644549
17
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
17GB
the protective covering. Have the saw repaired before
use if the protective covering and spring do not work
perfectly. Damaged parts, sticky residuals or piles of
saw dust can interfere with the working of the lower
protective cover.
c) When making an “inserted cut” that does not descri-
be a right angle, make sure that the saw is guarded
against slipping to the side. Slippage can lead to a
saw blade jam and a kickback.
d) Do not put the saw on the workbench or the oor wit-
hout making sure that the protective cover is over the
saw blade. An unprotected, running saw blade can
move the saw against the cutting direction and saw
what is in the way. Check the delay time of the saw.
9. Additional safety instructions for all
sawing with a wedge
a) Use the right wedge for the saw blade that is in use.
The wedge must be thicker than the thickness of the
steel blade but thinner than the width of the teeth.
b) Adjust the wedge as described in the operating inst-
ructions. Incorrect thickness, position or direction can
be the reason that the wedge does not effectively pre-
vent a kickback.
c) Always use a wedge, except when making an inserted
cut. Reassemble the wedge after an inserted cut. The
wedge is in the way when making an inserted cut and
can cause a kickback.
d) In order for the wedge to be effective, it must be in the
sawing gap. For short cuts, a wedge does not work to
prevent kickbacks.
e) Never run the saw with a bent wedge. Even the smal-
lest defect can slow down the closing of the protec-
tive cover.
INSTRUCTIONS FOR ALL SAWS
Do not use a sanding belt.
Make sure that the wedge is adjusted so that the di-
stance to the sprocket ring of the saw blade is not
more than 5 mm and that the sprocket ring does not
stick out more than 5 mm above the lower edge of
the wedge.
Make sure that the dust catching mechanism is cor-
rectly installed, as is described in this manual.
Wear breathing protection.
Only those saw blades recommended in the manual
should be used.
Always wear ear protection.
Replace the saw blades as described in this manual.
The maximum cut depth is 75 mm.
If the electrical cable of this tool is damaged it must be
replaced by the manufacturer or the customer service
department or a similarly qualied specialist in order to
avoid dangers.
FURTHER SPECIAL SAFETY INSTRUCTIONS FOR
CIRCULAR SAWS
a) Only use the recommended saw blades which corre-
spond to EN 847-1.
b) Do not use sanding belts.
c) Only use the manufacturer’s original saw.
Do not use any saw blades which do not correspond
to the characteristics described in these operating ins-
tructions. Saw blades may not be brought to a stop by
pressure on the machine from the side.
Make sure that the saw blade is tightly assembled and
turns in the correct direction.
10. Special Safety Instructions
Safety instructions for circular saws
- Hold the equipment on the insulated handles, when
you undertake work in which the tool being used could
come into contact with hidden electrical wires, or its
own cable. Contact with a live power source can elec-
trify the metal parts of the tool and lead to an electri-
cal shock.
11. Technical data
Dimensions
L x W x H mm
420x300x235
Saw blade ø mm / number of
teeth
210 / 36
Thickness of saw blade 1,6
Idling speed n
0
4500
Mitre square 0°-4
Depth of cut 90° mm 75
Depth of cut 45° mm 55
Weightkg 6,9
Motor V/Hz 230 / 50
Input W 1600
Protection class II
Sound pressure level
95 dB(A),
K
pA
: 3 dB (A)
Sound power level
106 dB(A),
K
wA
: 3 dB (A)
Typical weighted vibrations
a
h:
5,72 m/s
2
K: 1,5 m/s
2
Subject to technical modications!
Warning: Noise can have adverse health effects. Should
the noise level increase above 85 dB(A), you must wear
ear protection. Should the electrical supply not be opti-
mal, then the current can drop for a short time when the
machine is turned on. This can inuence other equip-
ment (for example, the blinking of a lamp). Should the
electrical capacity have a Zmax < 0.27, such disturban-
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach PL75 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach PL75 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Zweeds als bijlage per email.

De handleiding is 1,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Scheppach PL75

Scheppach PL75 Aanvulling / aanpassing - Alle talen - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info