757104
6
Verklein
Vergroot
Pagina terug
1/17
Pagina verder
EN - 4
5. INSTALLATION/CONNECTION
Basic procedure:
1. Pull the key out of the ignition and then disconnect the terminal on the car battery.
2. Correctly connect the input and output wires.
3. Install the device into the motor vehicle.
4. Reconnect the terminal on the car battery.
5. Reset the device.
Warning:
This device may only be installed in a motor vehicle with a 12 V DC power supply and
a grounded negative pole.
If you connect the ignition wire (red) and the battery wire (yellow) to the vehicle's chassis
(grounding), you may cause a short circuit, which may subsequently cause a fi re. Always
connect these wires to the power source via a fuse box.
Prior to installing the device, disconnect the negative battery terminal and perform all
electrical connections.
Insulate unconnected wires using vinyl tape or another similar material. To prevent
a short circuit, do not remove the covers on the ends of unconnected wires or terminals.
After installation, do not forget to ground this device again to the vehicle's chassis.
If the power supply is not turned on, the cause may be a short circuit of the speaker wire
or its contact with the chassis of the vehicle and the activation of the protective function.
Therefore, it is necessary to check the speaker wire.
Attention:
If your vehicle's ignition does not have the ACC position, connect the ignition wire to the
power source that can be turned on and off using the ignition key. If you connect the
ignition wire to the power source with a constant voltage supply, e.g. battery wires, this
may discharge the battery.
Install this device into the console of your vehicle. Make sure that the front panel does
not hit the lid of the console (if one exists) when opening and closing.
After installing the device, check that your vehicle's brake lights, blinkers, wipers, etc.
are working correctly.
Mount the device horizontally or at an incline of no more than 30°.
In the event that the fuse melts, fi rst make sure that the wires are not in contact and are
not causing a short circuit, and then replace the old fuse with a new one with the same
nominal values.
Connect the speaker wires correctly to the respective terminals. If sharing wires or if
you ground them to any metal part of the motor vehicle, the device may be damaged or
it may not function incorrectly.
If you connect only two speakers to the system, connect them either only to the front
output or only to the rear output (do not combine the front and rear output).
The installation and connection of this product required skill and experience. For reasons
of safety, have this work performed by professionals.
If you come across any problems during the installation, please contact a Sencor vendor.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SCT 5051BMR bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SCT 5051BMR in de taal/talen: Engels als bijlage per email.

De handleiding is 1,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info