781668
20
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
20
GB
Work practice
Exert only moderate pressure on the workpiece so
that it can be machined at constant speed.
Instead of accelerating your work, high pressure
will cause the drive unit to slow down and even
stop, thus overloading the motor.
For your own safety, it is essential to secure small
workpieces with a screw clamp or vise.
Grinding
Place the workpiece onto the workpiece support
(4) and slowly guide the workpiece towards the
grinding wheel (3) at the desired angle to the point
where workpiece and grinding wheel make con-
tact.
Move the workpiece slightly back and forth to pro-
duce an optimal grinding result. This way the grind-
ing wheel (3) will be evenly worn. Allow the work-
piece to cool down occasionally.
Important!
If the grinding wheel becomes jammed during op-
eration, remove the workpiece and wait until the tool
reaches its top speed again.
Changing the grinding wheels
Important note: In order to prevent injuries from ac-
cidentally starting the machine the machine’s main
switch must be turned off before changing a grinding
wheel. Pull power plug!
Loosen the spark gard and the eye shield and pull
out as far as possible. Do not remove these parts!
Loosen work rest and pull out as far as possible.
Undo the screws of the grinding wheel guard (6)
and remove the guard.
Take off outside ange and the old grinding wheel,
then assmeble the new one.
Important note:
Do not remove the pieces of card board on the
sides of the wheel, as they are intended for
strengthening the grip of the Flange against the
grinding wheels.
Examine the new grinding wheels on cracks or
other visible damages and dispose if necessary.
Mount ange and nut again.
Do not tighten the screw by force. This can cause
the grinding wheel to break.
Re-install the grinding wheel guard (6) in the re-
verse order.
Mount work rest, spark guard and eye shield ac-
cording to installation instructions.
All covers and safety devices have to be properly
tted before the equipment is switched on.
The grinding wheels must rotat freely.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the equi ment to the power supply.
Warning! Never connect the plug to power source
outlet until all installations and adjustments are com-
pleted and you have read and understood sthe safety
and operation instructions.
Tool support (left and right) (Fig.1+Fig. 2+2.1)
Fasten the tool support (4) to the grinding wheel
guard (6) with the wing screw (a) and washer (b).
The distance between wheel and work rest should
not exceed 2 mm.
Spark guard with LED work lamp (left and right)
(Fig.1+Fig.3)
Fasten the spark guard (2) with LED work lamps (5)
to the grinding wheel guard (6) with two M5x8 pan
head screws (c).
The distance to the grinding wheel (3) should be not
more than 2mm. The distance between the spark
guard (2) and the grinding wheel (3) can be adjusted
by slackening the two pan head screws (c). Tighten
the screws securely.
LED work lamp (Fig.1+Fig. 4+Fig.4.1+Fig.4.2)
The lighting (5) can be switched on by pressing the
switch (d) on the lamp. The lighting is switched off
by pressing the switch again.
Open the battery compartment (Fig. 4.1) to insert/
change the batteries (2xAAA R03 1.5 V) . Insert the
batteries (2x on each side) (Fig. 4.2). If you change
the batteries dispose of the used batteries properly.
Replace the cover of the battery compartment in re-
verse order (Fig 4.1).
Safety screens (Fig. 1+Fig.5+Fig.5.1)
Install the safety screen (1) on the LED work lamp (5)
with the M5x55 mushroom head screw (e) and the
knurled head screw (f).
The guard is individually adjustable, as to protect the
users eyes during grinding process.
8. Operation
On/Off switch (8)
To switch on the equipment set the On/Off switch
(8) to position On.
Move the On/Off switch (8) to position Off to switch
off the equipment.
After switching on, wait for the equipment to reach
its maximum speed of rotation. Only then should you
begin with the grinding.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach SM200L bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach SM200L in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 3.63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info