782456
15
Verklein
Vergroot
Pagina terug
1/34
Pagina verder
15
Using an Extension Lead
The use of any extension lead will cause some loss of
power. To keep this to a minimum and to prevent over-
heating and possible motor burn-out, ask advice from a
qualified electrician to determine the minimum wire size
of the extension lead.
The extension lead should be equipped with an earthed
type plug that fits the power supply outlet at one end,
and with an earthed type socket that fits the plug of this
machine at the other end.
Operating the Tool
WARNING! Never connect the plug to the power source outlet
until all Installations and adjustments are completed and
you have read and understood the safety and operational
instructions.
Basic Pullover Mitre Saw Operations
• Always use the clamp 17 to hold the work piece firmly.
2 holes are provided for the clamp.
• Always position the work piece against the fence. Any
piece that is bowed or warped and cannot be held flat
on the table or against fence may trap the blade and
should not be used.
• Never place hands near the cutting area. Keep hands
outside the ”No Hands Zone” which includes the en-
tire table and is labelled by ”No Hands” symbols.
WARNING! To avoid injury from materials being thrown, un-
plug the saw to avoid accidental starting, and then remove
small materials.
Chop Cut (Fig. 6)
• For chop cutting, slide the cutting head to the rear
position as far as it will go, and lock the carriage 1 by
the lock handle 2.
Mitre Cut
• Make sure that the contact surface is secured in the
correct position.
• Loosen the locking handle (12), then press the lock
lever (24) and move the table to the desired angle.
The left angular position can be set continuously from
0° to 60° while the right position can be set from 0°
to 52.5°.
• Various lock levers facilitate the adjustment.
• Release the lock lever (24) and fix the angle with the
locking handle (12).
• Press the lock button (22), then the trigger switch (4)
and the clamping lever of the saw blade guard (3).
• Now lower the cutting head down gently to the work
piece. (Fig.1)
Bevel Cut
• Loosen the bevel lock handle and move the cutting
head to the desired angle. Tighten the bevel lock han-
dle.
• Activate the switch, then press the blade guard lock
lever to lower the cutting head down.
Compound Cut
• A compound cut is a combination of mitre cut and
bevel cut. Refer to the above procedures to perform
this cut.
Base Moulding
• Base moulding can be cut vertically against fence or
flat on the table. Follow the table below for reference.
Settings Vertical position
(Back of moulding is
flat against the fence)
Horizontal position
(Back of moulding is
flat on the table)
Extension fence Close to the blade Far from the blade
Bevel angle 45°
Moulding position Left side Right side Left side Right side
Inside
corner
Left
Right
Left
Right
Mitre
angle
Left at
45°
Right at
45°
Moulding
position
Bottom
against
table
Bottom
against
table
Top
against
fence
Bottom
against
fence
Finished
side
Keep left
side of
cut
Keep right
side of
cut
Keep left
side of
cut
Keep left
side of
cut
Outside
corner
Left
Right
Left
Right
Mitre
angle
Right at
45°
Left at
45°
Moulding
position
Bottom
against
table
Bottom
against
table
Bottom
against
fence
Top
against
fence
Finished
side
Keep left
side of
cut
Keep right
side of
cut
Keep right
side of
cut
Keep right
side of
cut
Crown Moulding Cut
• Crown moulding can only be cut flat on the table us-
ing this mitre saw.
• This mitre saw has special mitre stops of 31.6° left
and right and a bevel stop of 33.9° for a special crown
moulding 1 i.e. 52° between the back of the moulding
and the top flat surface that fits against the ceiling;
38° between the back of the moulding and the bottom
flat surface that fits against the wall. Refer to the fol-
lowing table for this crown moulding cut.
Settings Left side Right side
Inside corner Mitre angle 30° right 30° left
Bevel angle 33,9° 33,9°
Moulding
position
Top against
fence
Bottom against
fence
Finished side Keep left side
of cut
Keep left side
of cut
Outside corner Mitre angle 30° left 30° left
Bevel angle 33,9° 33,9°
Moulding
position
Bottom against
fence
Top against
fence
Finished side Keep right side
of cut
Keep right side
of cut
Note:
• These special stops cannot be used with 45° crown
moulding.
• Since most rooms do not have angles of exactly 90°,
fine tuning is needed and always take a test cut to
confirm the correct angles.
Pullover Cut
WARNING:
1. Never pull the cutting head assembly and spinning blade
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach MS305DB Kity bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach MS305DB Kity in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 6.61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info