664183
12
Verklein
Vergroot
Pagina terug
1/21
Pagina verder
GENIUS
E
SCOTT 2014
BIKE OWNER’S
MANUAL
SCOTT SPORTS SA | 17 RTE DU CROCHET | 1762 GIVISIEZ | SWITZERLAND
© 2013 SCOTT SPORTS SA, ALL RIGHTS RESERVED | SCOTT-SPORTS.COM
DISTRIBUTION: SSG (EUROPE) DISTRIBUTION CENTER SA
P.E.D ZONE C1, RUE DU KIELL 60 | 6790 AUBANGE | BELGIUM | V3.2/20130710
2 scott-sports.com 3
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
The Genius should be adjusted exactly to the current
rider for reaching maximum safety and fun while riding.
All adjustments should be done at the local SCOTT
dealer or following to this manual.
In order to avoid technical problems or any harm please
contact in case of doubts your authorized SCOTT dealer.
CONTENT
Genius Concept ................................................................P. 004
Geometry/Technical Data Genius 650B/27.5” ...................................P. 005
Geometry/Technical Data Genius 29” ...........................................P. 006
TC Shock Technology/TWINLOC Levers ........................................P. 007
Basic Set-Up of the TWINLOC Remote Control ...................................P. 011
Recommended Tools for the Shock Set-Up ......................................P. 018
Set-Up Genius with FOX Nude Shock ............................................P. 019
Headset of Genius ..............................................................P. 024
Bottom Bracket Of Genius ......................................................P. 025
Adjustable BB Height/Angle Adjustment ........................................ P. 026
Front Derailleur Assembly ...................................................... P. 028
Chainguide Systems ............................................................P. 029
Genius Cable Routing ............................................................P. 031
Adjustment of Seatpost-Height ................................................. P. 035
Replaceable Drop Out Systems .................................................P. 036
Rear Brake Assembly ...........................................................P. 036
Front Fork Set-Up/Change of Front Fork ....................................... P. 037
Pivot Maintenance .............................................................. P. 037
Warranty .......................................................................P. 039
4 scott-sports.com 5
GENIUS
BIKE OWNER’S MANUAL
C JIHFB E
mm
73.8°
73.8°
73.8°
73.8°
°
100
115
135
160
3.9
4.5
5.3
6.3
mm inches
415
440
475
510
16.3
17.3
18.7
20.1
mm inches
440
440
440
440
17.3
17.3
17.3
17.3
mm inches
346
346
346
346
13.6
13.6
13.6
13.6
mm inches
-10
-10
-10
-10
-0.4
-0.4
-0.4
-0.4
mm inches
570
600
625
650
22.4
23.6
24.6
25.6
mm inches
A
67.7 °
67.7 °
67.7 °
67.7 °
S
M
L
XL
°
G
mm inches
776
777
809
815
30.6
30.6
31.9
32.1
74.3°
74.3°
74.3°
74.3°
100
115
135
160
3.9
4.5
5.3
6.3
415
440
475
510
16.3
17.3
18.7
20.1
440
440
440
440
17.3
17.3
17.3
17.3
352
352
352
352
13.9
13.9
13.9
13.9
-4
-4
-4
-4
-0.2
-0.2
-0.2
-0.2
570
600
625
650
22.4
23.6
24.6
25.6
68.2°
68.2°
68.2°
68.2°
S
M
L
XL
776
777
809
815
30.6
30.6
31.9
32.1
GENIUS 700 LOW POSITION
GENIUS 700 HIGH POSITION
Size Head
angle
Stem
length
Seat
angle
Head tube
length
BB center
to top of
seattube
Chainstay
length
BB
height
BB
oset
Eective
top tube
horizontal
Standover
height
L
mm inches
Wheel
base
M
mm inches
Reach
N
mm inches
Stack
1124 44.3 399 15.7 590 23..2
1155 45.5
1181 46.6
1208 47.6
427 16.8
449 1 7.7
470 18.5
599 23.6
609 24.0
623 24.5
1124 44.3
1155 45.5
1181 46.6
1208 47.6
404 15.9
431 17.0
454 17.9
475 18.7
587 23.1
596 23.5
605 23.8
619 24.4
60
70
80
90
60
70
80
90
ENGLISH
GENIUS CONCEPT
The new Genius is the result of 2 years of research and development for one of the
lightest trail/marathon bike frame set available on the market, hitting the scale at
below 2300 grams (5 lbs) including the frame, FOX Nude /CTD shock and the unique
TWINLOC remote control.
SCOTT’s focus was not only on lightweight but also on a durable and stiff frame with
an innovative suspension technology in combination with an optimized kinematics of
the rear swingarm.
The combination of an optimized kinematics with an extraordinary suspension
technology closes the gap between superlight dual suspension race bikes (e.g. SCOTT
Spark) and the new generation of all-mountain bikes (e.g. SCOTT Genius LT).
Genius was designed for riders looking for a dual suspended trail and marathon bike
offering a maximum rear wheel travel of 150mm (27.5”)/130mm (29”).
SCOTT does not see frame and rear shock as single components which are assembled
together on a bike, but as a concept with all these components working together and
offering an outrageous function by matching perfectly.
The Genius Concept is based on a multi-pivot technology.
The damping performance was improved in comparison to the already famous
“old” Genius, and with reworking also the kinematics we were able to reach a better
progression in the end of the stroke/travel of the swingarm.
The SCOTT system, using the Nude shock, named TC (Traction Control) will allow you
to reduce by remote control the rear wheel travel from 150 (27.5”)/130 (29”)mm to 100
(27.5”)/90(29”)mm including a more progressive spring rate but still offering a supple
break away. In addition the SAG is reduced and the geometry gets steeper.
Some models of Genius use also the FOX CTD shock which offers instead of the
Traction Mode a Platform (Ride Mode) in between Lock-out Mode and Descent Mode
No power will be lost and an optimum power transfer is guaranteed as the swingarm,
in contrary to locked or automatic-locking systems, can follow the trail surface and will
offer perfect traction and higher speed while standing on the pedals.
GEOMETRY/TECHNICAL DATA GENIUS 650B/27.5”
Travel 150/100/0mm
Suspension Ratio 2.72
Piston stroke 55mm
Shock length
(Eye to Eye)
200mm
Hardware
Mainframe
22.2mm x 6mm
Hardware
Swingarm
22.2mm x 6mm
Seatpost
diameter
31.6mm
Headset semi integr. for tapered 1 1/8-1.5
(44/54.9mm Inner diameter
of frame) or with 1 1/8 straight
(44.0mm)
Fork travel 150mm
Fork length 544mm
BB housing BB PF 92
Front derailleur Shimano E-Type/SRAM S3 direct
mount
Bearings 2 x IGUS / 6 x 6802 (24 x 15 x 5)
Max Tire Width 57mm/2.25”
6 scott-sports.com 7
GENIUS
BIKE OWNER’S MANUAL
C JIHFB E
mm
74.0°
74.0°
74.0°
74.0°
°
100
100
110
120
3.9
3.9
4.3
4.7
mm inches
415
440
475
510
16.3
17.3
18.7
20.1
mm inches
450
450
450
450
17.7
17.7
17.7
17.7
mm inches
335
335
335
335
13.2
13.2
13.2
13.2
mm inches
-35
-35
-35
-35
-1.4
-1.4
-1.4
-1.4
mm inches
570
600
625
650
22.4
23.6
24.6
25.6
mm inches
A
69.0°
69.0°
69.0°
69.0°
S
M
L
XL
°
G
mm inches
776
777
809
815
30.6
30.6
31.9
32.1
74.5°
74.5°
74.5°
74.5°
100
100
110
120
3.9
3.9
4.3
4.7
415
440
475
510
16.3
17.3
18.7
20.1
450
450
450
450
17.7
17.7
17.7
17.7
341
341
341
341
13.4
13.4
13.4
13.4
-30
-30
-30
-30
-1.2
-1.2
-1.2
-1.2
570
600
625
650
22.4
23.6
24.6
25.6
69.5°
69.5°
69.5°
69.5°
S
M
L
XL
776
777
809
815
30.6
30.6
31.9
32.1
GENIUS 900 LOW POSITION
GENIUS 900 HIGH POSITION
Size Head
angle
Stem
length
Seat
angle
Head tube
length
BB center
to top of
seattube
Chainstay
length
BB
height
BB
oset
Eective
top tube
horizontal
Standover
height
L
mm inches
Wheel
base
M
mm inches
Reach
N
mm inches
Stack
1111 44.7 395 15.6 609 24.0
1141 44.9
1167 45.9
1193 47.0
425 16.7
448 17.6
470 18.5
609 24.0
618 24.3
628 24.7
1111 44.7
1141 44.9
1167 45.9
1193 47.0
400 15.7
430 16.9
453 17.8
475 18.7
606 23.9
606 23.9
615 24.2
624 24.6
60
70
80
90
60
70
80
90
ENGLISH
GEOMETRY/TECHNICAL DATA GENIUS 29”
Travel 130/90/0mm
Suspension Ratio 2.60
Piston stroke 50mm
Shock length
(Eye to Eye)
190mm
Hardware
Mainframe
22.2mm x 6mm
Hardware
Swingarm
22.2mm x 6mm
Seatpost
diameter
31.6mm
Headset semi integr. for tapered 1 1/8-1.5
(44/54.9mm Inner diameter
of frame) or with 1 1/8 straight
(44.0mm)
Fork travel 130mm
Fork length 540mm
BB housing BB PF 92
Front derailleur Shimano E-Type/SRAM S3 direct
mount
Bearings 2 x IGUS / 6 x 6802 (24 x 15 x 5)
Max Tire Width 57mm/2.25”
The heart of the TC-System is the FOX Nude Shock made by FOX, offering three
functions which make this system possible.
The TWINLOC XL remote control lever is the evolution of the already outstanding
TRACLOC system of SCOTT.
While TRACLOC allowed only the change on the SCOTT TC rear shocks between the
SCOTT patented Lock-out, traction and full-mode on the fly from the handlebar, the
TWINLOC allows also the remote control of the front fork to shift between lock-out
and open mode at the same time when you change the modes on the SCOTT rear
shox.
In combination with FOX 34 CTD or FOX 32 CTD forks it is also possible to have a
platform mode on the fork.
The 3 modes of CTCD in combination with FOX Nude are:
- Climb Mode : lock-out rear, lock-out front
- Traction Mode: traction mode rear (incl. Geometry change and reduced travel),
platform mode front
- Descent Mode: full travel rear (Descent), full travel front
The 3 modes of CTD in combination with the FOX CTD shock are:
- Climb Mode : lock-out rear, lock-out front
- Ride Mode: platform(Ride) mode rear, platform mode front
- Descent Mode: full travel rear (Descent), full travel front
Therefore SCOTT offers 2 different TWINLOC levers with following fork/rear shock
combinations:
- FOX Nude with different rolls for FOX CTD fork and RockShox DNA 3 fork (SCOTT
Article number: 230097)
- FOX CTD with different rolls for FOX CTD fork and RockShox DNA 3 fork (SCOTT
Article number: 230098)
Please note that the FOX CTD rear shock does not offer a traction mode, but a
platform mode. In contrary to FOX Nude the air-chamber volume of the positive
chamber remains the same throughout the different modes
IMPORTANT:
You can only assemble the TWINLOC remote lever in “left side upward position” on
the handlebar.
TC SHOCK TECHNOLOGY/TWINLOC LEVERS
8 scott-sports.com 9
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
You have 3 positions of the TWINLOC remote lever.
1. LOCK OUT MODE:
the shock is locked; climbing on asphalt roads is now possible without
any power loss. Simultaneous a blow-off-system prevents the shock being
damaged in case the rider did not open the system while crossing obstacles.
2. TRACTION/RIDE MODE:
For Traction: by reducing the internal chamber volume inside the shock the
travel of the shock will be reduced to around 80% (approx. 120/104mm) the
characteristic of the air spring gets harder, the SAG is shorter and the geo-
metry steeper. This results in climbing without “bobbing” and offers still opti-
mum traction of the rear wheel.
For Ride: by adding a platform on the compression damping system the
shock will not bounce while standing on the pedals
3. DESCENT MODE:
full travel of 150/130mm (27.5”/29”)
You will find the following positions on the remote lever:
For the assembly of the remote control of the front fork lock-out 2 different
cable rolls which are changeable are existing.
The different roll for the pull of the fork remote cable can be changed within
few minutes to adapt the lever to your fork model/brand.
You will see on the downside of the roll the indication of the fork brand or the
fork model.
SCOTT offers 2 different TWINLOC levers with following fork/rear shock
combinations:
- FOX Nude with different rolls for FOX CTD fork and RockShox DNA 3 fork (SCOTT
Article number: 230097)
- FOX CTD with different rolls for FOX CTD fork and RockShox DNA 3 fork (SCOTT
Article number: 230098)
Please kindly note that the cable roll of a RockShox DNA3 or FOX CTD
fork‑lever is not interchangeable with the regular rolls of 2 step forks. You
need to use another lever!
For more details please contact your authorized SCOTT dealer.
10 scott-sports.com 11
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
To change the rolls to match another fork brand pls follow the drawings
below:
ASSEMBLY OF THE REMOTE CABLE
2. Fix the cable with the 2mm allen screw on the barrel adjuster on the fork
crown with a tightening torque of 0.9Nm/8 lb/in, cut the cable and secure
it with a cable end-cap. Please refer for this action also to the manual of
SRAM/RockShox or FOX attached to the bike.
TIP:
To check for accurate cable tension,
please try to move the plastic end
cap of the cable housing at the
barrel adjuster on the remote lever.
There should be “no-play” between
cap and barrel adjuster. In case of
“play” please turn the barrel adjuster
clockwise until “no-play”.
IMPORTANT:
Please make sure the lockout of SRAM/RockShox or FOX fork is activated
after transport correctly. Therefore please compress fork 5-10 times before
following the manual on remote cable installation and adjustment.
The lever should show on the downside of the cable roll the brand name of
the fork you are going to use. Please do not try to use a RockShox roll with a
FOX fork or vice versa.
1. To assemble the cable please bring the lever into the Descent Mode, push
the cable into the lever-eyelet as shown on drawing below, push it through
the pre-cut cable housing and fix it at the assembly unit on top of the right
side of the fork crown.
12 scott-sports.com 13
GENIUS
BIKE OWNER’S MANUAL
Parts List
L5
L1
L4
L2
L3
S6
S7
S5
S4
S3
S8
S9
S2
S1
S7
S4
ENGLISH
FOX NUDE SHOCK AND TWINLOC REMOTE
CONTROL LEVER
In the drawing of the shock and remote lever, shown below, you will see
the parts indicated with numbers which will be used in the manual for the
adjustment and setup.
S1
Front eyelet/ Shock Bolt
S2
Rear eyelet/ Shock Bolt
S3
Shock Housing
S4
Rebound-Adjuster Knob
S5
Positive Chamber Valve
S6
Remote Control Wheel
S7
Cable Fixing Screw (hidden behind remote wheel)
S8
Shock Piston
S9
SAG Indicator (o-ring on piston)
L1
Remote Lever
L2
Release button
L3
Remote Control Cables
L4
Cable Tension Screw Fork Remote
L5
Cable Tension Screw Shock Remote
14 scott-sports.com 15
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
BASIC SET-UP OF THE TWINLOC REMOTE
CONTROL OF FOX NUDE SHOCK
To ensure perfect function of the FOX Nude shock it is very important to
follow the steps shown below exactly.
On Genius Carbon frames you will find an internal cable routing.
Push the inner cable first through the remote lever in the upper cable routing
of the lever and then through the cable housing as shown below inside the
toptube.
On Genius alloy frames a regular outside cable routing, the outer cable
housing is fixed on cable mount ports with cable zippers.
1. loosen the cable fixing screw (S7) by turning it counter clockwise with a
2mm allen key.
2. insert a new cable via lever hole and cable housing and push it into the
shock as shown around the remote wheel (S6).
16 scott-sports.com 17
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
3. tighten the cable and fix the cablefixing screw (S7) by turning it clockwise
with a 2mm allen key and a max. tightening torque of 1.6Nm.
4. Check that the handlebar lever is in the traction position. Refer to the dia-
gram below.
6. push a cable end-cap on the cable until it touches the end of the cable.
Fix it by squeezing it with pliers.
5. cut the cable approx. 20mm away from the remote wheel.
Fix it by squeezing it with pliers.
18 scott-sports.com 19
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
BASIC SET-UP OF THE TWINLOC REMOTE
CONTROL OF FOX CTD SHOCK
The assembly of the remote cable and the setup of the FOX CTD rear shock
is very similar to the abovementioned assembly and setup of the FOX Nude.
For more details on the FOX CTD please follow the details shown in the
manuals of FOX attached to this bike
RECOMMENDED TOOLS FOR THE SHOCK
SET-UP
Please note that air will flow into the hose and indicator when counterchecking
the air pressure, so you have to set up again the recommended pressure after
this action.
Make sure to balance at least this air loss when you make a check of the air
pressure of the shock. Please also note that the indicators of shock pumps
have a tolerance of max. 10%.
For the set-up of the shock we recommend to use a shock pump with a scale
up to 20 bars/300 psi with a special air valve connector preventing from air
getting away while removing the pump from the shock valve, this will result in
an exact air pressure.
SET-UP GENIUS WITH FOX NUDE OR FOX CTD
SHOCK
The Set-Up of the FOX Nude or FOX CTD Shock can be easy done within a
few minutes.
IMPORTANT:
For all adjustments of the air spring the remote lever has to be in position “alltravel”
To adjust the air pressure of the air chamber of the FOX Nude or FOX CTD Shock
please refer to the following instruction:
1. Remove the valve cap of the valve (s5) located on the shock housing (s3).
2. Mount the shock pump with its adaptor on the valve
3. Please take into account that it takes some air pressure from inside the
shock to drive the indicator on the pump. Make sure to balance at least this
air loss when you make a check of the air pressure of the shock. Pls also
note that the indicators of shock pumps have a tolerance of max. 10%
4. Please use the FOX iRD App available at the iTunes App store with fol-
lowing link:
https://itunes.apple.com/us/app/fox-intelligent-ride-dynamics/
id549035102?mt=8&ign-mpt=uo%3D4)
5. After downloading the app on your mobile gear please follow the steps
shown in the app and inflate the shock according to the air pressure indica-
ted.When you reached the needed pressure remove the pump and put the
valve cap on the valve
20 scott-sports.com 21
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
The SAG should be 14mm (27.5/650B) respectively 12.5mm (29”) on the
shock piston.
To check the adjustment, please follow as shown below:
1. sit on the bike, put your feet on the pedal
2. put your feet back on the ground and stand over the bike without bouncing
the bike during this action
3. check if the o-ring (S9) on the shock piston (S8) has a distance of
14/12.5mm to the main dust wiper/seal between shock housing and piston.
- if the distance between the o-ring and the main dust wiper/seal is 14/12.5mm, the
air pressure is matching to your weight
- if the distance between the o-ring and the main dust wiper/seal is less than
14/12.5mm, the air pressure of the air chamber is too high and should be carefully
reduced by using the bleed knob of the shock pump until the distance is
14/12.5mm.
- if the distance between the main dust wiper/seal is bigger than 14/12.5mm the air
pressure of the air chamber is too low and should be increased by using the shock
pump until the distance is 14/12.5mm.
SAG
SET-UP OF REBOUND FOX NUDE OR FOX CTD
SHOCK
“Rebound” describes the speed the shock comes back to its original length
after absorbing an obstacle.
By using the rebound adjuster knob (S4) you can adjust the rebound step by step.
22 scott-sports.com 23
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
Please refer to the following instruction:
Ride your bike off a pavement (remain in the saddle) and check how many times
it bounces.
- If it bounces 1-2 times, the set up is good.
- If it bounces more than 3 times the rebound is too fast. Turn the knob 1-2
“clicks” clockwise
- If it does not bounce the rebound is too slow. Turn the knob 1-2 “clicks” counter
clockwise.
IMPORTANT:
Note that you have to mount the FOX Nude Shock always as shown below.
Mounting the rear shock in a different position can cause severe damages to
the frame, the linkage levers and the rear shock.
Same for the FOX CTD on some of the Genius models.
IMPORTANT:
After a dismantlement of the rear shock, both fixing bolts should be tighte-
ned with a tightening torque of 10Nm/88in-lbs.
If this is not done correctly the rear shock can be damaged.
SCOTT strongly recommends using only the FOX Nude (FOX CTD shock)
with the Genius bike, as we designed both parts for a perfect matching
combination with a linear suspension rate.
Also on those shock models the SAG should be 14/12.5mm.
Other Shock Models on Genius
If you want to use a different rear shock model than the one originally on the
bike, please make sure that the shock will not in any position hit the frame
and cause a damage to the frame.
Please follow the instruction below:
Please make sure that the rear shock or its accessory parts do not touch the
frame when mounting or suspending.
For doing so release the air/remove the coil, install the shock and compress
the shock completely.
If the shock touches the frame while doing so, do not use this shock in order
to avoid damage to frame, swingarm or shock.
SET-UP OF OTHER SHOCK MODELS
24 scott-sports.com 25
GENIUS
BIKE OWNER’S MANUAL
SALES DRAWING MATERIAL DAT E 04/23/2009
UNIT mm Part. No. PRD 13641 (OE)
No. Material Qty Remark
1 O-Ring 1 black
2 Top Cap 1 black
3 Seal 1 black
4 Compressure Ring 1 silver
5 ACB Bearing 1
41 x 30
45° x 45°
6 Upper Cup 1 black
7 Lower Cup 1 black
8 ACB Bearing 1
51.9 x 40 x 8
45° x 45°
9 Crown Race 1 black
Ritchey WCS Carbon Zero Tapered / PF 50-61mm / 18mm UD PRD 13636
Ritchey PRO Tapered / PF 50-61mm / 12.9mm PRD 13640
Ritchey WCS Carbon Zero Tapered / PF 50-61mm / 18mm UD
for 1 1/18 fork
PRD 14860
ENGLISH
Genius features a tapered headset and fork steerer system to match with
semi-integrated headsets of the “50-61”mm range with ID of Headtube of
44.0mm on top and 54.9mm on the lower end.
It is also possible to use forks with a standard 1 1/8” steerer tube when using
a reducer headset such as e.g.
HEADSET OPTIONS
All frames of Genius (carbon and alloy) have a BB shell for BB92PF standard.
This matches to several bearing and crankset models of Shimano, SRAM, FSA
and others.
Please note that you do not need anymore a spacer on the right side of the
bearing cup between frame housing and bearing cup.
BOTTOM BRACKET (BB) ON GENIUS
26 scott-sports.com 27
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
On Genius bikes equipped with the FOX Nude or the FOX CTD shock you can
adjust the BB height above ground in 2 positions by flipping a geometry chip
located on the linkage bar shock mount.
1. low BB for lower center of gravity over ground
2. high BB for bigger clearance between pedals/crankset and obstacles on the
ground
Genius 700 Genius 900
LOW POSITION
HEAD ANGLE 67.9° 69.0°
BB HEIGHT 345mm 335mm
HIGH POSITION
HEAD ANGLE 68.4° 69.5°
BB HEIGHT 351mm 340mm
ADJUSTABLE BB HEIGHT
IMPORTANT:
It is not possible to use this geometry chip with other shock models than the
FOX Nude or FOX CTD.
The shock might collide with parts of the frame or linkage bar.
28 scott-sports.com 29
GENIUS
BIKE OWNER’S MANUAL
229730 ISCG adaptor Genius 2013
229728 FD Mount Genius 2013 700-650B
229729 FD Mount Genius 2013 900-29
ENGLISH
The Carbon as well as the alloy frames of Genius can be fitted with ISCG
chainguide systems.
A set of all spare parts for this action can be ordered via the SCOTT
distribution with:
CHAINGUIDE
Details for the assembly on the carbon frames of Genius:
The adaptor must be used in order to assemble the chainblocker on the
ISCG05 chainguide system.
On all Genius frames you will find a Shimano E-type front derailleur but fixed
directly on the swingarm without the plate that is fixed normally between
the bottom bracket bearing cup and the bottom bracket housing of the front
triangle or a SRAM Direct Mount Type S3 FD.
Please note that you always need to use the adapter plate attached to the bike
or frame set between chainstay and front derailleur.
This adapter can be ordered at the SCOTT distribution with parts number:
FRONT DERAILLEUR (FD) MOUNTING DETAILS
Please note that the 2 sizes of the adapters are not interchangeable!
30 scott-sports.com 31
GENIUS
BIKE OWNER’S MANUAL
ENGLISH
GENIUS CABLE ROUTING
The direct and straight cable system on all our full suspension models offers
perfect shifting performance combined with lightweight and high resistance
against water and dirt.
Carbon Front frames:
The carbon frames of Genius have an internal shifting cable routing with
cable stops on the front end of the downtube as shown in the drawing below.
Please note that the inner cables
need to cross each other 1 time on
the inside of the downtube before
you pull them out through the cable
slot on the lower downside of the
downtube.
Push the cables through the cable
guide as shown below and fix the
cable guide on the downtube with
a 3mm allen key and a tightening
torque of max. 4Nm/35in/lbf.
Please note that you need to assemble the chainblocker exactly the way as
shown below and use all parts of the set.
Please also respect the different assembly positions for SRAM and Shimano front
derailleurs
For 2x10 drivetrains you need to use 2x2.5mm washers, for 3x10 drive trains
1x2.5mm washers between adaptor/frame and the chainblocker as shown above.
Details for the assembly on the alloy frames of Genius:
You can assemble the chainblocker directly on the integrated ISCG05 mount
on the BB shell.
Please respect the different assembly positions for SRAM and Shimano front
derailleurs.
32 scott-sports.com 33
GENIUS
BIKE OWNER’S MANUAL
229723 BB Cable Guide Genius (f. Carbon Frame)
USE PLASTIC GUIDE TO FIX THE BRAKE CABLE
ENGLISH
For the rear brake please assemble the cable as shown in the following
drawings:
Please keep in mind to have a minimum distance of 40mm between the brake
hose and the BB housing as abovementioned!
Please fix the brake hose and
the remote seatpost cable
housing (if applicable) on the
frame on the cable mounts with
the mount clips by following the
routing info as shown below:
Please secure the clamps with
a cable zipper as shown in the
drawing below:
The cable guide can be ordered via the SCOTT distribution with parts number:
Push the outer cable housings on the cables into the cable guide but make
sure to respect the needed length as shown in the next drawing!
Please make sure to respect the 40mm distance between the cables and the
BB (bottom bracket) housing to avoid “ghost-shifting” and/or damages on
the shift cables and brake hose.
34 scott-sports.com 35
GENIUS
BIKE OWNER’S MANUAL
229724 Cable Clamping Set Genius alloy 2013 one size
ENGLISH
Please tighten the mount bolt with a max. of 4Nm.
Please make sure to respect the 40mm distance between the cables and the
BB (bottom bracket) housing to avoid “ghost-shifting” and/or damages on
the shift cables and brake hose.
For the rear brake please assemble the cable as shown in the following drawings:
ADJUSTMENT OF SEATPOST-HEIGHT
IMPORTANT:
The seatpost has to be inserted into the seattube at a minimum of 100mm.
Never use another seatpost diameter than 31.6mm or try to use a shim/
reducer between seatpost and frame.
In addition to the derailleur cables and the brake hose you also will see a
possibility for an integrated cable routing of the seatpost remote on the
carbon version of Genius.
In order to seal the housing ports on the frame you should use the plugs
attached to the bike.
Alloy front frames:
Please fix the derailleur cable housings, the brake hose and the remote
seatpost cable housing (if applicable) on the frame on the cable mounts with
the mount clips by following the routing info as shown below:
36 scott-sports.com 37
GENIUS
BIKE OWNER’S MANUAL
219568 Brake Mount Adapt.Spacers 4mm f/185mm
ENGLISH
REAR DISC BRAKE MOUNT
Genius can be used with 3 different disc rotor sizes on the rear brake.
The rear disc brake on Genius is Postmount (PM) Standard on the left seatstay
and it is possible to use disc rotors with 180, 185 and 200mm diameter.
Please note that for the assembly
of 185 and 200mm rotors you might
need adapters/washers between
the PM port on the frame and the
brake calliper.
For 185mm rotor diameter you will
need 2 red anodized spacers that
can be ordered via the SCOTT dis-
tribution with:
For the use of 200mm rotors please use for SRAM/Avid: “+20mm” adaptor
Shimano: F180PP2
For the set up of the front fork please use the fork specific manual attached
to the bike.
We recommend using front forks with a travel of 150mm (27.5”) and 130mm
(29”), as this will not influence the geometry and alter handling of the bike.
For details on the technical length of the recommended forks please refer to
the Tech Info Chart before mentioned.
The pivot and bearings on SCOTT Genius are extremely easy to maintain.
An external treatment with a grease spray after every bike wash is all you
have to do. We do not recommend heavy grease sprays since these will leave
a film on the parts which is difficult to remove. We recommend the same for
the chain also.
If you have to change the bearings you can order them included in a service
kit at your local SCOTT dealer or buy them with international parts number as
shown above in the specs list in a hardware store.
In case of a change of the bearings or of the rear swingarm you should
contact your local SCOTT dealer as you need special tools for disassembly
and assembly.
FRONT FORK SET-UP/CHANGE OF FRONT
FORK
PIVOT MAINTENANCE
REPLACEABLE DROPOUT
On Genius bikes of model year 2013 you can replace the rear derailleur hanger.
Depending on the different models you’ll find following options:
1. 142mm axle with RWS 142/12
The complete set of RWS 142/12 is available via the SCOTT distribution with
parts number 219574, the right side replaceable RD hanger with 219577.
2. 135mm axle with RWS 135/5
The complete set of RWS 135/5 is available via the SCOTT distribution with
parts number 219572, right side replaceable RD hanger available with 219575
3. Regular 135mm rear axle with QR
The replaceable hanger is available via the SCOTT distribution with parts
number 206473.
If you want to use another RWS standard SCOTT also offers after-market parts
for specific wheelsets for the following parts via the SCOTT distribution:
RWS 135/12 parts set: 219574, right side replaceable RD hanger available with
219576
38 scott-sports.com 39
GENIUS
BIKE OWNER’S MANUAL
NOTES
ENGLISH
WARRANTY
Model .......................................................................................................
Year ..........................................................................................................
Size ..........................................................................................................
Frame Nr. ...................................................................................................
Shock Nr. ...................................................................................................
Date of purchase .........................................................................................
40
BIKE OWNER’S MANUAL
SCOTT bikes are made using the most innovative production and quality methods.
They are equipped with best components of well known parts suppliers.
Doing so SCOTT warrants its frames and swingarms for five years (subject to
compliance with maintenance ranges, see below) and SCOTT forks (provided it
is a fork of SCOTT) for two years for defects in material and/or workmanship in
case of purchase of completely assembled bikes.
This warranty of 5 years for the frames shall only be granted in case once a year a
maintenance service has been effected according to maintenance requirements
as set forth in this manual by an authorised SCOTT dealer.
The authorised SCOTT dealer shall confirm the effected annual maintenance
service by stamp and signature.
In case such an annual maintenance service has not been effected the warranty
of 5years for the frame shall be reduced to 3 years.
Costs for maintenance and service have to be born by the owner of the SCOTT bike.
On Gambler, Voltage Fr and Volt-X the warranty period is limited to 2 years.
The warranty period starts at the day of purchase. This warranty is limited to the
first buyer, what means the first person who uses the bike and only with the use
it was made for. Furthermore, this warranty is limited to purchases via authorized
SCOTT-dealers
The warranty is solely granted in case of purchase of a completely assembled
bike to the explicit exclusion of purchases of not completely assembled bikes.
In case of a warranty claim the decision to repair or to replace the defective part is up
to SCOTT. Non defective parts will only be replaced at the guarantee’s own expense.
Fair wear and tear is not covered by the warranty.
A complete list of all parts of wear and tear can be found in the next chapter of
this manual.
In addition, you will find at the end of this manual a protocol for the handing over
of the bike which will remain in copy at the SCOTT dealer after acceptance and
signature of the consumer.
It is obligatory to show this protocol of handing over together with the defective
part in case of a warranty claim given that it provides evidence of purchase.
Otherwise no warranty is granted.
In principle, this warranty is granted worldwide. Claims must be made through an
authorized dealer, for information regarding the nearest dealer, write or call this
company or the national SCOTT distributor.
Normal wear, accident, neglect, abuse, improper assembly, improper
maintenance by other than an authorized dealer or use of parts or devices not
consistent with the use originally intended for the bicycle as sold are not covered
by this warranty.
Hereby SCOTT grants a voluntarily manufacturer’s warranty. Additional
entitlements according to national warrant of merchantability are reserved.
For warranty info on the Fox Nude shock please refer to the attached manual of
Fox Nude.
WARRANTY
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scott Genius - 2014 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scott Genius - 2014 in de taal/talen: Engels als bijlage per email.

De handleiding is 11,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Scott Genius - 2014

Scott Genius - 2014 Gebruiksaanwijzing - Deutsch - 21 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info