759221
9
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
- 9 - 08/2019
Copyright © 2019, Fast ČR, a.s.
EN Convection heater
User'smanual
Prior to using this appliance, please read the user’smanual thoroughly, even in cases
where you have previously familiarised yourself with the operation of similar types
of appliances. Only use the appliance in the manner described in this user’smanual.
Keep this user’smanual in asafe place where it can be easily retrieved for future use.
We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least the
duration of the legal liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance in the original box
from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1 Display with control elements
A2 Front panel
A3 Main power switch (located on the
side)
A4 Travel wheels
A5 Wall mounting hooks
A6 Rear panel
A7 Wall mounting set (not shown)
DESCRIPTION OF THE CONTROL PANEL
B1 Button
B2 Button
B3 On/Off/Child safety lock button
B4 Programming button
B5 Operating mode button
B6 Day of the week and hour setting
button
DESCRIPTION OF THE DISPLAY
C1 Power saving mode icon
C2 Frost-free mode icon
C3 Programming icon
C4 Hours
C5 Day of the week icon
C6 Timer icon
C7 Heating icon
C8 Comfort mode icon
C9 Temperature display
C10 Lock icon
C11 Hour icon
C12 Minute icon
C13 Heating display
BEFORE FIRST USE
Before first use, take the appliance and its accessories out of the packaging material
and remove all promotional labels and stickers. Check that neither the appliance nor
any of its parts is damaged.
INSTALLATION
The convection heater may be used as amobile heat source (necessary to install
the travel wheels A4) or it may be mounted on awall (travel wheels A4 must be
removed).
Warning:
Before any type of installation, always make sure that the power
plug is disconnected from the power socket.
Installing the travel wheels
Put ablanket or another soft underlay on the floor. Then place the convection heater
upside down on to this blanket.
On the underside of the convection heater there are three drilled holes on either
side. Align these holes with the holes in the travel wheels A4 and, using the supplied
self-tapping screws, screw them to the underside of the convection heater – see
figure D. Tighten securely. Check that the travel wheels A4 are correctly attached
to the convection heater.
Turn the convection heater over and carefully put it down on the travel wheels A4.
Check that the wheels move freely and that they are not blocked in any way.
Wall mounted installation
Before mounting the convection heater on awall, it is important that you check that
the installation location has no wires, conduits, pipes, etc. in the wall.
Likewise, prior to installation, remove the travel wheels A4 if they are installed.
Prior to installation, also check that the installation location is at asufficient distance
from the power socket.
Warning:
Only use the supplied set of screws and dowels for the
installation. Under no condition should dowels and screws be
used that have adifferent diameter, different specifications and
which are not approved by the manufacturer as suitable for the
installation of this type of product.
Drill holes of 8 mm diameter 40 mm deep into the wall as shown in figure E.
Insert the plastic dowel into the drilled hole and then the screw. Using ascrewdriver,
secure the screw and leave it protruding out approximately 6 mm.
Put the convection heater on to the wall by sliding the screw heads into the holes
on the hanging hooks A5.
Warning:
The convection heater must be installed at least 15 cm above the
ground and 50 cm from the ceiling. The convection heater must
be installed horizontally. Any electrical installations must be
performed by aqualified electrician. The convection heater must
not be installed behind doors or in an outdoor environment.
USING THE CONVECTION HEATER
Prior to first use, check that the voltage in your power socket corresponds to the
voltage on the rating label.
Insert the power plug into apower socket.
Set the main switch A3 to position I(On). Asound will be made and the display A1
will be lit for ashort moment. As soon as the display A1 turns off, the convection
heater will automatically switch to the stand-by mode.
Turning the convection heater on/off
If the open lock icon is lit on the display, press the On/Off button B3 to turn the
convection heater on.
If the closed lock icon is lit on the display, hold down the On/Off button B3 for
approximately 3 seconds to cancel the child lock function. When the icon changes
to the open lock , press the On/Off button B3 to turn the convection heater on.
When the convection heater is turned on, the temperature, time, day icon, child lock
icon and heating icon C7 will be lit.
When you have finished using it, press the On/Off button B3 and the convection
heater will turn itself off, however, it will remain in stand-by mode. To completely
turn off the convection heater, set the main switch A3 to position 0 (Off) and
disconnect the power plug from the power socket.
Note:
Upon first use or after it has not been used for an extended period of
time, aslight odour may be sensed or asmall amount of smoke may
be emitted from the convection heater. This is completely normal and
will quickly disappear.
Child safety lock
The child safety lock function enables the display with the control elements A1 to be
locked and prevents accidental changes to your settings.
To turn on the lock function, hold down the On/Off button B3 for approximately
3 seconds. The closed lock icon will be lit on the display. All the control buttons
will be disabled.
To cancel the child safety lock function, hold down the On/Off button B3 for
approximately 3 seconds, until the icon changes to the open lock .
Note:
The child safety lock function can be used even when the convection
heater is running, or alternatively when it is turned off in the stand-by
mode.
Selecting an operating mode
The convection heater has three operating modes: comfort mode, power saving
mode and Frost-free mode.
Repeatedly press the button B5 to toggle between the individual modes. The icon of
the selected mode (C1, C2 or C8) will be lit on the display A1.
When the convection heater is turned on, it will run in the power saving mode and
icon C1 will be lit.
Note:
If the heating icon C7 is lit on the display A1, this means that the
convection heater is running and is heating to the set temperature. As
soon as the temperature is reached, the heating icon C7 will turn off
and only the icon of the selected mode will remain lit.
The icon C7 will intermittently turn on and off while the convection
heater is running. This is normal. The convection heater is heating to
the set temperature.
Comfort mode – when the room temperature falls 2°C below the set temperature, the
heating icon C7 will be lit and the convection heater will start. The heating icon C7 will
remain continuously lit while the appliance is heating. When the temperature rises 2°C
above the set temperature, the heating icon C7 will turn off and the convection heater
will switch to the stand-by mode.
Power saving mode – when the room temperature falls 4 °C below the set
temperature, the heating icon C7 will be lit and the convection heater will start. The
heating icon C7 will remain continuously lit while the appliance is heating. When the
temperature rises 4°C above the set temperature, the heating icon C7 will turn off and
the convection heater will switch to the stand-by mode.
Frost-free mode – this mode prevents the freezing of the convection heater and
cooling of the room in which it is located. The convection heater will start automatically
when the ambient temperature falls to 5°C. As soon as the temperature rises above
7°C, the convection heater will turn itself off.
Setting the temperature
The buttons / are used to set the operating temperature. Press button or
andthe numerical temperature value will start flashing. Use the buttons / to
set the desired temperature. To save the temperature, press the On/Off button B3
or wait approximately 10 seconds until the temperature value stops flashing. The
convection heater will automatically save the temperature setting.
You can set the temperature in the range from 15 to 35 °C.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SCF 3200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SCF 3200 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info