www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
13 І 64
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
Many accidents are associated with poorly maintai-
ned power tools.
• Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are like-
ly to block less and are easier to control.
• Use the power tool, the accessories, bits, etc. in ac-
cordance with these instructions and in the manner
intended for the particular type of equipment. Take
into account the working conditions and the work
to be performed. Using power tools for operations
different from those intended can lead to hazardous
situations.
Service
• Have your electric tool repaired only by trained per-
sonnel using only genuine spare parts. This will en-
sure that your electric tool remains safe to use.
Additional safety instructions for elec-
trically operated mixing units
• The equipment must never be used in surroundings
where an explosive atmosphere exists. Never mix in
solvents or substances containing solvent that have
ashpoints below 21°C.
• Do not let the cable touch any parts of your body.
• Only use the extension cable approved for use in
the working area.
• The unit must only be started and stopped when it is
inside a mixing vessel. Ensure that the mixing ves-
sel is placed on a solid, secure base.
• Never reach into the mixing vessel with your hands
or any other object during the mixing process.
• We recommend that you always wear industrial sa-
fety gloves and safety googles when working with
the mixer.
• Wearing close-tting clothes is mandatory.
• Always allow for reaction torque
Residual risks
Even if you use this electric power tool in ac-
cordance with instructions, certain residual risks
cannot be rules out. The following hazards may
arise in connection with the equipment’s construc-
tion and layout:
• Lung damage if no suitable protective dust mask is
used.
• Damage to hearing if no suitable ear protection is
used.
• Health damage caused by hand-arm vibrations if the
equipment is used over a prolonged period or is not
properly guided and maintained.
Assembly (Fig. 2-4)
Chucking the beaters
Risk of injury! Wear protective gloves.
• The beater holders (9/10) and the beaters themsel-
ves are identied by the letters R and L.
• Push the sleeve (11/12) down and connect the
beaters (2/3) to the appropriately identied holders
(9/10).
Make sure that the pin (a) is in the groove (b) on
each beater.
• Release the sleeve. The beater is locked.
m Check the safe seating of the beaters by pulling
on them.
Start-up
Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identi-
cal to the mains data.
• Do not abuse the cord; do not use the cord to carry
or hang up the power tool or to unplug the power
tool from the mains. Keep the power cord away from
heat, oil, sharp edges or the power tool’s moving
parts. Damaged or tangled power cords will increase
the risk of electric shock.
• When operating a power tool outdoors, use only
extension cords that are approved for outdoor use.
The use of an extension cord that is adapted for out-
door use reduces the risk of electric shock.
• If working with the power tool in a damp location
cannot be avoided, use a ground fault circuit inter-
rupter. The use of a ground fault circuit interrupter
reduces the risk of electric shock. Always check
whether the mains voltage complies with the voltage
specied on the nameplate of the power tool.
Personal safety
• Stay alert. Watch what you are doing and use com-
mon sense when operating a power tool. Do not use
the power tool while you are tired or under the inu-
ence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
• Use personal protective equipment. Always wear sa-
fety glasses. Safety equipment such as a dust mask,
non-skid safety shoes, a hard hat or ear protection
depending on the type and use of the power tool will
reduce personal injuries.
• Prevent unintentional starting. Ensure that the po-
wer tool is switched off before connecting it to the
power supply and/or battery, picking it up or carrying
the tool. Carrying power tools with your nger on
the switch or energizing power tools that have the
switch on invite accidents.
• Remove any adjusting tool or wrench before turning
the power tool on. A wrench or a key which has be-
en left attached to a rotating part may induce per-
sonal injury. Do not overreach. Keep proper footing
and balance at all times. This enables you to better
control the power tool in situations which cannot be
foreseen.
• Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair
may get caught in moving parts.
• If dust extraction and collection units are installed,
make sure that these are connected and properly
used. Using such devices reduces hazards associa-
ted with dust.
Power tool use and care
• Do not force the power tool. Use the correct power
tool for your application. With the correct power tool
you will do the job better and safer at the specied
power rate.
• Do not use the power tool if it has a defective switch.
A power tool, which cannot be turned on or off with
the switch, is dangerous and must be repaired.
• Unplug the power cord from the outlet and/or re-
move the battery before making any adjustments to
the tool, changing accessories, or storing the power
tool. Such preventive safety measures prevent star-
ting the tool accidentally.
• Store idle power tools out of children’s reach. Do not
allow persons unfamiliar with the tool or these inst-
ructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
• Keep the power tools in good condition. Check that
moving parts are functioning smoothly and do not
lock, whether parts are broken or for any other con-
dition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use.
