759970

Sencor SHP 8400 Handleiding

9
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
08/2018
- 9 -
Copyright © 2018, Fast ČR, a.s.
■ Because hair grows in various directions, it is also necessary to move the hair clipper
in various directions (upwards, downwards or crosswise).
■ Repeat individual passes so that you cut also the hair that you did not cut in the
previous passes.
■ Ensure that the flat part of the comb attachment is in full contact with the scalp. This
will ensure an even haircut result.
■ To achieve good results on curly, sparse or long hair, you can try using acomb to lead
the hair towards the hair clipper.
■ Trim beards by slowly moving counter to the growth direction of the beard, going
from the bottom upwards. When trimming beards using acomb attachment, keep in
mind that the selected comb attachment must be in constant contact with the skin
in order to ensure an even cut. After reattaching the attachment on to the cutting
unit A2, do not forget to set the cutting height again.
■ Regularly clean away hair and whiskers from the cutting unit. In the event that
alarge amount of hair or whiskers accumulates in the cutting blade, take it off the
hair clipper and blow or tap the hair or whiskers out of it.
CLEANING AND MAINTENANCE
■ Regular cleaning of the hair clipper after every use will ensure its proper operation.
■ Before you start cleaning the hair clipper, turn it off and disconnect it from the power
socket.
Attention:
This hair clipper is not designed to be washed under awater tap. Do
not spray the hair clipper or its power adapter A8 with water or any
other liquid or submerge it in water or any other liquid.
CLEANING THE CUTTING UNIT
■ Remove the comb attachment from the cutting unit A2 when it is ready.
■ Use the cleaning brush B9 to remove all hair, whiskers or body hair from the cutting
unit A2 and all the remaining attachments B1 to B8.
■ Remove the cutting unit A2 from the hair clipper, see figure E. Hold the hair clipper in
one hand so that your thumb is positioned on the underside of the cutting unit A2.
Use the thumb of the other hand to push the cutting unit from the handle A6 until
the cutting unit A1 is fully released.
Attention:
The edge of the cutting blade A1 is sharp, pay increased
attention when handling it.
■ Use the brush B9 to remove all hair or whiskers from the cutting unit A2 and from
the inner area of the hair clipper underneath the cutting unit A2.
■ After cleaning, reattach the cutting unit A2 to the handle of the hair clipper A6, see
figure F. Slide the tab on the underside of the cutting unit A2 into the cut-out in
the handle of the hair clipper A6 and then push the cutting unit A2 against the hair
clipper until an audible click is heard.
CLEANING THE COMB ATTACHMENTS
■ Comb attachments B1 toB8 can be washed under lukewarm running water. After
washing an attachment, carefully wipe it with asoft, dry cloth and then allow it to
dry naturally.
■ The hair clipper handle A6 can be cleaned using aclean dry cloth. In the event that
it is very dirty, you can use a lightly dampened cloth. Then thoroughly wipe the
cleaned surface dry.
■ To clean the power adapter A8, use aclean, dry cloth.
■ For cleaning, do not use brushes with hard bristles, cleaning products with an
abrasive effect, solvents, etc. Otherwise, the cleaned surface may be damaged.
LUBRICATING THE BLADE OF THE CUTTING UNIT
■ To ensure complete movement of the cutting unit blades A1, we recommend that it
is regularly lubricated always after several sessions.
■ If acomb attachment is mounted on the cutting unit A2, remove it.
■ Apply 1 to 2 drops of oil B10 to the blade of the cutting unit A1 and evenly spread
the oil using acloth. Dry off excess oil. Check that the cutting blade is clean before
using again.
Note:
After using up the supplied oil B10 you can use an oil that does not
contain acids, e.g. sewing machine oil.
STORAGE
■ When you have finished using it, you may store the hair clipper with all its accessories
in the supplied case B11. Keep the case with the hair clipper away from extreme
temperatures, direct sunlight and excessive humidity and do not store it in an overly
dusty environment.
TECHNICAL SPECIFICATIONS
Hair clipper
Built-in battery...............................................................................................Li-ion, 3.6 V, 2200 mAh
Output ............................................................................................................................................ 5 V, 1 A
Dimensions (width × depth × height) .......................................................... 174 × 52 × 32 mm
Weight ............................................................................................................................................... 120g
Noise level ...................................................................................................................................72 dB(A)
Power adapter
Rated voltage range .................................................................................................... 100−240 VAC
Rated frequency.......................................................................................................................50–60 Hz
Output ......................................................................................................................... 5 V/DC, 1,000 mA
Length of the power cord.........................................................................................................195 cm
The declared noise emission level of the appliance is 72 dB(A), which represents alevel
Aof acoustic power with respect to areference acoustic power of 1 pW.
EXPLANATION OF TECHNICAL TERMINOLOGY
Safety class for electrical shock protection:
IP20 – The appliance is constructed in such a way that it is not possible for any
dangerous live parts of the appliance to come into contact with the human body and
at the same time the appliance is protected against the damaging effects of water that
could enter into the appliance.
Changes to text and technical parameters are reserved.
DISPOSAL OF USED BATTERIES
Prior to handing over the hair clipper at aspecialised collection facility, it is necessary
to ensure that the built-in battery is removed. Battery removal will be performed at the
authorised service centre. In the event that the product has been disassembled for the
purpose of ecological disposal then it must not be reassembled.
This symbol indicates that used batteries do not belong in ordinary
municipal waste. Hand over used batteries to designated collection
points for proper disposal. Correct disposal of batteries will help
prevent negative impacts on the environment and human health.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of
used batteries, request the necessary information about the correct
disposal method from the local authorities or from your vendor.
INSTRUCTIONS AND INFORMATION REGARDING THE
DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at asite designated for waste in your municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC
EQUIPMENT
This symbol on products or original documents means that used
electric or electronic products must not be added to ordinary
municipal waste. For proper disposal, renewal and recycling hand over
these appliances to determined collection points. Alternatively, in
some European Union states or other European countries you may
return your appliances to the local retailer when buying an equivalent
new appliance. Correct disposal of this product helps save valuable
natural resources and prevents potential negative effects on the
environment and human health, which could result from improper
waste disposal. Ask your local authorities or collection facility for more details. In
accordance with national regulations penalties may be imposed for the incorrect
disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic appliances, ask your retailer or supplier
for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this product,
request the necessary information about the correct disposal method from the local
council or from your retailer.
This product meets all the basic requirements of EU directives related to
it.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SHP 8400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SHP 8400 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info