Handleiding Scholtes pp 93 g (pagina 14 van 44) (Nederlands, Duits, Engels, Frans, Italiaans, Deens)

331799

Verklein

Vergroot

Pagina terug

1/44

Pagina verder

Adjusting the low flame

· Put the tap to the low flame position;

· Remove the tap knob and turn the adjusting screw,

situated inside of the tap stem (fig.9), using a screwdriver

(loosening the screw increases the height of the flame,

tightening decreases it).

note: the adjusting screw must be fully screwed down

for liquid gas.

· Having obtained the low flame setting required and with

the burner lit, abruptly change the position of the knob

several times from minimum to maximum and vice versa

and check that the flame does not go out.

Electrical connection

THE APPLIANCE MUST BE EARTHED

The hobs are designed to work with alternating current at

the supply voltage and frequency indicated on the rating

plate (situated under the hob or at the end of the instruction

booklet). Make sure that the local supply voltage

corresponds to the voltage indicated on the rating plate.

Connecting the supply cable to the mains electricity

supply

For models supplied without a plug, fit a standard plug,

suitable for the load indicated on the rating plate, onto the

cable and connect to a suitable socket.

To connect directly to the mains supply, a double-pole switch

with a contact separation of at least 3 mm suitable for the

load and complying with current standards and regulations,

must be fitted between the appliance and the mains supply

outlet.

The yellow-green earth wire must not be interrupted by

the switch.

The supply cable must be in such a position that no part of

it can reach a temperature of 50 °C above room

temperature.

For installation above a built-under oven, the hob and the

oven must be connected separately to the electricity supply

both for safety reasons and for easy removal of the oven if

necessary.

Do not use adapters or shunts as they could cause heating

Gas supply connection

• Check that the appliance is set for the type of gas

available and then connect it to the mains gas piping or

the gas cylinder in compliance with current regulations

and standards.

• This appliance is designed and set to work with the gas

indicated on the label situated on the actual hob. If the

gas supply is other than the type for which the appliance

has been set, proceed with replacing the corresponding

nozzles (provided), following instructions given in the

paragraph “Adaptation to different types of gas”.

• For trouble-free operation, suitable use of energy and

longer life of the appliance, make sure that the supply

pressure complies with the values indicated in the table

1 "burners and nozzles specifications, otherwise install

a special pressure regulator on the supply pipe in

compliance with current standards and regulations.

• Connect in such a way that the appliance is subjected

to no strain whatsoever.

Either a rigid metal pipe with fittings in compliance with

the standards in force must be used for connecting to the

nipple union (threaded ½"G male fitting) situated at the

rear of the appliance to the right (fig.7), or flexible steel

pipe in compliance with the standards in force, which must

not exceed 2000 mm in length. Should it be necessary to

turn the fitting, the gasket (supplied with the appliance)

must be replaced. Upon completion of installation, check

the gas circuit, the internal connections and the taps for

leaks using a soapy solution (never a flame). Also check

that the connecting pipe cannot come into contact with

moving parts which could damage or crush it. Make sure

that the natural gas pipe is adequate for a sufficient supply

to the appliance when all the burners are lit

Important: A pressure regulator, in compliance with the

standards in force, must be inserted when connecting to

a liquid gas supply (in a cylinder).

Adaptation to a different type of gas

If the hob is to be converted for use with a type of gas

other than that for which it was set in the factory (indicated

on the label to be found on the hob), the burner nozzles

should be replaced as follows:

• Remove the pan supports and the burners.

• Unscrew the nozzles “A” (fig.8) using a 7 mm socket

wrench and replace them with the ones which have a

diameter suitable for the type of gas to be used,

according to the table 1 "burners and nozzles

specifications).

• On completing the operation, replace the old rating label

with the one showing the new type of gas; the sticker is

available from our Service Centres.

fig.7

fig.8

fig.9

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Scholtes pp 93 g Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info