780001
8
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
14 PLASMA 5 | BIKE OWNER’S MANUAL 2015 BIKE OWNER’S MANUAL 2015 | PLASMA 5 15
ENGLISH
ENGLISH
SEATPOST
Saddle assembly:
IMPORTANT
before assembling the saddle, make sure the seatpost saddle rail clamps
(524/525) are compatible with your saddle rails!
Measure your saddle rails height and width (HxW). Ritchey WCS Carbon One-Bolt
Saddle Rail Clamp outer-pieces specifications should be compatible with your
saddle rails.
If the saddle rails dimensions you measured are different from the saddle clamps
specifications, purchase the required saddle rail clamps parts at your retailer’s, the
following dimensions are available: 7x7mm, 8x8.5mm or 7x9.6mm.
Set the right saddle tilt and position the saddle rails so that the saddle rail clamps
are in the middle of the usable rail clamping area. Tighten the M6 screw (527) to the
specified torque (T13) to assemble the saddle.
Use the seatpost adjustment barrel to adjust your BB-Saddle horizontal offset.
Once the right offset is set, tighten the two M5 barrel screws (521) to the specified
torque (T12), in some cases, you will need to remove the saddle to access the two M5
barrel screws.
Battery/Seatpost assembly:
IMPORTANT
for electronic shifting assemble the seatpost battery mount parts (530) together so
that their concave surfaces are facing.
Put the O-ring part (531) into the groove and put the rubber part (532) in between
the two battery mount parts (530) so that one of its shoulders sticks out of the parts.
Assemble the battery mount parts (530) with the seatpost (501) by pinching the
upper end of the battery mounts and so that their pins coincide with the seatpost
low end holes.
Release the battery mounts once the pins are in position and pull apart the battery
mounts parts to leave enough space for the battery (999) to be mounted.
Once the battery mounts ribs are positioned into the battery groove, release the
battery mounts and connect the battery to the battery wire sticking out of the frame
seat tube.
Seatpost assembly:
IMPORTANT
before assembling the seatpost into the frame, make sure the rear side of the
seatpost (side where head is longer) is at the rear end of the frame.
Push gently the seatpost into the frame.
IMPORTANT
For electronic shifting: make sure the battery does not get stuck into the frame,
once the desired seatpost height is achieved pre-assemble the seatpost wedge:
position the upper wedge part (505) over the mid wedge part (504) and the low
wedge threaded part (503) below the mid wedge part.
Position the M6 wedge screw (506) into the assembly head up and pre-tighten it
over 3 turns. Position the wedge assembly into the seat tube insert in front of the
seat tube, its concave face should correspond to the seatpost front surface. Tighten
the M6 screw to the specified torque (T11) while making sure the upper surface of the
wedge coincides with the upper surface of the top tube.
Seatpost Plasma 4/5 SCOTT part number: 239318
Seat Clamp Plasma 4/5 SCOTT part number: 239544
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scott Plasma 5 - 2019 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scott Plasma 5 - 2019 in de taal/talen: Engels als bijlage per email.

De handleiding is 3.05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Scott Plasma 5 - 2019

Scott Plasma 5 - 2019 Gebruiksaanwijzing - Deutsch - 13 pagina's

Scott Plasma 5 - 2019 Gebruiksaanwijzing - Français - 13 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info