758521
12
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
EN-12
EN
Food Processor
STM 40WH / STM 41GR / STM 42BL / STM 43OR
STM 44RD / STM 45VT / STM 46YL / STM 47GG / STM 48RS
2014
11/2014
ASSEMBLING AND DISASSEMBLING THE SAUSAGE STUFFER ATTACHMENT
1. When assembling the sausage stuffer for fi lling sausage casings (making sausages), proceed in
the same way as when assembling the meat grinder, only with the difference that instead of the
grinding blade B6 and the grinding plate B8 or B9 only parts B0 and Bqa are used.
2. Place the separator B0 on to the screw shaft so that the notch in the grinding chamber B4 ts into
the groove in the separator B0. Place the sausage stuffer attachment Bqa on to the separator B0
and complete the entire sausage stuffer assembly by screwing the screw cap B7 on to the grinding
chamber B4.
3. To disassemble proceed in the reverse sequence.
USING THE SAUSAGE STUFFER ATTACHMENT
1. Make sure that the appliance is correctly assembled and that the speed control knob Aqa is set to
the OFF position. Insert the power plug into an electrical power socket.
2. Prepare a sausage casing that you will stuff with ground meat and allow it to soak in lukewarm
water for approx. 10 minutes. Place the ground meat mixture on to the hopper B2. Take the
sausage casing out of the water and skewer or tie up one end and slide the other end like a sock
on to the sausage stuffer attachment Bqa.
3. Use the speed control knob Aqa to set the desired speed. We recommend to initially set the lowest
speed and then increase it as required. With one hand hold the sausage casing on the attachment Bqa
and use the other hand to push the ground meat mixture with the pusher B1 through the feed tube
B3. If the sausage casing sticks to the attachment Bqa, it is necessary to moisten it with water again.
Attention:
Do not use fi ngers or other utensils to push the ground meat through the feed tube B3. Always
use the pusher B1 designed for this purpose.
4. To turn off the appliance, set the speed control knob Aqa to the OFF position.
5. Clean out the individual parts of the attachment after each use according to the instructions in
chapter Cleaning and maintenance.
ASSEMBLING AND DISASSEMBLING THE KEBAB MAKER ATTACHMENT
1. When assembling the kebab maker attachment, proceed in the same way as when assembling the
meat grinder, only with the difference that instead of the grinding blade B6 and the grinding
plate B8 or B9 only parts Bqs a Bqd are used.
2. Place the moulder Bqs on to the screw shaft so that the notch in the grinding chamber B4 ts
into the groove in the moulder Bqs. Place the kebab moulder attachment Bqs on to the conical
attachment Bqd and complete the entire kebab maker assembly by screwing the screw cap B7 on
to the grinding chamber B4.
3. To disassemble proceed in the reverse sequence.
USING THE KEBAB MAKER ATTACHMENT
1. Make sure that the appliance is correctly assembled and that the speed control knob Aqa is set to
the OFF position. Insert the power plug into an electrical power socket.
2. Place the ground kebab meat mixture on to the hopper B2. Use the speed control knob Aqa to
set the desired speed. We recommend to initially set lower speed and then increase it as required.
Using the pusher B1, push the mixture through the feed tube B3. The result will be a hollow meat
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor STM 46 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor STM 46 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info