Handleiding Sencor SES 9200CH (pagina 10 van 12) (Engels)

758389

Verklein

Vergroot

Pagina terug

1/12

Pagina verder

- 10 - 06/2020

Warning:

To prevent the risk of injury by electrical shock, do not submerge

the appliance, power cord or power plug in water or any another

liquid.

Quick clean

■ The quick clean function is suitable for quickly removing dirty material from the

brew head A8 and the tubing lines.

1. Place acup, mug or glass underneath the brewing head A8.

2. Press button B9 once. The espresso machine will automatically start the quick

clean function. Water will automatically start flowing out of the brew head A8.

3. The quick clean process will automatically stop, however, it may also be stopped by

again pressing button B9 .

Note:

We recommend running the quick clean function after every use,

especially if you wish to brew an espresso after brewing acappuccino or

latté.

EVERYDAY CLEANING AND MAINTENANCE

■ Timely cleaning and maintenance is very important for operating the appliance and

extending its lifetime.

■ Before cleaning, turn off the appliance, disconnect it from the power socket and

allow it to cool down.

Drip tray and the coffee grounds container

■ Remove the outer drip tray A11. Empty out all its contents over asink, and wash it

using clean water and then dry it thoroughly.

■ Be careful not to burn yourself when handling the tray A11. It may contain hot water

■ Slide out the inner drip tray A10 with the coffee grounds container A9. Empty

out the coffee grounds container A9 and wash it with clean water. Then dry it

thoroughly. Empty out the inner drip tray A10 and if dirty, wipe it with aclean

dampened cloth and then dry it thoroughly.

■ Install the inner drip tray A10, coffee grounds container A9 and the outer drip tray

A11 back in their place.

Note:

If the icon B3 lights up while the espresso machine is running, it means

that the coffee grounds container A9 is full and needs to be emptied

out. If the icon B3 starts flashing, it means that the coffee grounds

container A9 is not inserted.

Steaming unit

■ Slide out and remove the service access door A7. Press the steam unit release button

A6 and take out the steaming unit A6 – see figure H. Wash it under running water

and then dry it out thoroughly.

■ Install the steaming unit A6 properly in its place and attach the service access door

A7.

Note:

If the icon B4 lights up, it means that the steaming unit A6 is not

inserted in its place or is not correctly installed. If icon B4 is flashing,

the service access door A7 is open or incorrectly installed.

Water tank

■ Take out the water tank A1, rinse it out with clean water with the addition of asmall

amount of neutral dishwashing detergent. Then rinse it out thoroughly using clean

water, dry it and put it back in its place.

Milk frothing system

■ To prevent milk from accumulating inside the brew head A8 and the formation of

undesirable odours, it is important to clean out the milk frothing system after every

use.

1. Place acup, mug or glass underneath the brewing head A8.

2. Fill the milk jug A13 with clean water.

3. Attach the connecting hose A15 to the hole in the brew head A8 – proceed

according to the instructions in section "Setting up the system for automatic

frothing".

4. Press button B10 or B11 twice.

5. The espresso machine will start pumping the water from the milk jug A13, which it

will heat up and then start dispensing hot water and steam through the dispensing

nozzle for milk frothing, which will clean it out and remove any milk remains.

6. Press the selected button again to end the cleaning process.

7. Disconnect the connecting tube A15 from the brew head A8 and disassemble the

milk frothing system: remove the lid A14 of the milk jug A13 and disconnect the

milk tube A16 and the rubber connecting piece A18.

8. Remove the cover from the brew head A8 – see figure I1.

9. Remove the milk frother by gently pulling it downwards – see figure I2.

10. Separate the milk frother into two parts – take off the rubber cover and remove the

top part from the bottom part – see figure I3.

11. Wash all the parts in clean water and then dry thoroughly. Assemble the removed

parts (in reverse sequence to their disassembly) and put them back in their place.

Note:

For athorough clean, you can also us the brush A12 – see figure I4.

Milk jug, milk tube and connecting tube

1. From the milk jug A13 remove the lid A14 and pour out the remaining contents of

the milk jug A13.

2. Remove the milk tube A16 from the milk jug A13.

3. Wash the milk jug A13, lid A14, milk tube A16 and connecting hose A15 in warm

water with asmall amount of neutral dishwashing detergent. Rinse under clean

water and dry thoroughly.

4. If necessary, you can use the needle to remove dirty material out of the holes on the

ends of the connecting tube A15 – see figure J. Before assembling, check that both

ends of the connecting tube A15 are clean and dry.

5. To thoroughly clean out the entire system, we recommend filling the milk jug A13

with clean water and then to connect it to the brew head A8 using the connecting

hose A15 through the hole in the brew head A8 – proceed according to the

instructions in section "Setting up the system for automatic frothing".

6. Press button B10 or B11 twice.

7. Allow the full contents of the milk jug A13 to flow through the brew head A8.

Coffee bean hopper

■ Only clean the coffee bean hopper A3 with aclean, dry cloth or paper towel. Do

not clean it with water.

Outer surface of the espresso machine

■ To clean the outer surface of the appliance, use aclean, lightly dampened cloth.

Then wipe everything so that it is thoroughly dry.

SELF-CLEAN FUNCTION (SELF-CLEANING)

■ If indicator B5 lights up during operation, it is necessary to start the Self-Clean

function.

■ The appliance will work best when the Self-Clean function is used regularly, at least

once per month, or more frequently based on the hardness of the water that is

used. This will extend its lifetime and improve power efficiency because limescale

deposits negatively affect electricity consumption.

1. Fill the water tank A1 all the way to the maximum water mark according to the

instructions contained in chapter "Filling the water tank".

2. Add descaling agents specially intended for descaling espresso machine type

appliances into the water tank A1. These agents can normally be purchased in

specialised electrical appliance stores or in online stores. Follow the instructions on

the manufacturer'spackaging when dosing the purchased descaling agent.

Warning:

For descaling, do not use vinegar, etc. Otherwise, the appliance

could be damaged.

3. Insert the power plug into apower socket.

4. Under the brew head A8, place acontainer with acapacity of at least 1.1 l.

5. In the stand-by mode, simultaneously press and hold down buttons B7 andB12

for 5 seconds. Abeep is made and indicator B5 and button B12 will flash.

6. To start the self cleaning process, press button B12 .

Note:

In the event that you wish to return to the stand-by mode at this

stage, press button B7 .

7. The progress of the self cleaning procedure is signalled by indicator B5 . Take

care to prevent scalding by hot water or the escaping steam. Do not interrupt the

process in this phase.

8. When the water in the water tank A1 is used up, indicator B1 and button B12

will start flashing. Empty out the remaining contents of the water tank A1 and

fill it up to the maximum water mark with clean water. When the filled water tank A1

is inserted back into the appliance, indicator B1 will turn off. The self cleaning

process will continue to run.

Note:

If necessary, empty out the container underneath the brew head

A8. Nevertheless, be careful when handling the container since

the water inside may be very hot.

9. When the self cleaning process is complete, the espresso will turn off automatically.

Sencor SES 9200CH Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info