759460
10
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
- 10 - Copyright © 2020, Fast ČR, a.s. 07/2020
Cancelling scheduled cleaning
Hold down the button E3 (PLAN). The set automatic cleaning time will start flashing
on the display E2.
Hold down button E9 (ON/OFF) until 00:00 appears on the display. Pressing button
E9 again will cancel the set time and the vacuum cleaner will beep 2x.
Hold down button E3 (PLAN) to return to the display of the system time.
CHARGING THE ROBOTIC VACUUM CLEANER
AUTOMATIC CHARGING
As soon as the vacuum cleaner detects low voltage of the battery during operation,
it will automatically start to seek out the charging station. In order for it to find it and
dock, it needs to find the infrared signal transmitted by the charging station. For this
reason, we recommend leaving the charging station constantly connected to the
power source and located in accordance with the instructions provided in chapter
LOCATION OF THE CHARGING STATION.
After docking in the charging station, the charging cycle will commence. Acomplete
charge takes approximately 4 to 7 hours. The actual charging time depends on the
power level of the battery. A fully charged battery will provide up to 90 minutes
of operation.
During the charging process, the indicator light on button A2 will flash red.
When the battery is fully charged, the indicator light of button A2 will remain
permanently lit blue and the process will end automatically.
In the event that the charging contacts are disconnected during the charging cycle,
the vacuum cleaner will move away from the charging station and then re-dock
itself to resume the charging process, unless it is prevented from doing so by an
obstacle. In the event of apower outage, the charging cycle will be interrupted and
will continue after the power supply is renewed. In the event that the maximum
charging current is exceeded, the charging station will automatically interrupt the
charging cycle.
MANUAL CHARGING
If the vacuum cleaner is located away from the charging station and detects alow
battery voltage then button A2 will start flashing red 2x per second. Press button E4
(HOME) on the remote control. The vacuum cleaner will automatically seek out the
charging station and start automatic charging as described in the previous chapter.
If the battery is so flat that the vacuum cleaner is unable to seek out the charging
station then it is necessary to dock the vacuum cleaner into the charging station
by hand. Grasp the vacuum cleaner and manually place it into the charging station
so that the charging contacts on the underside of the vacuum cleaner and the
charging contacts on the charging station are connected. When the contacts are
connected, charging will start.
The vacuum cleaner can also be charged without using the charging station. Insert
the power adapter connector into socket A5 on the side of the vacuum cleaner and
insert the power adapter plug into amains socket.
CARING FOR THE BATTERY
We recommend that you do not interrupt the charging cycle and maintain the
battery in acharged state.
Do not leave the vacuum cleaner standing fully charged or completely flat for an
unnecessarily long period of time.
Abattery that is allowed to remain flat for along time may self-discharge below
apermissible level and thereby cause irreparable damage to itself.
MEANINGS OF AUDIO AND LIGHT SIGNALS OF THE VACUUM
CLEANER
AUDIO SIGNAL
NUMBER OF BEEPS FUNCTION OR STATE
3× short beep Stand-by mode
1× short beep Charging
5× short beep Fully charged
1× short beep Setting of scheduled cleaning successful
2× short beep Scheduled cleaning cancelled
4× short beep Low battery voltage
2× short beep Entry into sleep mode
3× short beep Waking from sleep mode
1× long beep
Power cord is disconnected
Error of the front bumper bar or anti-collision switch
Rubber wheels are off the floor or the vacuum cleaner
was lifted
Overloading of the rubber wheels, rotary brush or side
brushes
LIGHT SIGNALS
FLASHING
BUTTON A2 MEANING SOLUTION
red 4× per
second
The dust container is
incorrectly inserted or
is not inserted at all
Check the dust container.
Charging error
There was apower outage while the
vacuum cleaner was being charged.
Charging will automatically continue
once power is restored. If not, press the
HOME button on the remote control
or put the vacuum cleaner on to the
charging contacts by hand. Check
that the power adapter is correctly
connected to the charging station
and that the power plug is properly
inserted in apower socket. Start the
charging process again. If the vacuum
cleaner does not start charging, contact
aservice centre.
2× red
1× blue
Anti-collision sensor
error
The anti-collision sensor or the bumper
bar is dirty. Clean the bumper bar. If this
does not help, contact aservice centre.
2× red
2× blue
One of the anti-fall
sensors has detected
an area into which
the vacuum cleaner
could fall.
Move the vacuum cleaner to adifferent
location where there is no risk of afall.
3× red
1× blue
Error on one or both
rubber wheels
Check that the wheel is turning freely
and if necessary remove any dirty
material preventing the movement of
the wheel.
1× red
1× blue
Error on the side
brushes
One of the side brushes is jammed due
to dirty material.
Remove any dirt or grime.
1× red
2× blue Central brush error The brush is jammed due to dirty
material. Remove any dirt or grime.
1× red
3× blue Fan motor error.
The fan motor was overloaded. The dust
container is probably completely full
or the central brush is heavily clogged
with dirty material. Clean out the
vacuum cleaner.
Red 2× per
second Low voltage
The battery is almost flat and the
robotic vacuum cleaner is no longer
able to travel to the charging station on
its own. It is necessary to place it into
the charging station by hand.
TROUBLESHOOTING
You can attempt to resolve problems with the operation of the vacuum cleaner
that are not indicated by audio or light signals using the following table. If you
are unsuccessful resolving the resulting situation, attempt to turn it off and then
on again using the main switch A4. If the problem persists, please contact an
authorised service centre.
PROBLEM POSSIBLE CAUSE SOLUTION
The vacuum
cleaner cannot be
turned on.
The battery is not inserted
correctly in the robotic
vacuum cleaner.
Insert the battery according
to the instructions in this
user'smanual.
The battery is flat. Charge the battery.
The vacuum
cleaner is on, but it
is not vacuuming
dust and dirt.
The dust container is full. Empty the dust container.
The dust filter is not
properly installed in the
dust container.
Properly install the dust filter
into the dust container.
The vacuum
cleaner travels
only backwards
when it is turned
on.
The vacuum cleaner was
placed on afloor that is
too dark.
Move the vacuum cleaner to
alighter-coloured floor and
start it again.
An anti-fall sensor is dirty. Clean the anti-fall sensors.
The rotary brushes
are deformed and
do not sweep up
dust and dirt.
The brushes are worn out.
Dip them in warm water to
renew their original shape.
Contact the vendor or service
centre and order new brushes.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SRV 2230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SRV 2230 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info