759893

Sencor SSI 0710 Handleiding

6
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
- 6 - 11/2019
Copyright © 2019, Fast ČR, a.s.
EN Steam station
User'smanual
DESCRIPTION OF THE APPLIANCE AND ACCESSORIES
A1 Steam station
Stand with compartment for power
cord and steam hose
A3 2-litre water tank
A4 Carry handle
A5 Iron rest surface
A6 Holder for steam hose and power
cord
A7 Power cord
A8 Steam hose
A9 Control panel
A10 Iron
B1 Water tank unit
B2 Filling opening lock
B3 Cassette with filter against limescale
and dirt
B4 Spring latch
Serves to release and attach the
water tank to the steam station.
B5 Cassette plug
C1 On/Off button
C2 Steam mode selection button
C3 Limescale protection system reset
button
C4 Power On indicator
C5 Power-saving mode indicator
(ECOmode)
C6 MAX steam output indicator
(MAXmode)
C7 Replacement of limescale and dirt
filter required indicator
D1 handle
D2 Temperature dial with automatic
steam regulator
D3 Soleplate
D4 Steam button
D5 Temperature indicator
D6 Rest surface
BEFORE FIRST USE
■ Prior to using this appliance, please read the user’smanual thoroughly, even in cases,
when one has already familiarised themselves with previous use of similar types of
appliances. Only use the appliance in the manner described in this user’smanual.
Keep this user’smanual in asafe place where it can be easily retrieved for future use.
In the event that you hand this appliance over to somebody else, make sure to also
include this user’smanual.
■ We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least the
duration of the legal liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance in the original box
from the manufacturer.
■ Before first use, remove all packaging materials including promotion stickers
and labels from the steam station and iron. Wipe the soleplate D3 with alightly
dampened cloth before first use and then wipe dry.
PREPARATION BEFORE IRONING
■ Sort the laundry according to international symbols shown on the textiles or
according to the fabric types.
SYMBOL FABRIC TYPE SETTING THE
TEMPERATURE
Synthetics (acrylic, acetate,
polyester, viscose, etc.)
•
Low temperature
Cotton with addition of other
types of fibres; silk, wool, wool
with addition of other types of
fibres, etc.
••
Medium temperature
Corduroy, cotton, denim •••
High temperature
Flax MAX
maximum temperature
Fabrics, that should not be ironed
USING THE STEAM STATION
FILLING THE WATER TANK
■ Before filling the water tank A3, check that the steam station is disconnected from
the power socket.
■ The steam station is intended for use with tap water. Limescale deposits may quickly
form, if you live in an area with hard or very hard water. Therefore, to extended the
lifetime of the iron, we recommend using a mixture of 50% tap water and 50%
distilled water.
Attention:
Never add water softeners, vinegar, starch, descaling agents, perfumes
or other additives to the water.
■ Position the steam station on astable, even surface. Hold the steam station A1 with
one hand and press the spring latch B4 on the underside of the water tank A3 with
the other, and then slide out the water tank A3. Slide out the filling opening lock B2
and fill up the water tank A3 with water. When doing this, ensure that you do not fill
past the level marked as MAX.
■ The water tank A3 can also be filled up without sliding it out of the steam station A1.
In such acase, tilt open the filling opening lock B2 and fill the water tank A3 with
water up to the MAX mark using asuitable container.
Note:
The non-stop system enables water to be added to the water tank A3
even while the steam station is in operation without having to turn it
off.
■ Insert the water tank A3 back into the steam station A1. Correct insertion of the
water tank A3 is accompanied by an audible click from the spring latch B4.
TURNING ON
■ Connect the power cord of the steam station to apower socket. Indicator C4 will
be lit and indicator C6 will start flashing, which indicates that the steam station is
heating up. Once the indicator C6 is lit permanently, the steam station is ready for
use.
■ Using the temperature dial D2 on the iron, set the desired temperature. Temperature
indicator D5 will be lit indicating that the iron is heating up. Once the iron’sinternal
thermostat reaches the correct temperature, indicator D5 will turn off.
PUTTING THE IRON ASIDE WHILE IRONING
You may put the iron aside while ironing on the rest surface D6 on the underside of the
iron or on to rest surface A5 on the steam station A1.
IRONING WITHOUT STEAMING
■ This function enables the iron to be used with or without water in the tank A3.
■ Set the temperature dial D2 on the iron A10 to MIN and wait until indicator D5 turns
off.
IRONING WITH STEAM
■ The steam station is equipped with two steam release intensity levels:
ECO: This mode is intended for sufficient steam output for standard ironing with
low power use; it uses less steam and saves power without affecting the
ironing result. Selection of the ECO mode is indicated by agreen illumination
of indicator C5.
MAX: This mode is intended for maximum steam output for demanding or vertical
ironing. Selection of the MAX mode is indicated by a blue illumination of
indicator C6.
Attention:
In order to iron with steam, the water tank A3 must be filled with water.
■ If you wish to iron with steam, set the temperature dial D2 on the iron A10 to an
appropriate temperature and wait until indicator D5 turns off.
Note:
Indicator D5 may turn on and off while ironing, indicating that
temperature is automatically being maintained without interruption
to the ironing process.
■ Press button C2 on the control panel A9 to select steam mode ECO or MAX and wait
until the indicator of the selected mode remains permanently lit.
Note:
When steam ironing after selecting the steam mode on a cold
steam station, it is necessary to hold down button D4 on the iron
for approximately 2 minutes in order for steam to evenly spread
throughout the entire steam circuit system.
■ Holding down button D4 on the iron, will start releasing steam while ironing.
■ If you wish to stop releasing steam, release button D4.
■ We recommend to select the ECO mode for all standard ironing tasks. Only when
ironing linen fabrics, strong silk or similar fabrics is it recommended to select the
MAX mode.
IRONING WITH VERTICAL STEAM
■ The steam station can also be used when ironing hanging textiles (e.g. curtains,
garments hanging on coat hangers, etc.).
■ Set the temperature dial D2 on the iron A10 to MAX and wait until indicator D5
turns off. Position the iron into avertical position. Use one hand to gently tension
the fabric and vertically move the iron vertically from bottom up and press button
D4 to release steam.
Tip:
When ironing cotton or linen textiles, gently place the iron with the
soleplate D3 on to the fabric. When ironing finer or delicate textiles,
keep the iron approximately 2 cm off the fabric.
Do not use the steam function for silk and synthetics so as not to
damage the fabric.
Attention:
Never point the steam at people!
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SSI 0710 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SSI 0710 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info