asolid consistency together with liquids, we recommend that

you rst blend the food of solid consistency and apart of the liquids. Then gradually add the

remaining liquids through the hole in the lid C2 while blending.

■ To blend very thick liquids, we recommend using the pulse level so that the blade assembly

C6 does not get jammed too often. Start the blender repeatedly in short intervals.

■ Ice cubes must be processed immediately upon being removed from the freezer. When the

ice starts to melt, the ice cubes will stick together and it will not be possible to blend them.

QUICK GUIDE TO PROCESSING INGREDIENTS

Ingredients Speed selection Recommended

blending time

Fruit, vegetables cut into smaller pieces 5–6 30 s

Baby food 5–6 40 s

Spreads, dressings, marinades 3–4 30 s

Smoothies and cocktails 6 to MAX 40 s

Soups 6 to MAX 30 s

Ice cubes PULSE

Note:

The above food processing times are only areference. The actual blending

time depends on the size of the ingredients, their amount and the required

nal consistency.

GRATING AND SLICING

PURPOSE OF THE GRATING AND SLICING ATTACHMENT

■

The attachment is designed for slicing and grating fruit and vegetables, cheeses, chocolate,

nuts, for making breadcrumbs, etc.

■ The table Choosing the right type of grating cone will help you to select the right type.

ASSEMBLING AND DISASSEMBLING THE GRATING AND SLICING ATTACHMENT

1. Select one of the grating cones B5–B9 and insert it into the chamber B3, so that the shaft

inside the chamber B3 slides into the pentagonal hole in the centre of the grating cone.

Seat the locking pin B4 on to the shaft, and then turn it to secure the grating cone inside

the chamber B3. Attach the chute B10 to the chamber B3.

2. Make sure that the food processor is turned off and disconnected from the power socket.

The arm of the food processor must be tilted down in the horizontal position and the

blender, beater or kneading attachments must be removed. Remove the front cover

from the multi-function head of the food processor, and push the assembled attachment

at an angle of 45° against the front attachment hub and secure it in place by turning it

anticlockwise, see figure D.

3. The attachment is securely mounted in the vertical position when the button located on

the left of the front attachment hub slides out. An audible click is made when the button

slides out. The attachment is assembled when the pusher B1 is inserted in the feed tube

B2. The attachment is now assembled and ready for use.

4. When removing an attachment, first press the button located on the left of the front

attachment hub, and then remove the attachment by turning it clockwise. When

disassembling the attachment into its individual parts, proceed in the reverse sequence.

USING THE GRATING AND SLICING ATTACHMENT

1. Prepare the ingredients and cut them into pieces that will pass through the feed tube B2.

Remove hard kernels or stones from the fruit and vegetables. Remove shells from nuts.

Sencor STM 6377 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info