804503

Segway Ninebot Gokart Kit Handleiding

2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
Scan the QR code below Download in Google Play Store
or Apple's App Store
Remove the steering bar from the miniPRO Assembling and disassembling the Gokart This assembly is for adults only. Do not power on the miniPRO during assembly or disassembly.
Assembly
Check the status of the miniPRO
Operating the miniPRO
Activate the Gokart Use and charging
* Your mobile phone requires Bluetooth 4.0 or later, iOS system 8.0
or later, or Android™ 4.3 or later.
For your safety, the default values of the Gokart speed and
sensitivity are set to low. Use the app to learn how to drive
safely, then the speed limit can be gradually raised.
Follow the relevant charging instructions in the manual and the common battery maintenance and safety knowledge for
maintenance. Ninebot products are designed with overheat protection. If the vehicle temperature exceeds 104 °F (40°C),
the vehicle cannot be charged as normal. Wait until the vehicle cools to below 104 °F (40°C) before charging.
Specifications
6
4
Assembling your Gokart (Requires two adults to assemble)
Update the miniPRO firmware
1
2
3
Located under the frame. Remove
the attachment strap before
removing from the frame.
The installation direction is as shown below.
Be sure to align the steel frame with the
adapter pad as shown in the enlarged view.
5
Driving the Gokart
Install the app
Download the Segway-Ninebot app (hereinafter referred to as the app)
by any of the following methods:
Refer to the chapter “Maintenance” in the miniPRO User Manual to ensure that the tire
performance, the battery level, and the running status of the miniPRO are normal.
Turn on the phone's Bluetooth.
Press the power button to turn
on the miniPRO.
Open the app to search for and
connect your miniPRO.
e. Use the tools provided to remove the steering bar bracket from the miniPRO.
The steps are as follows:
Segway-Ninebot App
Pair your mobile phone and the miniPRO
Segway-Ninebot App
Disassembly
In the upper right corner of the app, tap Settings Firmware Update.
On the Ninebot settings page, tap "Gokart mode".
Enable "Gokart mode".
Update firmware and switch modes
Searching
Gokart0001
Gokart Mode
Gokart Mode
Gokart Kit installation tutorial
About Gokart
Vehicle
Vehicle
Firmware
Update
Gokart
Mode
Press the power button on the miniPRO to turn on the Gokart.
The Gokart will automatically power off when idle for 10 minutes.
Open the Segway-Ninebot APP and connect your Gokart.
Follow the instructions in the app to activate the Gokart
and complete the corresponding tutorial and exercises.
Place the steering
bar bracket
removal tool into
the screw holes on
the steering bar
bracket.
Fasten the two metal molds onto
the lower part of the steering bar
bracket by inserting the two nuts
from the right and the two M5
screws from the left; tighten with
a 4mm hex wrench.
Insert the M6 screw into the
screw hole on the front of
metal molds, tightening with
a 5mm hex wrench, continue
tightening the screw until the
steering bar bracket falls off
the miniPRO.
If lifting the frame by yourself, do not lift the
backside more than 19° or you may
damage the bumper.
Install the miniPRO adapter pad.
2
Plug the power extension cord into the charging port of the miniPRO,
tighten by turning clockwise.
1
Once fully assembled, make sure:
9
Place the Gokart frame on the miniPRO.
3
3
2
2
3
3
6
4
4
5
5
1
6
Pass the attachment straps through
the bottom of the miniPRO and the
strap fixing holes. Tighten the straps.
4Plug the electrical connection
cable of the Gokart into the
power extension cord. Align
the groove and do not force
the cord in.
5
Stretch the frame and adjust the length of the body:
6
Adjust the steering wheel height:
7
Install the Gokart batteries.
8
Power
button
Power
button
Please make sure the location of the logo
is correct on the straps. If not, return to
step for adjustment. Charge ports must be dry.
Press the miniPRO's power button
to turn off the Gokart.
Disconnect the electrical connection
cable.
Refer to the assembly procedure and
carry it out in reverse order.
a With both hands holding the steering wheel and the seat,
stretch the frame out to a suitable position along the
horizontal direction of the connection tube.
b Align the scalable structure of the frame with the
marking on the connection tube.
c Positioning: Use a 5mm hex wrench to press the two
screws into the holes on the left and right connection
tube in order, as shown in the figure above (The screw is
set to a depth of about 1cm for successful position).
d Tighten the 4 screws.
a Raise the steering wheel to a
suitable height.
b Insert the quick release
screw into the hole of the
corresponding height.
c Tighten the quick release nut.
d Press to fix the steering wheel
quick release components.
e Ensure the steering wheel does
not shake. Otherwise, repeat
the steps b, c, d, e.
Unscrew the battery
compartment cover and
insert batteries into the
compartment. Close and
tighten the cover.
To avoid issues that may be
caused by corrosion,
remove the batteries if not
using the Gokart for an
extended period of time.
The miniPRO adapter pad and the mini-
PRO are facing the correct direction.
The attachment straps are properly at-
tached and tightened.
The electrical connection cable is
plugged into the power extension cord.
The body length and steering wheel
height is appropriate for the rider.
The battery compartment is closed.
If anything appears to be incorrect,
stop using the Gokart and
contact after-sales
service.
< 19°
Acceleration: lightly press the throttle (right
pedal) to go forward.
Deceleration: lightly press the brake (left
pedal) to decelerate.
Steering: steer the Gokart by slightly turning the
steering wheel clockwise or counterclockwise.
Do not pump the brake pedal to decelerate.
Driving
1
Sitting on the seat, buckle the left and
right parts of the seat belt in front of you.
Fastening the seat belt
When the Gokart is stopped, double-press
the brake (left pedal). After you hear a beep,
the Gokart has switched to reverse mode.
Press the throttle to drive the Gokart in
reverse. Double-press the brake (left pedal)
again to return to forward mode.
Reversing
In the event of a situation that requires an
emergency stop, pull the hand brake handle on
the right side of the Gokart to engage the
emergency brake.
Emergency braking
Make sure the vehicle is completely stopped
before getting off. Press the miniPRO's power
button to turn off the Gokart.
Shutdown
Charge the Gokart by plugging the miniPRO
power cord into the power extension cord.
Do not connect the charger if the charge
port or power cable is wet.
Charging
Product
Supported
models Name and model
Size
Weight
Driving
Machine
Parameters
Tires
Light
Brake
Front
compartment
battery[3]
Name Ninebot Gokart Kit
N4MZ98
43.1×34.1×20.1 in (1095×865×510 mm)
Ninebot by Segway miniPRO (Model: N3M260, N3M320)
NinebotS (Model:N3M240)
After extension (Max status): 54×32×24 in (1383×822×600 mm); before extension
(Min status): 40×32×18 in (1004×822×459 mm)
Model
Vehicle size
Package size
Max payload 220 lbs (100 kg)
61.3 lbs (27.8 kg)
51-75 in (130-190 cm)
14+ years old
15 mph (24 km/h)
5 mph (8 km/h)
2 mph (3 km/h)
9 mile (15km)
2.1:1
1.6 in (40 mm)
15°
14°F~ 104°F (-10～40℃)
-4°F~ 122°F (-20～50℃)
IPX4
6 AA Batteries
20 ft (6 m)
Tire width: 3 in (80 mm); flatness ratio: 60%; hub diameter: 5 in (127 mm)
Non-inflatable hollow tire
0.2 Watt white LED light bar
Electronic brake + mechanical handbrake
Hardened road, flat road surface, slopes below 15°
The indicator comes in three colors: blue, yellow, and red. Blue means that the vehicle is in normal
condition. Yellow means that the vehicle needs to be activated or the batteries in the front compartment
need to bereplaced. Red means that the vehicle has a performance failure, and you need to open the
app to check the cause of the failure and contact the after-sales service.
Net weight
Height requirement
Recommended Age
Speed limit
Novice speed limit
Reversing speed limit
Steering ratio
Ground clearance
Traversable Terrain
Operating temperature
Storage temperature
IP rating
Model/Quantity
Front tires
Type
Headlight
Status indicator
Braking method
Braking distance[4]
Maximum slope [2]
Typical Range[1]
Power extension
cord
Four screws
already inserted
into the screw
holes.
Do not plug the power
extension cord into the
miniPRO if the power
extension cord or charge
port is wet.
Searching
MiniPro0001
a
b
b
b
c
d
cd
a
Activate the
Gokart
a. Press the power button
to turn off the miniPRO.
b. Unlock the steering bar
tool-free release, remove
the steering bar.
c. Remove the rubber plug on
the steering bar bracket.
d. Use a 4 mm hex wrench
to remove the screws in
the steering bar bracket
and pull off the bracket.
Disassembly is completed
after removing the steering
bar bracket. If you cannot
remove the bracket by
hand, continue to step e.
The Gokart is assembled by attaching the Gokart Kit to a miniPRO.
Before assembly of the Gokart, please review the miniPRO User Manual
and follow all instructions contained in it. Once the miniPRO has been
properly activated and charged you can begin assembly of the Gokart.
* This firmware update does not involve activation of the miniPRO. If you need to use the miniPRO,
please refer to the miniPRO User Manual for related operations.
Before assembly, update the app's firmware and turn
on Gokart mode.
[1] Typical Range : Under the
circumstances of full power, 154
lbs (70kg) load, and 77°F(25℃)
ambient temperature, and
measured on a flat road at an
average speed of 9 mph (15
km/h).
[2] Maximum slope: Refers to the
maximum slope that a 220 lbs
(100 kg) driver can climb at a
speed not faster than 3 mph (5
km/h).
[3] Front compartment battery:
The battery compartment inside
the frame that is used to power
the frame indicator/headlight.
When the battery is low, the blue
indicator light turns yellow and
blinks. You need to replace the
batteries yourself.
[4] Braking distance: Under the
circumstances of full power, 154
lbs (70kg) load, and measured on
a flat hard road at an average
speed of 12.4 mph (20 km/h).
Note: You can also open the App
for more specific tips.
miniPRO Assembly
Instructions
Scan the QR code on the
right to review Assembly
Instructions.
This manual uses the miniPRO as an example. If you have a Ninebot S, please watch the
video by scanning the right QR code.
Ninebot S Assembly
Instructions
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Segway Ninebot Gokart Kit bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Segway Ninebot Gokart Kit in de taal/talen: Engels als bijlage per email.

De handleiding is 3.16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info